Materials Science and Engineering Commons^™

The Influence Of Extrusion Geometry And Ratio On Extrudate Mechanical Properties For A 6005a Alloy Containing Either Sc And Zr Or Cr And Mn Dispersoid Formers, Eli A. Harma, Paul Sanders, Thomas Wood, Timothy Langan

Michigan Tech Publications

There is a demand for a 6005A series extrusion alloy with improved strength that maintains good extrudability. Replacing Mn and Cr dispersoid formers with Sc and Zr is expected to increase the room temperature mechanical properties while not affecting extrudability. Al3X dispersoids with a Sc core surrounded by a Zr shell are stable at higher temperatures and enhance recrystallization resistance and precipitation strengthening. However, there is little information on how the Sc and Zr additions affect the properties of an extrudate as a function of extrusion geometry and ratio. A 6005A series alloy with Cr and Mn additions is compared …

Reliability Of Cazro3 And Mgo Capacitors At High Temperatures, Alan Devoe, Hung Trinh, Fatih Dogan

Materials Science and Engineering Faculty Research & Creative Works

Calcium zirconate and magnesium oxide have both been found to have useful dielectric properties at high temperatures. Multilayer ceramic capacitors (MLCCs) were made with these dielectrics and platinum electrodes. The relationship between the lifespan (mean-time to failure) and applied voltage was determined using Weibull statistics. CaZrO₃ capacitors were tested between 550◦C and600◦C while MgO capacitors were tested between 600◦C and 650◦C. The temperature coefficient Ea and the voltage coefficient n of the Prokopowicz Vaskas equation were determined under various test conditions. Activation energiesforcalciumzirconateandmagnesiumoxidewere3.25eVand3.48eV, respectively. Resistance degradation of CaZrO₃ and MgO capacitors, tested at 600◦Cand250V, were compared.

Development Of Non-Precious Iron-Cobalt Alloy Catalyst For Electrocatalytic Reaction, Harsh Panchal

Electronic Theses & Dissertations

The development of a FeCo alloy catalyst with tunable Fe/Co ratios is examined to improve electrocatalytic performance in reactions like the oxygen evolution reaction (OER), hydrogen evolution reaction (HER), and oxygen reduction reaction (ORR). Many energy conversion devices, such as fuel cells, metal-air batteries, and water-splitting systems, depend on these interactions to function. These technologies have huge potential to meet the increasing need for hydrogen production and renewable energy sources worldwide, which are critical to attaining a sustainable energy future. When compared with noble metal-based catalysts, the FeCo alloy catalyst shows much higher catalytic activity, according to previous studies. Hydrothermal …

Production Of Sustainable Liquid Fuel From Waste Polymeric Materials Via Thermal Pyrolysis, Md. Sabbir Ahmed, Selim Reja, Sk Md Ali Zaker Shawon, Farhana Nazmin, Abdullah Mohammad Sarjish, Yousuf Ali, M. Azizur R. Khan, M. Jasim Uddin, Md. Wasikur Rahman

Mechanical Engineering Faculty Publications

The widespread use of polymeric materials has become an environmental threat as they are durable and nonbiodegradable in nature, which is directly responsible for severe ecological consequences. Thermal pyrolysis offers a sustainable and efficient approach to converting these polymeric waste materials into liquid fuel, which is also referred to as pyrolysis oil (PO). In this study, a novel method was developed for producing oil from a composite of waste polymers that include vehicle tires, tubes, and medical waste. A fixed-bed stainless steel reactor is used to thermally breakdown the waste polymeric feedstock (300–750°C) in an inert environment. The PO was …

Direct Computations Of Spatially Resolved Viscoelastic Moduli Of Biomolecular Condensates, Liwen Gu

McKelvey School of Engineering Graduate Student Theses & Dissertations

Biomolecular condensates are viscoelastic materials formed by liquid-liquid phase separations (LLPS) of biopolymers. In this study, we develop a modified graph Laplacian-based collective model to characterize viscoelastic heterogeneity within condensates based on results of lattice-based Metropolis Monte Carlo (MMC) simulations. By integrating random graph models and simulations of A1-LCD, a type of intrinsically disordered protein, we examine how network topology influences storage modulus, loss modulus, crossover frequency, and relaxation time spectra. Our results reveal a strong correlation between topological features and mechanical response, with the condensate interior exhibiting higher stiffness and faster relaxation than the interface. The relaxation spectra provide …

Functional Devices Based On Freestanding 2d Materials, Shijue Xu

McKelvey School of Engineering Graduate Student Theses & Dissertations

Two-dimensional (2D) materials have attracted extensive attention in the field of nanoelectronics due to their atomic-scale thickness, high surface-to-volume ratio, tunable electronic properties, and compatibility with low-temperature processing. These characteristics make them highly suitable for the construction of emerging device architectures, particularly in both ionic and electronic devices.

In this work, we investigate the application of 2D materials in two distinct classes of devices: ionically-driven memristors and electronically-dominated metal–semiconductor contacts. For the memristor study, we fabricate heterostructure-based resistive switching devices using h-BN and WSe₂ as active layers. These 2D material-based memristors exhibit stable power consumption loops and high linearity …

Biogenic Synthesis Of Metallic And Bimetallic Oxide Nanoparticles For Water Treatment Applications, Gunarani G.I

Theses and Dissertations

Access to clean water is a quality-of-life indicator. The availability of clean water apart from water scarcity is marred due to contamination by heavy metals and synthetic dyes, posing a grave environmental and public health challenge. This necessitates the implementation of advanced and sustainable treatment solutions towards water remediation. This research work focusses on the fabrication and application of biogenic and chemically synthesized metallic and bimetallic nanoparticles for the efficient removal of uranium, chromium, and toxic dyes from aqueous environments. The study particularly focuses on zero-valent (C-Fe and B-Fe) and bimetallic (C-NiFe and B-NiFe) nanoparticles, evaluating their adsorption capabilities and …

Rare Earth Mineral Flotation – A Comparison Of Silicates To Oxides, Carbonates And Phosphates, Abdul Mamudu

Graduate Theses & Non-Theses

Flotation is a processing method used to separate valuable minerals from gangue minerals based on differences in hydrophobicity. When applied to ores bearing rare earth minerals (REMs) variations in rare earth element (REE) concentrations within the REMs can lead to inconsistent flotation results. Prior work at Montana Technological University examined the adsorption of collectors on the surfaces of synthetic REMs to assess recovery via flotation. Previous studies showed that the results obtained for Salicyl Hydroxamic Acid (SHA) on rare earth oxides REO), rare earth carbonates (REC), and rare earth phosphates (REP) vary depending on the coordination number (CN) and the …

First-Principles Studies Of Electrical Polarization Effects In Ferroelectrics, Antiferroelectrics And Defects, Louis Alaerts

Dartmouth College Ph.D Dissertations

Over the last few decades, density functional theory (DFT) has emerged as a formidable tool in the field of computational material science. Not only has it become a complementary method approach to experiments by rationalizing the many complex properties of materials but its formidable predictive power can also be used to identify the most promising candidates for specific applications. Point defects in semiconductors have become an important platform for the development of quantum networks due to their ability to act as spin-photon interfaces. Spectral diffusion, the broadening of the optical emission line, can significantly impact the performance of these defect-based …

Low-Field Magnetoresistance In Nanocomposites Of La₀.₇Sr₀.₃Mno₃ And Metal Oxides, Nicholas K. Thiel-Hudson

University Scholar Projects

Pure La_0.7Sr_0.3MnO₃ (LSMO) exhibits colossal magnetoresistance (CMR) with large applied magnetic field over a narrow temperature range (intrinsic behavior), limiting its application to narrow temperature ranges. In contrast, the extrinsic CMR effect originates from inhomogeneities at larger length scales, such as grain boundaries and phase separation, where the structural features act as tunneling barriers, leading to a low-field magnetoresistance (LFMR) response, thereby expanding the application of LSMO into the low-field regime over a broader temperature range. In this work, the magnetotransport behavior of pure LSMO thin film is compared to the composite layered heterostructures of …

Understanding Initial Capacity Loss In Substituted Layered Oxide Cathodes For Lithium-Ion Batteries, Gy Wyco

Graduate Dissertations and Theses

Layered oxide LiCoO₂ (LCO) pioneered the commercialization of lithium-ion batteries (LIBs) in 1991, yet the growing demand for higher energy density has driven the development of substituted layered oxides, including LiNiᵧMn𝓏Co₁₋ᵧ₋𝓏O₂ (NMC) and LiNiᵧCo₁₋ᵧ₋𝓏Al𝓏O₂ (NCA). Despite the increased energy density, achieving full lithium reversibility during the first charge-discharge cycle remains a critical challenge: approximately 0.08–0.11 Li is “irreversibly” lost after delithiation, resulting in a substantial capacity loss of 10–15%. This loss is conventionally attributed to bulk lithium transport limitations arising from three interrelated factors: (1) contraction of the c-axis lattice during lithiation, (2) reduced rate of tetrahedral site hopping (TSH) …

Characterizing Heating And Resistance Properties Of Nichrome Burn Wire To Be Used In Cubesat Actuation, Noah Moix

Mechanical Engineering Undergraduate Honors Theses

This thesis investigates the use of Nichrome 60 wire as a burn wire mechanism, commonly utilized in CubeSats and other aerospace engineering applications requiring precise, single-use release systems. The experiment focused on characterizing the thermal and resistive behavior of Nichrome 60 wire under Joule heating conditions. Four wire configurations were tested: 34-gauge and 36-gauge wires, each at lengths of 1 inch and 2 inches. Each configuration was subjected to a constant current until thermal failure occurred. During testing, real-time measurements of electrical resistance and wire temperature were recorded. This data was used to generate resistance vs. temperature profiles for each …

Thermal Characterization Of 3d Printing Materials For Increasing Insulation Potential And Practicality, Jackson H. Minnick

Mechanical Engineering Undergraduate Honors Theses

This study served as an exploration into the possible existence of a correlation between the infill lattice structure of a 3D printed wall section and the thermal performance of that sample as characterized by thermal conductivity measured in units of Watts per meter Kelvin. With the continual increase in the practicality, fidelity, and applicable fields of additive manufacturing, namely FDM 3D printing, research on specific print characteristics and their effects on the material and thermal characteristics of the part in question is steadily becoming more commonplace. Although the thermal conductivity of 3D printed wall sections as a function of infill …

Remaining Life Analysis Of Pipeline Gas With Extreme Value Theory, Rony Prayitno Simeon, Eddy Sumarno Siradj, Tedi Kurniawan

Journal of Materials Exploration and Findings

Energy and chemical companies use pipelines to transfer oil, gas, and other materials from one place to another, within and between their plants. Pipeline integrity is an important concern because pipeline leakage could result in serious economic or environmental losses. Some research has applied to understand the effect of extrapolation value of the minimum thickness of pipeline by using the Extreme Value Theory. In this research, both statistical models and Extreme Value methods were applied and developed for the reliability of the pipeline by assuming the constant corrosion rate and deviation due to measuring devices were neglected. The research obtained …

Integrity Assessment Of Shipping Line Pipelines Using Risk-Based Analysis To Determine Risk And Maintenance Strategies, Ade Ratih Anggraini, Dwi Marta Nurjaya

Journal of Materials Exploration and Findings

Pipeline Shipping Lines X, Y & Z are classified as critical infrastructure, being the only transportation through the crude oil lifting from P and R location to the transfer station in NM Area. To maintain the workflow of the Shipping Line, integrity assessments and risk evaluation are required to ensure the operational and safety. Anomalies were found by analysing inspection, monitoring, and repair data, while the pipelines' future integrity was assessed by calculating the remaining life. Risk-Based Analysis (RBA), which is a modification of Kent Muhlbaeur's method, is employed to conduct the risk assessment using the Probability of Failure (POF) …

Characteristics Of Carbonaceous Materials Synthesized From Palm Oil Empty Fruit Bunch Waste Using Ferrocene Catalyst, Ahmad Nabil Shahab, Adinda Izzatul Islam, Afif Wardana, Ilham Nur Dimas Yahya, Ary Yanuar Tri Amalia, Nofrijon Sofyan, Donanta Dhaneswara

Journal of Materials Exploration and Findings

The synthesis of carbonaceous materials for reduced graphene oxide (rGO) precursors using oil palm empty fruit bunches waste as a carbon source offers a sustainable solution for waste management in the palm oil industry while delivering high-performance materials. The oil palm empty fruit bunches were carbonized, followed by acid washing, pyrolysis with ferrocene (8%, 12%, and 16% variations), and ultrasonication to produce rGO. The structural, electronic, and morphological properties of the rGO were analyzed using various characterization techniques. The band gap values decreased with increasing ferrocene concentration, from 1.14 eV (8%) to 1.06 (16%), indicating enhanced electronic conductivity. XRD analysis …

Assessment Of H2s-Induced Cracking Susceptibility In Steam Line Pipes And Weld Zones During Geothermal Well Construction, Riene Kaelamanda Pragitta, Yudha Pratesa

Journal of Materials Exploration and Findings

The susceptibility of steam line pipes, especially in the HAZ (heat-affected zone) and weldment areas, to hydrogen sulfide in the geothermal industry is crucial to understand from the early stages, particularly during construction. The combination of tensile stress from residual stresses after welding and metallurgical phase transformation makes the joint areas vulnerable to sulfide stress cracking. This condition becomes even more extreme when the equipment operates during the well stimulation phase. This research assesses the severity of H₂S-induced cracking using NACE MR0175 and ISO 15156-1 standards, focusing on the effects of pH and partial pressure of H₂S (p_{H₂S …}

Defect Characterization Of Sic Schottky Barrier Diode Using Deep Level Transient Spectroscopy, Zachary I. Mccoy

Electrical Engineering and Computer Science Undergraduate Honors Theses

The aim of this project is to use deep level transient spectroscopy (DLTS) to energetically evaluate defects by using the carrier concentration dependence on temperature and where these carriers may experience deviation from standard predictions. These defects become apparent through multiple C-V measurements that are swept through a temperature range. By analyzing trends with respect to temperature, the defects can be energetically “located,” and thus identified. This identification can help streamline semiconductor material manufacturing/growth because DLTS identifies potential defect causes by providing data to characterize semiconductor mid-band defects. DLTS can assess nearly all parameters associated with traps/defects including density, thermal …

The Evolution Of Nanoparticles In Nanoparticle Doped Optical Fibers, Mary Cahoon

All Dissertations

Optical fiber and fiber laser technologies based on silica glass are critical to many technologies today. One method to improve the optical performance of laser fibers is engineer the local environment around the active elements in the glass. To that end, this Dissertation focused on the fabrication and characterization of fibers made with nanoparticles incorporated into the glass to control the local composition. First, the nanoparticle composition and structure was analyzed as it evolved from from the initially-synthesized form to incorporation into the dense aluminum-silicate glass. The aluminum oxide in the glass was found to be important not only to …

Development And Characterization Of A Pro-Angiogenic Peptide Amphiphile For Deep Dermal Burn Healing Via Spray Delivery, Loria Dimartino

Honors Theses

Severe burns and other dermatological injuries are frequently accompanied by a range of comorbidities and aesthetic challenges that patients must contend with. The complexity of burn care is exacerbated by the lack of a standardized surgical protocol, as treatment strategies are tailored to individual patient factors, including overall health status, wound size and location, as well as the expertise and resources available to the surgical team. Most commonly, deep dermal burns are treated through grafting, which effectively covers the injury site, but requires the creation of a second wound on the body of approximately the same size. This produces a …