Materials Science and Engineering Commons^™

Estimation Of Transient Temperature Distribution During Quenching, Via A Parabolic Model, Diego E. Lozano, Gabriela Martinez-Solis, Rafael David Mercado-Solis, Rafael Colás, George E. Totten

Mechanical and Materials Engineering Faculty Publications and Presentations

A material-independent model to estimate the transient temperature distribution in a test probe quenched by immersion is presented in this study. This model is based on the assumption that, under one-dimensional unsteady heat conduction, the radial temperature distribution at the end of an interval belongs to the equation of a parabola. The model was validated using AISI 304 stainless steel test probes (Φ8×40 mm and Φ12×60 mm) quenched from 850 to 900 °C in water and in water-based NaNO2 solutions at 25 °C and in canola oil at 50 °C. Additionally, square test probes (20×20×100 mm) were quenched from 550 …

Influence Of Resonant And Non-Resonant Vibrational Excitation Of Ammonia Molecules In Gallium Nitride Synthesis, Hossein Rabiee Golgir, Yunshen Zhou, Kamran Keramatnejad, Yongfeng Lu

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Attempts on the selective promotion of gallium nitride (GaN) growth were investigated by deploying laserassisted vibrational excitation of reactant molecules, which deposits energy selectively into specific molecules and activate the molecules towards the selected reaction pathways. Laser-assisted metal organic chemical vapor deposition (LMOCVD) of GaN was studied using a wavelength-tunable CO2 laser. The NH-wagging modes (υ2) of ammonia (NH3) precursor molecules are strongly infrared active and perfectly match the emission line of the CO2 laser at 9.219, 10.350, and 10.719 μm. On- and off-resonance excitations of molecules were performed via tuning the incident laser wavelengths at on-resonant wavelength 9.219 μm …

Evaluation Of Nickel-Titanium Oxide-Niobium Pentoxide Metal Ceramic Composite As Interconnect For Solid Oxide Fuel Cell, Abhijith Budur

Masters Theses

"With increasing importance for clean energy, fuel cells have gained great significance in recent decades. Solid oxide fuel cells are easy to transport due to presence of solid electrolyte and also have requisite electrical properties,but have been obstructed by their limitation to be used at only temperatures greater than 600⁰C and less than 800⁰C. To construct a stack of cells, materials that are good electrical conductors and having necessary mechanical strengths at that temperatures are being considered as interconnects between the cells. Evaluation of Nickel-Titanium dioxide-Niobium pentoxide (NTN) as interconnect and comparison to Stainless Steel 441 alloy has been made …

Formation And Evolution Of Spinel In Aluminum Killed Calcium Treated Linepipe Steels, Obinna Adaba

Masters Theses

"Magnesium aluminate (Spinel) inclusions have been observed to cause hook crack in line pipe steels. These inclusions are typically formed during liquid steel processing at the ladle metallurgy furnace (LMF) and subsequently modified by calcium to form less harmful liquid inclusions. Unfortunately, spinel inclusions are still sometimes observed in samples taken from the tundish and coil after calcium treatment.

The formation and evolution of spinel inclusions during liquid steel processing at two industrial mini mills was investigated by analysis of lollipop samples taken at different stages of the steelmaking process. The effect of reoxidation on the formation of spinels after …

Developing A Novel Methodolgy And Testbed For Fatigue Analysis Of Metal Specimens, Sai Aravind Palepu

Masters Theses

"A prototype of fatigue testing machine was built to determine the fatigue strength of materials. Proposed testing prototype was displacement controlled magnetic type bend fatigue testing machine. Designed prototype was tuned to operate at or near resonance of the specimen in order to amplify excitation displacement. Low maintenance i.e. zero wear of the parts was achieved, there were no moving components in the prototype machine. Crucial components used to build were: DC power supply, solenoid, Arduino UNO, supports and laser displacement sensor. DC source used to pass current through solenoid producing magnetic field; mosfet and Arduino generated square waves of …

Investigation Of Lanthanide-Doped Anatase Tio2 Core-Shell Nanoparticles For Photocatalysis And Gas Sensing, Rezwanur Rahman

Graduate Theses/Dissertations

Anatase TiO2 has been shown to be potential applications for photo-remediation of chemical waste as well as for photocatalytic splitting of water. The catalytic properties of TiO2 materials can be modified by doping with lanthanide (Ln) ions. In order to minimize the distortion and/or change of the structure of TiO2 nanoparticles, surface doping of anatase TiO2 nanoparticles (~ 14 nm) with several Ln ions (Nd3+, Gd3+, Eu3+, Yb3+) has been successfully made. X-ray diffraction (XRD) and Raman characterization shows that the anatase phase of treated nanoparticles is well preserved. Scanning electron microscopy (SEM) shows that the majority of the nanoparticles …

Novel Engineered Nanomaterials For Water Remediation And Gas Adsorption: Graphene Oxide And Carbon Nanotubes Decorated With Metal-Organic Frameworks And Magnetic Nanoparticles, Vahid Jabbari

Open Access Theses & Dissertations

In the current study, a series of novel magnetic and non-magnetic hybrid nanocomposites based on metal-organic frameworks (MOFs) of M3(BTC)2 (M: Ni, Cu, Zn, and Cd), graphene oxide (GrO), and carbon nanotubes (CNTs), and Fe3O4 magnetic nanoparticles (MNPs) were developed via a green, simple and versatile solvothermal method at which GrO and CNT were used as platform to grow the MOFs and Fe3O4 MNPs over them. The as-synthesized nanocomposites were characterized by XRD, SEM, TEM, XPS, IR, Raman, TGA, and N2 adsorption/desorption isotherms. Morphological analysis confirmed successful growth of nano-size Fe3O4 MNPs and M3(BTC)2 MOFs over GrO and CNT platforms. …

A Methodology For Use Of Digital Image Correlation For Hot Mix Asphalt Testing, Estefany Ramos

Open Access Theses & Dissertations

Digital Image Correlation (DIC) is a relatively new technology which aids in the measurement of material properties without the need for installation of sensors. DIC is a noncontact measuring technique that requires the specimen to be marked with a random speckled pattern and to be photographed during the test. The photographs are then post-processed based on the location of the pattern throughout the test. DIC can aid in calculating properties that would otherwise be too difficult even with other measuring instruments.

The objective of this Thesis is to discuss the methodology and validate the use of DIC in different hot …

Processing And Property Evaluation Of Tungsten-Based Mixed Oxides For Photovoltaics And Optoelectronics, Mirella Vargas

Open Access Theses & Dissertations

Tungsten Oxide (WO3) films and low-dimensional structures have proven to be promising candidates in the fields of photonics and electronics. WO3 is a well-established n-type semiconductor characterized by unique electrochromic behavior, an ideal optical band gap that permits transparency over a wide spectral range, and high chemical integrity. The plethora of diverse properties endow WO3 to be highly effective in applications related to electrochromism, gas sensing, and deriving economical energy. Compared to the bulk films, a materials system involving WO3 and a related species (elements or metal oxides) offer the opportunity to tailor the electrochromic response, and an overall enhancement …

An Improved Sin-Hyperbolic Constitutive Model For Creep Deformation And Damage, Mohammad Shafinul Haque

Open Access Theses & Dissertations

Inspection and maintenance of industrial gas turbines (IGTs) cost millions of dollars. Growing demand of obtaining higher IGT efficiency leads to higher temperature and pressure operating conditions. Long exposure of turbine components at elevated temperature and pressure

makes creep damage critically important to consider during planning, designing and operating conditions. Effective and economic maintenance requires accurate creep deformation, damage

evolution and rupture life prediction information. Creep prediction models are used to determine the state of the turbine components and to schedule the inspection, maintenance and replacement time periods. The more accurate the prediction model, the less is the overall cost …

Transition Metal Carbide (Tmc) Novel Materials For Novel Catalytic Applications, Svetlana Lagoykina

Open Access Theses & Dissertations

Transition metal carbides (TMC) constitute a diverse class of materials and traditionally have many technological applications. TMC became a subject of extensive research since 1973, when their platinum -like properties were discovered. They demonstrated high catalytical activity and selectivity in a variety of chemical reaction and have potential for some novel catalytic application.

This research is an effort to design new high effective, selective and stable bimetal or alkali promoted TMC catalyst. After extensive theoretical research a wide range of TMC, including bimetal and alkali promoted carbides, were synthesized by different methods. All solids were characterized by XRD and microscopy. …

Thermal Shock Studies On Carbon-Carbon Composites: Experimentation And Analysis, Alma Lucia Leanos

Open Access Theses & Dissertations

The oxidation behavior of C/C composites under thermal shock conditions in air is understood and predicted experimentally and by computational efforts. In Chapter. 1, both compressive properties and oxidation behavior of pristine and thermal shock exposed 2D C/C composite specimens were examined. Pristine test specimens were exposed to thermal shock conditions with temperatures ranging from 400°C to 1000°C in an oxidizing environment, followed by compression tests on pristine and thermal shock exposed specimens to obtain their compressive responses.

Similarly, in Chapter. 2, the influence of thermal shock conditions on both, the extent of carbon materials decomposition and the through-thickness compressive …

Failure Modes For I-Section Gfrp Beams, Mamadou Konate, Zia Razzaq

Civil & Environmental Engineering Faculty Publications

This paper presents calculations for the failure modes for I-section Glass Fiber Reinforced Polymer (GFRP) beams with single mid-span web brace. Theoretical predictions are made using ASCE-LFRD Pre-Standard for FRP structures. For the member length considered, it is found that for small and medium I-sections the failure mode is governed by lateral-torsional buckling and for bigger I-sections the failure mode is governed by material rupture. The outcome of the predicted lateral-torsional buckling mode is compared with that observed experimentally.

Reconfigurable Solid-State Dye-Doped Polymer Ring Resonator Lasers, Hengky Chandrahalim, Xudong Fan

Faculty Publications

This paper presents wavelength configurable on-chip solid-state ring lasers fabricated by a single-mask standard lithography. The single- and coupled-ring resonator hosts were fabricated on a fused-silica wafer and filled with 3,3′-Diethyloxacarbocyanine iodide (CY3), Rhodamine 6G (R6G) and 3,3′-Diethylthiadicarbocyanine iodide (CY5)-doped polymer as the reconfigurable gain media. The recorded lasing threshold was ~220 nJ/mm² per pulse for the single-ring resonator laser with R6G, marking the lowest threshold shown by solid-state dye-doped polymer lasers fabricated with a standard lithography process on a chip. A single-mode lasing from a coupled-ring resonator system with the lasing threshold of ~360 nJ/mm² per pulse …

The Future Of Carbon-Based Scaffolds In Foot And Ankle Surgery, Jarema S. Czarnecki, Khalid Lafdi, Panagiotis A. Tsonis

Chemical and Materials Engineering Faculty Publications

Autologous grafts have been the gold standard in tissue replacement and the most accurate means of recapitulating both the biological and mechanical properties of tissue. However, autologous grafts have had complications and drawbacks. Skin grafting, a prime example of an autologous tissue graft, has been limited by the size of graft, availability, and secondary donor site morbidity. Use of cadaveric tissues circumvents several limitations of autologous grafts; however, sterilization processes used to reduce the risk of disease transmission potentially weaken tissues and eliminate living cells and some growth factors from scaffolds, making them suboptimal tissue replacements. Chemical cross-linkage of tissue …

The Ph Sensing Properties Of Rf Sputtered Ruo2 Thin-Film Prepared Using Different Ar/O2 Flow Ratio, Ali Sardarinejad, Devendra Kumar Maurya, Kamal Alameh

Research outputs 2014 to 2021

The influence of the Ar/O₂ gas ratio during radio frequency (RF) sputtering of the RuO₂ sensing electrode on the pH sensing performance is investigated. The developed pH sensor consists in an RF sputtered ruthenium oxide thin-film sensing electrode, in conjunction with an electroplated Ag/AgCl reference electrode. The performance and characterization of the developed pH sensors in terms of sensitivity, response time, stability, reversibility, and hysteresis are investigated. Experimental results show that the pH sensor exhibits super-Nernstian slopes in the range of 64.33-73.83 mV/pH for Ar/O₂ gas ratio between 10/0-7/3. In particular, the best pH sensing performance, in …

Seeing Red: Characterizing Historic Bricks At Sylvester Manor, Long Island, Ny 1652-1735, Martin John Schmidheiny

Graduate Masters Theses

The goal of this project is to develop a basic material characterization of the bricks excavated at the site of Sylvester Manor on Shelter Island, New York. In the early Manor period of 1650-1690, this early Northern provisioning plantation supplied Barbadian sugar operations and pursued mercantile interests independent of state control. Accounting for the range of production defects and material characteristics of the bricks suggests on-site or local manufacture as a regional ceramic industry developed. Qualitative visual analysis and petrographic thin-sections were used to characterize the internal composition, variation and production evidence in the bricks. Interpreting the results of this …

Congenital Epidermoid Cyst Results In Muscle Fusion Defect In The Upper Lip, Fatih Dogan, Ibrahim Hakan Bucak

Materials Science and Engineering Faculty Research & Creative Works

Epidermoid cysts are rarely detected malformations in the oral cavity. Their development sites are the sublingual, submaxillary, and submandibular spaces. In this paper, we report a three-month-old infant who was admitted to our hospital due upper lip swelling. Magnetic resonance imaging showed that she had a two-centimeter cystic lesion and fusion defects of orbicularis oris muscle. The cyst was surgically removed, and histopathological diagnosis was “epidermoid cyst.” In recent literature, we could not find reports related to orbicularis oris muscle fusion defects because of epidermoid cyst.

Sulfur Vacancies In Photorefractive Sn2P2S6 Crystals, Eric M. Golden, Sergey A. Basun, A. A. Grabar, I. M. Stoika, Nancy C. Giles, D. R. Evans, Larry E. Halliburton

Faculty Publications

A photoinduced electron paramagnetic resonance (EPR) spectrum in single crystals of Sn2P2S6 (SPS) is assigned to an electron trapped at a sulfur vacancy. These vacancies are unintentionally present in undoped SPS crystals and are expected to play an important role in the photorefractive behavior of the material. Nonparamagnetic sulfur vacancies are formed during the initial growth of the crystal. Subsequent illumination below 100 K with 442 nm laser light easily converts these vacancies to EPR-active defects. The resulting S = 1/2 spectrum shows well-resolved and nearly isotropic hyperfine interactions with two P ions and two Sn ions. Partially resolved interactions …

Platinum Hollow Nanospheres With Different Sizes: Controllable Synthesis And Electrocatalytic Oxidation Toward Methanol, Xuan Lin, Mei-Qin Cheng, Zhong-Jin Shang, Ting Xiong, Xian-Tu Zhang, Wei Tian, Jian-Yun Lin, Qi-Ling Zhong, Bin Ren

Journal of Electrochemistry

The selenium (Se) templates and hollow platinum (Pthollow) nanospheres with different sizes were controllably synthesized by adjusting the concentration of sodium dodecyl sulphonate (SDSN) (CSDSN, μmol·L-1) which was used as a surfactant. Accordingly, the Pthollow nanospheres modified glassy carbon (GC) electrode (Pthollow/GC) was prepared. The morphology and composition of Pthollow nanospheres were characterized by scanning electron microscopy (SEM), transmission electron microscope (TEM), energy dispersive X-ray spectroscopy (EDX), high resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED) and X-ray diffraction (XRD) techniques. The electrocatalytic activities of Pthollow/GC and electrodeposited Pt nanoparticles modified glassy carbon electrode (Ptnano/GC) toward methanol oxidation …