Materials Science and Engineering Commons^™

Bio-Based Food Packaging Material For Intelligent Food Packaging Applications For Chicken Fillets, Kalpani Y. Perera, Amit K. Jaiswal, Swarma Jaiswal, Shubham Sharma

Articles

Bionanocomposite packaging is made up of bio- based materials that have high performance activity and are ecologically sustainable alternatives to packaging made of synthetic polymers. Intelligent packaging retains track of the state of the food and the environment in which it is stored, and communicates relevant changes to the consumer through visualization or other methods. The aim of this study was to develop a bionanocomposite intelligent packaging material by utilising sodium alginate, gelatin, nanoclay and curcumin. Sodium alginate, gelatin film incorporated with Curcumin (Cur), and Nanoclay (NC) in various concentrations (0% W/V, 0.5% W/V, 1% W/V and 1. 5% W/V) …

Thermal Post-Processing Of 3d Printed Polypropylene Parts For Vacuum Systems, Pierce Mayville, Aliaksei L. Petsiuk, Joshua M. Pearce

Michigan Tech Publications, Part 1

Access to vacuum systems is limited because of economic costs. A rapidly growing approach to reduce the costs of scientific equipment is to combine open-source hardware methods with digital distributed manufacturing with 3D printers. Although high-end 3D printers can manufacture vacuum components, again, the cost of access to tooling is economically prohibitive. Low-cost material extrusion 3D printing with plastic overcomes the cost issue, but two problems arise when attempting to use plastic in or as part of vacuum systems: the outgassing of polymers and their sealing. To overcome these challenges, this study explores the potential of using post-processing heat treatments …

An Experimental Study Of Norton And Thule Cooking Pot Performance, Caelie Marshall Butler

Dissertations and Theses

Ceramic technology was adopted by hunter-gatherers of the Paleo-Inuit Norton tradition in the Western Arctic between 2800 and 2500 years B.P., corresponding with an increase in the use of aquatic resources. Pottery production and use continued until approximately 1,500 BP, and resumed during the Neo-Inuit Birnirk and Thule periods, approximately 1,350 years BP. The technical characteristics of Norton and Thule ceramics suggest they performed differently when used for cooking, with Norton ceramics best suited for cooking using direct or suspended heat, and Thule ceramics best suited for indirect heat. Prior experimental archaeological research has focused on Thule ceramics, with limited …

Solar Pv Panels-Self-Cleaning Coating Material For Egyptian Climatic Conditions, Iman El-Mahallawi, Engy Elshazly, Olugbenga Timo Oladinrin Dr., Muhammad Qasim Rana Dr.

Renewable Mechanical Energy

No abstract provided.

Study Of Asymptotic Velocity In The Bondi–Hoyle Accretion Flows In The Domain Of Kerr And 4-D Einstein–Gauss–Bonnet Gravities, Orhan Donmez, Fatih Dogan, Tuba Sahin

Materials Science and Engineering Faculty Research & Creative Works

Understanding the physical structures of the accreted matter very close to a black hole in quasars and active galactic nucleus (AGN) is an important milestone to constrain the activities occurring in their centers. In this paper, we numerically investigate the effects of the asymptotic velocities on the physical structures of the accretion disk around the Kerr and Einstein–Gauss–Bonnet (EGB) rapidly rotating black holes. The Bondi–Hoyle accretion is considered with a falling gas towards the black hole in an upstream region of the computational domain. Shock cones are naturally formed in the downstream part of the flow around both black holes. …

Elucidating The Interfacial Bonding Behavior Of Over-Molded Hybrid Fiber Reinforced Polymer Composites: Experiment And Multiscale Numerical Simulation, Gideon A. Lyngdoh, Sumanta Das

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

This paper implements molecular dynamics (MD) simulation using reactive force field (ReaxFF) to evaluate the

atomistic origin of the interfacial behavior in the overmolded hybrid unidirectional continuous carbon fiber low-melt PAEK (CFR- LMPAEK)-short carbon fiber reinforced PEEK (SFR-PEEK) polymer composites. From the MD simulation, it was observed that the

interfacial properties improve with increasing maximum processing temperature and injection pressure although such an improving trajectory gets saturated beyond specific limits. The interfacial strength and fracture response of the hybrid polymer system at the interface are also evaluated. The mechanical responses obtained from MD simulation are used as adhesive properties in …

Irradiation-Induced Amorphous-To-Crystalline Phase Transformations In Ceramic Materials, Cyrus Koroni, Tristan Olsen, Janelle P. Wharry, Hui Xiong

Materials Science and Engineering Faculty Publications and Presentations

Amorphous ceramics are a unique class of materials with unusual properties and functionalities. While these materials are known to crystallize when subjected to thermal annealing, they have sometimes been observed to crystallize athermally when exposed to extreme irradiation environments. Because irradiation is almost universally understood to introduce disorder into materials, these observations of irradiation-induced ordering or crystallization are unusual and may partially explain the limited research into this phenomenon. However, the archival literature presents a growing body of evidence of these irradiation-induced amorphous-to-crystalline (a-to-c) phase transformations in ceramics. In this perspective, the summary and review of examples from the literature …

Developing Scaling Laws To Predict Compressive Mechanical Properties And Determine Geometrical Parameters Of Modified Bcc Lattice Structures, Hasanain Abdulhadi, Abdalsalam Fadeel, Tahseen A. Alwattar, Ahsan Mian

Mechanical and Materials Engineering Faculty Publications

The objective of this study is to develop generalized empirical closed-form equations to predict the compressive mechanical properties and determine geometrical parameters. To achieve that, 117 models are built and analyzed using ABAQUS/CAE 2016 to provide two types of reliable data: one for lattice mechanical properties based on finite element method and the other for geometrical parameters using the measurements of ABAQUS diagnostic tool. All the models are created by modifying the basic feature of body-centered cubic lattice structure based on a range of strut angles, a set of relative densities, and two design sets. Also, the influence of lattice …

Global Tellurium Supply Potential From Electrolytic Copper Refining, Nedal T. Nassar, Haeyeon Kim, Max Frenzel, Michael S. Moats, Sarah M. Hayes

Materials Science and Engineering Faculty Research & Creative Works

The transition towards renewable energy requires increasing quantities of nonfuel mineral commodities, including tellurium used in certain photovoltaics. While demand for tellurium may increase markedly, the potential to increase tellurium supply is not well-understood. In this analysis, we estimate the quantity of tellurium contained in anode slimes generated by electrolytic copper refining by country between 1986 and 2018, including uncertainties. For 2018, the results indicate that 1930 (1500-2700, 95% confidence interval) metric tons of tellurium were contained in anode slimes globally. This is nearly quadruple the reported tellurium production for that year. China has the greatest potential to increase tellurium …

High-Entropy Boride–Carbide Ceramics By Sequential Boro/Carbothermal Synthesis, Steven M. Smith, Lun Feng, William Fahrenholtz, Greg Hilmas, Tieshu Huang

Materials Science and Engineering Faculty Research & Creative Works

A dual-phase high-entropy boride (HEB)/carbide (HEC) ceramic with a fine grain size was synthesized by a sequential boro/carbothermal process. In the first step, an Hf–Nb–Ta–Ti–Zr-containing carbide was synthesized by a carbothermal reduction of oxides followed by the reaction of the carbide with B4C and ZrH2 to convert part of the carbide to boride. The resulting composition was ∼29 vol% HEB with an average grain size of ∼1.1 μm. Solid solution formation occurred at the densification temperature of 1900°C resulting in a relative density higher than 99%. The Vickers hardness was 26.5 ± 1.4 GPa. This is the first report of …

Improved Additive Manufacturing Of Silicon Carbide Parts Via Pressureless Electric Field-Assisted Sintering, Adam Bratten, Ruoyu Chen, Joshua Rittenhouse, Ming-Chuan Leu, Haiming Wen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

High solids loading silicon carbide (SiC)-based aqueous slurries containing only.5 wt. % organic additives were utilized to create specimens of various geometries via an extrusion-based additive manufacturing (AM) technique. Pressure less electric field-assisted sintering was performed to densify each specimen without deformation. The combination of these techniques produced parts with >98% relative density despite containing only 5 wt.% oxide sintering additives. After sintering, specimens contained only the α-SiC and yttrium aluminum perovskite phases. This suggests the evolution of a nonequilibrium yttrium aluminate phase, as well as transformation from β-SiC to α-SiC. The fabrication method presented in this work has advantages …

Effect Of Rolling Process On Magnetic Properties Of Fe-3.3 Wt% Si Non-Oriented Electrical Steel, Yizhou Du, Ronald J. O'Malley, Mario F. Buchely, Paul Kelly

Materials Science and Engineering Faculty Research & Creative Works

In this study, the influence of the rolling process on magnetic properties of Fe-3.3 wt% Si non-oriented electrical steel was investigated. The strip samples were cast using a high solidification cooling rate vacuum sampling method to simulate the solidification conditions of the industrial twin roll thin strip casting (TRSC) process. As-cast samples were subjected to various thermo-mechanical processing routes with different levels of hot-rolling (HR) and cold-rolling (CR). The influence of carbon and sulfur (C&S) contents in the steel were also investigated. Core loss (P1.5/50, P1.5/60, P1.0/50, P1.0/60) and magnetic induction (B25, B50) of the final annealed strip samples were …

Mechanical Activation And Cation Site Disorder In Mgal2o4, Cole A. Corlett, Matthias D. Frontzek, Nina Obradovic, Jeremy Lee Watts, William Fahrenholtz

Materials Science and Engineering Faculty Research & Creative Works

The synthesis and crystallographic site occupancy were investigated for MgAl2O4 with and without mechanical activation of the precursor powders. Heating to 1200 °C or higher resulted in the formation of a single spinel phase regardless of whether the powders were mechanically activated or not. Neutron diffraction analysis was used to determine cation site occupancy and revealed that mechanical activation resulted in a lower degree of cation site inversion compared to the nonactivated materials, which indicated that the powders were closer to thermodynamic equilibrium. This is the first study to characterize the effects of mechanical activation on crystallographic site occupancy in …

Ultrafast Stiffening Of Concentrated Thermoresponsive Mineral Suspensions, Sharu Bhagavathi Kandy, Iman Mehdipour, Narayanan Neithalath, Aditya Kumar, Mathieu Bauchy, Edward Garboczi, Samanvaya Srivastava, Torben Gaedt, Gaurav Sant

Materials Science and Engineering Faculty Research & Creative Works

Extrusion-based 3D printing with rapidly hardening polymeric materials is capable of building almost any conceivable structure. However, concrete, one of the most widely used materials for large-scale structural components, is generally based on inorganic binder materials like Portland cement. Unlike polymeric materials, a lack of precise control of the extent and rate of solidification of cement-based suspensions is a major issue that affects the ability to 3D-print geometrically complex structures. Here, we demonstrate a novel method for controllable-rapid solidification of concentrated mineral suspensions that contain a polymer binder system based on epoxy and thiol precursors as well as one or …

Processing And Mechanical Properties Of Hot-Pressed Zirconium Diboride – Zirconium Carbide Ceramics, Eric W. Neuman, William Fahrenholtz, Gregory E. Hilmas

Materials Science and Engineering Faculty Research & Creative Works

ZrB2 was mixed with 0.5 wt% carbon and up to 10 vol% ZrC and densified by hot-pressing at 2000 °C. All compositions were > 99.8% dense following hot-pressing. The dense ceramics contained 1–1.5 vol% less ZrC than the nominal ZrC addition and had between 0.5 and 1 vol% residual carbon. Grain sizes for the ZrB2 phase decreased from 10.1 µm for 2.5 vol% ZrC to 4.2 µm for 10 vol% ZrC, while the ZrC cluster size increased from 1.3 µm to 2.2 µm over the same composition range. Elastic modulus was ~505 GPa and toughness was ~2.6 MPa·m½ for all compositions. …

Developing Positive Thermal Coefficient (Ptc) Heaters For Solar Electric Cooking, Katarina Ivana Brekalo, Andrew Shepherd

Physics

Positive Thermal Coefficients, PTCs, are materials that abruptly change in resistance in response to changes in temperature. The purpose of this experiment is to explore the viability of using the switching type ceramic PTC thermistor as a replacement for current resistive heaters. These types of PTCs have a nonlinear change in resistance with increases in temperature. This device will be used as a temperature-controlling heating element intended to power an Insulated Solar Electric Cooker (ISEC). The ISEC is designed to cook meals throughout the day for impacted communities as an alternative cooking method that doesn’t require biofuel as an energy …

Influence Of Defects On In-Plane Dynamic Properties Of Hexagonal Ligament Chiral Structures, Ning An, Xunwen Su, Dongmei Zhu, Mileta M. Tomovic

Engineering Technology Faculty Publications

Although the six-ligament chiral structure has many unique properties, due to its special structure, the stress concentration is prone to defects. In addition, additive manufacturing is also prone to defects. This paper studies the effect of defects, which is helpful for the better application of the six-ligament chiral structure. Several new six-ligament chiral structures with random and concentrated defects were designed to explore the effects of the defects on the in-plane dynamic properties. The structures were studied with the finite element ANSYS/LSDYNA numerical simulation and experimental methods. According to the defect-free six-ligament chiral structures exhibiting different deformation modes at different …

Mechanical Properties And Tension-Tension Fatigue Behavior Of A Novel Additively Manufactured Polymer Matrix Composite At Room And Elevated Temperature, Grayson M. Harber

Theses and Dissertations

The tension-tension fatigue behavior of a novel additively manufactured AM carbon fiber reinforced polymer matrix composite was studied. This novel material system consists of T1100 carbon fibers, and a UV photocured resin developed by Continuous Composites and Sartomer. Tensile properties and tension-tension fatigue were investigated for the 090 fiber orientation as well as for the ±45 fiber orientation. Specimens with 0/90 fiber orientation were tested at ambient laboratory temperature 23 °C and at elevated temperature 150 °C, while the specimens with the ±45 fiber orientation were tested only at ambient laboratory temperature. Tension-tension fatigue testing was carried out with a …

Effect Of Current Density Ramping On The Anodic Reaction And Morphology Of Aerospace Aluminum Alloys, Peter Totaro Jr.

Dissertations

Aluminum anodizing has been experimented with and studied over the last century because of its ability to form uniform, well ordered cellular coatings on aluminum alloys. Anodizing aerospace alloys has been problematic, due to the alloying elements used to add strength and resistance to stress cracking corrosion. These intermetallic compounds, i.e., copper and zinc, promote oxygen evolution and stress as they accumulate in and on the surface of the forming aluminum oxide. These inclusions lead to increased electrical resistance that forms porous and flawed coating, which can lead to industrial and field failures. The amount of voltage placed on the …

Machine Learning Mosa Monitoring System, Aditya G. Manjunath, Sabahudin Vrtagic, Fatih Dogan, Milan Dordevic, Mileta Zarkovic, Jasmin Kevric, Goran Dobric

Materials Science and Engineering Faculty Research & Creative Works

This research paper deals with the problem of Metal-Oxide Surge Arrester (MOSA) condition monitoring and a new methodology in surge arrester monitoring and diagnostics is presented. A machine learning algorithm (back propagation regression) is used to estimate the non-linearity coefficient of the surge arrester, based on operating voltage and leakage current of the arrester. Using a simulated system, this research investigates the possibility of application and efficiency of machine learning. It is shown that the applied learning algorithm results are competitive with the model results parameters calculated as R2 = 0.999 and mean absolute real error computed as 0.005 which …