Semiconductor and Optical Materials Commons^™

Pulsed Laser Annealing On The Optoelectronic Properties Of Zno Thin Films, Md Abu Zobair

Graduate Theses/Dissertations

ZnO thin films have attracted great attention recently due to their unique electronic and optical properties. However, for proper implementation of ZnO in electronic devices it is necessary to understand the role of native point defects present inside the material as these wide bandgap semiconductors are inherently n-type due to oxygen vacancies. The objective is to control the electronic and optical properties of ZnO thin films through pulsed laser annealing (PLA). Thin films of ZnO have been grown on different substrates using pulsed laser deposition. Then PLA of the films are done by changing laser parameters (energy, frequency, pulse width, …

Investigation And Characterization Of New Optically Stimulated Luminescence (Osl) Dosimetric Materials, Linyu Pan

All Dissertations

Optically stimulated luminescence (OSL) dosimeters have attracted increasing attention due to advantages over TL dosimeters, including no thermal quenching and higher sensitivity. Nevertheless, currently, there are only two commercially available OSL dosimeters, BeO and Al₂O₃:C. An OSL dosimeter requires low effective atomic number (Z_eff < 16), at least one type of recombination center and one type of trap, and UV~blue emission. In this dissertation, motivated by the search of new OSL dosimetric materials, a systematic investigation of alumina (Z_eff = 11.3) and magnesium aluminate spinel (Z_eff = 11.2) based materials was performed in terms of the engineering of the recombination centers and electronic traps. Microstructural characterization was executed by means of X-ray diffraction (XRD) and Raman spectroscopy. Luminescence was characterized under X-ray excitation (radioluminescence; RL) at ambient and …

Interferometric Lithography- An Approach To Large Area And Cost Effective Nanopatterning, Vineeth Sasidharan

Optical Science and Engineering ETDs

In this dissertation interferometric lithography is approached in two different ways to address two important constraints of nanopatterning. One approach solves the problem of scaling up interferometric lithography to wafer scale (4 inch or larger) area. Through the second approach we have developed a nanopatterning technique based on interferometric lithography by using an inexpensive (~$100) diode laser as source, making interferometric lithography a very cost-effective technique.

Wafer-scale large-area nanopatterning was developed using an amplitude grating mask as a grating beam splitter along with spatial averaging of laser intensity by wobbling. The longitudinal and transverse coherence issues both are eased by …

Nanocrystals Impregnated Porous Article And Method Of Making And Using Same, Michael D. Sherburne

AFIT Patents

The present invention relates to devices for detecting radiation by the excitation of colloidal nanocrystals within a porous article and methods of using same. The aforementioned device is inexpensive and can be fabricated quickly in order to detect radiation. Due to the use of colloidal nanocrystals which have been known to have a decay constant of under 100 ps when energetic electrons produced by an incident x-ray excite the nanocrystals, this device can be used in fast radiation detection of x-rays.

Optically Active Selenium Vacancies In Baga4Se7 Crystals, Brian C. Holloway, Timothy D. Gustafson, Christopher A. Lenyk, Nancy C. Giles, Kevin T. Zawilski, Peter G. Schunemann, Kent L. Averett, Larry E. Halliburton

Faculty Publications

Barium gallium selenide (BaGa₄Se₇) is a recently developed nonlinear optical material with a transmission window extending from 470 nm to 17 μm. A primary application of these crystals is the production of tunable mid-infrared laser beams via optical parametric oscillation. Unintentional point defects, such as selenium vacancies, cation vacancies (barium and/or gallium), and trace amounts of transition-metal ions, are present in BaGa₄Se₇ crystals and may adversely affect device performance. Electron paramagnetic resonance (EPR) and optical absorption are used to identify and characterize these defects. Five distinct EPR spectra, each representing an electron …

Method Of Making Temperature-Immune Self-Referencing Fabry–Pérot Cavity Sensors, Hengky Chandrahalim, Jonathan W. Smith

AFIT Patents

A method of making passive microscopic Fabry-Pérot Interferometer (FPI) sensor includes forming a three-dimensional microscopic optical structure on a cleaved tip of an optical fiber that reflects a light signal back through the optical fiber. The reflected light is altered by refractive index changes in the three-dimensional structure that is subject to at least one of: (i) thermal radiation; and (ii) volatile organic compounds.

Perovskite Film Formation For Solar Cell Absorbers: Effects Of Substrate Modification, Mirra M. Rasmussen, Kyle M. Crowley, Ina T. Martin

Student Scholarship

As perovskite solar cell efficiencies have risen rapidly, practical constraints have made durability a critical concern. Whereas much attention has been paid to the development of the perovskite absorber layer, the charge transport layers can also be engineered to better the performance and stability of the device. This work uses the molecular modifier bromopropyltrimethoxysilane (BPTMS) to alter the interface between indium tin oxide (ITO, a common thin film solar cell transparent electrode) and methylammonium lead iodide (MAPbI3, a common perovskite absorber) to improve the morphology and stability of the perovskite absorber film. The substrate, molecular modifier, and perovskite film were …

Engineering The Surface Of Fe3o4 Nanoparticles For Catalytic And Magnetic Applications, Natalia Da Silva Moura

LSU Doctoral Dissertations

With the rapid depletion of the U.S. energy resources coupled with population growth, heat management technologies must be improved to sustain our quality of life. Precisely, in catalysis, it is estimated that only ~50% of the energy supplied to the reactor is used for product conversion due to dissipation losses. Among the emerging technologies with a promising reduction in heat losses is induction heating, offering targeted heat delivery with magnetic nanoparticles. Under alternating magnetic fields (AMF), these nanoparticles can absorb the energy from Radio-Frequency (RF) fields and dissipate it as heat on the nanoparticle surface. This in situ heat generation …

Rapid Annealing Of Perovskite Solar Cell Thin Film Materials Through Intense Pulse Light., Amir Hossein Ghahremani

Electronic Theses and Dissertations

Perovskite solar cells (PSCs) have garnered a great attention due to their rapid efficiency improvement using cheap and solution processable materials that can be adapted for scalable high-speed automated manufacturing. Thin film perovskite photovoltaics (PVs) are typically fabricated in an inert environment, such as nitrogen glovebox, through a set of deposition and annealing steps, each playing a significant role on the power conversion efficiency (PCE), reproducibility, and stability of devices. However, atmospheric processing of PSCs would achieve lucrative commercialization. Therefore, it is necessary to utilize materials and methods that enable successful fabrication of efficient PSCs in the ambient environment. The …

Numerical Calculation Of Losses Of Trapped Vortices Under Strong Rf Meissner Current And Dc Superheating Field In Type Ii Superconductors, Walive Pathiranage Manula Randhika Pathirana

Physics Theses & Dissertations

Research on the vortex dynamics and enhancing of superheating field in superconductors has attracted much attention in accelerator physics community to develop next-generation high-performance accelerator cavities. However, the extreme dynamics of curvilinear elastic vortices driven by very strong currents close to the depairing limit or superheating field of a superconductor with a nanostructured surface has not been well understood. We calculated the superheating field H_sh and critical momentum kc characterizing the wavelength of the instability λ_m of the Meissner state to flux penetration by solving numerically the Ginzburg-Landau equations. A bulk superconductor, superconductor with the inhomogeneous surface disorder …

Surface Energy And Microstructure: The Effect Of The Underlying Substrate On Perovskite Film Formation For Solar Cell Absorbers, Mirra M. Rasmussen, Kyle M. Crowley, Ina T. Martin

Student Scholarship

No abstract provided.

Fabrication And Characterization Of Photodetector Devices Based On Nanostructured Materials: Graphene And Colloidal Nanocrystals, Wafaa Gebril

Graduate Theses and Dissertations

Photodetectors are devices that capture light signals and convert them into electrical signals. High performance photodetectors are in demand in a variety of applications, such as optical communication, security, and environmental monitoring. Among many appealing nanomaterials for novel photodetection devices, graphene and semiconductor colloidal nanocrystals are promising candidates because of their desirable and unique properties compared to conventional materials.

Photodetector devices based on different types of nanostructured materials including graphene and colloidal nanocrystals were investigated. First, graphene layers were mechanically exfoliated and characterized for device fabrication. Self-powered few layers graphene phototransistors were studied. At zero drain voltage bias and room …

Distributed Modeling Approach For Electrical And Thermal Analysis Of High-Frequency Transistors, Amirreza Ghadimi Avval

Graduate Theses and Dissertations

The research conducted in this dissertation is focused on developing modeling approaches for analyzing high-frequency transistors and present solutions for optimizing the device output power and gain. First, a literature review of different transistor types utilized in high-frequency regions is conducted and gallium nitride high electron mobility transistor is identified as the promising device for these bands. Different structural configurations and operating modes of these transistors are explained, and their applications are discussed. Equivalent circuit models and physics-based models are also introduced and their limitations for analyzing the small-signal and large-signal behavior of these devices are explained. Next, a model …

Direct Torque Control For Silicon Carbide Motor Drives, Mohammad Hazzaz Mahmud

Graduate Theses and Dissertations

Direct torque control (DTC) is an extensively used control method for motor drives due to its unique advantages, e.g., the fast dynamic response and the robustness against motor parameters variations, uncertainties, and external disturbances. Using higher switching frequency is generally required by DTC to reduce the torque ripples and decrease stator current total harmonic distortion (THD), which however can lower the drive efficiency. Through the use of the emerging silicon carbide (SiC) devices, which have lower switching losses compared to their silicon counterparts, it is feasible to achieve high efficiency and low torque ripple simultaneously for DTC drives.

To overcome …

Decoupling The Effects Of Interfacial Chemistry And Grain Size In Perovskite Stability, Mirra M. Rasmussen, Kyle M. Crowley, Miranda S. Gottlieb, Geneviève Sauvé, Ina T. Martin

Student Scholarship

No abstract provided.

Research And Application Of Copper Electroplating In Interconnection Of Printed Circuit Board, Chong Wang, Chuan Peng, Jing Xiang, Yuan-Ming Chen, Wei He, Xin-Hong Su, Yu-Yao Luo

Journal of Electrochemistry

Copper electroplating is the key technology for manufacturing of integrated circuit, packaging substrate, printed circuit board, and other electronic interconnection components. However, the electrochemistry and mechanism of deposition growth have not been fully elucidated, and the development of additives and bath maintenance are inseparable from a large number of experiments. This article reviews recent fundamental research and application progress in copper electroplating for printed circuit board industry, and these works are mainly dedicated by the research group of Printed Circuit and Printed Electronics from University of Electronic Science and Technology of China. First of all, a brief history of copper …

Design And Fabrication Of Zinc Oxide Optofluidic Laser Elements, Kyle T. Bodily

Theses and Dissertations

This thesis systematically goes through the derivation, simulation, and experimentation of Zinc Oxide optofluidic micro laser elements. Single and coupled ring resonators were simulated to show single mode transmission as well as enhanced coupling capabilities when surrounded by high refractive index liquid. Devices with diameters ranging from 100-500 µm were successfully fabricated inexpensively through standard cleanroom procedures. The devices were tested using two different pump laser systems. Testing included such factors as high pump intensity, various angles of excitation, and low temperature. In all cases PL emission was observed and recorded.

Experimental Investigation Of Surface Resistivity Of Yttrium Stabilized Zirconium As A Thin Film, Matthew J. Melfi

Seton Hall University Dissertations and Theses (ETDs)

Solid Oxide Fuel Cells are devices that use electrochemical reactions to convert chemical energy from fuel to electricity. In comparison with coal power plants, a Solid Oxide Fuel Cell, produces a higher electrical conversion efficiency. However, at higher temperatures (1000°C) it creates a lower ionic conductivity, which limit the Solid Oxide Fuel Cells. When lowering the temperature, the ohmic resistance increases. In our research, an Yttrium Stabilized Zirconium layer will be produced from a fine dimple grain structure allowing high flow of oxygen mobility. This mobility increases ionic conductivity and decrease ohmic loss. The goal of our research is first …

Characterization Of Gesn Semiconductors For Optoelectronic Devices, Hryhorii Stanchu

Graduate Theses and Dissertations

Germanium-tin alloys with Sn compositions higher than 8 at. % to 10 at. % have recently attracted significant interest as a group IV semiconductor that is ideal for active photonics on a Si substrate. The interest is due to the fact that while at a few percent of Sn, GeSn is an indirect bandgap semiconductor, at about 8 to 10 at. % Sn, GeSn transitions to a direct bandgap semiconductor. This is at first surprising since the solid solubility of Sn in Ge under equilibrium growth conditions is limited to only about 1 at. %. However, under non-equilibrium growth conditions, …

Si-Based Germanium Tin Photodetectors For Infrared Imaging And High-Speed Detection, Huong Tran

Graduate Theses and Dissertations

Infrared (IR) radiation spans the wavelengths of the windows: (1) near-IR region ranging from 0.8 to 1.0 μm, (2) shortwave IR (SWIR) ranging from 1.0 to 3.0 μm, (3) mid-wave IR (MWIR) region covering from 3.0 to 5.0 μm, (4) longwave IR (LWIR) spanning from 8.0 to 12.0 μm, and (5) very longwave IR extending beyond 12.0 μm. The MWIR and LWIR regions are important for night vision in the military, and since the atmosphere does not absorb at these wavelengths, they are also used for free-space communications and astronomy. Automotive and defect detection in the food industry and electronic …