Materials Science and Engineering Commons^™

The Effect Of Cement And Blast Furnace Slag Characteristics On Expansion Of Heat-Cured Mortar Specimens, Jair G. Burgos

USF Tampa Graduate Theses and Dissertations

Delayed ettringite formation (DEF) is a durability issue that typically occurs in concrete exposed to high temperatures at an early age such as precast elements and massive concrete structural elements. There are many advantages to precast concrete such as its quality control, better safety control, and reusable forms, which make them cheaper than casting on site [1]. Heat curing of precast concrete is conducted to obtain high early-strength. However, in doing so, durability issues can arise in the form of internal sulfate attack also known as DEF, if the internal temperature of concrete exceeds 70°C. Past this threshold, ettringite decomposes …

Temperature-Immune Self-Referencing Fabry–Pérot Cavity Sensors, Hengky Chandrahalim, Jonathan W. Smith

AFIT Patents

A passive microscopic Fabry-Pérot Interferometer (FPI) sensor an optical fiber a three-dimensional microscopic optical structure formed on a cleaved tip of an optical fighter that reflects a light signal back through the optical fiber. The reflected light is altered by refractive index changes in the three-dimensional structure that is subject to at least one of: (i) thermal radiation; and (ii) volatile organic compounds.

High Quality Single-Crystalline Aluminum Nitride Grown Using Pulsed Atomic-Layer Epitaxy Technique By Mocvd On Sapphire Substrate, Mohd Nazri Abd Rahman

Student Works (2020-2029)

The unique structural properties and engineering characteristics of nitride-based materials have given them a special position in semiconductor applications. Alloys with a tuned energy bandgap from ultraviolet to infrared wavelengths are possible to be deposited in maintaining the wurtzite crystal structure. However, the aluminum nitride / aluminum gallium nitride (AlN/AlGaN) based hetero-structures for deep-ultraviolet (DUV) emitters as well as AlN-based actuators and piezoelectric sensors are highly inefficient owing to the excessive mismatch in thermal and lattice features between these epilayers with flat c-plane sapphire substrates, resulting in crack formation and high dislocation densities. This thesis mainly focuses on the development …

Study Of Laser Based Additive Manufacturing For Titanium And Copper Alloys, Congyuan Zeng

LSU Doctoral Dissertations

Material processing by laser is increasingly applied in industrial applications for its outstanding characteristics, such as localized heating, high efficiency, and high manufacturing precision. In this study, two kinds of laser material processing strategies were investigated, namely laser surface engineering and laser-powder-bed fusion additive manufacturing, with pure titanium and copper alloys as target materials, respectively.

For laser surface engineering related studies, the work includes the investigation of the dynamic interactions between titanium and pure nitrogen or ambient air under transient laser processing conditions. Thanks to the in-situ synchrotron X-ray diffraction tests, the high-temperature reaction steps between titanium and pure nitrogen/ambient …

Investigation On The Performance Of Tetraglyme Based Solid Copolymer Electrolytes For Solid State Electrical Double Layer Capacitors (Edlcs), Sinasamy Sharmilah

Student Works (2020-2029)

Solid polymer electrolytes (SPEs) have been the focus of intensive research due to their large demand in applications such as electrochemical capacitors, fuel cells, solar cells and batteries. They have shown many advantages such as wider electrochemical potential window, good thermal stability, low volatility and easy handling. Due to these advantages, SPEs have great potential in energy storage applications. Usually, SPEs suffer from poor conductivity, which hinders its performance for energy storage applications. In order to enhance the conductivity of the SPEs, the host polymer incorporated with salt to provide ions for conductivity, ionic liquid to enhance the conductivity and …

A Macro-Scale Ruck And Tuck Mechanism For Deformation In Ion-Irradiated Polycrystalline Graphite, Steve Johns, Karthik Chinnathambi

Materials Science and Engineering Faculty Publications and Presentations

A vein structure, which becomes more pronounced with increasing ion dose, was found on the surface of polycrystalline HOPG (highly oriented pyrolytic graphite) implanted by ex situ C⁺ (up to 1.8x10¹⁷ ions/cm²), and in situ Ar⁺ in a transmission electron microscope (TEM). These veins are found to be independent of the crystallographic orientations and are associated with the formation of pores. Underneath the veins, a triangular-shaped core was formed with the graphite platelet inside the core displaced up towards the surface. A macro-scale ‘ruck&tuck’ geometry was thus generated at these triangle structure boundaries. Progressive movement …

Open-Source Molecular Modeling Software In Chemical Engineering Focusing On The Molecular Simulation Design Framework, Eric Jankowski

Materials Science and Engineering Faculty Publications and Presentations

Molecular simulation has emerged as an important sub-field of chemical engineering, due in no small part to the leadership of Keith Gubbins. A characteristic of the chemical engineering molecular simulation community is the commitment to freely share simulation codes and other key software components required to perform a molecular simulation under open-source licenses and distribution on public repositories such as GitHub. Here we provide an overview of opensource molecular modeling software in Chemical Engineering, with focus on the Molecular Simulation Design Framework (MoSDeF). MoSDeF is an open-source Python software stack that enables facile use of multiple open-source molecular simulation engines, …

Blood Driven Biopower Cells: Acquiring Energy From Reverse Electrodialysis Using Sodium Concentrations From The Flow Of Human Blood, Efecan Pakkaner, Chase Smith, Christina Trexler, Jamie Hestekin, Christa Hestekin

Chemical Engineering Faculty Publications and Presentations

With the growth of the healthcare industry, small scale power sources are needed to support advancements in medical implants, artificial organs, and sensors throughout the body. However, it remains a challenge to find safe, reliable, and stable power sources for these devices. In this study, a miniaturized reverse electrodialysis (RED) biopower cell design using physiological salinity concentration differences between renal bloodstreams is explored for its potential to be used as a power supply for implantable medical devices. Two small scale RED devices produced consistent power for up to three to ten days, depending on the device design. A two-fold decrease …

First-Principles Studies Of Mof Absorption On Hydroxylated And Non-Hydroxylated Metal Oxide Surfaces And Implications For Atomic Layer Deposition Of Mos2, Matthew Lawson, Elton Graugnard, Lan Li

Materials Science and Engineering Faculty Publications and Presentations

Significant interest in two-dimensional transition metal dichalcogenides has led to numerous experimental studies of their synthesis using scalable vapor phase methods, such as chemical vapor deposition (CVD) and atomic layer deposition (ALD). ALD typically allows lower deposition temperatures, and nucleation of chemical precursors requires reactions with surface functional groups. A common first-principles method used to study ALD modeling is the calculation of activation energy for a proposed reaction pathway. In this work we calculated the partial charge densities, local density of states (LDoS), Bader charge analysis, adsorption energies, and charge density difference using density functional theory (DFT) to investigate the …

Interface Structure And Luminescence Properties Of Epitaxial Pbse Films On Inas(111)A, Kevin D. Vallejo, Paul J. Simmonds

Materials Science and Engineering Faculty Publications and Presentations

Epitaxial heterostructures of narrow-gap IV-VI and III-V semiconductors offer a platform for new electronics and mid-infrared photonics. Stark dissimilarities in the bonding and the crystal structure between the rocksalt IV–VIs and the zincblende III–Vs, however, mandate the development of nucleation and growth protocols to reliably prepare high-quality heterostructures. In this work, we demonstrate a route to single crystal (111)-oriented PbSe epitaxial films on nearly lattice-matched InAs (111)A templates. Without this technique, the high-energy heterovalent interface readily produces two populations of PbSe grains that are rotated 180° in-plane with respect to each other, separated by rotational twin boundaries. We find that …

On Road Coordinates For Autonomous Vehicle Guidance, Ricardo Jacome

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

A new roadmap framework is proposed to improve the guidance and trajectory prediction capabilities of connected and automated vehicles (CAVs). Independent of road shape determination through external sensors, the system serves as a backup for challenging conditions, such as low sensor visibility and adverse environmental effects (e.g., rain, fog, snow). Based on the fusion of vehicle dynamics principles, differential geometry, and road design standards, the roadmap framework provides a consolidated collection of critical reference points of roadway centerlines and information about the shape of the roadway in the vicinity of a vehicle, including curvature, optimal travel velocity, and road alignment …

Fatigue Of Two Oxide/Oxide Ceramic Matrix Composites At 1200°C In Air And In Steam. Effect Of Diamond Drilled Effusion Holes, Anthony R. Cabri

Theses and Dissertations

The tension-tension fatigue behavior of two oxide-oxide ceramic matrix composites (CMCs) was investigated at 1200°C in laboratory air and steam. Both composites consist of a porous oxide matrix reinforced with laminated, woven mullite/alumina (NextelTM720) fibers. The first composite had an alumina matrix, while the second had an alumina-mullite matrix. First, we assessed the effects of incorporating mullite into the matrix material on fatigue performance by studying the tension-tension fatigue behavior of alumina-mullite matrix CMC. Second, we evaluated the effects of effusion holes on the alumina matrix CMC's fatigue performance. Specimens containing an array of 17 effusion holes of 0.5-mm diameter …

Static Fatigue Of Hi-Nicalon™ S Ceramic Fiber Tows At 600°C In Air And Silicic Acid-Saturated Steam, Caleigh M. Nelson

Theses and Dissertations

Ceramic matrix composites (CMCs) have the potential to be utilized in applications such as hypersonic vehicles, aircraft leading edges, hot sections of engines, and rocket nozzles. Of particular interest are advanced SiC/SiC composites that can withstand the elevated temperatures and harsh oxidizing environments while maintaining their properties and structural integrity under an applied load. Steam, a major component of combustion environment, is one such aggressive oxidizing environment. As steam passes through the SiC/SiC composite, entering the composite interior through the cracks in the SiC matrix, it becomes saturated with silicic acid, Si(OH)₄. Before incorporating SiC/SiC composites in the …

Fiber Optic Sensor Embedded Smart Helmet For Real-Time Impact Sensing And Analysis Through Machine Learning, Yiyang Zhuang, Qingbo Yang, Taihao Han, Ryan O'Malley, Aditya Kumar, Rex E. Gerald Ii, Jie Huang

Electrical and Computer Engineering Faculty Research & Creative Works

Background: Mild traumatic brain injury (mTBI) strongly associates with chronic neurodegenerative impairments such as post-traumatic stress disorder (PTSD) and mild cognitive impairment. Early detection of concussive events would significantly enhance the understanding of head injuries and provide better guidance for urgent diagnoses and the best clinical practices for achieving full recovery. New method: A smart helmet was developed with a single embedded fiber Bragg grating (FBG) sensor for real-time sensing of blunt-force impact events to helmets. The transient signals provide both magnitude and directional information about the impact event, and the data can be used for training machine learning (ML) …

The Corrosion Of Stainless Steel Made By Additive Manufacturing: A Review, Gyeongbin Ko, Wooseok Kim, Kyungjung Kwon, Tae-Kyu Lee

Mechanical and Materials Engineering Faculty Publications and Presentations

The advantages of additive manufacturing (AM) of metals over traditional manufacturing methods have triggered many relevant studies comparing the mechanical properties, corrosion behavior, and microstructure of metals produced by AM or traditional manufacturing methods. This review focuses exclusively on the corrosion property of AM-fabricated stainless steel by comprehensively analyzing the relevant literature. The principles of various AM processes, which have been adopted in the corrosion study of stainless steel, and the corrosion behaviors of stainless steel depending on the AM process, the stainless steel type, and the corrosion environment are summarized. In this comprehensive analysis of relevant literature, we extract …

Static Fatigue Of Hi-Nicalon S Fiber Tows At 500°C In Air And In Silicic Acid-Saturated Steam, Richard J. Reinink

Theses and Dissertations

Recent developments in aerospace propulsion systems, along with emerging interest in hypersonic air vehicles has emphasized the need for materials which can withstand extreme service environments. The leading candidates for the structural components expected to operate in these environments are SiC-based ceramic matrix composites (CMCs). When a CMC component is subjected to thermomechanical loads in an aggressive environment during service, surface cracks form. As steam penetrates cracks in the SiC matrix, it becomes saturated with silicic acid, (SI(OH)₄) and attacks the SiC fibers. The interaction between the Hi-Nicalon™ S SiC fibers and the (SI(OH)₄)-saturated steam is …

Comparing The Environmental Impacts Of Using Mass Timber And Structural Steel, Khang Hoang Nguyen, Steelee Knight Morgan

Construction Management

Although mass timber has seen a gradual rise in demand in the past, there has been a lack of extensive research on the environmental impacts of using mass timber as a primary structural framing material. This paper compares structural steel, and mass timber’s total embodied carbon emissions. Accurate estimates were made using plans and specs for different projects retrieved from semi-structured interviews. The estimates were input through the EC3 Calculator to provide extensive total carbon emissions measurements between each construction material. Using structural steel framing increased the project’s overall environmental impact by roughly 84% compared to using mass timber. The …

Preparation Of Pdcoir Tetrahedron Nanocatalysts And Its Performance Toward Ethanol Oxidation Reaction, Zhi-Yuan Yu, Rui Huang, Jie Liu, Guang Li, Qian-Tong Song, Shi-Gang Sun

Journal of Electrochemistry

As a new energy conversion device, direct ethanol fuel cells (DEFCs) are widely concerned because of their remarkable advantages such as high theoretical energy density and wide fuel sources. However, the rapid development of DEFCs has been severely impeded due to the sluggish kinetic process and toxic intermediates especially in their anodic reactions. Palladium (Pd)-based materials are considered to be excellent anode catalysts for DEFCs, especially under alkaline conditions. And further improving their performance is an important direction to promote the development of DEFCs. Surface structure and composition are the key factors affecting the performance of catalysts which can be …

Preparation And Performance Investigation Of Li-Sgo Doped Semi-Ipns Porous Single Ion Conducting Polymer Electrolyte, Yun-Feng Zhang, Jia-Ming Dong, Chang Tan, Shi-Kang Huo, Jia-Ying Wang, Yang He, Ya-Ying Wang

Journal of Electrochemistry

Herein, the lithiated sulfonated graphene oxide (Li-SGO) was successfully prepared via three steps by sulfonation of graphene oxide with 3-merraptnpropylt rimethnxysilane, oxidation of thiol into sulfonate with hydrogen peroxide and lithiation of sulfonate with aqueous lithium hydroxide. The as-prepared Li-SGO was then introduced into the semi-interpenetrating networks of single ion conducting polymer electrolyte (Li-SGO-FPAS) and poly vinylidenefluoride-hexafluoro propylene (PVDF-HFP) binder by in-situ polymerization to fabricate the porous single ion conducting polymer electrolyte membrane (Li-SGO-po-FPAS) generated from the poor compatibility between aromatic Li-SGO-FPAS and aliphatic PVDF-HFP binder. The key properties such as morphology, porosity, solvent uptake, mechanical …

Preparations And Electrochemical Properties Of Bc/Coni2S4@Ppy Flexible Composites For Supercapacitors, Si-Yuan Peng, Shi-Run Yang, Jing-Hong Zhou, Zhi-Jun Sui, Tao Zhang, Yi Shi, Xing-Gui Zhou

Journal of Electrochemistry

Flexible supercapacitor is one of the most promising energy storage devices for portable and wearable electronic products due to its advantages of high power density, fast charging and long cycle life. Therefore, self-supporting flexible electrode materials with high performance have attained more and more attention both in academia and in industry recently. In this work, using bacterial cellulose (BC) as a flexible substrate, the bacterial cellulose/nickel-cobalt sulfide@polypyrrole (BC/CoNi₂S₄@PPy) flexible composites with three-dimensional porous network and good conductivity were prepared by a combined solvothermal-in-situ polymerization-vacuum filtration method. The samples were characterized by X-ray diffraction, …