Other Materials Science and Engineering Commons^™

Enhanced Hot Electron Lifetimes In Quantum Wells With Inhibited Phonon Coupling, Hamidreza Esmaielpour, Vincent R. Whiteside, Herath P. Piyathilaka, Sangeetha Vijeyaragunathan, Bin Wang, Echo Adcock-Smith, Kenneth P. Roberts, Tetsuya D. Mishima, Michael B. Santos, Alan D. Bristow, Ian R. Sellers

Faculty & Staff Scholarship

Hot electrons established by the absorption of high-energy photons typically thermalize on a picosecond time scale in a semiconductor, dissipating energy via various phonon-mediated relaxation pathways. Here it is shown that a strong hot carrier distribution can be produced using a type-II quantum well structure. In such systems it is shown that the dominant hot carrier thermalization process is limited by the radiative recombination lifetime of electrons with reduced wavefunction overlap with holes. It is proposed that the subsequent reabsorption of acoustic and optical phonons is facilitated by a mismatch in phonon dispersions at the InAs-AlAsSb interface and serves to …

Development Of Oxide-Dispersion-Strengthened Nickel-Based Super Alloy Powders For Additive Manufacturing, Sizhe Huang

Graduate Theses, Dissertations, and Problem Reports (ETD)

Oxide-Dispersion-Strengthened (ODS) Nickel-Based superalloy has been drawn a huge attention and developed with good oxidation resistance, corrosion resistance and high creep strength. It has been considered as critical materials for Additive Manufacturing (AM). The quality and the efficiency of fabrication methods of ODS limits the performance of itself on AM. The development of new type of ODS, new methodologies and evaluation techniques are required if the enhanced quality of ODS and enhanced efficiency of fabrication are to be achieved. Of the current fabrication techniques for AM, Gas Atomization (GA) is widely used since they can generate spherical powders with high …

The Influence Of Organic Pigments On Coating Properties, Sarah Medeiros

Williams Honors College, Honors Research Projects

Abstract

The purpose of this project was to identify the qualities of two synthesized organic pigments added to a coating. These high-performance pigments were benzodipyrrolidone and benzodifuranone, which are π-conjugated monomers. These pigments were each formulated into two different pigment concentrations and compared with a control that had no pigment. This project is limited by time constraints and the number of variables that can be tested in that time. Performance testing was conducted to evaluate the qualities of these coatings. The results demonstrated that the coatings were reproducible and most tests had results that were equal to or exceeded the …

Interfacial Corrosion Of Copper And The Formation Of Copper Hydroxychloride, Mary Teague, Shengxi Li, Hongbo Cong

Williams Honors College, Honors Research Projects

Electrical circuitry is an industry, among many others, heavily using the element of copper. Ensuring the mechanical integrity of Cu is crucial, especially in salt environments, for the multifaceted composition of circuits. 4N NaCl solution (equilibrium concentration in ~84% RH) simulated this three-phase system. Rectangular Cu samples were partially immersed in both ambient and continuous lab air sparging atmospheres to understand waterline corrosion of the metal. Open circuit potentials (OCP) were continuously taken during the immersion testing for a maximum of 5 days. A scanning electron microscopy (SEM) equipped with an energy dispersive X-ray spectrometer (EDS), Raman spectroscopy, and 3-D …

Design Of Shape-Conforming Nosecone For Optimal Fluid Flow From Transonic To Supersonic Range, Anna Tombazzi

Williams Honors College, Honors Research Projects

Modern flight vehicles, such as rockets, missiles, and airplanes, experience a force caused by forebody wave drag during the flight. This drag force is induced when the frontal point of each vehicle breaks the pressure wave during flight. Efforts to reduce this wave drag force to improve flight efficiency include modifying the nosecone profile of the flight vehicles to lower the drag force.

This project revolved around creating a design to make the transformation of nosecone shapes from a ¾ Parabolic profile to a ½ Power Series profile possible, mid-flight. Using a novel nosecone assembly, shape memory alloys (SMAs) and …

3d Printing – An Insider’S Perspective, Siddharth Sah

The Transdisciplinary STEAM+ Journal

The 3D printing market globally is still at its infancy, - or some might argue that there isn’t really a market yet. The knowledge of 3D printing design is still largely limited to engineering design – not product design. At MakeWhale, we are constantly pushing the boundaries of the application of 3D printing technology to consumer products resulting in a beautiful mix of technology and art.

Design, Analysis, And Application Of A Cellular Material/Structure Model For Metal Based Additive Manufacturing Process., Shanshan Zhang

Electronic Theses and Dissertations

Powder bed fusion additive manufacturing (PBF-AM) has been broadly utilized to fabricate lightweight cellular structures, which have promising potentials in many engineering applications such as biomedical prosthesis, aerospace, and architectural structures due to their high performance-to-weight ratios and unique property tailorabilities. To date, there is still a lack of adequate understanding of how the cellular materials are influenced by both the geometry designs and process parameters, which significantly hinders the effective design of cellular structures fabricated by PBF-AM for critical applications. This study aims to demonstrate a cellular structure design methodology that integrates geometrical design and process-material property designs. Utilizing …

A Study Of Manganese And Cobalt Incorporated Nickel Oxide Based Core-Shell Magnetic Nanoparticles, Samiul Hasan

Graduate Theses/Dissertations

The synthesis along with the structural and magnetic properties of manganese (Mn) and cobalt (Co) -incorporated nickel oxide (NiO) inverted core-shell nanoparticles (CSNs) were investigated. The primary objective of this study was to determine the effect of substitution of nickel (Ni) by transition metal ions (Mn²⁺/Co²⁺) in affecting the magnetic properties of the resultant CSNs. The core of the CSNs is comprised of NiO and the shell constitutes a Ni_x(Mn/Co)_1-xO phase. The synthesis of the CSNs was accomplished in two steps: first, NiO nanoparticles were synthesized using a thermal decomposition method. In …

Thermodynamics And Kinetics Of Dna Origami Cross-Tile Array Formation, Brett Michael Ward

Boise State University Theses and Dissertations

As the cost to continue scaling photolithography to pattern smaller semiconducting devices increases exponentially, new materials and fabrication approaches are being sought to extend and enhance current capabilities. DNA nanostructures have been identified as a promising material for patterning nanoscale devices, and several studies have demonstrated the ability to program DNA nanostructures to self-assemble into large scale arrays. These DNA arrays can be designed to create the patterns necessary for fabricating semiconductor device features. However, these structures are far from ideal and contain a number of defects that limit the adoption of this approach for manufacturing. In order to create …

Effects Of The Internal Magnetic Field On The Magneto-Mechanical Properties Of Magnetic Shape Memory Alloys, Anthony Hobza

Boise State University Theses and Dissertations

Shape memory alloys are a class of functional material which recover from large strains without permanent deformation. The strain is accommodated by the displacement of twin boundaries in the martensite phase. The shape memory alloy Ni-Mn-Ga is also ferromagnetic. Ni-Mn-Ga preferentially magnetizes along a certain crystallographic axis. This direction of easy magnetization changes across twin boundaries, such that the directions in neighboring twin domains are nearly perpendicular.

The interaction of magnetic moments and interfaces including the crystal surface and twin boundary interfaces has a large role in the magnetization process of the material. The goal of this study is to …

Bridge Build, Andrew Little

Student Scholarship

Bridge build design that includes not only a building process, but a research paper to make the best build possible as well.

Investigating Scalable Manufacturing Of High-Conductivity Wires And Coatings From Ultra-Long Carbon Nanotubes, Pouria Khanbolouki

Mechanical Engineering ETDs

Carbon nanotubes (CNTs) are a promising candidate for next generation of electrical wirings and electromagnetic interference (EMI) shielding materials due to their exceptional mechanical and electrical properties. Wires and coatings from ultralong nanotubes that are highly crystalline, well-aligned and densely packed can achieve this goal. High-performance CNT conductors will be relatively lightweight and resistant to harsh conditions and therefore can potentially replace current conductors in many industries including aerospace, automotive, gas and oil.

This thesis investigates a new manufacturing approach, based on conventional solution coating and wire drawing methods, to fabricate high conductivity wires and coatings from ultra-long carbon nanotubes. …

Nano/Submicro-Structured Iron Cobalt Oxides Based Materials For Energy Storage Application, Hongyan Gao

Masters Theses & Specialist Projects

Supercapacitors, as promising energy storage devices, have been of interest for their long lifespan compared to secondary batteries, high capacitance and excellent reliability compared to conventional dielectric capacitors. Transition metal oxides can be applied as the electrode materials for pseudocapacitors and offer a much higher specific capacitance. Co3O4 is one of the most investigated transition metal oxides for supercapacitor. Besides simple monometallic oxides, bimetallic transition oxides have recently drawn growing attention in electrochemical energy storage. They present many unique properties such as achievable oxidation states, high electrical conductivities because of the coexistence of two different cations in a single crystal …

Microstructure Evolution During Compaction Of Powder Blends, Ayush Giri, Marcial Gonzalez, Yasasvi Bommire

The Summer Undergraduate Research Fellowship (SURF) Symposium

Powder compaction is a manufacturing technology used to transform powder particles into a solid material with unique anisotropic microstructure and low porosity. It is widely used by pharmaceutical companies to manufacture tablets with desired properties. These properties are the result of the microstructure obtained during the compaction process. Therefore, it is imperative to understand the mechanics underneath the constituent granular particles that eventually contribute to properties of the manufactured tablets. Computational simulation tools have been developed in the past to study powder compaction for pharmaceutical tablets. However, most of the already existing tools limit their scope to study individual particles …

Investigating Tantalum As A Plasma-Facing Component For Nuclear Fusion Reactors, Arvind Sundaram, Jitendra K. Tripathi, Theodore J. Novakowski, Ahmed Hassanein Ph. D.

The Summer Undergraduate Research Fellowship (SURF) Symposium

Nuclear fusion is a potential source for producing unlimited environment-friendly energy. Tungsten (W) is selected as the primary candidate material for plasma facing component in nuclear fusion reactors due to its high melting temperature (3695 K), low sputtering erosion yield and strong mechanical properties. However, recent investigations on W have confirmed that it undergoes severe surface morphology changes during low energy He plasma and/or ion irradiation similar to a harsh fusion environment. Additionally, our previous studies indicate that tantalum (Ta) may show better resistance to the harsh radiation environment and is therefore worthy of investigation. Hydrogen retention properties, specifically deuterium …

Simulating Dynamic Failure Of Polymer-Bonded Explosives Under Periodic Excitation, Rachel Kohler, Camilo Duarte Cordon, Marisol Koslowski

The Summer Undergraduate Research Fellowship (SURF) Symposium

Accidental mishandling of explosive materials leads to thousands of injuries in the US every year. Understanding the mechanisms behind the detonation process is crucial to prevent such accidents. In polymer-bonded explosives (PBX), high-frequency mechanical excitation generates thermal energy and can lead to an increase in temperature and vapor pressure, and potentially the initiation of the detonation process. However, the mechanisms behind this energy release, such as the effects of dynamic fracture and friction, are not well understood. Experimental data is difficult to collect due to the different time scales of reactions and vibrations, so research is aided by running simulations …

Modelling Catalytic Structures With Python And Ase, Tommie L. Day, Peilin Liao, Pilsun Yoo

The Summer Undergraduate Research Fellowship (SURF) Symposium

Voltaic cells hold great potential as a source of clean electricity generation. These fuel sources are more efficient than combustion engines, and they do not produce environmentally harmful by-products. The electrochemical reaction which occurs within the cell is typically catalyzed by platinum, which increases the cost. The search for a better performing, less expensive catalyst is hindered by the lack of a complete, predictive theory of catalysis. Using Quantum Espresso and the Atomic Simulation Environment library for Python, we created a tool for nanoHUB.org which can visually and computationally model catalytic surfaces. This tool can simulate nanoparticles and metallic surfaces …

Core-Shell Copper And Nickel Nanofoam: Uniform Electroplating And Properties, Hassan Zbib, David Bahr

The Summer Undergraduate Research Fellowship (SURF) Symposium

Characterizing materials on the nanoscale is a key factor to enhance nanotechnology in diverse applications, ranging from electronics to energy fields. However, controlling the structure of the material at the nanoscale or mimicking the nanoscale features of a structure that already exists requires linking processing conditions to the nanostructure. This work focuses on solids that show porous patterns at the nano-micro scale; these are often called cellular solids and classified into two categories: honeycombs and foams. This study focuses on nanofoams; with ligament dimensions in the sub-micron scale. Electrospinning has been developed to produce nanofoam structures of polymers with controlled …

Viscoelastic Analysis And Fatigue Characterization Of Bituminous Materials In Two Length Scales Under The Influence Of Aging, Santosh Reddy Kommidi

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Fatigue cracking in asphalt concrete (AC) is of immense importance to pavement design and analysis because it is one of the most important forms of distress that can lead to structural failure in pavement. Once started, these types of cracks can be combined with other environmental factors leading to detrimental effects such as faster rates of pavement deterioration and shortened pavement life and functionality.

Currently AASHTO TP101, also known as linear amplitude sweep (LAS) specification, is being widely used to evaluate the ability of an asphalt binder to resist fatigue. The LAS method, although mechanistic in its approach, has certain …

The Mechanism Of Radiation-Induced Nanocluster Evolution In Oxide Dispersion Strengthened And Ferritic-Martensitic Alloys, Matthew John Swenson

Boise State University Theses and Dissertations

The objective of this study is to evaluate the mechanism of irradiation-induced nanoparticle evolution in a model Fe-9%Cr oxide dispersion strengthened steel and commercial ferritic-martensitic alloys HCM12A and HT9. Each alloy is irradiated with Fe²⁺ ions, protons, or neutrons to doses ranging from 1-100 displacements per atoms at 500°C. The morphology of nanoclusters are characterized using atom probe tomography. The evolution of clusters in each alloy are notably different with each irradiating particle, and the competing effects of ballistic dissolution and radiation-enhanced, diffusion-driven growth are attributed to the respective differences in cluster evolution. A phase evolution model, originally theorized …