Polymer and Organic Materials Commons^™

Wear Resistant Polydopamine/Ptfe Nanoparticle Composite Coating For Dry Lubrication Applications, Samuel George Beckford

Graduate Theses and Dissertations

This dissertation presents an investigation into the effect of nanoparticle fillers and a polydopamine adhesive primer on the tribological performance of thin PTFE films. The principal objective of this investigation was to reduce wear in PTFE films, an issue which precludes the use of PTFE films in tribological applications requiring high durability. The friction and wear of the composite films were evaluated using a ball-on-flat configuration in linear reciprocating motion. It was found that the use of a polydopamine adhesive primer reduces the wear of PTFE films more than 600 times. X-ray photoelectron spectroscopy (XPS) results show that a tenacious …

Metal Assisted Nanowire Growth For Silicon Nanowire/Amorphous Silicon Composite Solar Cell, Asmaa Ali Sadoon

Graduate Theses and Dissertations

Solar cells are photovoltaic devices that convert the energy of light to electricity by the photovoltaic effect. Crystalline silicon-based solar cells are the most dominant solar cells in the market today due to the high efficiency and relatively low cost. However, the cost of such solar cell is still high due to the large amount of material that is consumed in fabricating such a device. Polycrystalline/amorphous thin films and nanomaterial technologies have emerged to reduce the high cost of c-Si based solar cells and increase the efficiency. In this research, we combined these two technologies to propose and fabricate silicon …

Growth And Properties Of Carbon Microcoils And Nanocoils, Muneaki Hikita, Robyn Bradford, Khalid Lafdi

Chemical and Materials Engineering Faculty Publications

Various types of coiled carbon filaments have been synthesized using chemical vapor deposition and other methods. These carbon filaments exhibit unique electrical and mechanical properties due to their versatile shapes and structures. To form coiled shapes, different types of catalyst compositions and reactive gases have been explored. Generally, coiled carbon filaments are classified by coil diameter and shape (e.g., microcoil and nanocoil). In this review, coiled carbon filaments are classified into three growth mechanism categories:

(1) bidirectional double helical growth;

(2) bidirectional twisted growth; and

(3) tip single helical or twisted growth.

Next, their synthesis methods and hypothetical growth mechanisms …

Slow Release Of Ions From Internalized Silver Nanoparticles Modifies The Epidermal Growth Factor Signaling Response, Kristen K. Comfort, Elizabeth I. Maurer, Saber M. Hussain

Chemical and Materials Engineering Faculty Publications

Due to their distinctive physiochemical properties, including a robust antibacterial activity and plasmonic capability, hundreds of consumer and medical products contain colloidal silver nanoparticles (AgNPs). However, even at sub-toxic dosages, AgNPs are able to disrupt cell functionality, through a yet unknown mechanism. Moreover, internalized AgNPs have the potential to prolong this disruption, even after the removal of excess particles. In the present study, we evaluated the impact, mechanism of action, and continual effects of 50 nm AgNP exposure on epidermal growth factor (EGF) signal transduction within a human keratinocyte (HaCaT) cell line. After AgNP expose, EGF signaling was initially obstructed …

Effect Of Plasticizer On Oxygen Permeability Of Cast Polylactic Acid (Pla) Films Determined Using Dynamic Accumulation Method, Kurniawan Yuniarto, Bruce A. Welt, Aris Purwanto, Hadi Karia Purwadaria, Ayman Abdellatief, Titi C. Sunarti, Setyo Purwanto

Journal of Applied Packaging Research

Polylactic acid (PLA) is becoming an increasingly important biopolymer for packaging applications. PLA brittleness limits its applicability. This study evaluated PLA properties with increasing amounts of added polyethylene glycol (PEG) plasticizer. Oxygen transmission rate (OTR) of cast films was determined using the newly available Dynamic Accumulation (DA) method. Arrhenius temperature sensitivity of OTR and polymer Permeability was also determined. Permeability of neat PLA is 4.848 ml mm (STP)/m² s kPa; hence, 4.84 ml mm (STP)/m² s kPa, 4.07 ml mm (STP)/m² s kPa and 5.42 ml mm (STP)/m² s kPa by adding PEG 1 %, 5% …

Simulation Studies Of Organic Solar Cell Structure And Morphology On The Device Efficiency, Satish Kumar Reddy Kota

Electrical & Computer Engineering Theses & Dissertations

Solar cells based on organic materials offer several advantages over the traditional solar cells made with inorganic materials. These include a lower impact on nature, smaller weight, the avoidance of cleanrooms for their production, their flexibility which makes it possible to wrap or coat them on objects with varying shapes and geometries, and most significantly their ability to produce electricity in diffuse'd light which is a distinct advantage over conventional solar cells. Organic solar cells have their own disadvantage of very low efficiencies as compared to inorganic solar cells. The morphology and structure of the organic solar cells plays a …

Humic Substances-Based Polymer System, Gerard R. Thiel

Patents (University of Northern Iowa)

A system for use in forming polymer compositions, including as a replacement for phenolic based resin systems, for instance, in preparing foundry molds. In a preferred embodiment, the system includes the use of a) a polyermizable hydroxyl-containing component comprising a humic substance (as can be provided by lignite), b) an isocyanate component, and c) a catalyst, and preferably amine catalyst, component adapted to catalyze the polymerization of a) and b). The system is optionally used as binder system in the presence of a filler, such as, in combination with a foundry aggregate such as sand. A polymer system of this …

Polymer-Based Thermoelectric Devices, Stuart W. Hilsmier, Edward P. Tomlinson, Bryan Boudouris

The Summer Undergraduate Research Fellowship (SURF) Symposium

Currently, over 50% of all energy generated in the US is lost as waste heat, and thermoelectric generators offer a promising means to recoup some of this energy, if their efficiency is improved. While organic thermoelectric materials lack the efficiency of their inorganic counterparts, they are composed of highly abundant resources and have low temperature processing conditions. Recently, a new class of redox-active polymers, radical polymers, has exhibited high electrical conductivity in an entirely amorphous medium. In addition, these radical polymers have a simple synthetic scheme and can be highly tunable to provide desired electrical properties. In this study, the …

Characterization Of Mechanical Properties Displayed In Body Armor Ballistic Fibers, Dawei Li, Matthew Hudspeth, Weinong Wayne Chen

The Summer Undergraduate Research Fellowship (SURF) Symposium

The current body armor systems manufactured using ballistic fibers are not performing as theoretical results predict and are causing injuries. The actual maximum projectile penetration speed that the body armor can endure is significantly lower than the theoretical maximum speed, thus causing a costly build-test relationship that is not aided with modeling design efforts. The main aim of this research is to determine the maximum penetration speeds for ballistic yarns and fabrics. Secondary aim is to examine the common assumption that during transverse impact, single fiber is under pure tension and shear stress is negligible. To examine aforementioned assumption, fibers …

Simulation Of Bio-Inspired Porous Battery Separators, Yumeng Xie, Edwin Garcia, Aniruddha Jana

The Summer Undergraduate Research Fellowship (SURF) Symposium

Li-Ion rechargeable battery is one of the most-used rechargeable batteries around the industry of the world. The battery is most used in most electronic devices, electrical cars. But the battery separator is one of the mainly problem that limits the service life. If we can find the way to improve the performance of the battery separator, we can highly increase the service life of the Li-Ion battery. The goal of the project 'Simulation of Bio-Inspired Porous Battery Separators' is to generate a tool for users in order to create computer models of bio-inspired porous structures that resemble porous separators layer …

Rheo-Piv Investigation Of Fracture And Self-Healing In A Triblock Copolymer Gel, Benjamin A. Helfrecht, Travis L. Thornell, Kendra A. Erk

The Summer Undergraduate Research Fellowship (SURF) Symposium

Physically associating polymer gels have shown the ability to heal after failure, making them promising candidates for various medical applications or consumer products. However, the processes by which these materials self-heal is not well-understood. This study seeks to explain the self-healing behavior of the triblock copolymer poly(methyl methacrylate)-poly(n-butyl acrylate)-poly(methyl methacrylate), or PMMA-PnBA-PMMA, by probing the material’s post-fracture behavior with rheometry and particle image velocimetry (PIV). The self-healing behavior was studied by deforming each gel in shear until failure multiple times with “recovery” periods in-between. PIV was used to verify the occurrence of each fracture in both time and space. Stress …

Investigation Of Fracture And Healing Behavior Of Thermoreversible Gels Via Oscillation Rheology, Krithika Subramaniam, Travis Thornell, Kendra Erk

The Summer Undergraduate Research Fellowship (SURF) Symposium

Thermoreversible gels have the unique ability to self-heal, or repair themselves, once they are fractured. They are physically cross-linked, thus providing them with the capability to reform their broken bonds as a function of temperature. The objective of this project is to determine the extent of the gels’ recovery. If self-healing does in fact occur, these gels can be applied in various industries, including medicine for drug delivery or paints and coatings. The tri-block polymer poly(methyl methacrylate)-poly(n-butyl acrylate)-poly(methyl methacrylate) (PMMA-PnBA-PMMA) was heated and stirred with 2-ethyl-1-hexanol to create a polymer gel. Through the use of a rheometer, a shear stress …

Interfacial Interactions Between Carbon Nanoparticles And Conjugated Polymers, Yanqi Luo

Master's Theses

Conjugated polymer based electronics, a type of flexible electronic devices, can be produced from solution by traditional printing and coating processes in a roll-to-roll format such as papers and graphic films. This shows great promise for the emerging energy generation and conversion. The device performance of polymer electronics is largely dependent of crystalline structures and morphology of photoactive layers. However, the solution crystallization kinetics of conjugated polymers in the presence of electron acceptor nanoparticles has not been fully understood yet. In this study, solution crystallization kinetics of poly (3-hexylthiophene) in the presence of carbon nanotubes and graphene oxide has been …

Photo-Sensitivity Of Large Area Physical Vapor Deposited Mono And Bilayer Mos2, Baoming Wang, Christopher Muratore, Andrey A. Voevodin, M. Amanul Haque

Chemical and Materials Engineering Faculty Publications

We present photosensitivity in large area physical vapour deposited mono and bi-layer MoS2 films. Photo-voltaic effect was observed in single layer MoS2 without any apparent rectifying junctions, making device fabrication straightforward. For bi-layers, no such effect was present, suggesting strong size effect in light-matter interaction. The photo-voltaic effect was observed to highly direction dependent in the film plane, which suggests that the oblique deposition configuration plays a key role in developing the rectifying potential gradient. To the best of our knowledge, this is the first report of any large area and transfer free MoS2 photo device with performance comparable to …

A Soft Condensed Matter Approach Towards Mathematical Modelling Of Mass Transport And Swelling In Food Grains, Michael Chapwanya, N. Misra

Articles

Soft condensed matter (SCM) physics has recently gained importance for a large class of engineering materials. The treatment of food materials from a soft matter perspective, however, is only at the surface and is gaining importance for understanding the complex phenomena and structure of foods. In this work, we present a theoretical treatment of navy beans from a SCM perspective to describe the hydration kinetics. We solve the transport equations within a porous matrix and employ the Flory–Huggin’s equation for polymer–solvent mixture to balance the osmotic pressure. The swelling of the legume seed is modelled as a moving boundary with …

Synthesis And Characterization Of Cdse/Zns Core/Shell Quantum Dot Sensitized Pcpdtbt-P3ht:Pcbm Organic Photovoltaics, Buddy J. Bump

Master's Theses

Durable, cheap, and lightweight polymer based solar cells are needed, if simply to meet the demand for decentralized electrical power production in traditionally “off-grid” areas. Using a blend of Poly(3-hexylthiophene-2,5-diyl) (P3HT), Phenyl-C61-butyric acid methyl ester (PCBM), and the low band-gap polymer Poly[2,6-(4,4-bis-(2- ethylhexyl)-4H-cyclopenta [2,1-b;3,4-b′]dithiophene)-alt-4,7(2,1,3-benzothiadiazole)] (PCPDTBT), we have fabricated devices with a wide spectral response and 3% power conversion efficiency in AM 1.5 conditions; however, this thin film system exhibits only 0.43 optical density at 500 nm. To improve the performance of this polymer blend photovoltaic, we aim to increase absorption by adding CdSe(ZnS) core (shell) quantum dots. Four groups of …

Manufacture And Mechanical Testing Of Thin Film Composites Composed Of Poly-Lactic Acid And Nanocrystalline Cellulose, Catherine E. Mohan

Materials Engineering

Society’s overuse of petroleum-based plastic products has created a waste problem that is threatening environments around the world. New efforts have been made to find a suitable replacement derived from a renewable source. Poly-lactic acid has become one of the front-runners in this search. It is derived from starches found in potatoes, corn, and other grains. There are many factors that make Poly-lactic acid-based polymers a suitable replacement for petroleum-based ones, but it still suffers from low mechanical strength due to low crystallinity percentages. Doping the polymer with nanocrystalline cellulose provides more nucleation sites for the crystallization of the polymer …

Mechanical Behavior Of Compression Molded Polyethylene Terephthalate, Daniel Cole Greinke, Paul Jackson Mcewan, Dan Tran

Materials Engineering

The purpose of this project was to investigate the effects of time, temperature, and pressure on the tensile strength and elastic modulus of recycled PET. Compression molding trials were performed on shredded PET bottles to produce tensile test specimens conforming to ASTM D638-03. Aluminum molds containing the PET were mechanically fastened together at the desired pressure and heated in an electric oven. The resulting specimens were subjected to tensile testing for analysis. This screening experiment failed to generate any statistically significant data concerning the factors of interest. These preliminary results may be used to design a more systematic follow-up study.

Prediction Of Tribological Behavior Of Candidate Materials For Rotor Seals, John W. Franzino, Will F. Michul

Materials Engineering

To reduce high costs associated with manufacturing and testing materials for rotor seals, a procedure needs to be developed to quickly and accurately test candidate materials as they are released. The test should reduce the amount of fabrication required and model working conditions in order to accurately assess the tribological behavior of candidate materials. A possible solution was examined that utilized a rig meant to model operational stresses and wear. Compression modulus data was then taken in order to quantify the accumulation of damage due to microcracking, the primary mode of failure, through a damage index parameter. Testing results concluded …

Characterization Of A Thin Film Composite Membrane: Fluorinated Copolymer In A Carbon Nanotube Matrix, Eric P. Bonaventure, Michael A. Brew, Cynthia R. Shannon

Materials Engineering

IDEX Health and Science has created a thin-film composite membrane consisting of a carbon nanotube matrix impregnated with a fluorinated copolymer called Teflon® AF 2400. This membrane is being studied for use in degassing chambers of analytical instruments such as a High Pressure Liquid Chromatography (HPLC) degassing modules. The level of impregnation of the Teflon® in the carbon matrix affects the diffusion properties which are crucial for the performance of the membrane. Scanning Electron Microscopy (SEM) characterization techniques were used to measure the outer Teflon® and the inner carbon matrix layer thickness. The outer Teflon® and inner carbon matrix layer …