Materials Science and Engineering Commons^™

Intergranular Corrosion And Stress Corrosion Cracking Of Extruded Aa6005a, David James Seguin

Dissertations, Master's Theses and Master's Reports - Open

A research program focused on understanding the intergranular corrosion (IGC) and stress corrosion cracking (SCC) behavior of AA6005A aluminum extrusions is presented in this dissertation. The relationship between IGC and SCC susceptibility and the mechanisms of SCC in AA6005A extrusions were studied by examining two primary hypotheses.

IGC susceptibility of the elongated grain structure in AA6005A exposed to low pH saltwater was found to depend primarily on the morphology of Cu-containing precipitates adjacent to the grain boundaries in the elongated grain structure. IGC susceptibility was observed when a continuous (or semi-continuous) film of Cu-containing phase was present along the grain …

Accurate Prediction Of Spectral Phonon Relaxation Time And Thermal Conductivity Of Intrinsic And Perturbed Materials, Tianli Feng

Open Access Theses

The prediction of spectral phonon relaxation time, mean-free-path, and thermal conductivity can provide significant insights into the thermal conductivity of bulk and nanomaterials, which are important for thermal management and thermoelectric applications. We perform frequency-domain normal mode analysis (NMA) on pure bulk argon and pure bulk germanium. Spectral phonon properties, including the phonon dispersion, relaxation time, mean free path, and thermal conductivity of argon and germanium at different temperatures have been calculated. We find the dependence of phonon relaxation time τ on frequency ω and temperature T vary from ~ω^-1.3 to ~ω^-1.8 and ~T^-0.8 to ~T^{-1.8 …}

High Speed Turning Of Compacted Graphite Iron (Cgi) Using Controlled Modulation, Tyler Paul Stalbaum

Open Access Theses

Compacted graphite iron (CGI) is a material which emerged as a candidate material to replace cast iron (CI) in the automotive industry for engine block castings. Its thermal and mechanical properties allow the CGI-based engines to operate at higher cylinder pressures and temperatures than CI-based engines, allowing for lower fuel emissions and increased fuel economy. However, these same properties together with the thermomechanical wear mode in the CGI-CBN system result in poor machinability and inhibit CGI from seeing wide spread use in the automotive industry.

In industry, machining of CGI is done only at low speeds, less than V = …

Rapid Repair Of Severely Damaged Rc Columns With Different Damage Conditions: An Experimental Study, Ruili He, Lesley Sneed, Abdeldjelil Belarbi

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

No abstract provided.

Investigation Of Nbnx Thin Films And Nanoparticles Grown By Pulsed Laser Deposition And Thermal Diffusion, Ashraf Hassan Farha

Electrical & Computer Engineering Theses & Dissertations

Niobium nitride films (NbNx) were grown on Nb and Si (100) substrates using pulsed laser deposition (PLD), laser heating, and thermal diffusion methods. Niobium nitride films were deposited on Nb substrates using PLD with a Q-switched Nd: YAG laser (λ = 1064 nm, 40 ns pulse width, and 10 Hz repetition rate) at different laser fluences, different nitrogen background pressures and deposition temperatures. The effect of changing PLD parameters for films done by PLD was studied. The seen observations establish guidelines for adjusting the laser parameters to achieve the desired morphology and phase of the grown NbNx films.

When the …

Applications Of High Throughput (Combinatorial) Methodologies To Electronic, Magnetic, Optical, And Energy-Related Materials, Martin L. Green, Ichiro Takeuchi, Jason R. Hattrick-Simpers

Faculty Publications

High throughput (combinatorial) materials science methodology is a relatively new research paradigm that offers the promise of rapid and efficient materials screening, optimization, and discovery. The paradigm started in the pharmaceutical industry but was rapidly adopted to accelerate materials research in a wide variety of areas. High throughput experiments are characterized by synthesis of a “library” sample that contains the materials variation of interest (typically composition), and rapid and localized measurement schemes that result in massive data sets. Because the data are collected at the same time on the same “library” sample, they can be highly uniform with respect to …

A Laboratory Experiment Using Nanoindentation To Demonstrate The Indentation Size Effect, Wendelin Wright, Gang Feng, William D. Nix

Faculty Journal Articles

A laboratory experiment using nanoindentation to demonstrate the indentation size effect is described. This laboratory introduces students to sophisticated instrumentation at low cost and low risk and utilizes recent research in the materials community as its foundation. The motivation, learning objectives, experimental details, data, and data analysis are presented. This experiment is intended for use in an upper-division materials science elective at the university level and has been successfully used in laboratory courses for senior undergraduates and first-year graduate students at Stanford University and Santa Clara University.

The Processing Of Aluminum Gasarites Via Thermal Decomposition Of Interstitial Hydrides, Joseph James Licavoli

Dissertations, Master's Theses and Master's Reports - Open

Gasarite structures are a unique type of metallic foam containing tubular pores. The original methods for their production limited them to laboratory study despite appealing foam properties. Thermal decomposition processing of gasarites holds the potential to increase the application of gasarite foams in engineering design by removing several barriers to their industrial scale production. The following study characterized thermal decomposition gasarite processing both experimentally and theoretically. It was found that significant variation was inherent to this process therefore several modifications were necessary to produce gasarites using this method. Conventional means to increase porosity and enhance pore morphology were studied. Pore …

Liquid Phase Sintering Of 20bi(Zn₀.₅Ti₀.₅)O₃-80batio₃ Dielectrics With Bismuth-Zinc-Borate And Bismuth Borosilicate Glasses, David I. Shahin

Masters Theses

"Dielectrics in the Bi(Zn₀.₅Ti₀.₅O₃-BaTiO₃ system (specifically 20BZT-80BT, in mol%) are promising candidates for high energy density capacitor applications due to broad temperature-dependent dielectric constant maxima and a relatively field-independent permittivity. Bulk samples require sintering temperatures of greater than 1180ºC to reach useful densities. Due to incompatibility of Bi with low-pO₂ processing, BZT-BT-based multilayer capacitors must utilize noble metal electrodes that resist oxidation during sintering. Sintering temperatures must be reduced to allow use of less expensive electrode materials (Cu, etc.). This work studies the reduced temperature sintering behavior and dielectric properties of BZT-BT sintered with 30 Bi₂O₃-30ZnO-40B₂O₃ and 50Bi₂O₃-25B₂O₃-25SiO₂ (mol%) liquid …

Processing And Properties Of Zrb₂-Zrsi₂ Matrix Composites Reinforced With Continuous Sic Fiber, Benjamin John Bowin Lai

Masters Theses

"The research presented in this thesis focuses on the processing, microstructure, and mechanical properties of ZrB₂-based composites. The main goal was to develop a process that incorporates high strength continuous SiC fiber in a ZrB₂-based matrix. In order to achieve this, the densification, microstructure, and mechanical properties of ZrB₂-ZrSi₂ monolithic ceramics were characterized along with various SiC fiber reinforced ceramic matrix composites (CMCs) utilizing the same matrix.

There were two main areas of study in this thesis. The initial study demonstrated that additions of ZrSi₂ into a ZrB₂ ceramic increases densification at significantly reduced processing temperatures ≤1600ºC). This study revealed …

Characterization Of And Controlling Morphology Of Ultra-Thin Nanocomposites, Guy C. Laine

Theses and Dissertations--Chemical and Materials Engineering

Ultrathin film nanocomposites are becoming increasingly important for specialized performance of commercial coatings. Critical challenges for ultrathin film nanocomposites include their synthesis and characterization as well as their performance properties, including surface roughness, optical properties (haze, refractive index as examples), and mechanical properties. The objective of this work is to control the surface roughness of ultrathin film nanocomposites by changing the average particle size and the particle volume fraction (loading) of monomodal particle size distributions. This work evaluated one-layer and two-layer films for their surface properties. Monodispersed colloidal silica nanoparticles were incorporated into an acrylate-based monomer system as the model …

Influence Of Surface Modification On Properties And Applications Of Complex Engineered Nanoparticles, Binghui Wang

Theses and Dissertations--Chemical and Materials Engineering

Complex engineered nanoparticles (CENPs) are being used on various applications. Their properties are different from those of neat nanoparticles. The dissertation explores these differences from four aspects: 1) Modify carbon nanomaterials’ inert surfaces and investigate the effect on thermal and rheological behavior of their dispersions; 2) Generate self-assembly bi-layer structure of oxide nanoparticles via surface modification; 3) Study interaction between lysozyme and different surface-charged ceria nanoparticles; 4) Investigate the biodistribution and transformations of CENPs in biological media.

An environment-friendly surface modification was developed to modify surfaces of carbon nanomaterials for increasing their affinity to non-polar fluid. It can offset formation …

Structural Tailoring Of Nanoporous Metals And Study Of Their Mechanical Behavior, Lei Wang

Theses and Dissertations--Chemical and Materials Engineering

Nanoporous (np) metals and alloys are the subject of increasing research attention due to their high surface-area-to-volume ratio. Numerous methods exist to create np metals, with dealloying being a common approach. By dissolving one or more elements from certain alloy systems, porous structure can be generated. Utilizing this method, multiple np metals, including np-Ni, np-Ir, and np-Au were created. By carefully adjusting precursor type and dealloying conditions for each system, nanoporous Ni/Ir/Au with different morphologies and even controllable ligament/pore size were achieved.

The mechanical behavior of porous materials is related to their fully dense counterparts by scaling equations. Established scaling …

Electromechanical Interaction On The Deformation Behavior Of Metallic Materials, Guangfeng Zhao

Theses and Dissertations--Chemical and Materials Engineering

Metallic materials play important roles in providing electrical, thermal, and mechanical functions in electronic devices and systems. The understanding of the electrical-thermal-mechanical interaction caused by the passage of electric current with high density is important to improve the performance and reliability of electronic assembly and packaging. The electromechanical interaction on the deformation behavior of copper and tin is studied in this work.

The electromechanical response of Cu strips was studied by passing a DC electric current. The electric resistance linearly increased with time before the occurrence of electric fusing. The electrothermal interaction led to the buckling of the Cu strips …

Structural, Optical And Electrical Properties Of Yttrium-Doped Hafnium Oxide Nanocrystalline Thin Films, Abhilash Kongu

Open Access Theses & Dissertations

Hafnium oxide (HfO2) has emerged as the most promising high-k dielectric for Metal-Oxide-Semiconductor (MOS) devices and has been highlighted as the most suitable dielectric materials to replace silicon oxide because of its comprehensive performance. In the present research, yttrium-doped HfO2 (YDH) thin films were fabricated using RF magnetron sputter deposition onto Si (100) and quartz with a variable thickness. Cross-sectional scanning electron microscopy coupled with Filmetrics revealed that film thickness values range from 700 A° to 7500 A°. Electrical properties such as AC Resistivity and current-voltage (I-V) characteristics of YDH films were studied. YDH films that were relatively thin (<1500 A°) crystallized in monoclinic phase while thicker films crystallized in cubic phase. The band gap (Eg) of the films was calculated from the optical measurements. The band gap was found to be ∼5.60 eV for monoclinic while it is ∼6.05 eV for cubic phase of YDH films. Frequency dependence of the electrical resistivity (ρac) and the total conductivity of the films were measured. Resistivity decreased (by three orders of magnitude) with increasing frequency from 100 Hz to 1 MHz, attributed due to the hopping mechanism in YDH films. Whereas, while ρac∼1Ω-m at low frequencies (100 Hz), it decreased to ∼ 104 Ω-cm at higher frequencies (1 MHz). Aluminum (Al) metal electrodes were deposited to fabricate a thin film capacitor with YDH layer as dielectric film thereby employing Al-YDH-Si capacitor structure. The results indicate that the capacitance of the films decrease with increasing film thickness. A detailed analysis of the electrical characteristics of YDH films is presented.

Reducing Metal Alloy Powder Costs For Use In Powder Bed Fusion Additive Manufacturing: Improving The Economics For Production, Fransisco Medina

Open Access Theses & Dissertations

Titanium and its associated alloys have been used in industry for over 50 years and have become more popular in the recent decades. Titanium has been most successful in areas where the high strength to weight ratio provides an advantage over aluminum and steels. Other advantages of titanium include biocompatibility and corrosion resistance. Electron Beam Melting (EBM) is an additive manufacturing (AM) technology that has been successfully applied in the manufacturing of titanium components for the aerospace and medical industry with equivalent or better mechanical properties as parts fabricated via more traditional casting and machining methods. As the demand for …

Process Study And Control Of Electron Beam Melting Technology Using Infrared Thermography, Jorge Mireles

Open Access Theses & Dissertations

An IR camera was installed in an Arcam A2 system (Arcam AB, Mölndal, Sweeden) and layer-by-layer image acquisition was achieved. The camera's capability to detect manufacturing defects was evaluated by implementing computer vision techniques using LabVIEW measurement and programming software (National Instruments, Austin, TX). Thermal maps acquired by the IR camera allowed layer-by-layer part temperature to be recorded. A core objective of this research was to study the impact of processing temperature on EBM-fabricated Ti-6Al-4V parts and achieve controlled mechanical properties. In this research, build variations were achieved by modifying parameters that change processing temperature from the standard processing temperature. …

Effect Of Microwave Heating On The Migration Of Additives From Ps, Pp And Pet Container Into Food Simulants, Ruoyin Cai

Theses

Microwave food packaging has become a tremendous element in the food manufacturing process. The purpose of any food packaging regulations concerned with the safety of the food is to control and limit the migration of substances from the packaging into the food. The main objective of this thesis is to test three different microwaving packaging materials that are the most common material in the market, viz. polystyrene (PS), polypropylene (PP), and polyethylene terephthalate (PET), migrated into four food simulant solutions. Four different simulant solutions were used based on the food type and FDA recommendations and regulations. These food simulants include …

Non-Equilibrium Melting And Sublimation Of Graphene Simulated With Two Interatomic Potentials, Brad Steele

USF Tampa Graduate Theses and Dissertations

The mechanisms of the sublimation of graphene at zero pressure and the condensation of carbon vapor is investigated by molecular dynamics (MD) simulations. The interatomic interactions are described by the Reactive Empirical Bond Order potential (REBO). It is found that graphene sublimates at a temperature of 5,200 K. At the onset of sublimation, defects that contain several pentagons and heptagons are formed, that are shown to evolve from double vacancies and stone wales defects. These defects consisting of pentagons and heptagons act as nucleation sites for the gaseous phase. The influence of the interatomic interactions on the sublimation process are …

Improving Tribological Properties Of Cast Al-Si Alloys Through Application Of Wear-Resistant Thermal Spray Coatings, David Culliton, Tony Betts, Sandra Carvalho, David Kennedy

Articles

Flame Spray Thermal Spray coatings are low-cost, high-wear surface-treatment technologies. However, little has been reported on their potential effects on cast automotive aluminum alloys. The aim of this research was to investigate the tribological properties of as-sprayed NiCrBSi and WC/12Co Flame Spray coatings applied to two cast aluminum alloys: high-copper LM24 (AlSi8Cu3Fe), and low-copper LM25 (AlSi7Mg). Potential interactions between the mechanical properties of the substrate and the deposited coatings were deemed to be significant. Microstructural, microhardness, friction, and wear (pin-on-disk, microabrasion, Taber abrasion, etc.) results are reported, and the performance differences between coatings on the different substrates were noted. The …