Materials Science and Engineering Commons^™

Optimization And Characterization Of Novel Injection Molding Process For Metal Matrix Syntactic Foams, Myranda Spratt, Joseph William Newkirk

Materials Science and Engineering Faculty Research & Creative Works

Metal matrix syntactic foams are particulate composites comprised of hollow or porous particles embedded in a metal matrix. These composites are difficult to manufacture due primarily to the lightweight, relatively fragile filler material. In this work, an injection molding process was developed for metal matrix syntactic foams. First, an aqueous binder was optimized for low-pressure injection molding. A mixture model was used to optimize the composition of the binder to achieve the highest relative density. The model predicted the maximum relative density was at a binder composition (in vol.%) of 7% agar, 4% glycerin, and 89% water. Second, this binder …

Numerical Analysis Of A Roadway Piezoelectric Harvesting System, Abdul Rahman Badawi

Mechanical & Aerospace Engineering Theses & Dissertations

Highways, streets, bridges, and sidewalks with heavy traffic dissipate a considerable amount of waste mechanical energy every day. Piezoelectric energy harvesting devices are a very promising technology that can convert the waste mechanical energy to clean and renewable energy to enhance the sustainability of infrastructures. Research efforts in large-scale energy harvesting have led to the advancement of piezoelectric devices to the point that large-scale implementation is starting to become more feasible. The energy harvested by these devices can be used in many ways such as providing heating or cooling, melting ice, monitoring structural conditions in bridges and tunnels, and powering …

Growth And Characterization Of Semiconductor Materials And Devices For Extreme Environments Applications, Abbas Sabbar

Graduate Theses and Dissertations

Numerous industries require electronics to operate reliably in harsh environments, such as extreme high temperatures (HTs), low temperature (LT), radiation rich environments, multi-extreme, etc. This dissertation is focused on two harsh environments: HT and multi-extreme.

The first study is on HT optoelectronics for future high-density power module applications. In the power modules design, galvanic isolation is required to pass through the gate control signal, reject the transient noise, and break the ground loops. The optocoupler, which consists of a lighting emitting diode (LED) and photodetector (PD), is commonly used as the solution of galvanic isolation at room temperatures. There is …

Static And Dynamical Properties Of Multiferroics, Sayed Omid Sayedaghaee

Graduate Theses and Dissertations

Since the silicon industrial revolution in the 1950s, a lot of effort was dedicated to the research and development activities focused on material and solid-state sciences. As a result, several cutting-edge technologies are emerging including the applications of functional materials in the design and enhancement of novel devices such as sensors, highly capable data storage media, actuators, transducers, and several other types of electronic tools. In the last two decades, a class of functional materials known as multiferroics has captured significant attention because of providing a huge potential for new designs due to possessing multiple ferroic order parameters at the …

Fourier Transform Infrared Spectroscopy For The Measurement Of Gesn/(Si)Gesn, Solomon Opeyemi Ojo

Graduate Theses and Dissertations

Photoluminescence (PL) and Electroluminescence (EL) characterization techniques are important tools for studying the optical and electrical properties of (Si)GeSn. Light emission from these PL and EL measurements provides relevant information on material quality, bandgap energy, current density, and device efficiency. Prior to this work, the in-house PL set-up of this lab which involves the use of a commercially-obtained dispersive spectrometer was used for characterizing both GeSn thin film and fabricated devices, but these measurements were limited by issues bordering on low spectral resolution, spectral artifacts, and poor signal-to-noise ratio (SNR) thereby resulting in the possible loss of vital information and …

Kinetic Monte Carlo Investigations Involving Atomic Layer Deposition Of Metal-Oxide Thinfilms, David Tyler Magness

Graduate Theses/Dissertations

Atomic Layer Deposition is a method of manufacturing thin film materials. Metal-oxides such as zinc-oxide and aluminum-oxide are particularly interesting candidates for use in microelectronic devices such as tunnel junction barriers, transistors, Schottky diodes, and more. By adopting a 3D Kinetic Monte Carlo model capable of simulating ZnO deposition, the effect of parameters including deposition temperature, chamber pressure, and composition of the initial substrate at the beginning of deposition can be investigated. This code generates two random numbers: One is used to select a chemical reaction to occur from a list of all possible reactions and the second is used …

Design, Discovery, And Characterization Of Single Crystals Of A Topological Semimetal Using A Self-Flux Method, Sudha Krishnan

Graduate Theses/Dissertations

Realization of topological semimetals in the recent past show that ternary intermetallics can exhibit topological phases. This discovery initiated the quest for this novel research. There is a crucial need to discover new materials that manifest these phases for a better understanding of their behavior to utilize them in device technology. Also, Bi compounds have attracted much attention as candidates for topological materials and topological superconductors. In this context, synthesis and characterization of single crystals of a layered transition metal pnictide SmMnBi2, a potential Dirac topological semimetal candidate, is reported. A flux method was utilized to synthesize single crystals of …

Parametric Analysis Of Particle Spreading With Discrete Element Method, Yuxuan Wu

Doctoral Dissertations and Master's Theses

The spreading of metallic powder on the printing platform is vital in most additive manufacturing methods, including direct laser sintering. Several processing parameters such as particle size, inter-particle friction, blade speed, and blade gap size affect the spreading process and, therefore, the final product quality. The objective of this study is to parametrically analyze the particle flow behavior and the effect of the aforementioned parameters on the spreading process using the discrete element method (DEM). To effectively address the vast parameter space within computational constraints, novel parameter sweep algorithms based on low discrepancy sequence (LDS) are utilized in conjunction with …

Raman Spectroscopic Investigation Of The Speciation Of Uranyl (Vi) And Thorium (Iv) Ions In Chloride-Bearing Aqueous Solutions Under Hydrothermal Conditions, Nadib Akram

Graduate Theses/Dissertations

Raman spectra were acquired for a uranyl chloride aqueous solution at temperatures ranging from 25°C to 500°C at the chloride concentration of 6M and uranium (vi) concentration of 0.05M. The measurements were taken by sealing the sample in a hydrothermal diamond anvil cell (HDAC) which enabled spectra acquisition at non-ambient conditions. The pressure inside the cell was measured by estimating the liquid-vapor homogenization temperature (T_H) and using the isochoric equation of state diagram of water. The acquired spectra were then fitted to determine the speciation distribution of the various uranyl chloride species for the mentioned concentration. The developed …

Synthesis Of Novel Coo/Mnfe2o4 Heterostructured Nanoparticles And The Effects Of Variable Size And Extent Of Overgrowth On Their Magnetic Properties, Mohammad Tauhidul Islam

Graduate Theses/Dissertations

A combination of thermal decomposition and surfactant-assisted synthesis route was utilized to synthesize novel CoO/MnFe₂O₄ heterostructured nanoparticles. Four samples of varying CoO core size were synthesized with variable extent of overgrowth phase. XRD, XPS, SEM and TEM data show evidence of MnFe₂O₄ spinel phase overgrowth on CoO rock-salt structured nanoparticles. XPS and magnetic data reveal partial oxidation and formation of Co₃O₄ phase on 7 nm and 19 nm size CoO-based nanoparticles. The remaining samples having 22 nm and 34 nm dimensions show a higher percentage of FiM materials overgrowth on the …

The Effect Of Guide Vane Opening Variations And Total Blades On Cross Flow Turbine Performance Using Computational Fluid Dynamic, Muhamad Akbar Navis, Heru Suryanto, Putut Murdanto

Journal of Mechanical Engineering Science and Technology (JMEST)

Indonesia is an agrarian country that continuously produces water, so it has the potential to develop a hydroelectric power plant. Computational Fluid Dynamic (CFD) application could be used to be an economical, quick, and efficient approach to improve the engineering design and turbine performance. This research aimed to find the effect of guide vane opening variations and total blades on cross-flow turbine performance using CFD simulation. This research used experimental modelling method with ANSYS program for turbine design with 22, 24, and 26 turbine blades and guide vane opening variations of 12°, 16°, 20°, 24°, and 36°. The data were …

Energy And Exergy Efficiency Of Double Slope Passive Solar Still, Jandri Fan Ht Saragi, Wawan Septiawan Damanik

Journal of Mechanical Engineering Science and Technology (JMEST)

Solar desalination functions to filter water, both sea water and brackish water, to produce clean water that is fit for consumption with energy from the sun. Solar energy is a renewable energy source that has been widely studied for its use. One of its uses is in a double slope passive solar still where the sun is the main source. Energy and exergy obtained from solar energy are not all used to evaporate water in the desalination system, so it is necessary to calculate efficiency energy and exergy in the system. This study aims to obtain data on the amount …

Characteristics Biolubricant Enriched With Nanoparticle Additives: A Review, Zhahra Hanif Sholiha, Gaguk Jatisukamto

Journal of Mechanical Engineering Science and Technology (JMEST)

The engine movement mechanism is a system composed of machine elements that contact or rub against each other between these surfaces. Surfaces that rub against each other will cause a friction force that causes wear on the surface, so it requires energy to fight the friction force. Lubricants are needed to reduce friction and reduce wear rates, where lubricants are generally made of mineral materials. Lubricants made from synthetic materials are non-renewable and cause environmental problems. The development of biolubricants as lubricating materials based on animal fats or vegetable oils is continuously being carried out. This study aims to observe …

Optimization Of Stir Casting Of Aluminum Matrix Composites (Amcs) With Filler Of Recycled Glass Powder (Rgp) For The Mechanical Properties, Yusup Hendronursito, Tumpal Ojahan, Anang Anshori, Asep Yunanto

Journal of Mechanical Engineering Science and Technology (JMEST)

A study of making Aluminum Matrix Composites (AMCs) uses recycled glass powder (RGP) as a filler has been carried out through the stir casting process. The experimental design uses the Taguchi method of 3^3 orthogonal array L9 with the parameters of powder size (20>x> 80, 80>y> 200, 200>z> 325), percentage of filler vs matrix (2%, 7%, 12%), and stirring time (30 Seconds, 3 Minutes, 12 Minutes). The optimum conditions for the hardness of Al-GRp composites were obtained from specimens with Mesh powder size parameters 200> z> 325, the percentage of glass vs aluminum powder was 12% wt, …

Surface Properties And Adsorption Capacities Of Rice Bran-Activated Carbon, Dewa Ngakan Ketut Putra Negara, Tjokorda Gde Tirta Nindhia, Wayan Nata Septiadi

Journal of Mechanical Engineering Science and Technology (JMEST)

The growing need for activated carbon requires alternative raw materials to replace non-renewable raw materials whose existence is decreasing. Biomass is a very promising precursor, one of which is from rice bran. This research concerns the development of activated carbon derived from rice bran. Carbonization was carried out at 600 OC and physically activated with nitrogen flow rates of 150 mL/min for 40, 80, and 120 minutes. The activated carbons produced (AC-D40, AC-D80, and AC-D120) were characterized to determine the surface properties, surface morphology, and adsorption capacity for nitrogen and blue methylene adsorptions. The results showed that activated carbon that …

Design Of Savonius Vertical Axis Wind Turbine For Vehicle, Filian Arbiyani, Fernando Pranata Lasut

Journal of Mechanical Engineering Science and Technology (JMEST)

The use of cellular phones is increasing in society, but due to the limited battery capacity of cell phones, it is necessary to charge the battery when travelling in the long distances. The Savonius type wind turbine has a potential as an energy source harvesting the wind energy flowing around the car. However, due to the available space on the car, careful design of Savonius vertical axis wind turbine for vehicle is necessary. The research is conducted numerically using MATLAB software. The wind speed, Reynolds number, and electric power output are numerically simulated to obtain the swept area design. Innovative …

New Design Of Aluminum 6061 Welding Joining Using Friction Stir Welding Method, Widia Setiawan, Nugroho Santoso, Surojo Surojo

Journal of Mechanical Engineering Science and Technology (JMEST)

Parallel, lap, corner, and T joints are commonly used in fusion welding and solid welding. Other joints made are lap and butt joint. This study aims to evaluate a new design of fitting model single U and double U for friction stirr welding of Aluminum. Aluminum sheet 6061with a thickness of 10 mm, will be cut to a length of 150 mm and a width of 100 mm, then a locking groove will be made with an inner size of 5 mm and a length of 150 mm The flow is used to be paired in the FSW process. This …

Tool Life Prediction Of Ti [C,N] Mixed Alumina Ceramic Cutting Tool Using Gradient Descent Algorithm On Machining Martensitic Stainless Steel, Joseph Daniel S, Senthil Kumar A

Journal of Mechanical Engineering Science and Technology (JMEST)

In automated manufacturing systems, most of the manufacturing processes, including machining, are automated. Automatic tool change is one of the important parameters for reducing manufacturing lead time. Machining studies on Martensitic Stainless Steel was conducted using Ti[C,N] mixed alumina ceramic cutting tool. Tool life was evaluated using flank wear criterion. The tool life obtained from experimental machining process was taken as training dataset and test dataset for machine learning. Tool life model was developed using Gradient Descent Algorithm. The accuracy of the machine learning model was tested using the test data, and 99.83% accuracy was obtained.

Moisture Reduction Of Honey In Dehumidification And Evaporation Processes, Anang Lastriyanto, Sasongko Aji Wibowo, Erwan Erwan, Firman Jaya, Jati Batoro, Dewi Masyithoh, J.S.A Lamerkabel

Journal of Mechanical Engineering Science and Technology (JMEST)

The high water content of honey can lead to fermentation and accelerate the deterioration of honey. One way to prevent fermentation in honey is to reduce the water content of honey. There are several ways to reduce the water content of honey, namely through a dehumidifier and evaporation. This study aimed to examine the relationship of reduced water content towards time in between dehumidifier and evaporation processes. The research method uses an exponential equation model to determine the value of the constant (K). The constant value (K) is used to predict the rate of reduction in moisture content between the …

The Economics Of Classroom 3-D Printing Of Open-Source Digital Designs Of Learning Aids, Nicole Gallup, Joshua M. Pearce

Michigan Tech Publications, Part 1

While schools struggle financially, capital for purchasing physical learning aids is often cut. To determine if costs could be reduced for learning aids, this study analyzed classroom-based distributed digital manufacturing using 3-D printing of open-source learning aid designs. Learning aid designs are analyzed in detail for their economic viability considering printing and assembly costs with purchased components and compared to equivalent or inferior commercial products available on Amazon. The results show current open-source 3-D printers are capable of manufacturing useful learning aids and that doing so provides high economic savings in the classroom. Overall, the average learning aid would save …