Materials Science and Engineering Commons^™

Nanowire-Based Light-Emitting Diodes: A New Path Towards High-Speed Visible Light Communication, Mohsen Nami

Physics & Astronomy ETDs

Nano-scale optoelectronic devices have gained significant attention in recent years. Among these devices are semiconductor nanowires, whose dimeters range from 100 to 200 nm. Semiconductor nanowires can be utilized in many different applications including light-emitting diodes and laser diodes. Higher surface to volume ratio makes nanowire-based structures potential candidates for the next generation of photodetectors, sensors, and solar cells. Core-shell light-emitting diodes based on selective-area growth of gallium nitride (GaN) nanowires provide a wide range of advantages. Among these advantages are access to non-polar m-plane sidewalls, higher active region area compared to conventional planar structures, and reduction of threading …

Two Dimensional Layered Materials And Heterostructures, A Surface Science Investigation And Characterization, Yujing Ma

USF Tampa Graduate Theses and Dissertations

The isolation of single layers of van der Waals materials has shown that their properties can be significantly different compared to their bulk counterparts. These observations, illustrates the importance of interface interactions for determining the materials properties even in weakly interacting materials and raise the question if materials properties of single layer van der Waals materials can be controlled by appropriate hetero-interfaces. To study interface effects in monolayer systems, surface science techniques, such as photoemission spectroscopy and scanning probe microscopy/spectroscopy, are ideally suited. However, before these characterization methods can be employed, approaches for the synthesis of hetero-van der Waals systems …

Orientation Dependent Compression Behavior Of Co35Ni35Al30 Single Crystals, Peizhen Li, Haluk E. Karaca, Yury I. Chumlyakov

Mechanical Engineering Faculty Publications

The shape memory effect (SME) and superelasticity (SE) behavior of homogenized Co₃₅Ni₃₅Al₃₀ single crystals were systematically characterized along the [100], [110] and [111] orientations under compression. The shape memory behavior of CoNiAl was found to be highly orientation and stress/temperature dependent. Maximum compressive recoverable strains were 3.98 % in [110], 3 % in [100] and 0.30 % in [111] orientations, respectively. The Co₃₅Ni₃₅Al₃₀ demonstrated a very high superelastic temperature window of more than 350 °C along the [100] and [110] orientations. Moreover, two-way shape memory effect with very low thermal …

Development Of Starch-Polyvinyl Alcohol (Pva) Biodegradable Film: Effect Of Cross-Linking Agent And Antimicrobials On Film Characteristics, Aniket Satish More, Chandani Sen, Madhusweta Das

Journal of Applied Packaging Research

To satisfy the need of developing eco-friendly flexible antimicrobial packaging film with minimum use of synthetic chemical ingredients, the present study examined the efficacy of citric acid (CA) as cross-linking agent and essential oils (EOs), viz., cinnamon essential oil (CEO) and oregano essential oil (OEO) as natural antimicrobials in corn starch-polyvinyl alcohol (CS-PVA) film. Compared to film prepared from filmogenic solution (FS) containing 75 kg CS+8.75 kg PVA+24.6 kg glycerol per m³ FS, film additionally containing CA at 0.07 kg/kg CS indicated 95% higher ultimate tensile strength (UTS) and 27% lower water vapor permeability (WVP). Film developed with incorporation …

Impulse, Matt Schmidt, Lora Berg, Christine Delfanian, Dave Graves, Heidi Kronaizl, Emily Weber, Micayla Standish

Impulse (Jerome J. Lohr College of Engineering Publication)

[Page] 2 Better Equipped
[Page] 4 Flashback Summer Scholars
[Page] 6 Biomedical Engineering
Ryan Mahutga is the third mechanical engineering graduate in five years to receive a prestigious National Science Foundation Graduate Research Fellowship.
Nigerian native John Asiruwa is working with associate professor Stephen Gent on a mechanical engineering project to help Sanford Health build better heart stents.
Electrical engineering graduate Bruce Lutz has selected the biomedical engineering program as a target for his future giving.
[Page] 9 Programs Accredited
[Page] 10 Fast Wheels
[Page] 12 Five Unforgettable Weeks
[Page] 14 Second in the Nation
[Page] 16 Athletes and Engineering …

Nonlinear Optical Studies Of Defects And Domain Structures In Perovskite-Type Dielectric Ceramics, David J. Ascienzo

Dissertations, Theses, and Capstone Projects

In order to improve future generations of dielectric capacitors a deeper understanding of voltage-induced dielectric breakdown and electrical energy storage limitations is required. This dissertation presents the use of far-field optical second harmonic generation (SHG) polarimetry for probing structural defects and polar domains in linear and nonlinear perovskite dielectric ceramics. We investigated the formation of electric field-induced structural distortions at pristine Fe-doped SrTiO₃ (Fe:STO) electrode interfaces, structural defect and strain formation due to oxygen vacancy migration in electrodegraded Fe:STO single crystals, and mixed tetragonal and rhombohedral phase domains in ferroelectric Zr-doped BaTiO₃ (BZT) films exhibiting excellent …

Numerical Simulation For Identification Of Insects Using A Cw Lidar System, Christo Videlov

Theses

Mosquitos are the most common vector of disease in the world, causing millions of deaths a year. While curing the diseases they cause is one approach to this problem, another could be to avoid the mosquitos in the first place. Knowing their flight patterns, location, and population in one area could aid in this. Additionally, classifying the mosquitos in an area would be helpful. The age and sex of the mosquito is important to find as they affect the chances of the insect carrying diseases such as malaria or yellow fever.

Many current methodologies to monitor insects are based on …

Improving The Thermal Stability Of Cellobiohydrolase Cel7a From Hypocrea Jecorina By Directed Evolution, Frits Goedegebuur, Lydia Dankmeyer, Peter Gualfetti, Saeid Karkehabadi, Henrik Hansson, Suvamay Jana, Vicky Huynh, Bradley R. Kelemen, Paulien Kruithof, Edmund A. Larenas, Pauline J. M. Teunissen, Jerry Ståhlberg, Christina M. Payne, Colin Mitchinson, Mats Sandgren

Chemical and Materials Engineering Faculty Publications

Secreted mixtures of Hypocrea jecorina cellulases are able to efficiently degrade cellulosic biomass to fermentable sugars at large, commercially relevant scales. H. jecorina Cel7A, cellobiohydrolase I, from glycoside hydrolase family 7, is the workhorse enzyme of the process. However, the thermal stability of Cel7A limits its use to processes where temperatures are no higher than 50 °C. Enhanced thermal stability is desirable to enable the use of higher processing temperatures and to improve the economic feasibility of industrial biomass conversion. Here, we enhanced the thermal stability of Cel7A through directed evolution. Sites with increased thermal stability properties were combined, and …

Optimization Of The Hot Embossing Parameters And Sintering Characterization For Alumina/Berea Sandstone Sintering, Justin F. Robbins

LSU Master's Theses

The purpose of this study is to investigate the process of hot embossing on alumina based ceramics as a cost-efficient procedure for manufacturing microfluidic testing components. Alumina ceramics were used as an exploratory phase for the final objective of the project, manufacturing of Berea sandstone based ceramic samples. Previous research has shown potential in using hot embossing on Alumina based ceramics; however, complications with extrusion and micro-structure quality were observed. For this reason, the research performed aimed to produce Berea Sandstone based components by first improving upon the embossing quality of alumina ceramics.

The thesis first investigates changes in the …

The Subject Librarian Newsletter, Engineering And Computer Science, Fall 2017, Buenaventura "Ven" Basco

Libraries' Newsletters

No abstract provided.

Thermo-Stability And Active Site Structure Of Fe/N/C Electrocatalyst For Oxygen Reduction Reaction, Chi Chen, Yu-Jiao Lai, Zhi-You Zhou, Xin-Sheng Zhang, Shi-Gang Sun

Journal of Electrochemistry

The development of Fe/N/C electrocatalyst for oxygen reduction reaction (ORR) is vital for the large-scale applications of proton exchange membrane fuel cells. Understanding the active site structure will contribute to the rational design of highly active catalysts. In this study, the as-prepared Fe/N/C catalyst based on poly-m-phenylenediamine (PmPDA-FeN_x/C) catalyst with the high ORR activity was subjected to the high-temperature heat treatment again at 1000 ~1500 ^oC. The degradation of in the ORR activity of PmPDA-FeN_x/C by with various heat treatments was correlated to the change of elemental compositions, chemical states and textural properties. As the …

Electric Current Induced Flow And Electrocapillary Deformation Of Liquid Wood Alloy In Naoh Aqueous Solution, Guo-Di Zhang, Qiao-Li Lin, Jian-Hong Cheng, Rui Cao

Journal of Electrochemistry

The phenomena of the electric current induced flow and electrocapillary deformation for a liquid Wood alloy in a NaOH electrolyte were studied. Electrocapillary behaviors for the liquid Wood alloy in NaOH electrolytes by applying external low voltages were investigated. The electrode reaction (redox reaction) induced the formation or removing removal of an oxide film, and further caused the drop deformation by decreasing or increasing an interfacial tension. The same polar charge in the electric double layer would also decrease the interfacial tension. In order to maintain the stability of system, the contact area of the interface would be expanded, and …

Influence Of Typical Anions In Seawater Environments On Corrosion Behaviors Of 5083 Aluminum Alloy, Yang-Fan Tu, Li-Ming Feng, Zhi-Gang Fang, Hai-Tao Liu, Ming-Hua Jing, Yong Guan

Journal of Electrochemistry

The interaction effects of typical anions, namely, Cl^-, HCO₃^- and SO₄^2-, presented in seawater environments on corrosion resistance behaviors of AA5083 aluminum alloy have been studied. The corrosion resistances of the 5083 aluminum alloy in different simulated seawater environments were tested by factorial analysis method. The polarization curves, the corrosion potentials, corrosion current densities and the breakdown potentials were examined in different concentrations of Cl^-, HCO₃^- and SO₄^2-.The corrosion behavior was analyzed by electrochemical impedance spectroscopy (EIS). The results showed that both Cl^-,  and …

Tetrabutylammonium Hexafluorophosphate As Flame Retardant Additive For Lithium Ion Batteries, Qing Zhao, Qian Zhang, Jing-Min Fan, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

Safety issues have been attracted more and more attentions due to the wide applications of lithium ion batteries. Introducing flame retardant additives are one of the effective strategies to improve the safety of lithium-ion batteries. In this paper, the tetrabutylammonium hexafluorophosphate (TBAPF₆) as a flame retardant additive was added to the electrolyte as a flame retardant additive to enhance the safety of lithium ion batteries. The self-extinguishing time (SET) and ionic conductivities of the electrolytes with different TBAPF₆ contents were investigated. It is found that TBAPF6 dramatically reduced the flammability of the electrolyte while slightly decreasing ionic …

Electrochemical Performance Of Sodium Difluoro(Oxalato)Borate As The Additive Of Non-Aqueous Electrolytes For Sodium-Ion Batteries, Ding Zhang, Qin Zhu, Ying Wang, Cheng-Long Zhao, Shi-Bin Liu, Shou-Dong Xu

Journal of Electrochemistry

Sodium ion battery has attracted worldwide and intensive attention recently, while the adoption of electrolyte additives has been considered as one effective strategy to promote the cell performance. Within this work sodium difluoro(oxalato)borate (NaDFOB) was prepared and adopted as an additive for the general non-aqueous electrolyte formula of 1 mol·L-1 NaClO4/EC/PC (Vol: Vol=1:1), and the effects of the additive concentration on ionic conductivity and oxidization decomposition voltage were investigated in detail. In addition, the cell performance evaluated by NaNi0.5Mn0.5O2 as the cathode was also studied. It reveals that the addition of NaDFOB into the NaClO4/EC/PC electrolyte resulted in the significantly …

An Investigation Of The Synergistic Effect Between (1,3-Dioxolan-2-Ylmethyl)Triphenylphosphonium Bromide And Iodide Ion For The Corrosion Inhibition Of Zinc In Citric Acid, Saadawy M.

Journal of Electrochemistry

The effect of (1,3-Dioxolan-2-ylmethyl)-triphenylphosphonium bromide (DTPB) on the zinc corrosion in 0.5 mol·L^-1 citric acid solution was investigated at 30 ^oC using weight loss, potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) techniques. An ecofriendly bath was used for acid cleaning of zinc, which has not been widely used in literatures. The results showed that DTPB could serve as an effective inhibitor for the zinc corrosion in a citric acid solution with the inhibition efficiency of 98.9% at the DTPB concentration of 3×10^-3 mol·L^-1. A synergistic effect between DTPB and potassium iodide (KI) enhanced the inhibition …

Density Functional Investigation On Cathode/Electrolyte Interface In Solid-State Lithium Batteries, Xuelong Wang, Ruijuan Xiao, Yong Xiang, Hong Li, Liquan Chen

Journal of Electrochemistry

The rapidly expanding application of lithium ion batteries stimulates research interest on energy storage devices with higher energy density, better safety and faster charge/discharge speed. All-solid-state lithium batteries have been considered as promising candidates because of their fewer side reactions and better safety compared with conventional lithium-ion batteries with organic liquid electrolytes. Looking for well-matched electrode/electrolyte interfaces is one of the keys to ensuring good comprehensive performance of solid-state lithium batteries. In this report, with the aid of first-principles simulations, the local structure and lithium ions transportation properties of electrolyte surfaces and cathode/electrolyte interfaces are investigated. The β-Li₃PS …

A New Type Carbon Composited Molybdenum Doped Vanadium Oxide Nanowires As A Cathode Material For Sodium Ion Batteries, Guang-Rui Zhang, Li-Qiang Hu, Bao-Zhu Zhang

Journal of Electrochemistry

In recent years, the development of lithium ion batteries (LIBs) has been limited due to the insufficient lithium resource and increasing cost. As a promising candidate, sodium ion batteries (SIBs) with the similar electrochemical mechanism and lower cost than LIBs are developing rapidly. However, as a result of the larger radius of Na⁺ compared with Li⁺, the crystalline structures of the most electrode materials are damaged severely during the intercalation of Na⁺, which limits the electrochemical properties of SIBs. Thus, developing new types of electrode materials for SIBs is particularly important. Among the cathode materials, …

Effects Of Temperature On The Nucleation And Growth Mechanism Of Pbo2 Electrodeposition, Lei Wang, Juan-Qin Xue, Li-Hua Yu, Chang-Bin Tang, Qiang Bi

Journal of Electrochemistry

In order to investigate the effects of temperature on the nucleation and growth of lead dioxide (PbO₂), the in situ electrochemical depositions of PbO₂ were carried out on the glassy carbon electrode at different temperatures, namely, 25℃,35℃, 45℃, 55℃, and 65℃.The cyclic voltammetric curves, the time-current and the time-potential curves,SEM images and XRD patterns of the PbO₂ coatings deposited at different temperatures were obtained. The results showed that the PbO₂ underwent nucleation and grew at different temperatures. The 3D continuous nucleation mode of PbO₂ electrodeposition remained unchanged with the increase of temperature. However, the …

Effects Of Surface Modification Modes On Proton-Over-Vanadium Ion Selectivity Of Nafion®Membrane For Application In Vanadium Redox Flow Battery, Qing-Long Tan, Hai-Ning Wang, Shan-Fu Lu, Da-Wei Liang, Chun-Xiao Wu, Yan Xiang

Journal of Electrochemistry

The effect of surface modification modes on proton-over-vanadium ion selectivity was studied by spin-coating chitosan-Phosphotungstic Acid (PWA) as a single or double layer on Nafion membrane surface. To suppress the vanadium ions permeation through the Nafion? membrane in a vanadium redox flow battery (VRFB), the single surface-modified Nafion membrane (Nafion/chitosan-PWA)S and double surface-modified Nafion membrane (Nafion/chitosan-PWA)D demonstrated a 89.9% and 92.7% reduction of vanadium ion permeability in comparison with pristine Nafion, respectively. The (Nafion/chitosan-PWA)D exhibited betterhigher selectivity between proton and vanadium ions than the (Nafion/chitosan-PWA)S at the same layer thickness. Furthermore, the columbic efficiency for the VRFB single cell based …