Semiconductor and Optical Materials Commons^™

Beyond Conventional C-Plane Gan-Based Light Emitting Diodes: A Systematic Exploration Of Leds On Semi-Polar Orientations, Morteza Monavarian

Theses and Dissertations

Despite enormous efforts and investments, the efficiency of InGaN-based green and yellow-green light emitters remains relatively low, and that limits progress in developing full color display, laser diodes, and bright light sources for general lighting. The low efficiency of light emitting devices in the green-to-yellow spectral range, also known as the “Green Gap”, is considered a global concern in the LED industry. The polar c-plane orientation of GaN, which is the mainstay in the LED industry, suffers from polarization-induced separation of electrons and hole wavefunctions (also known as the “quantum confined Stark effect”) and low indium incorporation efficiency that …

Turning An Organic Semiconductor Into A Low-Resistance Material By Ion Implantation, Beatrice Fraboni, Alessandra Scidà, Piero Cosseddu, Yongqiang Wang, Michael Nastasi, Silvia Milita, Annalisa Bonfiglio

Nebraska Center for Energy Sciences Research: Publications

We report on the effects of low energy ion implantation on thin films of pentacene, carried out to investigate the efficacy of this process in the fabrication of organic electronic devices. Two different ions, Ne and N, have been implanted and compared, to assess the effects of different reactivity within the hydrocarbon matrix. Strong modification of the electrical conductivity, stable in time, is observed following ion implantation. This effect is significantly larger for N implants (up to six orders of magnitude), which are shown to introduce stable charged species within the hydrocarbon matrix, not only damage as is the case …

Ellipsometric Characterization Of Silicon And Carbon Junctions For Advanced Electronics, Alexander G. Boosalis

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Ellipsometry has long been a valuable technique for the optical characterization of layered systems and thin films. While simple systems like epitaxial silicon dioxide are easily characterized, complex systems of silicon and carbon junctions have proven difficult to analyze. Traditional model dielectric functions for layered silicon homojunctions, a system with a similar structure to modern transistors, often have correlated parameters during ellipsometric data analysis. Similarly, epitaxial graphene as grown from thermal sublimation of silicon from silicon carbide or through chemical vapor deposition, tend to have model dielectric function parameters that correlate with the optical thickness of the graphene due to …

A Platform For Fast Detection Of Let-7 Micro Rna Using Polyaniline Fluorescence And Image Analysis Techniques, Partha P. Sengupta

Master's Theses

The project describes a new strategy for transducing hybridization events through modulating intrinsic properties of the electroconductive polymer polyaniline (PANI). When DNA based probes electrostatically interact with PANI, its fluorescence properties are increased, a phenomenon that can be enhanced by UV irradiation. Hybridization of target nucleic acids results in dissociation of probes causing PANI fluorescence to return to basal levels. By monitoring restoration of base PANI fluorescence as little as 10^-11 M (10 pM) of target oligonucleotides could be detected within 15 minutes of hybridization. Detection of complementary oligos was specific, with introduction of a single mismatch failing to …

Imaging Thermal Conductivity With Nanoscale Resolution Using A Scanning Spin Probe, Abdelghani Laraoui, Halley Aycock-Rizzo, Yang Gao, Xi Lu, Elisa Riedo, Carlos A. Meriles

Advanced Science Research Center

The ability to probe nanoscale heat flow in a material is often limited by lack of spatial resolution. Here, we use a diamond-nanocrystal-hosted nitrogen-vacancy centre attached to the apex of a silicon thermal tip as a local temperature sensor. We apply an electrical current to heat up the tip and rely on the nitrogen vacancy to monitor the thermal changes the tip experiences as it is brought into contact with surfaces of varying thermal conductivity. By combining atomic force and confocal microscopy, we image phantom microstructures with nanoscale resolution, and attain excellent agreement between the thermal conductivity and topographic maps. …

Volatile Condensible Material Deposition In Leo Simulated Environment, Jinya Pu

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Room Temperature Vulcanized (RTV) silicone and compounds are widely used in outer-space for bonding or potting spacecraft components. In geosynchronous equatorial orbit (GEO), the silicone may outgas species which can condense on optically sensitive surfaces and degrade their performance, therefore shortening the lifetime of spacecraft. In low-earth-orbit (LEO), the silicone rubber is subject to an energetic and corrosive environment. Atomic oxygen (AO) and ultraviolet radiation can cause abrasion and degradation of the silicone rubber, cause changes in existing condensed VCM films and affect the properties of VCM films condensing in this atmosphere. Experiments were performed to simulate GEO conditions. In …

Molecular Helices As Electron Acceptors In High-Performance Bulk Heterojunction Solar Cells, Yu Zhong, M. Tuan Trinh, Rongsheng Chen, Geoffrey E. Purdum, Petr P. Khlyabich, Melda Sezen, Seokjoon Oh, Haiming Zhu, Brandon Fowler, Boyuan Zhang, Wei Wang, Chang-Yong Nam, Matthew Y. Sfeir, Charles T. Black, Michael L. Steigerwald, Yueh-Lin Loo, Fay Ng, X.-Y. Zhu, Colin Nuckolls

Publications and Research

Despite numerous organic semiconducting materials synthesized for organic photovoltaics in the past decade, fullerenes are widely used as electron acceptors in highly efficient bulk-heterojunction solar cells. None of the non-fullerene bulk heterojunction solar cells have achieved efficiencies as high as fullerene-based solar cells. Design principles for fullerene-free acceptors remain unclear in the field. Here we report examples of helical molecular semiconductors as electron acceptors that are on par with fullerene derivatives in efficient solar cells. We achieved an 8.3% power conversion efficiency in a solar cell, which is a record high for non-fullerene bulk heterojunctions. Femtosecond transient absorption spectroscopy revealed …

Morphology-Property Relationship For Binary Organic Thin Films, Alyssa Lynn Griffin

Master's Theses

Organic thin films can be readily mass-produced through solution-based fabrication methods including ink-printing and solution-casting because their light weight, flexibility, and inexpensive sources. Their applications range from organic field-effect transistors (OFET), organic solar cells (OSC), to organic light emitting diodes (OLEDs). Compared with pure component films, binary organic thin films (BOTF) allows for novel characteristics and specialized features to handle more demanding tasks. Due to the complex intermolecular interactions in BOTF, various microscopic phases with different morphological and electronic properties may be formed and this information is difficult to extract through conventional bulk measurements.

Organic thin films can be readily …

Efficiency Enhancement In Solution Processed Organic And Organic–Inorganic Hybrid Perovskite Solar Cells, Zhengguo Xiao

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Solution processed thin film photovoltaic devices are one of the most promising renewable energy sources. Organic solar cells have been intensively studied due to their advantages of light-weight, flexibility and low-cost materials and manufacturing. The organic-inorganic hybrid perovskite materials have recently shown great potential application in solar cells. The PCE increased dramatically from 3.8% in 2009 to a certified efficiency of 20.1% in 2014. In this dissertation, we focus on the efficiency enhancement for solution processed organic and organic-inorganic solar cells.

In Chapter 2, I demonstrated that the crystallinity of the ferroelectric polymer P(VDF-TrFE) at the organic active layer/ electrode …

Spectrally-Resolved Imaging Of The Transverse Modes In Multimode Vcsels, Stephan A. Misak, Dan G. Dugmore, Kirsten A. Middleton, Evan R. Hale, Kelly R. Farner, Kent D. Choquette, Paul O. Leisher

Rose-Hulman Undergraduate Research Publications

Vertical-cavity surface-emitting lasers (VCSELs) enable a range of applications such as data transmission, trace sensing, atomic clocks, and optical mice. For many of these applications, the output power and beam quality are both critical (i.e. high output power with good beam quality is desired). Multi-mode VCSELs offer much higher power than single-mode devices, but this comes at the expense of lower beam quality. Directly observing the resolved mode structure of multi-mode VCSELs would enable engineers to better understand the underlying physics and help them to develop multi-mode devices with improved beam quality. In this work, a low-cost, high-resolution (<3 >pm) …

Minimizing Sheet Resistance Of Organic Photovoltaic Cell Top Contact Electrode Layer: Silver Nanowire Concentration Vs. Conductive Polymer Doping Concentration, Caitlyn Cook

Materials Engineering

The top contact electrode layers of nine organic photovoltaic cells were prepared with two varying factors: three Silver nanowire (AgNW) densities deposited on a conductive polymer doped with three concentrations. Silver’s low sheet resistance of 20-Ω/sq is hypothesized to lower the sheet resistance of the anode layer and thus enhance the overall efficiency of the cell. Four-point probe measurements indicated that increasing AgNW density in the top contact electrode layer of an organic photovoltaic cell significantly reduces sheet resistance from 52.2k-Ω/sq to 18.0 Ω/sq. Although an increase in doping concentration of the conductive polymer reduced sheet resistance in low AgNW …

Effect Of Surfactant Architecture On Conformational Transitions Of Conjugated Polyelectrolytes, Greg A. Braggin

Master's Theses

Water soluble conjugated polyelectrolytes (CPEs), which fall under the category of conductive polymers, possess numerous advantages over other conductive materials for the fabrication of electronic devices. Namely, the processing of water soluble conjugated polyelectrolytes into thin film electronic devices is much less costly as compared to the processing of inorganic materials. Moreover, the handling of conjugated polyelectrolytes can be performed in a much more environmentally friendly manner than in the processing of other conjugated polymers because conjugated polyelectrolytes are water soluble, whereas other polymers will only dissolve in toxic organic solvents. The processing of electronic devices containing inorganic constituents such …

Photocatalytic Mineralization Of Phenol On Fluidized Titanium Oxide-Coated Silica Gel, Guillermo J. Rincon

LSU New Orleans Theses and Dissertations

A bench-scale tubular reactor with recirculation was built in order to study the efficiency of the photocatalytic oxidation of phenol on fluidized titanium oxide-coated silica gel beads. A UV-C lamp placed along the central vertical axes of the reactor was used as source of photons. A bed of silica gel beads was fluidized by means of fluid recirculation and forced to follow upward helical flow around the lamp. Anatase was successfully synthetized on silica gel particles of average diameters 224, 357 and 461 µm, as confirmed by scanning electron micrographs, through a sol-gel technique using a titanium (iv)isopropoxide / hydrochloric …

Variability In The Fabrication Process Of Bivo4 Photoanodes, Lauren M. Phillips

Senior Honors Projects, 2010-2019

Hydrogen gas produced from the photoelectrochemical (PEC) decomposition of water, using sunlight as an energy source, is a promising approach for sustainable fuel production. This decomposition of water is also called artificial photosynthesis. A device that accomplished this process is sometimes call an artificial leaf, which mimics nature inasmuch as it stores solar energy as a chemical fuel (e.g., hydrogen) by splitting water, in this way imitating natural photosynthesis. In 2009, Dr. Keith Holland and Dr. David Lawrence of James Madison University (JMU) initiated a research program to investigate materials for the photoelectrochemical decomposition of water into hydrogen and oxygen, …

Generalized Ellipsometry Analysis Of Anisotropic Nanoporous Media: Polymer-Infiltrated Nanocolumnar And Inverse-Column Polymeric Films, Dan Liang

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Characterization of the structural and optical properties is a subject of significance for nanoporous material research. However, it remains a challenge to find non-destructive methods for investigating the anisotropy of porous thin films with three-dimensional nanostructures. In this thesis, a generalized ellipsometry (GE) analysis approach is employed to study two types of anisotropic nanoporous media: slanted columnar thin films (SCTFs) with polymer infiltration and inverse-SCTF polymeric films. The thesis presents the physical properties obtained from GE analysis, including porosity, columnar shape, principal optical constants, birefringence, etc.

The thesis reports on using a GE analysis approach, combining the homogeneous biaxial layer …

Interstitial Silicon Ions In Rutile Tio2 Crystals, Eric M. Golden, Nancy C. Giles, Shan Yang, Larry E. Halliburton

Faculty Publications

Electron paramagnetic resonance (EPR) is used to identify a new and unique photoactive silicon-related point defect in single crystals of rutile TiO₂. The importance of this defect lies in its assignment to interstitial silicon ions and the unexpected establishment of silicon impurities as a major hole trap in TiO₂. Principal g values of this new S=1/2 center are 1.9159, 1.9377, and 1.9668 with principal axes along the [¯110],[001], and [110] directions, respectively. Hyperfine structure in the EPR spectrum shows the unpaired spin interacting equally with two Ti nuclei and unequally with two Si nuclei. These silicon …

Towards The Perfect Optical Fiber, John Ballato

Journal of the South Carolina Academy of Science

Optical fibers are being used in an ever more diverse array of applications today. Many of these modern applications are in high-power and, particularly, high power-per-unit-bandwidth systems where optical nonlinearities historically have not limited overall performance. Today, however, nominally weak effects, such as stimulated Brillouin scattering (SBS), are restricting continued scaling to higher optical powers. To address these limitations, the optical fiber industry has focused on fiber geometry-related solutions such as large mode area (LMA) designs. However, since all linear and nonlinear optical phenomena are fundamentally materials-based in origin, this paper identifies material solutions to present and future performance limitations …

Photoluminescence And Optically Stimulated Luminescence Studies Of Lialo2 And Ligao2 Crystals, Ian P. Ferguson

Theses and Dissertations

Copper diffusion in LiAlO2 creates large photoluminescence (PL) and optically stimulated luminescence (OSL) signals that are not present in as-grown samples. The main PL band peaks at 3.45 eV (359 nm) and is excited by a band peaking at 4.54 eV (273 nm). After x-ray irradiation, OSL results from 425-500 nm continuous wave light. An optical absorption band in the same region decays during optical stimulation. Analysis of the wavelength dependence of the OSL emitted light reveals a band that is similar in peak location and width to the PL band suggesting that they occur at the same copper defect. …

Theoretical Investigation Of Stabilities And Optical Properties Of Si12C12 Clusters, Xiaofeng F. Duan, Larry W. Burggraf

Faculty Publications

By sorting through hundreds of globally stable Si₁₂C₁₂ isomers using a potential surface search and using simulated annealing, we have identified low-energy structures. Unlike isomers knit together by Si–C bonds, the lowest energy isomers have segregated carbon and silicon regions that maximize stronger C–C bonding. Positing that charge separation between the carbon and silicon regions would produce interesting optical absorption in these cluster molecules, we used time-dependent density functional theory to compare the calculated optical properties of four isomers representing structural classes having different types of silicon and carbon segregation regions. Absorptions involving charge transfer between segregated …

3d Printing, Open-Source Technology And Their Applications In Research, Chenlong Zhang

Dissertations, Master's Theses and Master's Reports

Open-source software received tremendous success as it drives down the cost of software and expand the distribution. Open-source hardware, as part of the open-source movement, has just risen into public attention for its potential to further drive down the cost of all kinds of manufacturing goods and reshape the manufacture chain. In this report we explores the history, development and the future of open-source hardware project, summarizing the opportunities, challenges and possible solutions. 3D printing is demonstrated as a booster to assist open-source hardware’s development. Low-cost 3D printer enables at-home and in-time fabrication, the download-print-use-improve-distribute cycle is established to encourage …