Materials Science and Engineering Commons^™

Structural Performance And Resiliency Of Reinforced Concrete Bridge Pier Columns, Multi-Column Piers, And Bridge Systems Subjected To Multiple Hazards – Fire, Collision, And Air Blast, Qusai Abdulkarim Alomari

Dissertations and Doctoral Documents, University of Nebraska-Lincoln, 2023–

Given their close proximity to traffic and improper employment of protective systems, bridges and bridge piers are vulnerable to multi-hazard events triggered by vehicle collisions coupled with correlated and cascading events, such as explosions and fires. Despite recent catastrophic incidents that have highlighted the profound consequences of these extreme demands, including substantial damage, adverse economic impact, and loss of life, there has been a notable lack of research investigating the performance of bridges and bridge structural components under the aforementioned multi-hazards. Furthermore, current bridge design codes do not address these events assuming that, after these destructive events, replacement of the …

Ionically Crosslinked Cellulose Nanocrystals By Metal Nitrates For The Preparation Of Stable Emulsions With Tunable Interface Properties, Joseph Batta-Mpouma, Gurshagan Kandhola, Jin-Woo Kim

Materials Science and Engineering Faculty Publications and Presentations

Biologically extracted cellulose nanocrystals (CNCs) are rod-like and amphiphilic materials with surface-exposed (hydrophilic sites) and hidden (hydrophobic sites) hydroxyl groups. These physicochemical characteristics make CNCs suitable for use as emulsifying agents to stabilize emulsions. Stable oil-in-water emulsions, using sulfated (i.e., – SO₃−) CNCs that were ionically crosslinked with alkaline-earth (i.e., Mg ²⁺) or transition-d-block (i.e., Zn ²⁺) metal cations, were developed without the use of any synthetic surfactants or prior functionalization of pure CNCs with hydrophobic molecules. Various emulsion surface properties such as interfacial tension, surface charge, surface chemistry, as well as rheology were characterized. Ionically …

Microstructure, Mechanical Properties And Oxidation Behavior Of Refractory Multi-Principal Element Alloys By Laser Remelting And Conventional Manufacturing, Visharad Jalan, Seth Crawford, Sung Heng Wu, Frank Liou, Haiming Wen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Refractory multi-principal element alloys (RMPEAs), HfNbTaTiZr, (HfNbTaTiZr)9Cr, and (HfNbTaTiZr)9Al, were manufactured using vacuum arc melting followed by laser remelting to mimic additive manufacturing. the microhardness of the as-cast HfNbTaTiZr, (HfNbTaTiZr)9Cr, and (HfNbTaTiZr)9Al samples after arc melting was measured as 6.20, 7.63, and 6.89 Gpa, respectively. after laser remelting and re-solidification, the hardness increased by ~ 30% for each composition; the hardest was (HfNbTaTiZr)9Cr measured at 9.60 GPa, while the softest was HfNbTaTiZr with a hardness of 8.42 GPa, which was still harder compared to all the other samples. the addition of Al and Cr led to enhanced oxidation resistance for …

Data-Driven Multiscale Modeling Of Dye Aggregates In Dna For Excitonic Applications, Austin Biaggne

Boise State University Theses and Dissertations

In this dissertation, a data-driven, multi-scale approach was implemented to study the structural, electronic, and dynamical behavior of dye monomers and aggregates for excitonic applications. The excitonic behavior of dye aggregates depends on both the constituent monomer properties as well as the relative dye orientations that make up the aggregate. Dye monomer properties can be augmented with substituents, but with a wide range of substituent types, ideal dye derivatives should be identified. To control the aggregation of dyes, DNA can be used as a scaffold, however, the ways in which dyes interact with each other and with DNA is not …

Novel Sensors And Measurement Techniques For Thermal Properties In Extreme Environments, Katelyn Wada

Boise State University Theses and Dissertations

Advancements in thermal properties analysis is crucial for improvement of existing and next generation reactors, space exploration, and environmental safety. Extreme environments pose a great hurdle for instrumentation to measure real time thermal properties due to the extreme temperatures, high radiation, and variable electromagnetic environments. Nevertheless, measurement systems are tremendously important for the design, P.E.rformance, and safety considerations of nuclear fuels, space crafts, and deep sea/deep earth drilling. Thermal properties may change significantly in these environments creating challenging problems for temperature and thermal conductivity measurement systems. A recent focus has surrounded improvements in such systems for accurate determination of temperature …

Molecular Control Of Triplet-Pair Spin Polarization And Its Optoelectronic Magnetic Resonance Probes, Obadiah G. Reid, Justin C. Johnson, Joel D. Eaves, Niels H. Damrauer, John E. Anthony

Chemical and Materials Engineering Faculty Publications

Preparing and manipulating pure magnetic states in molecular systems are the key initial requirements for harnessing the power of synthetic chemistry to drive practical quantum sensing and computing technologies. One route for achieving the requisite higher spin states in organic systems exploits the phenomenon of singlet fission, which produces pairs of triplet excited states from initially photoexcited singlets in molecular assemblies with multiple chromophores. The resulting spin states are characterized by total spin (quintet, triplet, or singlet) and its projection onto a specified molecular or magnetic field axis. These excited states are typically highly polarized but exhibit an impure spin …

Advancing Additive Manufacturing For Biomedical Applications: Antimicrobial And X-Ray Absorptive Composite Filaments For Fused Filament Fabrication, John M. Arnold Jr

LSU New Orleans Theses and Dissertations

The objective of this research was to investigate the use of nano- and microparticle amendments for the creation of Poly-lactic Acid composite materials for use in biomedical applications using the Fused Filament Fabrication process of Additive Manufacturing. Composites were created with the goal of imparting the useful properties of antimicrobial activity and x-ray absorption to the material. In addition to testing the efficacy of the particle amendments in achieving the desired properties, the thermal and mechanical properties of the composite materials were tested to ensure that the composites would be compatible with the Fused Filament Fabrication process and would produce …

Sustainable Diamond-Like Carbon Fabricated Gravure Cylinders For Printing Fine Lines Of Electrodes And Graphic Structures, Chandramohan Seetharamiah Srinivasaraju

Dissertations

The main objective of this work is to evaluate the potential of Diamond-Like Carbon (DLC) as an alternative to chrome for use on gravure cylinders. DLC coatings consist of carbon atoms, arranged into a diamond-like structure that closely resembles that of natural diamond. In contrast to chrome, DLC is environmentally friendly. The focus of the study is to determine the viability of DLC as a substitute material for chrome to be used on gravure cylinders by determining key material properties and evaluating printing performance.

In the first research paper, four DLC variants (Standard DLC, A-DLC, S-DLC, and Organic Silica) and …

Exploring The Potential Of Tesla Valve For Filtering And Sorting Microscale Active Swimmers: A Computational Study, Ariel Rogers, Zhiyao He, Yong Wang

Physics Faculty Publications and Presentations

It is well-known that a Tesla valve allows fluids to flow unidirectionally without moving parts; however, how Tesla valves interact with active matters and the potential applications of Tesla valves in biology remain largely unexplored. Here, we present a computational study on the potential use of Tesla valves for filtering and sorting microscale active swimmers such as bacteria. We investigated the behavior of microscale swimmers passing through the Tesla valve at different linear and angular velocities using numerical simulations and quantified the diodicity of the Tesla valve for active swimmers. Our results demonstrate that the Tesla valve can effectively filter …

The Shape Modulation Of Laser-Induced Nanowelded Microstructures Using Two Colors, Ariel Rogers, Isabelle Niyonshuti, Jun Ou, Diksha Shrestha, Deborah Okyere, Jingyi Chen, Yong Wang

Physics Faculty Publications and Presentations

The light-based nanowelding of metallic nanoparticles is of particular interest because it provides convenient and controlled means for the conversion of nanoparticles into microstructures and the fabrication of nanodevices. In this study, we investigated the wavelength dependence of laser-induced nanowelded shapes of silver nanoparticles (AgNPs). We observed that the nanowelded microstructures illuminated with only a 405 nm laser were more branched than those formed via illumination using both the 405 nm and 532 nm lasers. We quantified this observation by two compactness descriptors and examined the dependence of the power of the 532 nm laser. More importantly, to understand the …

Role Of Mechanical Signaling In Bone Tissue, Scott Aaron Birks

Boise State University Theses and Dissertations

As the global population ages and life expectancy continues to rise, osteoporosis continues to be a growing worldwide health concern. The International Osteoporosis Foundation reports 1 in 3 women over the age of 50 years and 1 in 5 men worldwide will experience osteoporotic fractures in their lifetime, costing between 5 and 6.5 trillion USD annually in Canada, Europe, and the United States alone. The need for preventative measures to reduce age-related bone loss is clear, not only to improve quality of life for countless individuals but also to relieve the economic burden this condition imposes.

Exercise is a proven …

Investigating The Influence Of Surface Finishing Methods On Corrosion Of Additively Manufactured Ss316l, Joshua R. Fadeley

Boise State University Theses and Dissertations

Additive Manufacturing (AM), namely with metal, has seen a surge in growth and interest over recent years. A wide array of industries is developing new products to take advantage of this budding technology. In order to enable adoption of this technology, understanding of the differences of AM versus traditional manufacturing on the resultant materials properties of printed components is important. The work done for this study fell into two separate categories of work.

The first effort of this work involved the installation, certification, and operation of the first laser powder bed fusion (LPBF) printer at the Center for Advanced Energy …

Additive Manufacturing Of Microelectronic Devices For Extreme Environments, Nicholas Mckibben

Boise State University Theses and Dissertations

This work encompasses a comprehensive exploration of advanced manufacturing techniques for fabricating microelectronic devices compatible with extreme environments. The research integrates the fields of chemistry, nanomaterials, and additive manufacturing to achieve remarkable progress in sensor development, with a particular emphasis on aerosol jet printing (AJP), surface acoustic wave (SAW) devices, patterned graphene growth, and surface functionalization. The investigation begins with the AJP process development of a commercial silver nanoparticle ink, culminating in the fabrication of a piezoelectric SAW transducer that was prototyped as a high-temperature thermometer, showing excellent linearity when validated to 200°C. Next, the investigation continued with the development …

Design And Characterization Of A Novel Eef2k Degrader With Potent Therapeutic Efficacy Against Triple-Negative Breast Cancer, Changxin Zhong, Rongfeng Zhu, Ting Jiang, Sheng Tian, Xiaobao Zhao, Xiaoya Wan, Shilong Jiang, Zonglin Chen, Rong Gong, Linhao He, Jin-Ming Yang, Na Ye, Yan Cheng

Markey Cancer Center Faculty Publications

Dysregulated eEF2K expression is implicated in the pathogenesis of many human cancers, including triple-negative breast cancer (TNBC), making it a plausible therapeutic target. However, specific eEF2K inhibitors with potent anti-cancer activity have not been available so far. Targeted protein degradation has emerged as a new strategy for drug discovery. In this study, a novel small molecule chemical is designed and synthesized, named as compound C1, which shows potent activity in degrading eEF2K. C1 selectively binds to F8, L10, R144, C146, E229, and Y236 of the eEF2K protein and promotes its proteasomal degradation by increasing the interaction between eEF2K and the …

A Comprehensive Review On Metal Oxide-Nanocellulose Composites In Sustainable Active And Intelligent Food Packaging, Kalpani Y. Perera, Amit Jaiswal, Swarma Jaiswal, Dileswar Pradhan

Articles

The aim of this article is to provide an overview of the potential advantages and drawbacks of nanocellulose and metal oxide-based composites in food packaging. These materials offer improved mechanical and barrier properties, as well as antioxidant and antimicrobial benefits that extend the shelf life of food products. Nanocomposite structures protect food from various physiological factors and immobilize enzymes, while metal oxide nanoparticles provide antibacterial effects against Gram-positive and Gram-negative bacteria. However, there are concerns regarding the safety of nanoparticles and their potential migration into packaged food during processing and storage. This article explores these issues and highlights the need …

Engineered Biomass-Derived Carbon Adsorbents For Targeted Contaminant Remediation From Aqueous Environments, Suraj Venkat Pochampally

UNLV Theses, Dissertations, Professional Papers, and Capstones

Porous carbon adsorbents like biochar (BC) are produced from waste biomasses like wood chips, animal litter, nut shells, dried grass, etc. to be used in a multitude of applications like gas capture, soil amendment, water treatment, electrode materials, etc. In water treatment, carbon-based adsorbents have been mainly used to physically or chemically adsorb contaminants depending on the adsorption mechanism. However, BCs in their raw state do not have the capability of absorbing high amounts of contaminants and need to be activated/ modified for the pore network to broaden and adsorb the contaminants with better efficiency.

The scope of this dissertation …

Experimental Analysis Of Nonlinear Wave Propagation In Bistable Mechanical Metamaterials With A Defect, Samuel R. Harre

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Mechanical metamaterials built up of compliant units can support the propagation of linear and nonlinear waves. A popular architecture consists of a one-dimensional chain of bistable elements connected by linear springs. This type of chain can support nonlinear transition waves that switch each element from one stable state to the other as they propagate along the chain. One way to manipulate the propagation of such waves is via introduction of a local inhomogeneity, i.e., a defect in the otherwise periodic chain. Recent analytical and numerical work has shown that based on its initial velocity, a transition wave may be reflected, …

Synergistic Strategies In Sinter-Based Material Extrusion (Mex) 3d Printing Of Copper: Process Development, Product Design, Predictive Maps And Models., Kameswara Pavan Kumar Ajjarapu

Electronic Theses and Dissertations

3D printing pure copper with high electrical conductivity and exceptional density has long been challenging. While laser-based additive manufacturing technologies suffered due to copper's highly reflective nature towards laser beams, parts printed via binder-assisted technologies failed to reach over 90% IACS (International Annealed Copper Standard), electrical conductivity. Although promising techniques such as binder jetting, filament, and pellet-based 3D printing that can print copper exist, they however still face difficulties in achieving both high sintered densities and electrical conductivity values. This is due to a lack of comprehensive understanding of property evolution from green to sintered states and the strategies that …

3d Printed Microdialysis-Based Microsampling Probes, Patrick Pysz

Graduate Theses and Dissertations

This work will show the development of a fully 3D printed device platform in which a complex microsampling probe geometry is fabricated in a simple two-step process. This process includes the combination of 2-photon polymerization (2PP) and masked-stereolithography (MSLA). The cutting edge neurotechnology needed to monitor brain internal communication and will require multiple sensing modalities including temperature, pressure, electrophysiological, and optogenetics. Microsampling is an integrally important function for any future biosensing device platform as it allows for chemical delivery and unparalleled specificity through offline analysis of collection samples. Stereolithography (SLA) 3D printing has emerged as a powerful fabrication method capable …

Temperature Gradient Effect On Solid-Liqid Interface Properties Of Al-Cu Alloy: A Molecular Dynamics Study, Prashant Kumar Jha

All Theses

Aluminum-copper (Al-Cu) alloys are widely used in the aerospace industry due to their favorable strength-to-weight ratio, good fatigue resistance, and corrosion resistance. These properties make Al-Cu alloys an excellent choice for aircraft structural components that require high strength and low weight. Additive manufacturing (AM), also known as 3D printing, has emerged as a promising processing method for Al-Cu alloys in aerospace manufacturing. AM enables the production of lightweight optimized geometries difficult to manufacture through conventional subtractive methods. AM also reduces material waste by only depositing material where needed in the part geometry. The rapid solidification conditions in AM processes motivate …