Materials Science and Engineering Commons^™

Transformation Pathways Of Lanthanide-Free Mn-Al-Ga-X Alloys Where X = Co, Fe, And Ni, Shane L. Palmer

Boise State University Theses and Dissertations

Ubiquitous rare-earth, (i.e. lanthanide) permanent magnets (PMs) composed of Nd-Fe-B are the strongest PMs on the market. However, limited mineral sources, complex elemental separation, and supply chain volatility have shifted the lanthanides to critical material status. Inexpensive, readily available materials are sought to fill an energy product performance gap to reduce dependency on lanthanide PMs. Frequently, lanthanide PMs are used in applications where their energy products are excessively high. Mn-Al based permanent magnets offer a potential substitute for PM applications which do not require the high energy product of a lanthanide PM. MnAl alloys form a metastable ferromagnetic tetragonal …

Integrating Sensor Development, Risk Assessment, And Community Engagement To Support Environmental Justice In The Rural Community Of El Tiple, Colombia, David Bahamon Pinzon

All Dissertations

In Colombia, ethnic communities have traditionally been responsible stewards of natural resources. They recognize the importance of these resources for their livelihood, as well as their ancestral and cultural heritage. El Tiple, a rural Afro-Colombian community, has been affected by the incursion of private corporations that promoted the expansion of sugarcane monocrops in their territory. Since the introduction of the monoculture industry, local freshwater sources have been depleted due to intensive water use for irrigation of the sugarcane crops. Additionally, the intensive usage of agrochemicals has been linked with loss of native flora, damages to family farms, and pollution of …

Chemical And Physical Interaction Mechanisms And Multifunctional Properties Of Plant Based Graphene In Carbon Fiber Epoxy Composites, Daniel W. Mulqueen

Mechanical & Aerospace Engineering Theses & Dissertations

Graphene has generated substantial interest as a filler due to its exceptional strength, flexibility, and conductivity but faces obstacles in supply and implementation. A renewable, plant-based graphene nanoparticle (pGNP) presents a more accessible and sustainable filler with the same properties as mineral graphenes. In this study, the mechanisms of graphene reinforcement in carbon fiber reinforced plastic (CFRP) were examined, along with the resulting improvements to mechanical strength, resistance to crack propagation, electrical and thermal conductivity at elevated temperatures. pGNP, produced from renewable biomass, was shown to have a graphitic structure with flakes 3-10 layers thick and a median lateral size …

Synthesis And Characterization Of Cobalt(Iii) Complexes And A Vanadium(Iv) Complex With Flavonoids As Ligands, Ethan Schroeder

Chemistry & Biochemistry Theses & Dissertations

For many years now, transition metal complexes have been used as favorable additional chemotherapeutic approaches to medicine that were previously unexplored in the literature. One well-known chemotherapeutic drug, cisplatin, has been applied, but is limited in use due to its toxicity to the cells and its undesirable side effects to humans. Newly developed cobalt-based complexes with ligands known as flavonoids are being used to fight cancer. Flavonoids, compounds mainly found in fruits and vegetables, are shown to have antioxidative and anticancer properties. Use of flavonoids as ligands in transition metal complexes, e.g., those with a Ru(II) metal center, have been …

Electrosteric Control Of The Aggregation And Yielding Behavior Of Concentrated Portlandite Suspensions, Sharu Bhagavathi Kandy, Narayanan Neithalath, Mathieu Bauchy, Aditya Kumar, Edward Garboczi, Torben Gaedt, Samanvaya Srivastava, Gaurav Sant

Materials Science and Engineering Faculty Research & Creative Works

Portlandite (calcium hydroxide: CH: Ca (OH)2) suspensions aggregate spontaneously and form percolated fractal aggregate networks when dispersed in water. Consequently, the viscosity and yield stress of portlandite suspensions diverge at low particle loadings, adversely affecting their processability. Even though polycarboxylate ether (PCE)-based comb polyelectrolytes are routinely used to alter the particle dispersion state, water demand, and rheology of similar suspensions (e.g., ordinary portland cement suspensions) that feature a high pH and high ionic strength, their use to control portlandite suspension rheology has not been elucidated. This study combines adsorption isotherms and rheological measurements to elucidate the role of PCE composition …

Development And Characterization Of Lead & Lead-Free Perovskite Solar Cell Materials, Rubaiya Murshed

UNLV Theses, Dissertations, Professional Papers, and Capstones

In recent years, perovskite photovoltaic technology has offered enormous viability and dimensionality in solar cell research. As a light-harvesting active layer, Perovskite generated remarkable development in device efficiency of 25.7% for the single-junction solar cell, and over 33% for the perovskite/silicon tandem solar cell. Also, perovskite-perovskite tandem solar cell (also called all-perovskite tandem solar cell) shows great potential in device performance and achieved a power conversion efficiency (PCE) of 26.4%. Transitioning photovoltaic technology from the laboratory to commercial products, high PCE, low cost, long lifetime, and low toxicity are some of the critical factors to consider during material selection. Pb-halide …

Effect Of Heat Treatment On The Mechanical And Corrosion Properties Of The Cocrnifeal Heas, Ahmed Korra

Masters Theses and Doctoral Dissertations

High entropy alloys (HEAs) are a relatively new class of metallic materials that have shown great potential for use in extreme environments, such as high temperatures and corrosive conditions. Among the different types of HEAs, CoCrNiFeAl HEAs are potential materials for a wide range of applications, including aerospace, biomedical, and energy storage. This work focused on the effects of heat treatment temperatures from 800 °C to 1100 °C on the microstructure and mechanical properties of these alloys, as well as their electrochemical corrosion behavior. A thermodynamic model was implemented to predict the performance of the material. The results of this …

Preparation Of High Entropy Titanite Pyrochlore And Radiation Stability Study, Adam Gootgeld

All Theses

Pyrochlore has been studied as a host phase for safe storage of radionuclides and exists naturally with long-term stability with good long-range order [1]. High entropy oxides show promising tunable properties that could demonstrate favorable bulk deposit of radioactive materials such as spent nuclear fuel (Uranium and other actinides). It is proposed that using high entropy oxides (HEOs) as the cation in this framework will shift the gibbs free energy so that radioactive nuclear waste will be stabilized for safe, long-term, eco-friendly storage. We have established a consistent method to fabricate high entropy titanite pyrochlores. In this study, ion beam …

Double Cantilever Beam Mode-I Testing Validation In Large-Scale Additive Manufacturing Carbon Composite, Luis Alfonso Camacho

Open Access Theses & Dissertations

Testing for mechanical properties for additive manufacturing has been based on already existing standards for traditional manufacturing methods. For composites in large scale additive manufacturing there is a research gap in bond strength and fracture toughness for a single layer interface. By using Double cantilever beam Mode I, this thesis manuscript validates testing parameters and protocols to describe the intricacies of ABS matrix 20 wt.% carbon filled composite, specifically on the layer-to-layer interface. Studies suggest that fracture toughness is sensitive to process parameters, like deflection speed and sharpened crack tip at the layer interface of BAAM 3D printed part and …

Multiscale Modeling And Gaussian Process Regression For Applications In Composite Materials, Joshua Arp

All Dissertations

An ongoing challenge in advanced materials design is the development of accurate multiscale models that consider uncertainty while establishing a link between knowledge or information about constituent materials to overall composite properties. Successful models can accurately predict composite properties, reducing the high financial and labor costs associated with experimental determination and accelerating material innovation. Whereas early pioneers in micromechanics developed simplistic theoretical models to map these relationships, modern advances in computer technology have enabled detailed simulators capable of accurately predicting complex and multiscale phenomena.

This work advances domain knowledge via two means: firstly, through the development of high-fidelity, physics-based finite …

Magnesium-Based Nanocomposites: A Review From Mechanical, Creep And Fatigue Properties, S. Abazari, A. Shamsipur, H. R. Bakhsheshi-Rad, J. W. Drelich, J. Goldman, S. Sharif, A. F. Ismail, M. Razzaghi

Michigan Tech Publications

The addition of nanoscale additions to magnesium (Mg) based alloys can boost mechanical characteristics without noticeably decreasing ductility. Since Mg is the lightest structural material, the Mg-based nanocomposites (NCs) with improved mechanical properties are appealing materials for lightweight structural applications. In contrast to conventional Mg-based composites, the incorporation of nano-sized reinforcing particles noticeably boosts the strength of Mg-based nanocomposites without significantly reducing the formability. The present article reviews Mg-based metal matrix nanocomposites (MMNCs) with metallic and ceramic additions, fabricated via both solid-based (sintering and powder metallurgy) and liquid-based (disintegrated melt deposition) technologies. It also reviews strengthening models and mechanisms that …

Computational And Experimental Study On Undoped And Er-Doped Lithium Tantalate Nanofluorescent Probes, Mkhitar A. Hobosyan, Andrea Pelayo Carvajal, Bhupendra B. Srivastava, Tamanna Zakia, Mohammed Uddin, Karen S. Martirosyan, Eric Rodriguez, Kofi Nketia Ackaah-Gyasi, Nicholas Dimakis

Physics & Astronomy Faculty Publications

We present a combined density functional theory (DFT) and experimental work on lithium tantalate LiTaO3 (LT) and its Er-doped counterparts. We calculate the electronic and optical properties for both LT and LT:Er+3, with Er occupying either Li or Ta sites, at 4.167 mol%. The generalized gradient approximation (GGA) calculations show that the Er-4 f bands appear closer to the conduction band bottom and to the valance band top, for the first and second doped configurations, respectively. This agrees with changes in the imaginary part of the frequency dependent dielectric function between the doped configurations. There are striking differences between the …

Oxidation Of Hafnium Diboride—Silicon Carbide At 1500 °C In Air; Effect Of Compressive Stress, Anthony J. Degregoria, Marina B. Ruggles-Wrenn, Glen E. Pry

Faculty Publications

The long-term oxidation behavior of HfB₂ and of HfB₂-20 vol.% SiC was studied. Test samples of each material were oxidized at 1500 °C in air using a box furnace. The exposure times were 0, 0.5, 1, 2, 3, 6, 9, 12, 15, 30, 45 and 90 h. Weight gain, oxide scale composition and oxide scale thickness were characterized for both materials. Crystal structure of the surface scales was analyzed using x-ray diffraction. Oxide scales were further characterized via scanning electron microscopy with energy dispersive spectroscopy analysis. For HfB₂ the oxide scale consists predominantly of porous HfO …

A Spike-Shaped Anchorage For Steel Reinforced Polymer (Srp)-Strengthened Concrete Structures, Xingxing Zou, Keenan L. Mcburney, Lesley H. Sneed

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Steel reinforced polymer (SRP) composite has recently emerged as an effective and economical solution for strengthening of reinforced concrete (RC) structures. Premature debonding failure of unanchored SRP at low load levels generally governs the performance of RC structures strengthened with externally bonded SRP. Therefore, a novel yet simple spike-shaped anchorage system was proposed in this study to prevent the debonding failure of SRP and to improve the interfacial shear capacity. Experimental investigation through single-lap shear tests of SRP-concrete joints showed that the anchorage system changed the failure mode from composite debonding to fiber rupture. In addition, the anchorage system substantially …

Mechanical Properties Of Biocomposite With Various Composition Of Caco3 And Starch, Agris Setiawan, Fransisca Diana Wahyuningsih, Riria Zendy Mirahati

Journal of Mechanical Engineering Science and Technology (JMEST)

Calcium carbonate has the potential to be used in the development of medical materials, including biomaterials. Biocomposite is composed of CaCO3 as matrix material and bioplastic from the combination of corn starch and cassava starch as reinforcement. This study aims to determine mechanical properties such as tensile strength and bending/flexural strength with varying compositions of CaCO3 and bioplastic. Characterization of the biocomposite uses Scanning Electron Microscope to observe the microstructure and composition elements of their structure. This study used 4 variations in the ratio of CaCO3 suspension: (Corn Starch + Cassava Starch). Each sample was characterized using specimen code A …

Effect Of Grafting Nano-Tio2 On Sansevieria Cylindrica Fiber Properties, Chrisrulita Sekaradi Wiguna, Heru Suryanto, Aminuddin Aminuddin, Jibril Maulana, Joseph Selvi Binoj, Alamry Ali

Journal of Mechanical Engineering Science and Technology (JMEST)

Natural fibers, which are abundant, environmentally friendly, and biodegradable, are used as a replacement for synthetic fibers. The composite strength can be increased by treating the surfaces of natural fibers with suitable chemicals, which can also improve the interface interaction between fiber and matrix. Application of a coupling agent in chemical treatment is utilized to reinforce the bonding between fiber and matrix. The objective of the study is to determine the influence of silane concentration on the Sansevieria cylindrica fiber properties. The methods included fibers treatment using ethanol and coupling agent as dissolving and TiO2 with concentrations of 0%, 0.25%, …

Synthesis And Characterization Of Nitrogen-Doped Activated Carbon For Lithium Battery Anode Applications, Prihanto Trihutomo, Poppy Puspitasari, Muhammad Bustomi Radja, Milzam Rahmat Busono

Journal of Mechanical Engineering Science and Technology (JMEST)

Nitrogen-dopped activated carbon was synthesized to see its effect on the characterization of the nitrogen surface functional groups, crystal size, and morphology of the resulting sample. Synthesis of nitrogen-doped activated carbon was carried out by varying the addition of Urea as a nitrogen doping source. Activated carbon compared its characteristics with variations in the concentration of added Urea to activated carbon, at 1:3 and 1:5. The FTIR results obtained were the presence of functional groups indicating the presence of nitrogen bonds in each sample. The crystallinity results showed that the samples were classified as crystalline and nitrogen doping influenced the …

Designing A Naabsa Class Tanker Ship With Bottom Protection From Ground, Victor A. Kulesh, Mathias B. Prasetio, Fam Chung Hiep

Journal of Mechanical Engineering Science and Technology (JMEST)

Indonesia is the world's largest archipelago country with a high potential for economic development and top producer and exporter of palm oil. As an archipelago country, the most efficient cargo transportation routes are through rivers and seas. Designing and building tankers, taking into account the specifics of the operation, are relevant. The paper considers the issues of designing a tanker for the transportation of crude palm oil with a defined operation area and route. The general concept of the vessel is proposed, taking into account the restrictions on the navigation area and draft for operation in the river. Particular attention …

The Combustion Characteristics Of Calophyllum Inophyllum Fuel In The Presence Of Magnetic Field, Imam Rudi Sugara, Nasrul Ilminnafik, Salahuddin Junus, Muh Nurkoyim Kustanto, Yuni Hermawan

Journal of Mechanical Engineering Science and Technology (JMEST)

The study objective is to investigate the combustion characteristics of Callophyllum inophyllum fuel in presence of a magnetic fields. To conduct the experiment, a bunsen burner was utilized, with fuel and air being dispensed via a syringe pump and compressor, both regulated by a flowmeter. The fuel and air pipes were heated to 532.15 (K) to facilitate fuel evaporation. The equivalent ratio of 0.5, 1, and 1.5 was adjusted to control air discharge and fuel. An 11,000 gausses artificial magnet was used, with N-S, N-S, N-N, and SS being the various magnetic pole configurations. The study found that the magnetic …

Lap Joint On St.37 Steel Plate With Friction Welding Clamping Method, Widia Setiawan, Nugroho Santoso, Wiyadi Wiyadi, Muhammad Sulistiyo Aji, Rachmat Alamin, Achsan Tarmudi

Journal of Mechanical Engineering Science and Technology (JMEST)

Friction stir (FW) welding is a relatively fresh method that was created and has been continually refined and adapted to industrial applications due to its benefits. This approach for solid-state joining entails connecting the components at a temperature below their melting point and then heating them up. Clamp joint applications are widely used using external heating and hitting with high strength, but the clamped joints with the FW method are rarely done. The research studied the characteristic of clamped joints at various plate thicknesses using the FW method. In this study, 30 specimens were used in the form of a …