Materials Science and Engineering Commons^™

The Effect Of Pore Density And Distribution On Fatigue Weak Links In An A713 Cast Aluminum Alloy, Rami A. Almatani

Theses and Dissertations--Chemical and Materials Engineering

The effects of pore density and distribution were investigated on the fatigue crack initiation behavior in an A713 sand cast aluminum alloy plate of 12 mm thickness. The applied stress- the number of cycles to failure (S-N) curves of the samples taken from 2 mm and 5 mm from the free surface were obtained using four-point bend fatigue testing at room temperature, frequency of 20 Hz, stress ratio of 0.1, sinusoidal waveform, and in ambient air. The fatigue strengths of both, the 2 mm and 5 mm samples were 60% of the yield strength (σy=171.9 MPa) of the …

Utilization Of Bio-Renewable Lignin In Building High Capacity, Durable, And Low-Cost Silicon-Based Negative Electrodes For Lithium-Ion Batteries, Tao Chen

Theses and Dissertations--Chemical and Materials Engineering

Silicon-based electrodes are the most promising negative electrodes for the next generation high capacity lithium ion batteries (LIB) as silicon provides a theoretical capacity of 3579 mAh g^-1, more than 10 times higher than that of the state-of-the-art graphite negative electrodes. However, silicon-based electrodes suffer from poor cycle life due to large volume expansion and contraction during lithiation/delithiation. In order to improve the electrochemical performance a number of strategies have been employed, such as dispersion of silicon in active/inactive matrixes, devising of novel nanostructures, and various coatings for protection. Amongst these strategies, silicon-carbon coating based composites are one …

Functionalization Of Silver Nanoparticles On Membranes And Its Influence On Biofouling, Conor G. Sprick

Theses and Dissertations--Chemical and Materials Engineering

Ultrafiltration (UF) processes are often used as pretreatment before more retentive/costly processes, such as nanofiltration and reverse osmosis. This study shows the results of low-biofouling nanocomposite membranes, loaded with casein-coated silver nanoparticles (casein-Ag-NPs). Membranes were cast and imbedded with Ag-NPs using two approaches, physical blending of Ag-NPs in the dope solution (^PAg-NP/CA membranes) and chemical attachment of Ag-NPs to cast membranes (^CAg-NP/CA membranes), to determine their biofouling control properties. The functionalization of Ag-NPs onto the CA membranes was achieved via attachment with functionalized thiol groups with the use of glycidyl methacrylate (GMA) and cysteamine chemistries. The …

Understanding And Improving Manufacturing Processes For Making Lithium-Ion Battery Electrodes, Mohanad N. Al-Shroofy

Theses and Dissertations--Chemical and Materials Engineering

Lithium-ion batteries (LIBs) have been widely used as the most popular rechargeable energy storage and power sources in today’s portable electronics, electric vehicles, and plug-in hybrid electric vehicles. LIBs have gained much interest worldwide in the last three decades because of their high energy density, voltage, rate of charge and discharge, reliability, and design flexibility. I am exploring the possibility of developing battery manufacturing technologies that would lower the cost, reduce the environmental impact, and increase cell performance and durability.

This dissertation is focused firstly on understanding the effect of mixing sequence (the order of introducing materials) and optimizing the …

Charge Transport In Electronic-Ionic Composites, Long Zhang

Theses and Dissertations--Chemical and Materials Engineering

The goal of this thesis is to generate fundamental understandings of charge transport behaviors of composites consisting of garnet structured Al substituted Li₇La₃Zr₂O₁₂ (LLZO) electrolyte and LiCoO₂ electrode. In order to take full advantage of all-solid-state batteries, bulk type composite electrodes should be introduced to increase energy and power density. However, the charge utilization of bulk type composite electrodes is quite low. Understanding ionic conduction behavior is, therefore, important for improving the performance of all-solid-state batteries, because ion conduction within solids depends on effective pathways. Electronic conductivity can be easily compensated by …

Acenes, Heteroacenes And Analogous Molecules For Organic Photovoltaic And Field Effect Transistor Applications, Devin B. Granger

Theses and Dissertations--Chemistry

Polycyclic aromatic hydrocarbons composed of benzenoid rings fused in a linear fashion comprise the class of compounds known as acenes. The structures containing three to six ring fusions are brightly colored and possess band gaps and charge transport efficiencies sufficient for semiconductor applications. These molecules have been investigated throughout the past several decades to assess their optoelectronic properties. The absorption, emission and charge transport properties of this series of molecules has been studied extensively to elucidate structure-property relationships. A wide variety of analogous molecules, incorporating heterocycles in place of benzenoid rings, demonstrate similar properties to the parent compounds and have …

The Effects Of Fiber Orientation And Volume Fraction Of Fiber On Mechanical Properties Of Additively Manufactured Composite Material, Suresh Chandra Kuchipudi

All Graduate Theses, Dissertations, and Other Capstone Projects

Additive manufacturing (AM) also known as 3D printing has tremendous advancements in recent days with a vast number of applications in industrial, automotive, architecture, consumer projects, fashion, toys, food, art, etc. Composite materials are widely used in structures with weight as a critical factor especially in aerospace industry. Recently, additive manufacturing technology, a rapidly growing innovative technology, has gained lot of importance in making composite materials. The properties of composite materials depend upon the properties of constituent’s matrix and fiber. There is lot of research on effect of fiber orientation on mechanical properties of composite materials made using conventional manufacturing …

Understanding The Intrinsic Electrochemistry Of Ni-Rich Layered Cathodes, Shawn W. Sallis

Graduate Dissertations and Theses

The demand for energy is continually increasing overtime and the key to meeting future demand in a sustainable way is with energy storage. Li-ion batteries employing layered transition metal oxide cathodes are one of the most technologically important energy storage technologies. However, current Li-ion batteries are unable to access their full theoretical capacity and suffer from performance limiting degradation over time partially originating from the cathode and partially from the interface with the electrolyte. Understanding the fundamental limitations of layered transition metal oxide cathodes requires a complete understanding of the surface and bulk of the materials in their most delithiated …

Dft Study On The Li Mobility In Li-Ion-Based Solid-State Electrolytes, Shafiqul Islam

Graduate Theses/Dissertations

I have investigated the diffusion mechanisms of Li-ion in amorphous lithium phosphite (LiPO₃) with addition of sulphur. By applying the nudge elastic band (NEB) method in crystal LiPO₃ and Li₃PO₄, I confirmed the easing of diffusion pathways for Li ion in LiPO₃ which is consistent with the previous theoretical finding[1]. From the diffusion study in 0.5 Li₂O- 0.5 P₂O₅ and 0.4 Li₂SO₄ – 0.6 (Li₂O-P₂O₅) melts above 3000K performed with ab-initio molecular dynamics (AIMD), produces identical outcome as …

Study Of Nano-Bio Interfaces In Nano-Bio Conjugates: Nanoparticles Of Zinc Oxide (Zno) And Biomolecules Of Glucose, Cytosine, And Thymine, Bithi Paul

Graduate Theses/Dissertations

Nano conjugates, composites of inorganic nanomaterials and bio molecules such as DNA, RNA and proteins, establish a sequence of wide varieties of nano-bio boundaries. The formation of these boundaries strongly depends on bio physicochemical reaction of biomolecules coated on the surface of nanomaterials. I am investigating various nano-bio conjugates consisting of zinc oxide (ZnO) nanoparticles with simple biomolecules including glucose and the nitrogenous bases of DNA such as cytosine and thymine. All nano-bio conjugates were fabricated using a standard bio-chemical synthesis process. Structural, physical, bio-chemical interface properties of nano-bio composites were probed using X-ray diffraction (XRD), Raman spectroscopy, and photoluminescence …

A Study Of Copper And Aluminum Incorporated Chromium Oxide Core-Shell Magnetic Nanoparticles, Tamzid Ibn Minhaj

Graduate Theses/Dissertations

The structural and magnetic properties of copper (Cu) and aluminum (Al) -incorporated chromium oxide (α-Cr₂O₃, i.e., chromia) inverted core-shell nanoparticles (CSNs) were investigated. The objectives of this study were to determine the role of the substituting (for chromium, Cr) element and of Cu concentration on governing the magnetic properties of the CSNs. For synthesis of the CSNs, α-Cr₂O₃ nanoparticles were first grown using microwave assisted synthesis whereupon a hydrothermal nanophase epitaxy (HNE) method was used to incorporate Cu or Al in the chromia-based shell of the nanoparticles. The morphology, structure and size characteristics …

Study Of Multiferroic Properties Of Ferroelectric- Ferromagnetic Heterostructures Bzt-Bct/Lsmo, Md Abdullah-Al Mamun

Graduate Theses/Dissertations

Currently, there has been a flurry of research focused on multiferroic materials due to their potential applications. Lead (Pb)-based ferroelectric and multiferroic materials (PZT, PMN-PT, PZN-PT etc.) have been widely used for sensors, actuators, and electro-mechanical applications due to their excellent dielectric and piezoelectric properties. However, these materials are facing global restriction due to the toxicity of Pb. In this thesis, multiferroic properties of ferroelectric-ferromagnetic heterostructures consist of Pb-free perovskite oxides 0.5Ba(Zr_0.2Ti_0.8)O₃-0.5 (Ba_0.7 Ca_0.3)TiO₃ (BZT-BCT) and La_0.7Sr_0.3MnO₃ (LSMO) have been studied. The heterostructures BZT-BCT/LSMO were …

Characterization & Extraction Of Extracellular Matrix From Porcine Adipose Tissue, Rahulkumar Kantibhia Bhoi

Open Access Theses & Dissertations

Tissue in particular extracellular matrix(ECM) plays a vital role in the growth and the function of each cell types and promote tissue regeneration and repair an impair organs. Many techniques have been developed so far to decellularized porcine tissue for the purpose to use as regenerative medicine and in tissue engineering. We aimed to optimized a method to decellularized porcine tissue while effectively eliminating xenogeneic epitopes, lipids and to retain necessary component of it intact without disrupting ECM. We have developed 2-week protocol to optimize well preserved ECM component that may keep xenogeneic biomaterial for tissue engineering and regenerative medicine. …

Structural And Electrical Characterization Of Tin Oxide Resistive Switching, Arka Talukdar

Open Access Theses & Dissertations

Resistive switching in metal oxide is a phenomenon in which the metal oxide changes its resistance upon application of electric field and thus giving two states; high resistance state (HRS) and low resistance state (LRS). Many metal oxides have been investigated however very little is known about unipolar resistive switching in SnO2 though it has shown excellent resistive switching characteristics. Defects in the material play a vital role in resistive switching of the metal oxides. In this work, the role of defects in resistive switching of SnO2 are investigated in Ti/SnO2/Au structures. Two methods were used to control the concentration …

Raman Microscopic Analysis Of Internal Stress In Boron-Doped Diamond Thin Films, Emma M.A. Sundin

Open Access Theses & Dissertations

The correlations between induced stress on undoped and boron-doped diamond (BDD) thin films, sample chemical composition, and fabrication substrate are investigated in this study via confocal Raman microspectroscopic analysis. Stability of BDD films is relevant to fast-scan cyclic voltammetry, as film delamination and dislocation of BDD-coated electrodes that can occur during neurosurgical electrode implantation can negatively impact the biosensing reliability of this technique. Electrodes were fabricated by coating cylindrical tungsten rods using a custom-built chemical vapor deposition reactor. The results of the analysis reveal a direct correlation between regions of pure diamond and enhanced material stress, as well as preferential …

Material Behavior Of Window 7 Carrier Panel Tiles And Thermal Pane Fragments Recovered From The Space Shuttle Columbia, Brenda Roseanne Arellano

Open Access Theses & Dissertations

Since the end of the space shuttle program, a new generation spacecraft has been developed to transport humans back into space. NASAâ??s Orion will carry a crew beyond low-earth orbit and the exploration of Mars may be possible in the future. Space safety becomes significant with human spaceflight and the risks are high. However, aerospace materials may provide opportunities to prevent future disasters. When the space shuttle Columbia disintegrated during re-entry in 2001, thousands of debris were collected for analysis. In contrast, when the Challenger space shuttle broke apart in 1986, all shuttle debris were buried. These tragic disasters are …

The Interplay Between Grain Size And Austenite Stability On Deformation Behavior Of High Strength-High Ductility Combination Nanostructured Stainless Steel, Venkata Sai Ananth Challa

Open Access Theses & Dissertations

The concept of phase reversion involving severe cold deformation of metastable austenite to generate strain-induced martensite, followed by temperature-time annealing sequence, was used to obtain varying grain size from nanograined/ultrafine-grained (NG/UFG) to coarse-grained (CG) regime. This concept was used to obtain â??high strength-high ductilityâ?? combination in nano/ultrafine-grained (NG/UFG) austenitic stainless steel. Using this concept, the objective of the study is to elucidate the dependence of grain size on deformation mechanisms and deformation-induced microstructural changes. The objective was accomplished by combining depth-sensing nanoindentation experiments conducted at various strain rates, and interrupted tensile testing at various strain and post-mortem analyses of deformed …

Process-Structure-Property Relationship In Magnesium-Based Biodegradable Alloy For Biomedical Applications, Pramanshu Trivedi

Open Access Theses & Dissertations

Magnesium alloys are considered to be the next generation of biomaterials because of their ability to degrade in the physiological environment. We elucidate here the impact of multiaxial forging of Mg-2Zn-2Gd alloy on grain refinement to sub-micron regime and relate the structure to mechanical properties and biological functionality. As-cast and annealed samples were multiaxial forged (MAF) for a total number of two passes with a true strain of ~2/pass. Considering that the microstructure governs the biological response of materials, we studied the constituents of the microstructure in conjunction with the mechanical behavior. The antimicrobial behavior in a Mg-2Zn-2Gd alloy with …

Electronic Structure Studies On Transition Metal Containing Endohedral Fullerenes, Carbon Onions And Zinc Sulfide Cages, Shusil Bhusal

Open Access Theses & Dissertations

We present the most stable structures for VXSc3-XN@C2n (where X=1-3 and 2n=70, 76, 78 and 80) using a systematic procedure that involves all possible isomers of the host fullerene cages. Subsequently, a detailed investigation of structural and electronic properties of the lowest energy isomers is performed using density functional theory in combination with large polarized Gaussian basis sets. The search procedure developed involved structural optimizations of thousands of fullerenes and correctly identifies the experimentally observed VSc2N@C80 and V2ScN@C80 isomer as the most stable structures. The structural analysis shows that a few V-doped endohedral fullerenes do not follow the isolated pentagon …

Mechanical Characterization Of Parts Produced By Ceramic On‐Demand Extrusion Process, Amir Ghazanfari, Wenbin Li, Ming Leu, Gregory Hilmas

Faculty Publications, Mechanical Engineering

Ceramic On‐Demand Extrusion (CODE) is an additive manufacturing process recently developed to produce dense three‐dimensional ceramic components. In this paper, the properties of parts produced using this freeform extrusion fabrication process are described. High solids loading (~60 vol%) alumina paste was prepared to fabricate parts and standard test methods were employed to examine their properties including the density, strength, Young's modulus, Weibull modulus, toughness, and hardness. Microstructural evaluation was also performed to measure the grain size and critical flaw size. The results indicate that the properties of parts surpass most other ceramic additive manufacturing processes and match conventional fabrication techniques.