Materials Science and Engineering Commons^™

Surface Area And Electrocatalytic Properties Of Feni Nanoparticles For The Oxygen Evolution Reaction (Oer), James Burrow

Chemical Engineering Undergraduate Honors Theses

Iron-nickel bimetallic electrocatalysts have recently emerged as some of the best candidates for the oxygen evolution reaction (OER) in alkaline electrolyte. Understanding the effects of composition and morphology of iron-nickel nanoparticles is crucial for optimization and enhanced electrocatalyst performance. Both physical surface area and electrochemical surface area (ECSA) are functions of morphology. In this study, four different iron-nickel nanoparticle catalysts were synthesized. The catalysts were varied based on morphology (alloy versus core-shell) and composition (low, medium, and high stabilizer concentration). Brunauer-Emmett-Teller (BET) surface area analysis was conducted on three of the synthesized iron-nickel nanoparticles using a physisorption analyzer while electrochemical …

Magnetic Studies Of Multiferroic Heterostructures, Ahmed Rayhan Mahbub

Graduate Theses/Dissertations

Multiferroic heterostructures (MHS) consisting of at least two materials with ferroic properties have been a major focus for researchers recently due to its immense potential in device applications. Almost all MHS use ferromagnetic layers making it a very important research area. In this thesis the magnetic properties of different ferromagnetic heterostructures have been investigated. Different bilayers of hard ferromagnet cobalt ferrite (CFO)-soft ferromagnet lanthanum strontium manganese oxide (LSMO) and hard ferromagnet CFO-antiferromagnet nickel oxide (NiO) were fabricated. Pulsed laser deposition technique was used to deposit the thin films on LAO and sapphire substrates. Purpose of using a hard ferromagnetic CFO …

Highly Flame Retardant And Bio-Based Rigid Polyurethane Foams Derived From Orange Peel Oil, Chunyang Zhang

Electronic Theses & Dissertations

Polyurethane is an important class of polymer which is being used for various industrial applications in the form of rigid foams, flexible foams, thermoplastic, elastomer, coating, and adhesive. Especially there is a huge market for rigid polyurethane foams for their applications as thermal insulating material in building and housing. In general, polyurethanes are prepared using polyols and diisocyanates. Most of the polyols used by industries are petrochemical based. In this project, a novel polyol from an orange peel oil-based derivative, limonene dimercaptan, was synthesized using one step photochemical thiol-ene reaction. The synthesized polyol was used to prepare flame retardant polyurethane …

Ultrasonic Nondestructive Evaluation Of Metal Additive Manufacturing., Venkata Karthik Nadimpalli

Electronic Theses and Dissertations

Metal Additive Manufacturing (AM) is increasingly being used to make functional components. One of the barriers for AM components to become mainstream is the difficulty to certify them. AM components can have widely different properties based on process parameters. Improving an AM processes requires an understanding of process-structure-property correlations, which can be gathered in-situ and post-process through nondestructive and destructive methods. In this study, two metal AM processes were studied, the first is Ultrasonic Additive Manufacturing (UAM) and the second is Laser Powder Bed Fusion (L-PBF). The typical problems with UAM components are inter-layer and inter-track defects. To improve the …

Elucidating The Effect Of Water-To-Cement Ratio On The Hydration Mechanisms Of Cement, Aida Margarita Ley-Hernandez, Jonathan Lapeyre, Rachel Cook, Aditya Kumar, Dimitri Feys

Materials Science and Engineering Faculty Research & Creative Works

The hydration of cement is often modeled as a phase boundary nucleation and growth (pBNG) process. Classical pBNG models, based on the use of isotropic and constant growth rate of the main hydrate, that is, calcium-silicate-hydrate (C-S-H), are unable to explain the lack of any significant effect of the water-to-cement (w/c) ratio on the hydration kinetics of cement. This paper presents a modified form of the pBNG model, in which the anisotropic growth of C-S-H is allowed to vary in relation to the nonlinear evolution of its supersaturation in solution. Results show that once the supercritical C-S-H nuclei form, their …

Corrosion Resistance Of Pipeline Steel With Damaged Enamel Coating And Cathodic Protection, Liang Fan, Signo Tadeu Dos Reis, Genda Chen, Michael L. Koenigstein

Materials Science and Engineering Faculty Research & Creative Works

This paper presents the first report on the corrosion resistance of pipeline steel with damaged enamel coating and cathodic protection in 3.5 wt % NaCl solution. In particular, dual cells are set up to separate the solution in contact with the damaged and intact enamel coating areas, to produce a local corrosion resistance measurement for the first time. Enamel-coated steel samples, with two levels of cathodic protection, are tested to investigate their impedance by electrochemical impedance spectroscopy (EIS) and their cathodic current demand by a potentiostatic test. Due to its glass transition temperature, the enamel-coated pipeline can be operated on …

Real-Time Object Detection And Tracking On Drones, Tu Le

Maseeh Summer Undergraduate Research Experience

Unmanned aerial vehicles, also known as drones, have been more and more widely used in recent decades because of their mobility. They appear in many applications such as farming, search and rescue, entertainment, military, and so on. Such high demands for drones lead to the need of developments in drone technologies. Next generations of commercial and military drones are expected to be aware of surrounding objects while flying autonomously in different terrains and conditions. One of the biggest challenges to drone automation is the ability to detect and track objects of interest in real-time. While there are many robust machine …

Characterization And Analysis Of Ultrathin Cigs Films And Solar Cells Deposited By 3-Stage Process, Grace Rajan, Krishna Aryal, Shankar Karki, Puruswottam Aryal, Robert W. Collins, Sylvain Marsillac

Electrical & Computer Engineering Faculty Publications

In view of the large-scale utilization of Cu(In,Ga)Se₂ (CIGS) solar cells for photovoltaic application, it is of interest not only to enhance the conversion efficiency but also to reduce the thickness of the CIGS absorber layer in order to reduce the cost and improve the solar cell manufacturing throughput. In situ and real-time spectroscopic ellipsometry (RTSE) has been used conjointly with ex situ characterizations to understand the properties of ultrathin CIGS films. This enables monitoring the growth process, analyzing the optical properties of the CIGS films during deposition, and extracting composition, film thickness, grain size, and surface roughness which …

Critical-Point Model Dielectric Function Analysis Of Wo3 Thin Films Deposited By Atomic Layer Deposition Techniques, Ufuk Kılıç, Derek Sekora, Alyssa Mock, Rafał Korlacki, Elena M. Echeverría, Natale J. Ianno, Eva Schubert, Mathias Schubert

Department of Electrical and Computer Engineering: Faculty Publications

WO₃ thin films were grown by atomic layer deposition and spectroscopic ellipsometry data gathered in the photon energy range of 0.72-8.5 eV and from multiple samples was utilized to determine the frequency dependent complex-valued isotropic dielectric function for WO₃. We employ a critical-point model dielectric function analysis and determine a parameterized set of oscillators and compare the observed critical-point contributions with the vertical transition energy distribution found within the band structure of WO₃ calculated by density functional theory. We investigate surface roughness with atomic force microscopy and compare to ellipsometric determined effective roughness layer thickness.

Reactive Lamination Of Perovskite Solar Cells., Lyndie Burns

Electronic Theses and Dissertations

Due to the growing demand for energy internationally and the environmental impact of other conventional energy technologies, solar power has been a growing area in the energy landscape. Perovskite research has increased substantially because of the high power conversion efficiencies, up to 22%, with many recent advances in the use of these organic-inorganic hybrid perovskites for photovoltaic cells. However, to bring perovskite solar cells into the industrial world, the overall cost of the manufacturing of the solar cell must be improved to compete with other well-developed photovoltaic technologies. Here is presented an alternative perovskite deposition method for methylammonium lead halide …

Investigation Of Nanomaterial Based Photovoltaic Panel Packaging Materials, Xingeng Yang

Graduate Theses and Dissertations

In this research, nanomaterial-based packaging materials for photovoltaic (PV) panels are investigated. A hydrophobic/anti-reflective surface coating which not only repels water from the top glass of a PV panel but at the same time reduces its light reflectance is investigated. COMSOL simulation results indicate that taller ellipsoid rod (aspect ratio = 5) reflects less light than shorter rod (aspect ratio = 0.5) in the desired spectrum for solar energy harvest from 400nm-700nm. The addition of a polymer layer on these ellipsoid rods broadens the light incident angle from 23° to 34°, from which light can be efficiently absorbed. Based on …

Near Bandgap Two-Photon Excited Luminescence Of Inas Quantum Dots, Xian Hu

Graduate Theses and Dissertations

Semiconductor quantum dots (QDs) confine carriers in three dimensions, resulting in atomic-like energy levels as well as size-dependent electrical and optical properties. Self-assembled III-V QD is one of the most studied semiconductor QDs thanks to their well-established fabrication techniques and versatile optical properties. This dissertation presents the photoluminescence (PL) study of the InAs/GaAs QDs with both above bandgap continuous-wave excitation (one-photon excitation) and below-bandgap pulse excitation (two-photon excitation). Samples of ensemble QDs, single QD (SQD), and QDs in a micro-cavity, all grown by molecular beam epitaxy, are used in this study. Morphology of these samples was examined using atomic force …

Structure And Property Of Polymers And Biopolymers From Molecular Dynamic Simulations, Xiaoquan Sun

Graduate Theses and Dissertations

Natural and synthetic polymers and biopolymers have been studied for a variety of applications in food emulsion, biopharmaceutical purification, tissue engineering, and biosensor. The structure and property of polymers and biopolymers are critically important to determine their functions. Molecular dynamics (MD) simulations have a unique advantage to explore the structure and property of polymers and biopolymers from the molecular level. In the dissertation, MD simulations were conducted to study the mechanisms of various biological and chemical processes controlled by polymers and biopolymers based on real-world experimental results.

Seven heptapeptides have been screened from a peptide library in our earlier study …

Phase Transitions In Monochalcogenide Monolayers, Mehrshad Mehboudi

Graduate Theses and Dissertations

Since discovery of graphene in 2004 as a truly one-atom-thick material with extraordinary mechanical and electronic properties, researchers successfully predicted and synthesized many other two-dimensional materials such as transition metal dichalcogenides (TMDCs) and monochalcogenide monolayers (MMs). Graphene has a non-degenerate structural ground state that is key to its stability at room temperature. However, group IV monochalcogenides such as monolayers of SnSe, and GeSe have a fourfold degenerate ground state. This degeneracy in ground state can lead to structural instability, disorder, and phase transition in finite temperature. The energy that is required to overcome from one degenerate ground state to another …

The Incorporation Of Graphene To Lithium Cobalt Oxide As A Cathode To Improve The Performance Of Lithium Ion Batteries, Kenan Wang

Graduate Theses and Dissertations

One of the objectives of this thesis work was to investigate the cathode performance of lithium cobalt oxide (LiCoO2) incorporated with graphene powder in lithium ion batteries (LIBs). Graphene powder was incorporated into cathode materials to enhance the performance of LIBs. The other objective was to impede the construction of a solid electrolyte interphase (SEI) sheet using graphene sheet coating on its cathode.

The results of this work show that adding graphene powder improved the performance of LiCoO¬2 as a cathode material. With the incorporation of different weight percentages of graphene powder, the LiBs showed distinct changes in their charging …

Self-Assembled Barium Titanate Nanoscale Films By Molecular Beam Epitaxy, Timothy Allen Morgan

Graduate Theses and Dissertations

One challenge of investigating ferroelectrics at the nanoscale has been controlling the stoichiometry during growth. Historically, the growth of barium titanate (BaTiO3) by molecular beam epitaxy has relied on a growth technique called shuttered RHEED. Shuttered RHEED controls the stoichiometry of barium titanate through the precise deposition of alternating layers of BaO and TiO2. While this approach has achieved 1% control of stoichiometry, finding self-limiting mechanisms to lock-in stoichiometry has been the focus of the growth community. The Goldschmidt tolerance factor predicts an unstable perovskite when barium sits in the titanium lattice site. The BaO-TiO2 phase diagram predicts a low-solubility …

Molybdenum Sulfide Prepared By Atomic Layer Deposition: Synthesis And Characterization, Steven Payonk Letourneau

Boise State University Theses and Dissertations

Molybdenum disulfide (MoS₂) is the prototypical two-dimensional (2D) semiconductor. Like graphite, it has a layered structure containing weak van der Waals bonding between layers, while exhibiting strong covalent bonding within layers. The weak secondary bonding allows for isolation of these 2D materials to single layers, like graphene. While bulk MoS₂ is an indirect band gap semiconductor with a band gap of ~1.3 eV, monolayer MoS₂ exhibits a direct band gap of ~1.8 eV, which is an attractive property for many opto-electronic applications. Atomic layer deposition (ALD) has been used to grow amorphous films of MoS_{2 …}

Redshirt In Engineering: A Model For Improving Equity And Inclusion, Donna C. Llewellyn, Ann Delaney, Janet Callahan

Materials Science and Engineering Faculty Publications and Presentations

The NSF-funded Redshirt in Engineering Consortium was formed in 2016 with the goal of enhancing the ability of academically talented but underprepared students coming from low-income backgrounds to successfully graduate with engineering degrees. The Consortium takes its name from the practice of redshirting in college athletics, with the idea of providing an extra year and support to help promising engineering students complete a bachelor’s degree. The Consortium builds on the success of three existing “academic redshirt” programs and expands the model to three new schools. The Existing Redshirt Institutions (ERIs) help mentor and train the new Student Success Partners (SSP), …

Preparations And Corrosion Protection Investigations Of Diethylene Triamine Penta(Methylene Phosphonic Acid)-Zn2+ Conversion Coatings On Cold Rolled Steel Substrates, Wei He, Ru Yan, Ying-Qi Wang, Xiang Gao, Hou-Yi Ma

Journal of Electrochemistry

Novel diethylene triamine penta(methylene phosphonic acid) (DTPMPA)-zinc ion (Zn²⁺) conversion coatings with uniform blue color and excellent corrosion protection were directly formed on the cold rolled steel (CRS) substrates by immersing a CRS plate into the film-forming solutions containing the appropriate concentrations of DTPMPA and Zn²⁺ ion at the proper pH. In this paper, surface morphologies and elemental compositions of DTPMPA-Zn²⁺ conversion coatings were characterized by SEM and EDS, respectivey. The surface functional groups, chemical constituents and binding modes to the substrates were investigated by means of FTIR and XPS methods. The influences of DTPMPA concentrations …

Effects Of Rotating Magnetic Fields On Pem Fuel Cell Performance, Mao-Liang Wu, En-Ze Wang, Guang-De Pan, Zhong-Jun Liu, Fei Xie

Journal of Electrochemistry

Proton Exchange Membrane (PEM) fuel cell performance may be improved by application of additional magnetic fields. In this work, one square permanent magnet, made of either 16 combination cylinder magnets with homopolarity or 16 combination cylinder magnets with heteropolarity, was exerted on the fuel cell surface to produce additional magnetic field affecting PEM fuel cell performance. The influences of magnetic field status (rotating, static and none) on polarization and power density curves measured in a PEM fuel cell were investigated. The results verified the benefit of magnetic field, proving that the magnetic field distribution could improve the fuel cell output. …