Polymer and Organic Materials Commons^™

Nano-Enhanced Composite Membranes For Water Desalination, Benjamin Fredrik Victor Sundling Von Fürstenrecht

Materials Engineering

In theory single walled carbon nanotubes (SWCNT) will aid in ion rejection due hydrophobicity and smoothness of the SWCNT. An efficient means of water desalination utilizing SWCNT in a membrane seems plausible. A lyotropic liquid crystal (LLC) solution was made with a synthesized polymerizable surfactant methacryloxy ethyl hexadecyl dimethyl ammonium bromide (C16MA) to help with vertical alignment of SWCNT. Due to SWCNT lack of solubility and tendency to agglomerate in water, a dispersion performed using an inert surfactant centrimonium bromide (CTAB) to make sure that the SWCNT were homogeneously dispersed in the solution without altering the hexagonal packing factor of …

Effects Of Heat Treatment On The Dimensional Stability And Mechanical Properties Of Guadua Bamboo, Kade Schmitz, Skye Dascher, Shalto Dascher

Materials Engineering

Contributing to about 4% of particulate emissions, the construction industry is one of the largest polluters of the environment. In an effort to reduce emissions, BamCore has produced a dual panel wall system made of Guadua bamboo with a Douglas fir veneer. Bamboo is a highly renewable material with a fast growth rate and carbon sequestration abilities. This project investigates how heat treating Guadua bamboo influences its dimensional changes and mechanical properties for building applications. It was found that a dimensional increase in every direction occurred for all samples when exposed to higher relative humidity (50% to 90%), and that …

Minimizing The Dimensional Change In Two Component Epoxy Based Thermoset Adhesives Through Adapting Mix Ratio And Initial Crosslink Density, Jefferson Peter Norman

Materials Engineering

Meissner Filtration uses amine-hardened epoxy as a high-performance adhesive to encapsulate hollow fiber membranes at the ends of rigid filter housings. Dimensional change of the epoxy while curing can result in residual stress formation that is detrimental to the manufacturing of the filter and causes structural integrity issues when the filter is used in industrial processes where heating and cooling cycles are implemented. The residual stresses can cause cracks, microscopic fractures, and delamination from the housing, resulting in failure of the filter. The goal of this project was to evaluate how changes in processing conditions could minimize dimensional variability due …

Non-Toxic Soil Thickeners For Reducing Mudslide Intensity, Miranda Miao, Isaac Blackburn, Erika Haley Yao

Materials Engineering

Non-toxic food thickeners were investigated as a solution for thickening mud to mitigate the effects of mudslides. All soil was obtained from a site on the California Polytechnic State University campus where a mudslide occurred in 2017. Guar gum was mixed into the soil at 1 wt% and 10 wt% of the moisture content in the soil. Whey protein was mixed into the soil at 2 wt% and 19 wt% of the moisture content in the soil. The soils’ liquid limit was found using the Casagrande cup testing method. Liquid limit testing indicated that thickeners raised the liquid limit, most …

Maximizing Poly(3-Butylthiophene-2,5-Diyl) Electrical Conductivity By Maximizing Transcrystal Growth, Edward Alexander Bicknell

Materials Engineering

Polymers are generally considered electrical insulators. Despite this, research in the mid 1970’s found that polymers consisting of a conjugated backbone structure could become electrically conductive upon doping.1 The conjugated polymer analyzed for this project was poly(3-butylthiophene-2,5-diyl) (P3BT). Transcrystals have been found as a way to promote electrical conductivity through mechanisms including π bond atomic orbital overlap and electron mobility.2 In theory, maximizing transcrystal length would also maximize P3BT electrical conductivity, increasing its applicable use in electronic devices. The goal of this project was to determine a methodological way to maximize P3BT electrical conductivity by producing the longest transcrystal length …

Photooxidation Of Biopolymers, Marlon H. Dieguez

Materials Engineering

The lack of degradation of plastic products have imposed problems in the preservation of natural environments and their ecosystems through plastic accumulation. This collection of plastics promotes toxin exposure to wildlife, finding its way into the food chain, affecting both land and marine ecosystems. The project goal is to understand the degradation mechanisms of biodegradable materials and other comparable materials through UV radiation testing. Polylactide (PLA) films and polycarbonate (PC) films will be compared for their relative deterioration from constant UV radiation in a Q-U-V accelerated weather tester for 28 days. Five 3” by 5” samples of 14 mil thick …

Nano Fab Lab 63, Brian K. Deemer, Josh Clemons, Nick Brodine, Delaney Fitzsimmons

Mechanical Engineering

Lawrence Livermore National Laboratories (LLNL) has several steps in the production process for ceramic nanofiber tubes that they would like to improve - electrospinning, cutting, rolling, sealing and heat treating. We undertook the challenge to deliver LLNL with a semi-automated process that efficiently integrates the steps of cutting, rolling, and sealing to save time and improve control over end dimensions. In this document, we discuss the technical background of the manufacturing steps currently followed to create nanofiber tubes, identify which steps are incorporated in our prototype and explain how they will interface with one another, define the design requirements, present …

Triperyleno[3,3,3]Propellane Triimides: Achieving A New Generation Of Quasi-D3h Symmetric Nanostructures In Organic Electronics, Lingling Lv, Josiah Roberts, Chengyi Xiao, Zhenmei Jia, Wei Jiang, Chad Risko, Lei Zhang

Chemistry Faculty Publications

Rigid three-dimensional (3D) polycyclic aromatic hydrocarbons (PAHs), in particular 3D nanographenes, have garnered interest due to their potential use in semiconductor applications and as models to study through-bond and through-space electronic interactions. Herein we report the development of a novel 3D-symmetric rylene imide building block, triperyleno[3,3,3]propellane triimides (6), that possesses three perylene monoimide subunits fused on a propellane. This building block shows several promising characteristics, including high solubility, large π-surfaces, electron-accepting capabilities, and a variety of reactive sites. Further, the building block is compatible with different reactions to readily yield quasi-D_3h symmetric nanostructures (9, …

Novel Low Shear 3d Bioreactor For The Scaled Production Of High Purity Human Mesenchymal Stem Cells, Andrew Burns

KGI Theses and Dissertations

Human mesenchymal stem cells are an ideal candidate for stem cell therapies. They have been researched since the 1960’s and can differentiate into many desired functional cell types without undergoing teratogenesis. However, higher yields are needed for a marketable, successful stem cell therapy. To accomplish this, cells will have to be cultured to expand them to therapeutically relevant dosages for multiple patients. Bioreactor production is an ideal method to solve this problem.

The aim of this thesis is to test and validate a novel bioreactor for the cultivation of human mesenchymal stem cells. In this work, we investigate a novel …

Design And Control Of Fiber Encapsulation Additive Manufacturing, Matt Saari

Mechanical Engineering Research Theses and Dissertations

This work presents the design, development, and analysis of the Fiber Encapsulation Additive Manufacturing (FEAM) system developed at the Laboratory for Additive Manufacturing Robotics \& Automation at the Lyle School of Engineering at Southern Methodist University. The innovation introduced by FEAM is the ability to insert a continuous fiber of different material into the flowing extrudate. Correctly positioning the fiber feed inside the extrudate while turning the fiber in arbitrary directions is a critical aspect of the technology. This will allow for the full exploitation of the capabilities of the FEAM technology to produce robotic components that actuate and sense. …

A Model-Based Framework For The Smart Manufacturing Of Polymers, Santiago D. Salas Ortiz

LSU Doctoral Dissertations

It is hard to point a daily activity in which polymeric materials or plastics are not involved. The synthesis of polymers occurs by reacting small molecules together to form, under certain conditions, long molecules. In polymer synthesis, it is mandatory to assure uniformity between batches, high-quality of end-products, efficiency, minimum environmental impact, and safety. It remains as a major challenge the establishment of operational conditions capable of achieving all objectives together. In this dissertation, different model-centric strategies are combined, assessed, and tested for two polymerization systems.

The first system is the synthesis of polyacrylamide in aqueous solution using potassium persulfate …

Highly Flame-Retardant Rigid Polyurethane Foams Prepared Using Corn Oil, Camila Muliterno Zequine

Electronic Theses & Dissertations

One of the biggest catastrophic problems worldwide is the structural fire that destroys properties, durable goods and lives. Polyurethanes are one of the most important polymers because of the widely use in industrial applications, such as thermal insulation, coating, construction and automobiles. However, polyurethane foams have the disadvantage of being flammable. Most of the starting materials for the production of polyurethanes are derivate from petroleum-based resources, which generates environmental and governmental problems. In this study, bio-based rigid polyurethane foams were synthesized using corn oil. First, commercial corn oil was fully epoxidized to be used in the synthesis of flame-retardant rigid …

Synthesis And Characterization Of Corn Oil Based Polyol And Its Application For Rigid Flame Retardant Polyurethane Foams, Sneha Ramanujam

Electronic Theses & Dissertations

A novel bio-based polyol was synthesized using corn oil and 2-mercaptoethanol via thiol-ene reaction as an alternative to petroleum-based polyol for the synthesis of polyurethane foams. The polyol was analyzed using wet chemical techniques to obtain a hydroxyl number and the viscosity of the polyol. Infrared spectroscopy and gel permeation chromatography were used to confirm the structural properties of the foams. Flame-retardant polyurethane foams were prepared by the addition of different concentrations of dimethyl methyl phosphonate (DMMP) in the final foam composition. The effect of DMMP on the thermo-mechanical properties of the polyurethane foams was analyzed. The TGA analysis showed …

Development Of A Sonically Powered Biodegradable Nanogenerator For Bone Regeneration, Avi S. Patel

University Scholar Projects

Background: Reconstruction of bone fractures and defects remains a big challenge in orthopedic surgery. While regenerative engineering has advanced the field greatly using a combination of biomaterial scaffolds and stem cells, one matter of difficulty is inducing osteogenesis in these cells. Recent works have shown electricity’s ability to promote osteogenesis in stem cell lines when seeded in bone scaffolds; however, typical electrical stimulators are either (a) externally housed and require overcomplex percutaneous wires be connected to the implanted scaffold or (b) implanted non-degradable devices which contain toxic batteries and require invasive removal surgeries.

Objective: Here, we establish a biodegradable, piezoelectric …

Development Of A Sonically Powered Biodegradable Nanogenerator For Bone Regeneration, Avi Patel

Honors Scholar Theses

Background: Reconstruction of bone fractures and defects remains a big challenge in orthopedic surgery. While regenerative engineering has advanced the field greatly using a combination of biomaterial scaffolds and stem cells, one matter of difficulty is inducing osteogenesis in these cells. Recent works have shown electricity’s ability to promote osteogenesis in stem cell lines when seeded in bone scaffolds; however, typical electrical stimulators are either (a) externally housed and require overcomplex percutaneous wires be connected to the implanted scaffold or (b) implanted non-degradable devices which contain toxic batteries and require invasive removal surgeries.

Objective: Here, we establish a biodegradable, piezoelectric …

“Polysoaps” Via Raft Copolymerization To Form Well-Defined Micelles For Water Remediation And Targeted Drug Delivery Applications, Phillip Pickett

Dissertations

Amphiphilic copolymers have become increasingly important for environmental and biological applications due to their behavioral characteristics in aqueous solution. For example, structurally-tailored statistical amphiphilic copolymers or “polysoaps” can self-assemble into micelles or other architectures in water at various concentrations. Polysoaps may be differentiated from small molecule surfactant micelles in their capability to self-assemble into unimolecular associates (unimolecular micelles) with no dependence on concentration. Such micelles offer enormous potential for dispersion of hydrophobic species in water at high dilution. Importantly, each polymer chain forms its own micelle and upon dilution, these micelles remain intact and capable of dispersing hydrocarbon material in …

Engineering Multifunctional And Morphologically Diverse Polymer Brush Surfaces, Cassandra M. Reese

Dissertations

The combination of surface-initiated polymerization (SIP) and post-polymerization (PPM) serves as a powerful approach to fabricate complex, multifunctional polymer films, which can be precisely tuned for desired surface engineering applications. Careful manipulation of PPM parameters such as reaction conditions, the tethered brush parameters, and the physical properties of the unbound post-modifier greatly influence the depth of penetration of the post-modifier and the polymer brush compositional heterogeneity. This dissertation focuses on engineering polymer brush surfaces with multifunctional chemistries and tunable morphologies by investigating the PPM parameters that dictate the distribution of post-modifiers on grafted polymer brush surfaces.

The first chapter of …

Silicone Tadpole: Research Into Soft Bodies, Danielle Fernandez

Mechanical Engineering Undergraduate Honors Theses

In this thesis, research is conducted in the area of soft robotics by building a soft tadpole that can deform with a specific air pressure. The goal is to mimic the motion of an organic tadpole in respect to its S-shaped tail movement. The angle of deformation, derived from material mechanic theories, ranges from 45 to 80 degrees for this type of movement. The design includes a head compartment which acts as a tank to transfer nitrogen pressure and a tail section that receives the said pressure and bends as a result. The tail section was designed with two rows …

Development Of A Multi-Probe Kelvin Scanner Device For Industrially-Relevant Characterization Of Surface-Activated Carbon Fiber Reinforced Thermoplastic Composites, Kirby Simon

McKelvey School of Engineering Graduate Student Theses & Dissertations

Carbon fiber reinforced thermoplastic (CFRTP) composites are becoming increasingly attractive materials in manufacturing due to their lightweight nature, mechanical strength, and corrosion resistance. Surface activation of these materials is usually required during processing to increase the bond strength of assemblies (aerospace and automotive industries) or improve adhesion with implants (biomedical industry). Industrially-relevant, nondestructive quality control methods for assessing the activation state of these materials do not currently exist, however. Applying principles discovered through the use of scanning probe microscopy, a multiple-probe Kelvin scanning (MPKS) device has been developed that can assess the uniformity of the activation state of plasma-treated CFRTP …

Design Process Of A Novel Dynamic Mechanical Analysis Sample Preparation Methodology, Julian M. Richardson

Honors Theses

The technique of dynamic mechanical analysis (DMA) has been a frontrunner in the field of polymer science for decades. It’s used as a tool for characterization has been integral in mankind’s understanding of the properties of polymeric materials. The procedure for obtaining data using DMA is widespread and standardized, however the procedure for preparing the samples is a list of dimensions and tolerances with no mention of how to obtain said dimensions. Every research group using DMA is left to their own devices to prepare samples. This discontinuity can create the problem of nonuniform results across the scientific community. This …