Computer-Aided Engineering and Design Commons^™

Design And Manufacture Of An Aerodynamic Body That Meets Scaling Law Requirements And Survives Severe G-Load Environment For Free-Flight Testing, Anthony R. Gonzalez

Graduate Theses, Dissertations, and Problem Reports (ETD)

Design and Manufacture of an Aerodynamic Body that Meets Scaling Law Requirements and Survives Severe G-load Environment for Free-Flight Testing

Anthony Gonzalez

Developing scale models to test functionality and ascertain aerodynamic properties is critical before manufacturing full-size products. Through dimensional analysis and similitude, engineers create scale models to test any parameter of interest. This research aims to design a scale model of an aerodynamic body for repeated free-flight testing. The Froude number is the dominant scale model law used to determine the geometric, mass, and inertia scaling laws. A critical requirement for this research is that the model should be …

Use Of Bioheat Modeling To Characterize And Optimize Implantable Medical Devices And Neuromodulation Technologies, Adantchede Louis Zannou

Dissertations and Theses

Medical device development includes prototyping, benchtop characterization, preclinical studies, and clinical trials. Understanding the limitations and potential adverse effects of medical devices prior to their administration in humans is a crucial first step. Optimizing medical devices is essential to employing technology and improving patients care. Computational modeling is widely adopted as a powerful tool to predict stimulation/recording parameter optimization, rapid electrode/device prototyping, investigating novel mechanism of action, and testing working principles of any medical devices. Many implantable neuromodulation technologies including Spinal Cord Stimulation (SCS), which provide substantial therapeutic benefit for patient population with lower back pain, produces heat via the …

Finite Element Analysis Of 3d-Printed Pcl Scaffolds, Ireolu K. Orenuga, Joao Soares, Phillip D. Glass, Daeha Joung Ph.D.

UROP Posters

Finite Element Analysis of 3D-printed PCL Scaffolds for Synergizing Cellular Micro-Environment and Mechanical Stimuli to Enhance Engineered Tissue Growth in Vitro

Ireolu Orenuga,1 Phillip Glass,2 Daeha Joung,2 Joao S. Soares1

1. Department of Mechanical and Nuclear Engineering, College of Engineering, Virginia Commonwealth University
2. Department of Physics, College of Humanities & Sciences, Virginia Commonwealth University

Introduction: Tissue engineering aims to create viable and functional engineered tissues via biodegradable scaffolds and autologous cells. Scaffolds play an essential part in organizing the architecture of developing tissues and aid in the proper function of implants acutely by serving as mechanical support and long-term by …

Mechanical Design Of A Microwave Imaging Device For Breast Cancer Detection In Mri Scanners, Grace M. Player

Dartmouth College Master’s Theses

This project seeks to develop an updated version of a microwave imaging device for use in conjunction with breast MRI, improving upon existing technology and developing novel concepts for the device. It posits three primary redesign targets for updating the previous system: resizing the system height, making the device more iteration- friendly, and improving the overall manufacturability of the device by replacing custom components with commercially available alternatives. All three of these redesign targets are met in the new design, V2.0. The height is reduced by reducing antenna travel and height, embedding some components, and shortening the tank wall, resulting …

Design And Fabrication Of A Force-Displacement Control Mechanism For Bone-Surgical Tool Testing, Kenneth Nwagu

College of Graduate Studies: Theses & Dissertations

This project focuses on the design and fabrication of an experimental setup for orthopedic-tool testing, tailored for a surgical instrumentation company. The multifaceted project encompasses a literature review, conceptual design, prototyping, and rigorous testing, resulting in a versatile control system capable of assessing various orthopedic tools, including bone drills, saws, burrs, and power handpieces.

Orthopedic surgical procedures (which include cutting and/or drilling into bone) often need to be performed on bones for faster recovery. The drilling and cutting process can cause an increase in temperature at the cutting site which can cause bone necrosis. The tools also need to be …

4wd Baja Upright And Wheel Hub, Nathan Thompson, Jonathan P. Larson, Spencer D. Compan

Williams Honors College, Honors Research Projects

The University of Akron Zips Baja Team has switched to a 4-wheel-drive (4WD) vehicle as per the 2023 Baja Society of Automotive Engineers (SAE) rules. The 2022 Baja Vehicle was 2WD, thus the upright and wheel hub were designed exclusively for a 2-wheel-drive (2WD) Baja vehicle. This report entails the design process and methods of verification for the design of the 4WD upright and wheel hub.

On Blockchain Performance Enhancement: A Systematic Map Of Strategies Used, Anthony Kigombola

Tanzania Journal of Engineering and Technology (TJET)

Blockchain technology is one among the recent innovations in the computing industry. Blockchains have gathered a widespread interest in the industry mainly due to their security promise. Despite the anticipated benefits of Blockchains, there are several limitations which make the technology less suitable in large scale applications such as banking, one being low throughput. Several initiatives to improve the throughput of Blockchains are being tried out both in the academia and the business worlds but no systematic classification of the initiatives and the strategies used has been done. This study explores Blockchain performance improvement initiatives and classify the initiatives by …

Molecular Dynamics Of High Temperature Hydrogen Attack, Mike Travis Bodden Connor

Theses and Dissertations

High temperature hydrogen attack (HTHA) is a damage mechanism that only affects carbon steel and low alloy material. Most of the data regarding HTHA are experimental-driven. Even though this approach has been successful, there are still much more things that the oil and gas industry does not understand about HTHA. The regions that were considered safe (below the Nelson curves) have experienced catastrophic failure. Our research consists of performing Molecular Dynamics (MD) and the Nudge Elastic Band (NEB) calculation of HTHA to better understand the atomistic behavior of this damage mechanism.

Surrogate Model-Based Design Optimization Of A Mobile Deployable Structure For Overpressure Load And Vehicular Impact Mitigation, Daniela F. Tellkamp

Theses and Dissertations

Artificial Neural Network (ANN) ensemble and Response Surface Method (RSM) surrogate models were generated from Finite Element (FE) simulations to predict the overpressure load and vehicle impact response of a novel rapidly deployable protective structure. A Non-dominated Sorting Genetic Algorithm-II (NSGA-II) was used in conjunction with the surrogate models to determine structure topology input variable configurations which were suited to produce the optimal balance of minimum mass, minimum rotation angle, minimum displacement, and maximum total length of the deployable structure. The structure was designed to retract into a container, be lightweight to facilitate transportation, and be able to adapt to …

A Constitutive Material Model For Simulating Texture Evolution And Anisotropy Effects In Cold Spray., Creston Michael Giles

Theses and Dissertations

Cold spray has seen rapid advancement since its inception and has shown significant potential as a method of additive manufacturing. However, the large plastic deformation and repeated heating/cooling cycles that the material undergoes during the cold spray process can result in gradients in material structure and large residual stresses. The purpose of this study is to extend the existing EMMI material model to include anisotropic material response through the use of orientation distribution functions to predict residual stresses and anisotropy resulting from cold spray and similar additive manufacturing processes. Through the use of a finite element simulation, yield surfaces for …

In-Situ Tribology Of Engineered Surfaces With 3d-Printed Micro/Nano-Textures, Mahyar Afshar Mohajer

Graduate Theses and Dissertations

Surface texturing is an effective way to reduce the adhesion and friction between two contacting surfaces by reducing the real area of contact between them, providing a potential solution for adhesion and friction-induced failures, for example, failures in micro-/nano-electromechanical systems (MEMS/NEMS). Surface texturing is also essential to the realization of functional surfaces such as superhydrophobic/philic and icephobic surfaces. However, textures are prone to deformation due to being subjected to higher contact pressures. The advancement of 3D nanoprinting by two-photon lithography (TPL), combined with the ability to make an in-situ observation of the interplay between the forces and the sliding surfaces …

Design Of A System To Investigate The Relationship Between Feedback And Delivery Medium For A Novel Motor Task, Ashley Humpal

Master's Theses

Stroke is a chronic, lifelong illness, and full recovery requires continuous physical and cognitive rehabilitation. Such long-term rehabilitation is cost-prohibitive; however an approach to providing long-term therapy that has recently gained traction is the use of socially assistive agent (SAA) systems. These systems make use of non-contact communication devices and can be used to guide people through a variety of rehabilitative tasks. They have the potential supplement current rehabilitation practices by providing motivation during intense exercises, and can extend the reach of the therapist into remote and home settings.

Though SAA systems have been used in a variety of rehabilitative …

Multiscale Topology Optimization With A Strong Dependence On Complementary Energy, Dustin Dean Bielecki

All Dissertations

A discrete approach introduces a novel deep learning approach for generating fine resolution structures that preserve all the information from the topology optimization (TO). The proposed approach utilizes neural networks (NNs) that map the desired engineering properties to seed for determining optimized structure. This framework relies on utilizing parameters such as density and nodal deflections to predict optimized topologies. A three-stage NN framework is employed for the discrete approach to reduce computational runtime while maintaining physics constraints.

A continuous representation that uses complementary energy (CE) methods to solve a representative element's homogenized properties consists of an embedded structure that is …

Parametric Modeling Of Biomimetic Sharkskin For Wire Edm For Drag Reduction And Hydrophobicity, Joel Maxwell

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

This research sets out to demonstrate the viability of parametric modeling for biomimetic sharkskin in the effort to reduce drag and create a self-cleaning surface. Multiple designs were created to be machined by Wire EDM on stainless steel and titanium and were comparatively tested. Limitations of current manufacturing processes to economically produce naturally occurring structures such as sharkskin, emphasize the need to be able to calculate the most accurate design for a given manufacturing process. By designing a simplified but parametrically consistent model compared to an accurately depicted 3D model of sharkskin, the textured samples produced can be further tested …

Novelty Ice Cream Assembly Prototype, Mason Sylvester, Logan Williamson, Alvaro Martinez, Adin Gilman-Cohen

Mechanical Engineering

Cool Beans USA is a novelty ice cream startup company founded by Keith Zachow. In the winter of 2022, our team began working with Mr. Zachow to develop a machine to automate parts of the production process for his product. This product consists of two hemispherical ice-cream cone shell halves filled with soft serve ice cream and pressed together. The assembled pods are around the size and shape of a small walnut and are intended to be sold in stores as a frozen finger food. At the time of project inception, this product was in its early stages and was …

Rotating Backing Brush, Caleb Savard, David Dalal, Max Allred, Mathis Weyrich

Mechanical Engineering

In the final steps of GAF’s shingle production process, small asphalt particles called fines are applied. Some fines adhere well to the shingle sheet, while others temporarily stick only to fall off the sheet further down the manufacturing line. As a result, the shingle plant floor is covered in fines that have fallen due to vibrations and gravity. The technicians and engineers at GAF want a cleaner working environment and to potentially reuse the loose fines. We are a senior project team that solved this problem by designing a system to remove and collect loose fines. In this document, the …

Baby Soothing Device, Grace Kalene Mekrut, Matteo Gozzini, Miles Angel Ibarra, Christian Joel Roberts

Mechanical Engineering

This document is the official final design review for the Baby Soothing Device. This product is intended to help families sleep throughout the night by allowing a baby to be soothed back to sleep without constant and direct parental interaction. It is maintained by Mechanical Engineering students at California Polytechnic State University, San Luis Obispo for Dustin Yoder, the project sponsor. The purpose of this document is to present the design process from ideation to finished design in great enough detail that its manufacturing procedure may be replicated if desired. This document further explains all the research, testing, and benchmarks …

Multiple Heat Exchanger Cooling System For Automotive Applications – Design, Mathematical Modeling, And Experimental Observations, Zaker Syed

All Dissertations

The design of the automotive cooling systems has slowly evolved from engine-driven mechanical to computer-controlled electro-mechanical components. With the addition of computer-controlled variable speed actuators, cooling system architectures have been updated to maximize performance and efficiency. By switching from one large radiator to multiple smaller radiators with individual flow control valves, the heat rejection requirements may be precisely adjusted. The combination of computer regulated thermal management system should reduce power consumption while satisfying temperature control objectives. This research focuses on developing and analyzing a multi-radiator system architecture for implementation in ground transportation applications. The premise is to use a single …

Using Strategic Options Development And Analysis (Soda) To Understand The Simulation Accessibility Problem, Andrew J. Collins, Ying Thaviphoke, Antuela A. Tako

Engineering Management & Systems Engineering Faculty Publications

Simulation modelling is applied to a wide range of problems, including defense and healthcare. However, there is a concern within the simulation community that there is a limited use and implementation of simulation studies in practice. This suggests that despite its benefits, simulation may not be reaching its potential in making a real-world impact. The main reason for this could be that simulation tools are not widely accessible in industry. In this paper, we investigate the issues that affect simulation modelling accessibility through a workshop with simulation practitioners. We use Strategic Options Development and Analysis (SODA), a problem-structuring approach that …

28 Ghz Patch Antenna Array With Reduced Mutual Coupling For 5g Communications Systems, Rahabu F. Mwang’Amba, Hashimu Uledi Iddi

Tanzania Journal of Engineering and Technology (TJET)

A 28 GHz patch antenna array with reduced mutual coupling for 5G communication systems is presented in this paper. Two elements antenna array was simulated with a periodic boundary to represent an infinity array. The antenna array is attached with a pair of the coupled directional coupler with a coupling value of -3.47 dB, and transmission lengths of 3.40 mm and 7.62 mm depending on the antenna array's magnitude and phase coefficient were designed and simulated. A reduced mutual coupling of -31.86 dB compared to -10.75 dB for an array without a decoupling network was observed. The wide scanning angle …