Materials Science and Engineering Commons^™

High Frequency Signal Transmission In Through Silicon Via Based 3d Integrated Circuit, Min Xu

Legacy Theses & Dissertations (2009 - 2024)

Through silicon vias (TSVs) enable 3-dimensional (3D) integrated circuits (ICs), which have the potential to reduce the power consumption, interconnect length and overall communication latency in modern nanoelectronics systems. High-speed signal transmission channels through stacked silicon substrates are critical for 3D heterogeneous integration. This work presents systematic analyses of fabricated 3D IC test structures. This includes test structure design, fabrication, experimental characterization, equivalent circuit modeling and full wave simulations for high-speed signal transmission of the TSV based 3D IC channels.

The Impact Of Seed Layer Structure On The Recrystallization Of Ecd Cu And Its Alloys, Brendan B. O'Brien

Legacy Theses & Dissertations (2009 - 2024)

Despite the significant improvements originally offered by the use of Cu over Al as the interconnect material for semiconductor devices, the continued down-scaling of interconnects has presented significant challenges for semiconductor engineers. As the metal line widths shrink, both the conductivity and reliability of lines decrease due to a stubbornly fine-grained microstructure in narrow lines.

Carbon 1d/2d Nanoelectronics : Integration And Device Applications, Zhaoying Hu

Legacy Theses & Dissertations (2009 - 2024)

Graphene is a one-atom thick planar monolayer of sp2-bonded carbon atoms organized in a hexagonal crystal lattice. A single walled carbon nanotube (CNT) can be thought of as a graphene sheet rolled up into a seamless hollow cylinder with extremely high length-to-diameter ratio. Their ultra-thin body, large surface area, and exceptional electronic, optical and mechanical properties make these low-dimensional carbon materials ideal candidates for electronic applications. However, adopting low-dimensional carbon materials into semiconductor industry faces significant material and integration challenges. There is an urgent need for research at fundamental and applicative levels to find a roadmap for carbon nanomaterial to …

Design And Development Of Stress Engineering Techniques For Iii-Nitride Epitaxy On Si, Jeff Leathersich

Legacy Theses & Dissertations (2009 - 2024)

III-Nitrides have been a heavily researched material system for decades. Their material properties are favorable for a number of applications, most commonly in the optoelectronic and power device industry. Currently a majority of commercialized devices are fabricated on sapphire and SiC substrates but these are expensive and limit the widespread commercialization of the technology. There is substantial ongoing research geared toward the development of GaN on Si substrates because of the significant cost saving that would be realized through the inexpensive, large wafer and maturity of Si fabrication. Significant challenges with the deposition of GaN on Si have, thus far, …

Tunable Optical Nanocavity Of Iron-Garnet With A Buried Metal Layer, Alexey N. Kuz'michev, Lars E. Kreilkamp, Mohammed Nur-E-Alam, Evgeni Bezus, Mikhail Vasilev, Iliya A. Akimov, Kamal Alameh, Manfred Bayer, Vladimir I. Belotelov

Research outputs 2014 to 2021

We report on the fabrication and characterization of a novel magnetophotonic structure designed as iron garnet based magneto-optical nanoresonator cavity constrained by two noble metal mirrors. Since the iron garnet layer requires annealing at high temperatures, the fabrication process can be rather challenging. Special approaches for the protection of metal layers against oxidation and morphological changes along with a special plasma-assisted polishing of the iron garnet layer surface were used to achieve a 10-fold enhancement of the Faraday rotation angle (up to 10.8°=μm) within a special resonance peak of 12 nm (FWHM) linewidth at a wavelength of 772 nm, in …

Size Effects In Human Visual Inspection For Micro/Meso Scale Parts, Sri Harsha Kavuri

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Visual inspection has been a major method of quality control in conventional manufacturing processes for the last fifty years. Utilizing trained human inspectors to perform this visual inspection has been the most effective means of maintaining quality control. Extensive research has been performed to understand the factors that influence the human inspection process.

In the recent years, there has been a significant emphasis on manufacturing at the smaller end of the size-spectrum such as Micro and Meso scale manufacturing. Quality control at becomes a challenging task due to the extremely small sizes. Several automated visual inspection techniques have been proposed …

Influence Of Spatial Variations Of Railroad Track Stiffness And Material Inclusions On Fatigue Life, Celestin Nkundineza

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Railroad transportation is very important for economic growth and effective maintenance is one critical factor for its economic sustainability. The high repetitive forces from a moving railcar induce cyclic stresses that lead to rail bending and potential deterioration due to fatigue crack initiation and propagation. Previous research for prediction of fatigue life has been done under the assumptions of a uniform track bed and a homogeneous rail. However the spatial variation of the track stiffness is expected to increase the maximum stresses in the rail and, therefore, accelerate the fatigue process. The research described in this dissertation is focused on …

Deforming Diamond, Ciprian Borcea, Ileana Streinu

Computer Science: Faculty Publications

For materials science, diamond crystals are almost unrivaled for hardness and a range of other properties. Yet, when simply abstracting the carbon bonding structure as a geometric bar-and-joint periodic framework, it is far from rigid. We study the geometric deformations of this type of framework in arbitrary dimension d, with particular regard to the volume variation of a unit cell.

First-Principles Point Defect Models In Zr7ni10 And Zr2ni7 Binary Intermetallic Compounds And Their Implications In Nickel-Metal Hydride Batteries, Diana Felicia Wong

Wayne State University Theses

Zr-Ni-based alloys as nickel-metal hydride battery anode materials offer low-cost, flexible and tunable battery performance. Zr7Ni10 is an important secondary phase found in multi-phased AB2 Laves-phase-based metal hydride alloys, and the synergetic effect between the Zr-Ni and the Laves phases allows access to the high hydrogen storage of the Zr-Ni phases despite the lower absorption/desorption kinetics. Zr7Ni10 displays a small solubility window for Zr-rich compositions, while Zr2Ni7, with no solubility window, shows poor capacity with good kinetics. Stability of point defects within the crystal structure allows Zr7Ni10 to maintain the same structure at off-stoichiometric compositions, thus it is theorized that …

Temporally And Spatially Resolved Plasma Spectroscopy In Pulsed Laser Deposition Of Ultra-Thin Boron Nitride Films, Nicholas R. Glavin, Christopher Muratore, Michael L. Jespersen, Jianjun Hu, Timothy S. Fisher, Andrey A. Voevodin

Chemical and Materials Engineering Faculty Publications

Physical vapor deposition (PVD) has recently been investigated as a viable, alternative growth technique for two-dimensional materials with multiple benefits over other vapor deposition synthesis methods. The high kinetic energies and chemical reactivities of the condensing species formed from PVD processes can facilitate growth over large areas and at reduced substrate temperatures. In this study, chemistry, kinetic energies, time of flight data, and spatial distributions within a PVD plasma plume ablated from aboron nitride (BN) target by a KrF laser at different pressures of nitrogen gas were investigated. Time resolved spectroscopy and wavelength specific imaging were used to identify and …

Understanding Impurities In Copper Electrometallurgy, Paul Laforest

Masters Theses

"This work involves examining two industrial reports of methods to handle impurities in copper electrowinning and electrorefining. The first part evaluates the addition of Hydrostar, Cyquest N-900, DXG-F7, and Guartec EW to copper electrowinning electrolyte to affect MnO₂ deposition on coated titanium anodes (CTAs). The second part examines the effects of anode chemistry and thiourea addition on the ductility of electrorefined copper starter sheet.

In part one, a laboratory cell was used to simulate a short cycle electrowinning cell via chronopotentiometric operation with an IrO₂-Ta₂O₅ CTA at 40⁰C. A cyclic voltammetric sweep was applied …

Determination Of Setting Times By Shear Wave Velocity Evolution In Fresh Mortar Using Bender Element Method, Jianfeng Zhu

Masters Theses

This study aims at using modified bender element (BE) method to monitor the shear wave velocity (V_s) of mortar at early-age and determine initial and final setting times with the V_s method. Modifications of the traditional BE method have been made to overcome the aggressive cementitious environment and eliminate electromagnetic coupling. BE has been successfully employed in mortar samples with and without admixtures to evaluate the evolution of V_s during the early age (first 24 hrs) of hydration. An energy approach method of determining the first arrival time of S-wave has been proposed. Pulse wave velocity …

Hybrid Manufacturing Process Of SicF/Sic Composite Using Preceramic Polymer, Robert Raymond Meinders

Masters Theses

"Continuous fiber-reinforced silicon carbide (SiC_f/SiC) ceramic composites have been increasingly used due to their high temperature strength and graceful failure mechanisms. A disadvantage is the high cost and lengthy production processes that are required to develop these materials. Polymer infiltration and pyrolysis (PIP) is one of the most attractive fabrication processes for composites due to shape flexibility, mass production and relatively low cost; however, the quality of material obtained by this method has been considered insufficient due to the microstructure defects of the material obtained. This study investigated a hybrid of multiple polymer manufacturing processes to maximize quality …

Healing Of Bone Defects In A Rodent Calvarial Defect Model Using Strong Porous Bioactive Glass (13-93) Scaffolds, Yinan Lin

Masters Theses

"The main objective of this project was to evaluate the capacity of strong porous silicate (13-93) bioactive glass scaffolds prepared by a robocasting technique to regenerate bone and stimulate angiogenesis in a rat calvarial defect model. The scaffolds were created with the same grid-like microstructure but in a variety of formulations: (i) as-fabricated, (ii) pretreated in an aqueous phosphate solution to convert the glass surface to hydroxyapatite, (iii) loaded with bone morphogenetic protein-2 (BMP2) (1 µg per scaffold), and (iv) doped with copper (0.4-2.0 wt. % CuO). When compared to the as-fabricated scaffolds, the pretreated scaffolds enhanced bone regeneration at …

Engineered Fiber Reinforced Shotcrete For Efficient And Fast Ground Support Installation, N. Ginouse, S. Reny, M. Jolin

Shotcrete for Underground Support XII

No abstract provided.

Evaluation Of Wet-Mix Shotcrete Containing Set-Accelerator And Service Life Prediction, Marc Jolin, F. Melo, B. Bissonnette, P. Power, E. Demmard

Shotcrete for Underground Support XII

No abstract provided.

Transport Properties Of Wet-Mix Shotcrete, Lihe (John) Zhang, Dudley R. Morgan

Shotcrete for Underground Support XII

No abstract provided.

Comparison On Different Design Approaches Applied To A New Tunnel Lining System Reinforced By Tubular Arch, C.L. Zenti, R. Perlo

Shotcrete for Underground Support XII

No abstract provided.

New Technologies In Underground Projects: Drill Core Scanning, Documentation And Analysis, Jens Wiegand

Shotcrete for Underground Support XII

No abstract provided.

The Effect Of Spraying On Fiber Content And Shotcrete Properties, Marc Jolin, J.-D. Lemay, N. Ginouse, B. Bissonnette, É. Blouin-Dallaire

Shotcrete for Underground Support XII

No abstract provided.