Semiconductor and Optical Materials Commons^™

Orientation-Dependent Pseudomorphic Growth Of Inas For Use In Lattice-Mismatched Mid-Infrared Photonic Structures, Gregory Edward Triplett, Charles Meyer, Emily Cheng

Electrical and Computer Engineering Publications

In this study, InAs was deposited on GaAs (100) and GaAs (111)B 2 degrees towardssubstrates for the purpose of differentiating the InAs growth mode stemming from strain and then analyzed using in-situ reflection high energy electron diffraction, scanning electron microscopy, Raman spectroscopy, reflectance spectroscopy, and atomic force microscopy. The procession of InAs deposition throughout a range of deposition conditions results in assorted forms of strain relief revealing that, despite lattice mismatch for InAs on GaAs (approximately 7%), InAs does not necessarily result in typical quantum dot/wire formation on (111) surfaces, but instead proceeds two-dimensionally due primarily to the surface orientation.

Stm Study Of Pulsed Laser Assisted Growth Of Ge Quantum Dot On Si(1 0 0)-(2 × 1), Ali Orguz Er, Hani E. Elsayed-Ali

Electrical & Computer Engineering Faculty Publications

Ge quantum dot formation on Si(1 0 0)-(2 × 1) by nanosecond pulsed laser deposition under laser excitation was investigated. Scanning tunneling microscopy was used to probe the growth mode and morphology. Excitation was performed during deposition using laser energy density of 25-100 mJ/cm ². Faceted islands were achieved at a substrate temperature of ∼250 °C only when using laser excitation. The island morphology changes with increased laser excitation energy density although the faceting of the individual islands remains the same. The size of the major length of islands increases with the excitation laser energy density. A purely electronic …

Polarization Of Bi2te3 Thin Film In A Floating-Gate Capacitor Structure, Hui Yuan, Kai Zhang, Haitao Li, Hao Zhu, John E. Bonevich, Helmut Baumgart, Curt A. Richter, Qiliang Li

Electrical & Computer Engineering Faculty Publications

Metal-Oxide-Semiconductor (MOS) capacitors with Bi₂Te₃ thin film sandwiched and embedded inside the oxide layer have been fabricated and studied. The capacitors exhibit ferroelectric-like hysteresis which is a result of the robust, reversible polarization of the Bi₂Te₃ thin film while the gate voltage sweeps. The temperature-dependent capacitance measurement indicates that the activation energy is about 0.33 eV for separating the electron and hole pairs in the bulk of Bi₂Te₃, and driving them to either the top or bottom surface of the thin film. Because of the fast polarization speed, potentially excellent …

Investigation Of The Effects Of Rapid Thermal Annealing On Mbe Grown Gaasbi/Gaas Heterostructures For Optoelectronic Devices, Perry C. Grant

Graduate Theses and Dissertations

High efficiency optoelectronic devices rely on high quality materials making up the device structure. The scope of this thesis investigates the effectiveness of rapid thermal annealing (RTA) at improving the material quality of GaAsBi/GaAs heterostructures. During the fabrication of a device, the contacts of the device had the rapid thermal annealing process accomplished to produce ohmic contacts and this research explored if this annealing treatment degraded the quantum wells that made up the active region of a device. To investigate these effects, a system to measure the photoluminescence of the material system was constructed utilizing Fourier Transform Infrared Spectroscopy. The …

Monodentate, Bidentate And Photocrosslinkable Thiol Ligands For Improving Aqueous Biocompatible Quantum Dots, Hiroko Takeuchi

Graduate Theses and Dissertations

Water-soluble Quantum Dots (QDs) are highly sensitive fluorescent probes that are often used to study biological species. One of the most common ways to render QDs water-soluble for such applications is to apply hydrophilic thiolated ligands to the QD surface. However, these ligands are labile and can be easily exchanged on the QD surface, which can severely limit their application. As one way to overcome this limitation while maintaining a small colloidal size of QDs, we developed a method to stabilize hydrophilic thiolated ligands on the surface of QDs through the formation of a crosslinked shell using a photocrosslinking approach. …

Zinc Oxide Nanorod Based Ultraviolet Detectors With Wheatstone Bridge Design, Arun Vasudevan

Graduate Theses and Dissertations

This research work, for the first time, investigated metal semiconductor-metal (MSM) zine oxide (ZnO) nanorod based ultra-violet (UV) detectors having a Wheatstone bridge design with a high

responsivity at room temperature and above, as well as a responsivity that was largely independent of the change in ambient conditions. The ZnO nanorods which acted as the sensing element of the detector were grown by a chemical growth technique. Studies were conducted to determine the effects on ZnO nanorod properties by varying the concentration of the chemicals used for the rod growth. These studies showed how the rod diameter and the deposition …

Silver Oxide-Graphene Sensor For Hydrogen Peroxide, Austin D. Scherbarth, L Stanciu

The Summer Undergraduate Research Fellowship (SURF) Symposium

A nonenzymatic, amperometric sensor for Hydrogen Peroxide (H₂O₂) was designed by drop coating glassy carbon electrodes (GCEs) with Silver Oxide (Ag₂O). Combining Ag₂O with Graphene Oxide and a polymer, PEDOT, was also attempted in order to increase stability and electrochemical properties. Using metal oxides along with Graphene Oxide for sensors has been done quite a bit, but Ag₂O itself has not been research extensively. So, in order to produce the best H₂O₂ sensor, the configuration of all components had to be optimized. Three different Ag₂O …

Intermetalic Growth Rate In Transient Liquid Phase Sintering Of Pb-Free Solder Interconnects, Shuqing Zhang, John Blendell

The Summer Undergraduate Research Fellowship (SURF) Symposium

Following the electron devices are widely used in daily life, Pb-free solder alloy, as the replacement of Pb solder joint material, needs extensive researches to observe the properties for using and simulation purpose. Solder are used as the joint to connect two work pieces in printed wiring board of electronics. Most lead-free solders comprise tin (Sn) as the majority component, and nominally pure b-Sn is the majority phase in the microstructure of these solders. The most important thing for solder joint that researchers care about is its life cycle. Due to the incomplete of the mechanical profile of Pb-free solder …

Stanford Stratified Structure Solver (S4) Simulation Tool, Chang Liu, Xufeng Wang, Peter Bermel

The Summer Undergraduate Research Fellowship (SURF) Symposium

The Stanford Stratified Structure Solver (S4) developed in 2012 allows for fast, accurate prediction of optical propagation through complex 3D structures. However, there have been two key challenges preventing wider use to date: the use of a specialized control language, and the difficulty of incorporating realistic materials parameters. In this project, both concerns have been addressed. We have constructed a graphical user interface as an alternative, using the open-source Rappture platform on nanoHUB. This has been combined with a comprehensive materials database known as PhotonicsDB, which incorporates materials optical data drawn from carefully vetted sources. An Octave script file was …

Assessing The Mvs Model For Nanotransistors, Siyang Liu, Xingshu Sun, Mark S. Lundstrom

The Summer Undergraduate Research Fellowship (SURF) Symposium

A simple semi-empirical compact MOSFET model has been developed, which is called MIT virtual source (MVS) model. Compare to other model used in industry, MVS model requires only a few parameters, most of which can be directly obtained from experiment, and produce accurate results. One aim of this paper is to test the applicability of the MVS model to transistor made from MoS₂ rather than silicon. Another target is to determine the sustainability of the MVS model under different transistor tests. To achieve these goals, the MVS model will be used to fit the experimental data on MoS_{2 …}

Fabrication And Characterization Of A Palladium/Porous Silicon Layer, Nicholas Hong Lui

Master's Theses

When porous silicon is plated with a catalytic metal, the two materials can act together as a single entity whose electrical properties are sensitive to its environment – the sensing component of an electrochemical gas sensor. Etching pores into silicon is an electrochemical process; and which type of doped silicon used is one of its key parameters. For nearly all reported porous silicon gas sensors, the silicon has been of the p-doped variety – because p-doped porous etching is better understood and the layers that result from it are more predictable – despite n-doped silicon having potentially significant benefits in …

Metal-Assisted Etching Of Silicon Molds For Electroforming, Ralu Divan, Dan Rosenthal '14, Karim Ogando, Leonidas E. Ocola, Daniel Rosenmann, Nicolaie Moldovan

Student Publications & Research

Ordered arrays of high-aspect-ratio micro/nanostructures in semiconductors stirred a huge scientific interest due to their unique one-dimensional physical morphology and the associated electrical, mechanical, chemical, optoelectronic, and thermal properties. Metal-assisted chemical etching enables fabrication of such high aspect ratio Si nanostructures with controlled diameter, shape, length, and packing density, but suffers from structure deformation and shape inconsistency due to uncontrolled migration of noble metal structures during etching. Hereby the authors prove that a Ti adhesion layer helps in stabilizing gold structures, preventing their migration on the wafer surface while not impeding the etching. Based on this finding, the authors demonstrate …

Low Volume Dispensing With High Speed Dispensers, Sunny Agarwal

Graduate Dissertations and Theses

With the high pace of innovation in the semiconductor manufacturing industry, there has been an increasing demand for more energy efficient and environmental friendly products. This research relates to a complex process of fluid dispensing at low volumes on a printed circuit board. Currently, a more refined non-contact dispensing terminology named “Streaming” is widely used to stream out material at low volumes for various applications. The key solution is to frame a dispensing method that lends itself most closely to the requirements of a specific production process.

This study represents a detailed approach of dispensing low volumes of materials in …

The Design And Fabrication Of An Electrostatically Actuated Diaphragm With A Silicon-On-Insulator Wafer, Elizabeth L. Brooks

Master's Theses

Electrostatically actuated silicon membranes were designed, modeled, fabricated, and characterized. The intended application was for use in a microspeaker. Fabrication issues necessitated the use of thick diaphragms with a large gap between the electrodes. The devices did not function as speakers but did show actuation with a high DC voltage. Device dimensions were chosen by examining membrane mechanics, testing the processing steps required for device fabrication, and modeling with COMSOL. Several adhesives were researched to fabricate the device sidewalls, including BCB, PMMA, and TRA-Bond F112. A method for patterning PMMA through photolithography was found using a scanning electron microscope. Masks …

Optical And Mechanical Investigation Of Inas /Gaas Quantum Dots Solar Cells And Inas Nanowires For The Application Of Photovoltaic Device, Yushuai Dai

Theses

Self-assembled quantum dots (QDs) and nanowires (NWs) are currently the subjects of extensive study due to their promising applications in optoelectronic devices. In order to enhance understanding of the short circuit current improvement in InAs/GaAs quantum dots solar cell (QDSC), the mechanisms of carrier escape by thermal activation and tunneling from InAs quantum dots (QDs) confinements in InAs/GaAs QDSCs are investigated. The fitted activation energy of electrons from temperature dependent photoluminescence (TDPL) is 114 meV. Using this fitted activation energy, calculated thermal escape time and tunneling time of electrons from the ground state of the QDs are 10-12 seconds and …

Constructing And Optimizing A Single Wafer Solar Cell Array In The Microfabrication Lab At California Polytechnic State University At San Luis Obispo, Rod Marstell

Master's Theses

CONSTRUCTING AND OPTIMIZING A SINGLE WAFER SOLAR CELL ARRAY IN THE MICROFABRICATION LAB AT CALIFORNIA POLYTECHNIC STATE UNIVERSITY AT SAN LUIS OBISPO

Solar cells are more and more becoming a significant source of energy in the world today. They are used to power entire buildings as well as small devices and everything in between, and are utilized all around the world. Smaller solar devices, such as hearing aid battery chargers, cost a lot of money relative to the monetary wealth in third-world countries. For this purpose, a less expensive, more efficient solar cell array should be developed.

This study contains …

Fe, Co And Ni Adatoms Adsorbed On Silicene: A Dft Study, Kent Gang '14, Siva Gangavarapu '14, Matthew Deng '14, Glenn W. "Max" Mcgee, Ron Hurlbut, Michael Lee Dao Kang, Sean Ng Peng Nam, Harman Johll, Tok Eng Soon

Student Publications & Research

Two-dimensional materials have attracted much research attention given their intriguing properties. The latest member of this class of materials is silicene. In this work, we investigate the adsorption of Fe, Co and Ni adatoms on silicene using plane-wave density functional theory calculations within the Perdew-Burke-Ernzerhof parameterization of the generalized gradient approximation for the exchange-correlation potential. In particular, we calculate the binding energy, magnetization, and projected electronic configurations of these adatoms adsorbed at different sites on the silicene. Our calculations show that the hole site (i.e. in the centre of a hexagonal-like arrangement of Si atoms) is the most stable configuration …

The Fabrication & Characterization Of An Electrokinetic Microfluidic Pump From Su-8, A Negative Epoxy-Based Photoresist, Nash Anderson

Master's Theses

Microfluidics refers to manipulation, precise control, and behavior of fluids at the micro and nanoliter scales. It has entered the realm of science as a way to precisely measure or mix small amounts of fluid to perform highly controlled reactions. Glass and polydimethylsiloxane (PDMS) are common materials used to create microfluidic devices; however, glass is difficult to process and PDMS is relatively hydrophobic. In this study, SU-8, an epoxy based (negative) photoresist was used to create various electrokinetic microfluidic chips. SU-8 is commonly used in microelectromechanical design. Spin coating of various SU-8 formulations allows for 1 μm to 100 μm …

Fluorescence Characterization Of Quantum Dots For Use As Biomarkers, Logan M. Grimes

Materials Engineering

Fluorescence profiles of quantum dots (QDs) were characterized to select the ideal QDs for encapsulation in phospholipids for use as biomarkers to selectively adhere to cancer cells. QDs were synthesized and extracted 0, 30, 60, and 90 seconds after precursor compounds were mixed. These extractions were isolated by extraction time. Portions from each vial were coated in a zinc sulfide shelling procedure, leaving at least half of the QD solution unshelled. These samples were characterized over four days to monitor fluctuations in fluorescence. This was done utilizing an Ocean Optics spectrometer in conjunction with Spectra Suite software. The central wavelength, …

Scanning Tunneling Spectroscopy Under Atmospheric Conditions To Characterize A Tungsten Tip Stm System For Use With Hydrogen Desorption, Ross Gregoriev

Materials Engineering

The electrical surface structure of (111) n-type silicon was investigated through the use of scanning tunneling spectroscopy (STS) to develop a model to determine oxide presence on a passivated silicon surface. I-V curves were obtained with a scanning tunneling microscope (STM) using a tungsten tip on various locations of passivated silicon while the passivation layer desorbed from the surface under standard atmospheric conditions. The derivative (dI/dV) of these curves then revealed the electronic structure of the surface of the sample. Through these scans, it was determined the system was operating in the same mode as a Shockley diode. The separation …