Materials Science and Engineering Commons^™

Nonlinear Dielectric Behavior Of Field-Induced Antiferroelectric/Paraelectric-To-Ferroelectric Phase Transition For High Energy Density Capacitor Application, Mingyang Li

Dissertations, Master's Theses and Master's Reports

Electric field-induced antiferroelectric(AFE)/paraelectric(PE)-to-ferroelectric(FE) phase transitions are investigated for the associated nonlinear dielectric behavior, which could offer high dielectric capacity. The phenomenon in monolithic materials has been computed for Kittel antiferroelectric and BaTiO₃ model systems using the Landau-Ginzburg-Devonshire theory. The general switching curves give values of the polarization as a function of external electric field. A similar computation is performed for particle-filled polymer-matrix composites where an internal depolarization field is considered. The polarization-electric field response changes with different depolarization factors, which demonstrate the shape and alignment of the dielectric particles embedded in polymer-matrix are key factors for the composite to …

An Experimental Study Of Non-Metallic Inclusions Precipitation And Its Effect On Impact Toughness Variations In Low Alloy Steel Subjected To Complex Deoxidation, Pavel Bizyukov

Dissertations and Theses @ UNI

A low level of non-metallic inclusions in steel is the key requirement in the concept of clean steel. Although the concept has received its name quite recently, it has been implemented at the large-scale steel mills for more than 40 years. Production of clean steel became possible due active development and adoption of the post-melting treatment of molten metal in the teeming ladle. Ladle metallurgy, an umbrella term for various methods of treatment, includes operations that cannot be performed during primary metallurgical processes such as melting in an electric arc, basic oxygen, or air induction furnace. Initially, the most common …

Imaging Of Super-Fast Dynamics And Flow Instabilities Of Superconducting Vortices, L. Embon, Y. Anahory, Ž L. Jelić, E. O. Lachman, Y. Myasoedov, M. E. Huber, G. P. Mikitik, A. V. Silhanek, M. V. Milošević, A Gurevich, E. Z. Zeldov

Physics Faculty Publications

Quantized magnetic vortices driven by electric current determine key electromagnetic properties of superconductors. While the dynamic behavior of slow vortices has been thoroughly investigated, the physics of ultrafast vortices under strong currents remains largely unexplored. Here, we use a nanoscale scanning superconducting quantum interference device to image vortices penetrating into a superconducting Pb film at rates of tens of GHz and moving with velocities of up to tens of km/s, which are not only much larger than the speed of sound but also exceed the pair-breaking speed limit of superconducting condensate. These experiments reveal formation of mesoscopic vortex channels which …

Phase Stability In Cobalt-Based L12 Quaternary Intermetallics From Density Functional Theory, William Earwood

Electronic Theses and Dissertations

The effects of higher order alloying additions (Mo, Ti, Ta, Hf, Fe, V) on the phase stability of L12 (γ’) intermetallics have been studied via first-principles. A 32 atom special-quasi-random structure was used to mimic the experimentally observed solid solution sublattice. Density of states distributions were generated in order to directly observe the impact of alloying additions on the position of the pseudogap and number of states at the Fermi level. Charge density differences across the supercell were visualized to analyze changes in bonding behavior. The results indicate that substitutions of Ti, Ta, and Hf in place of the central …

Band Gap Engineering Of Titania Systems Purposed For Photocatalytic Activity, Cameron Robert Thurston

Electronic Theses and Dissertations

Ab initio computer aided design drastically increases candidate population for highly specified material discovery and selection. These simulations, carried out through a first-principles computational approach, accurately extrapolate material properties and behavior. Titanium dioxide (tio2) is one such material that stands to gain a great deal from the use of these simulations. In its anatase form, titania (tio2) has been found to exhibit a band gap nearing 3.2 ev. If titania is to become a viable alternative to other contemporary photoactive materials exhibiting band gaps better suited for the solar spectrum, then the band gap must be subsequently reduced. To lower …

Biomaterials Approaches For Utilizing The Regenerative Potential Of The Peripheral Nerve Injury Microenvironment, Melissa Renee Wrobel

Wayne State University Dissertations

Clinically available treatments are insufficient to achieve full functional recovery in large (>3cm) peripheral nerve injuries (PNI). The objectives in this thesis were 1) to study often overlooked elements of intrinsic PNI repair including release of inhibitory CSPGs and post-injury responses of inflammatory macrophages and dedifferentiated Schwann cells; 2) to create biomaterial scaf-folds featuring topographical and adhesive cues to enhance neurite outgrowth; and 3) to test the ability of those cues to direct macrophages and Schwann cells towards a pro-regenerative phe-notype. It is hypothesized that recapitulating the positive and negative cues of the PNI microenvi-ronment can better improve regeneration. …

Thermal Analysis Of 3d Printed 420 Stainless Steel, Adithya Pothuri

All Graduate Theses, Dissertations, and Other Capstone Projects

Additive manufacturing opens new possibilities in the manufacturing industry. 3D printing is a form of additive manufacturing. 3D printers will have a significant influence over the industrial market, with extremely positive effects in no time. The main aim of this research is to determine the effect of process parameters of Binder Jet manufactured 420 Stainless Steel (420SS) parts on thermal properties such as thermal conductivity. Different parameters, such as layer thickness, sintering time and sintering temperature were varied. A full factorial design of experiment matrix was made by varying these parameters using two levels. Testing showed that different parameters affected …

Processing And Properties Of Wc-Based Cu-Ni-Mn-Zn Metal Matrix Composites Produced Via Pressureless Infiltration, Paul M. Brune

Masters Theses

"This research focuses on the processing and properties of tungsten carbide-based (WC-based) Cu-Ni-Mn-Zn metal matrix composites (MMCs) fabricated by pressureless infiltration. The first goal of this project was to test the wettability of Cu-Ni-Mn and Cu-Ni-Mn-Zn on various carbides. The sessile drop technique was employed to determine if they were suitable candidates for pressureless infiltration. The carbides investigated were TaC, WC, B₄C, and SiC. It was determined that both alloys had contact angles of less than 70⁰ on TaC, WC, and B4C, which is one requirement for pressureless infiltration. However, both alloys reacted with B₄C to …

Mold Flux Crystallization And Mold Thermal Behavior, Elizabeth Irene Peterson

Masters Theses

"Mold flux plays a small but critical role in the continuous casting of steel. The carbon-coated powder is added at the top of the water-cooled copper mold, over time it melts and infiltrates the gap between the copper mold and the solidifying steel strand. Mold powders serve five primary functions: (1) chemical insulation, (2) thermal insulation, (3)lubrication between the steel strand and mold, (4) absorption of inclusions, and (5)promotion of even heat flux. All five functions are critical to slab casting, but surface defect prevention is primarily controlled through even heat flux. Glassy fluxes have high heat transfer and result …

Evaluation Of Non-Chromate Passivations On Electroplated Γ-Phase Zinc Nickel, Steven Michael Volz

Masters Theses

"This research focused on the corrosion response and electrochemical behavior of electroplated low hydrogen embrittlement alkaline γ-phase zinc nickel with passivation layers. The motivation was the need to replace hexavalent chromium conversion coatings in military grade electrical systems with a more environment friendly alternative. The passivation layers were employed for the purpose of mitigating corrosion attack while maintaining low contact resistance. Trivalent chromium-based passivations and cerium-based passivations were compared against the currently used hexavalent chromium conversion coating. The coating systems were compared using electrochemical impedance spectroscopy, cyclic potentiodymanic scans, salt spray exposure testing, electrical resistance measurements, microstructure analysis, and compositional …

Cathodic Protection Measurement Through Inline Inspection Technology Uses And Observations, Briana Ley Ferguson

Masters Theses

"This research supports the evaluation of an impressed current cathodic protection (CP) system of a buried coated steel pipeline through alternative technology and methods, via an inline inspection device (ILI, CP ILI tool, or tool), in order to prevent and mitigate external corrosion. This thesis investigates the ability to measure the current density of a pipeline's CP system from inside of a pipeline rather than manually from outside, and then convert that CP ILI tool reading into a pipe-to-soil potential as required by regulations and standards. This was demonstrated through a mathematical model that utilizes applications of Ohm's Law, circuit …

In-Situ Control Of Substrate Temperature In Additive Manufacturing To Homogenize Micro-Hardness Of Laser Clad Deposits Using Thermo-Electric Cooling, Raghu Ram Kolla

Masters Theses

”Nickel hard-surfacing alloys are replacing hard Chromium coatings due to their excellent wear and corrosion-resistant properties. In laser cladding of these alloys, however, these properties can vary across the height of the deposit due to an accumulation of excess heat generated in the deposit during the process. This may result in uneven wear of the clad parts which can be detrimental for practical purposes. The research objective is to develop an in-situ cooling system that works in line with the laser deposition system to extract the excess heat buildup and reduce the variation in the hardness of the Ni-based clad …

An Investigation Of Borax For Sealing Inflow From Berea Sandstone, Tri-Tris Bao Nguyen

Masters Theses

"Well inflow control is a major challenge for the oil and gas industry. Erle Haliburton revolutionized well inflow control with his patent for cementing oil wells in 1921. Soon after, cement became the accepted material to establish well integrity and has been ever since. Cement is used in all phases of the well life cycle, and it is expected to hold indefinitely once set. Yet based on the nature of cement and the placement techniques, flow pathways may develop from improper cementing jobs or from cement degradation over time. Well integrity is especially crucial for wellbore plugging and abandonment, since …

Overview Of Co₂ Leakage Problems And Sealants For Co₂ Leakage Remediation, Shudai Peng

Masters Theses

"Excessive Carbon Dioxide (CO₂) emission has become a serious issue and caused lots of environmental problems. Carbon Capture and Storage (CCS) program has been developed to reduce the CO₂ content in the atmosphere. CO₂ storage has been targeted mainly on depleted oil or gas reservoirs and deep saline aquifers. However, leakage could occur through wellbores, cap rocks, formation faults, and fractures during and after CO₂ injection. To minimize the risk, different types of sealants have been investigated to prevent CO₂ leaks. The aim of this thesis is to provide a comprehensive review of the materials which could be used as …

Quality Assessment Of Adhesive Bond Based On Dielectric Properties, Muthu Ram Prabhu Elenchezhian, Vamsee Vadlamudi, Priyanshu Kumar Banerjee, Chaitanya Dave, Anik Mahmood, Rassel Raihan

Institute of Predictive Performance Methodologies (IPPM-UTARI)-Archive

Composite materials are widely used in Aerospace, Marine and Automotive structures to reduce weight and increase performance. Adhesive bonding improves the stress distribution between the composite materials / dissimilar materials and ensures a lighter structure than conventional fastener joints. But still there is not much research on the Non-Destructive strength estimation and life prediction, or the damage prognosis of the adhesive bond. One of the main problems when using adhesive bonding is a "kissing bond" which is a weak adhesion bond alternatively called zero volume disbond. Typically, convectional non-destructive methods cannot detect this kissing bond. Broadband Dielectric Spectroscopy, BbDS, is …

Carbon Nanotube (Cnt) Metallic Composite With Focus On Processing And The Resultant Properties, Md Muktadir Billah

Electronic Theses and Dissertations

Metal-carbon nanotubes (CNTs) composites are the promising advanced materials that are being developed to take the advantage of the exceptional properties of CNTs. Because of the intrinsically strong in-plane atomic SP2 bonding CNTs offer high young's modulus (1.0–1.8 TPa), high tensile strength (30–200 GPa) and high elongation at break (10–30%). The thermal conductivity of individual single-walled carbon nanotube (SWCNT) and multi-walled carbon nanotube (MWCNT) are about 6000 W/m-K and 3000 W/m-K, respectively. Therefore it is expected that by incorporation of CNTs in metal matrices multi-functional composites can be used ideally as thermal interface materials, light-weight high-strength structural materials, electric components, …

Enhanced Handheld Engine Ethanol Study, Charindu Kariyawasan Jalath Thanthree

All Graduate Theses, Dissertations, and Other Capstone Projects

This study examined consumer and professional grade handheld engines. Twenty-four consumer grade 50 hour Emissions Determination Period (EDP) trimmers and 24 professional grade 300 hour EDP backpack leaf blowers were run on four different ethanol fuel concentrations; E0, E10, E15, and E20. Six engines of each type were run on each of the fuel blends through their full EDP.

All engines were broken-in and adjusted to manufacturer specifications on E0. Then engines were emissions tested on E0 to provide a baseline and to determine the rich to lean order of the engines. Next, the leanest operating engine received E20 and …

Synthesis And Characterization Of Poly(Simvastatin) - Incorporated Copolymers And Blends For Bone Regeneration, Theodora Asafo-Adjei

Theses and Dissertations--Biomedical Engineering

Common biodegradable polyesters such as poly(lactic acid) (PLA), poly(lactic-co-glycolic acid) (PLGA) and poly(ε-caprolactone) (PCL) are used as drug delivery vehicles for tissue regenerative applications. However, they are typically bioinert, with drug loading limitations. Polymerizing the active agent or precursor into its respective biodegradable polymer would control drug loading via molar ratios of drug to initiator used for synthesis. Simvastatin was chosen due to its favorable anti-inflammatory, angiogenic, and osteogenic properties. In addition, its lactone ring lends itself to ring-opening polymerization and, consequently, the synthesis of poly(simvastatin) with controlled simvastatin release.

Simvastatin was first polymerized with a 5kDa methyl-terminated poly(ethylene glycol) …

Tunable Nanocomposite Membranes For Water Remediation And Separations, Sebastián Hernández Sierra

Theses and Dissertations--Chemical and Materials Engineering

Nano-structured material fabrication using functionalized membranes with polyelectrolytes is a promising research field for water pollution, catalytic and mining applications. These responsive polymers react to external stimuli like temperature, pH, radiation, ionic strength or chemical composition. Such nanomaterials provide novel hybrid properties and can also be self-supported in addition to the membranes.

Polyelectrolytes (as hydrogels) have pH responsiveness. The hydrogel moieties gain or lose protons based on the pH, displaying swelling properties. These responsive materials can be exploited to synthesize metal nanoparticles in situ using their functional groups, or to immobilize other polyelectrolytes and biomolecules. Due to their properties, these …

Effect Of Interlayers On Mechanical Properties And Interfacial Stress Transfer Of 2d Layered Graphene-Polymer Nanocompsites, Colton C. Roach

Theses and Dissertations--Mechanical and Aerospace Engineering

Graphene, a monolayer of sp²-hybridized carbon atoms arranged in a two-dimensional (2D) lattice, is one of the most important 2D nanomaterials and has attracted tremendous attentions due to its unique geometric characteristics and exceptional mechanical properties. One of the most promising applications of this 2D nanomaterial is in polymer nanocomposites, in which the ultra-stiff, ultra-thin graphene layers function as reinforcement fillers. However, two significant questions remain to be answered: (1) whether the mechanical behaviors of 2D graphene reinforced nanocomposites can be analyzed by the convention composite theory, which is developed primarily for one-dimensional (1D) fiber-type of fillers, and …