Polymer and Organic Materials Commons^™

Pilot-Scale Spinning And Sucrose-Tetra-Aldehydes-Crosslinking Of Feather-Derived Protein Fibers With Improved Mechanical Properties And Water Resistance, Bingnan Mu, Faqrul Hassan, Qianmei Wu, Yiqi Yang

Department of Textiles, Merchandising and Fashion Design: Faculty Publications

Pliable and water-resistant protein fibers from feathers were developed via continuous one-step spinning and crosslinking using sucrose-tetra-aldehydes. Though flexible protein fibers from feathers were developed, poor wet stability and low tenacity still limit the large and high-end applications of feather-derived fibers. Despite that saccharide aldehydes are considered as an efficient and sustainable crosslinker, substantial concerns such as generation of formaldehyde, high consumption of modifiers, loss of mechanical properties, yellowing, and decline in dyeability of fibers, exist after crosslinking. In this work, we controlled structures of crosslinkers and incorporated disaccharide-tetra-aldehydes into a continuous wet-spinning line. No formaldehyde was generated in the …

Effect Of Freestream Noise On Hypersonic Crossflow-Induced Boundary-Layer Transition, Andrew Bustard, Thomas J. Juliano, Harrison B. Yates, Mark Noftz, Joseph Jewell

Publications

Between the windward and leeward rays, boundary-layer transition on cones at angle of attack in hypersonic flow is dominated by the crossflow instability [1, 2], wherein stationary and/or traveling crossflow vortices develop and can breakdown into turbulence [3]. Stationary crossflow modes are caused by surface roughness or any other steady forcing and produce disturbances that are fixed in place on the surface [3–6]. Stationary vortices create a generalized inflection point in the velocity profile that is inviscidly unstable [7]. This distorted mean flow develops secondary instabilities, whose growth and breakdown is one path to turbulence [8–10]. Traveling crossflow modes are …

Rheological Properties Of Recyclable Polymer Matrices For Advanced Composite Applications, Rahul Shankar

Dissertations

This dissertation focuses on evaluating the rheological characteristics of a variety of recyclable polymer matrices, which can compete with thermosets in a wide range of specialized applications. Studying the fundamental solid and melt-state viscoelastic properties and establishing structure-property-processing relationships is critical for the widespread adoption of these novel recyclable polymers in commercial applications. The first chapter provides an introductory overview of the different recyclable polymer matrices and their applications including high performance thermoplastics as thermoset replacements in high energy composite manufacture, multifunctional specialty thermoplastics for additive manufacturing and next generation, reprocessable covalent adaptable networks for self-healing applications. Furthermore, the important …

Understanding Process-Structure-Property-Performance Relationships Of Thermoplastic Olefins (Tpo) Foams Through A Novel Manufacturing To Response Pathway, Sai Aditya Pradeep

All Dissertations

The global transportation industry is the second highest contributor to climate change. As a result, there has been a concerted effort to spearhead research in economical lightweighting technologies, as every 10 % reduction in weight will lead to to 6 – 8 % improvement in fuel efficiency. Additionally, the recent push for electrification and the emphasis on Corporate Average Fuel Economy (CAFE) standards have seen original equipment manufacturers (OEM’s) dive into lightweighting of materials to improve overall range and/or fuel-efficiency. Thermoplastic Olefins (TPOs) have in recent years carved out a niche in the automotive industry due to advantages such as …

Investigation Of Optical And Structural Properties Of Gesn Heterostructures, Oluwatobi Gabriel Olorunsola

Graduate Theses and Dissertations

Silicon (Si)-based optoelectronics have gained traction due to its primed versatility at developing light-based technologies. Si, however, features indirect bandgap characteristics and suffers relegated optical properties compared to its III-V counterparts. III-Vs have also been hybridized to Si platforms but the resulting technologies are expensive and incompatible with standard complementary-metal-oxide-semiconductor processes. Germanium (Ge), on the other hand, have been engineered to behave like direct bandgap material through tensile strain interventions but are well short of attaining extensive wavelength coverage. To create a competitive material that evades these challenges, transitional amounts of Sn can be incorporated into Ge matrix to form …

Automated Mini-Tubular Ceramic Production, Hunter Brooks, Daniel Freeman, Leo Taranta-Slack

Mechanical Engineering

Researchers at Lawrence Livermore National Laboratory need a way to increase the rate of manufacturing of mini-tubular ceramics to be used in testing particulate air filters. This document outlines our process from researching and writing an initial scope of work all the way to fabricating and testing a final prototype. This journey takes us through the background research, ideation process and selection of a final design. We also detail the desired engineering specifications and our concept selection process. We dedicate a significant portion of this report to discussion of our final design. We delve into how it was manufactured as …

An Investigation Into Energy-Material Properties Interaction In Additive Manufacturing Of Polymers., Pu Han

Electronic Theses and Dissertations

Additive manufacturing (AM), known as three-dimensional (3D) printing, is a fabrication process to build 3D objects layer by layer based on computer aided design (CAD) model or digital 3D model. Fused filament fabrication (FFF) has become a preferred method for additive manufacturing due to its cost-effectiveness and flexibility. However, the parts built using FFF process suffer from lower mechanical strength compared to that fabricated using traditional method and rough surface finish. With this motivation, this dissertation aims to develop and implement a novel in-process laser assisted technique on FFF to heal the microstructure of FFF built objects by enhancing reptation …

Silver Microparticle And Submicron Wire - Polylactic Acid Composites For Additive Manufacturing, Jenna W. Robichaux

LSU New Orleans Theses and Dissertations

This thesis explores the incorporation of silver microparticle and submicron wire additives into thermoplastic filament feedstock for fused filament fabrication (FFF) to create multifunctional three-dimensional (3D) printable composites. The impact of silver microparticle and submicron wire additives on mechanical behavior along with antibacterial effect of the silver microparticle and submicron wire additives on printed objects were assessed.

Composite FFF filaments were fabricated by solution processing, granulation, and extrusion. Differential Scanning Calorimetry (DSC) was conducted to measure the glass transition and melting point temperatures of the composite filaments for 3D printing. The effect of the additive addition on the thermal properties …

Synthesis Of Polyethylene Glycol-Based Hydrogels And Silver/Gold Nanostructures For Biomedical Applications, Isabelle Ishimwe Niyonshuti

Graduate Theses and Dissertations

This work focuses on the synthesis of biocompatible polyethylene glycol (PEG)-based hydrogels, silver nanoparticles (AgNPs), and silver-gold nanocages (Ag-AuNCs) for biomedical applications. The dissertation includes two parts with Part I on the work of PEG-based hydrogel for wound healing applications and Part II on the work of Ag/Au nanostructures for antimicrobial applications. Part I studies PEG-based hydrogel for the delivery of fibroblast growth factors (FGFs) for wound healing applications, aiming to overcome the challenge of designing hydrogels capable of the sustained release of bioactive FGFs. This research develops new biocompatible anionic injectable hydrogel formulations based on Poly (Oligo Ethylene Glycol …

Explorations And Developments In Multifunctionality, 3d Printing, And Accelerated Aging For Thermoplastics And Thermosets, Zachary Brounstein

Nanoscience and Microsystems ETDs

If the world is to progress through the fourth industrial revolution, rapid advances in materials science must complement new technological feats in manufacturing, computation and device functionality, and a broader understanding of how materials behave as they age and degrade. To this effect, much effort has been directed towards polymeric materials to address and solve many problems in this new era. This includes developing polymer composites that incorporate fillers to imbue multifunctionality, fabricating novel formulations for additive manufacturing, and conducting aging studies to assess the performance of these materials over long time spans. Building and expanding on the latest research …

Optimization In The Application Of Varnishes Barrier On Cartonboard Packaging, Andre Ramalheiro De Andrade, Maria Isabel Rodrigues Phd, Eduardo Luiz Machado Phd

Journal of Applied Packaging Research

In this work adjustments in the rotogravure printing process are proposed to the varnish water vapor transmission rate (WVTR) aiming to obtain results smaller than 20g/m²/24h. One case study was used for the propositions for improvements, where focused on varnish application process in a gravure printer for an eight-printing unit cartonboard packaging, maximum printing speed of 175 m/min and a 285 g/m² weight cartonboard. The possible variables that influenced the WVTR result were selected from the technical expertise of the people involved in the project, the analysis in the printing process with the application of directed trials using experimental designs …

Chitosan Graphene Composite Fabrication And Characterization For Treatment Of Harmful Algal Blooms And Toxins, Sarah Zetterholm

Master's Theses

Chitosan graphene composites were fabricated and characterized as a management strategy for harmful algal blooms (HABs) caused by various species of cyanobacteria. These chitosan graphene materials were compared to previously studied chitosan graphene-oxide composites in both material properties and HAB treatment. In previous studies, adsorption of the cyanobacteria onto the surface of the composite materials has been observed. Investigations of the pure materials for these composites are also included in this study to determine whether removal is a result of charge interactions with the composite, or as an inherent property of the graphene or graphene oxide. Initial results suggest that …

Development Of The Composition Of A Composite Material Based On Thermoreactive Binder Ed-20, Umida Ziyamukhamedova, Gavhar Miradullayeva, Erkin Rakhmatov, Jasur Nafasov, Mavtuna Inogamova

CHEMISTRY AND CHEMICAL ENGINEERING

The aim of the study is to determine the effect of the type of structural modifier and filler on the structure formation and technological properties of potting composite polymeric materials (HCPM) and protective coatings for sheet and complex-configuration technological equipment, taking into account their rheological properties. Compositions of composite polymer materials based on a thermosetting binder of epoxy-diane resin ED-20 filled with a mineral filler - kaolin modified with gassipol resin (GS) - were developed using Newton's interpolation formula and the Lagrange method. The optimal amount of gossypol resin determined in the composition of the composite – in the amount …

Effect Of Talc On The Properties Of A Compound Based On Ethylene-Propylene Copolymer, Ikromjon Usmanov, Farrukh Kurbanbekov, Bobir Aykhodjaev, Ravshan Adilov

CHEMISTRY AND CHEMICAL ENGINEERING

The aim of the research is to study the possibility of replacing Korean-made talc with inexpensive talc from an Afghan deposit, processed in Uzbekistan and used for the production of polypropylene compounds. In the future, these compounds are used for the manufacture of plastic car parts. A block copolymer produced by Uz Kor Gaz Chemical was chosen as a binder. For this, the influence of the content and type of talc on the properties of a compound based on an ethylene-propylene copolymer was studied.

The properties of the obtained compounds checked using ISO standards. The fractional composition of the studied …

Poly(2-Hydroxyethyl Methacrylate) Hydrogels For Contact Lens Applications–A Review, Kushendarsyah Saptaji, Nurlaely Rohmatul Iza, Sinta Widianingrum, Vania Katherine Mulia, Iwan Setiawan

Makara Journal of Science

The emerging technology in biomedical engineering requires biocompatible materials, which are also referred to as biomaterials. For a material to be considered biocompatible, it should not interact with human tissues in a harmful way, and vice versa. Various properties of biocompatible materials, such as mechanical and optical properties, have to be considered for different biomedical applications. One of the most popular applications of biomaterials is for contact lenses. Hydrogels, specifically poly(2-hydroxyethyl methacrylate) (PHEMA) hydrogels, are among the most popular ones in ophthalmologic applications, especially in soft contact lenses. This paper reviews the use of PHEMA hydrogels as one of the …

Biodegradable Nanocomposite Multifunctional Packaging Film For Fruits, Kalpani Y. Perera, Shubham Sharma, Dileswar Pradhan, Amit Jaiswal, Swarna Jaiswal

Articles

Biopolymers have been used in food packaging in recent years due to high pollution rates and decreased biodegradation of synthetic polymers. Chitosan (CH) and Sodium alginate (SA) are both biodegradable biopolymers with excellent film forming capability. TiO2 nanoparticles have high mechanical strength, degradation ability and antimicrobial properties, which are beneficial in food packaging. The aim of the current work is to develop the biodegradable multifunctional nanocomposite film for fruit (i.e., Pear) packaging applications. Bionanocomposite film was prepared by solvent casting method using CH-SA and various concentrations of TiO2. The multifunctional properties such as UV barrier, thermal, water retention, mechanical, chemical, …

Seaweed Polysaccharide In Food Contact Materials (Active Packaging, Intelligent Packaging, Edible Films, And Coatings), Kalpani Y. Perera, Shubham Sharma, Amit K. Jaiswal, Swarna Jaiswal

Articles

Food contact materials (FCMs) are materials that come in contact with food products such as food packaging which play a significant role in the food quality and safety. Plastic, which is a major food packaging material, harms the eco-system, wildlife, and the environment. As a result, numerous researches have been in progress on alternative polymers, which has similar properties as plastic but is also environmentally friendly (biodegradable). In recent years, the utilization of seaweed polysaccharides has piqued interest due to its biodegradability, non-toxicity, antioxidant capabilities, and excellent film formation ability. However, it has a number of drawbacks such as low …

Tools And Strategies For The Patterning Of Bioactive Molecules And Macromolecules, Daniel J. Valles

Dissertations, Theses, and Capstone Projects

Hypersurface Photolithography (HP) is a printing method for fabricating structures and patterns composed of soft materials bound to solid surfaces and with ~1 micrometer resolution in the x, y, and z dimensions. This platform leverages benign, low intensity light to perform photochemical surface reactions with spatial and temporal control of irradiation, and, as a result, is particularly useful for patterning delicate organic and biological material. In particular, surface- initiated controlled radical polymerizations can be leveraged to create arbitrary polymer and block- copolymer brush patterns. Chapter 1 will review the advances in instrumentation architectures from our group that have made these …

Development And Characterization Of Composite Membranes For Use In Countercurrent Solvent Extraction, Lydia Neves Rodrigues

Dissertations

Porous membranes having a particular wetting characteristic, hydrophobic or hydrophilic, are used for nondispersive membrane solvent extraction (MSX) where two immiscible phases flow on two sides of the membrane. The aqueous-organic phase interface across which solvent extraction/back extraction occurs remains immobilized on one surface of the membrane. This process requires the pressure of the phase not present in membrane pores to be either equal to or higher than that of the phase present in membrane pores; the excess phase pressure should not exceed a breakthrough pressure. In countercurrent MSX with significant flow pressure drop in each phase, this often poses …

Evaluation Of Stretch Film Behavior During Long-Term Storage Under Different Atmospheric Conditions, Kyle Dunno, Maria Symanski

Journal of Applied Packaging Research

This study examined the post-application behavior of two 20.3 micron machine stretch films, one categorized as high-performance and one as general-performance, for thirty days while stored at either 23°C or 38°C. For each film type, the stretch film was applied to a simulated unit load to produce neutral and positive applied total stretch scenarios. The relaxation curves developed from each test indicate the relaxation rate of the films varied based on the storage condition. Observed was an average of 41% containment loss for both high-performance and general-purpose films when the simulated loads were stored at 38°C. For simulated loads stored …