Other Materials Science and Engineering Commons^™

Fast-, Light-Cured Scintillating Plastic For 3d-Printing Applications, Brian G. Frandsen, Michael Febbraro, Thomas Ruland, Theodore W. Stephens, Paul A. Hausladen, Juan J. Manfredi, James E. Bevins

Faculty Publications

Additive manufacturing techniques enable a wide range of possibilities for novel radiation detectors spanning simple to highly complex geometries, multi-material composites, and metamaterials that are either impossible or cost prohibitive to produce using conventional methods. The present work identifies a set of promising formulations of photocurable scintillator resins capable of neutron-gamma pulse shape discrimination (PSD) to support the additive manufacturing of fast neutron detectors. The development of these resins utilizes a step-by-step, trial-and-error approach to identify different monomer and cross-linker combinations that meet the requirements for 3D printing followed by a 2-level factorial parameter study to optimize the radiation detection …

Accurate Evaluation Of The Direction-Dependent Mechanical Properties Of Ideal Single Crystals: A Comparative Ab Initio Study, Jaylan Ali Elhalawani

Theses and Dissertations

The mechanical properties of a single crystal or a grain in a polycrystalline material are highly dependent on the direction of the applied load. Key properties of interest are the Young’s modulus and the Poisson ratio in the small strain limit, and the ideal tensile strength in the large strain regime. Prior atomistic computations of these properties interchangeably used two approaches. In one approach the stress-strain response is explicitly calculated via a numerical tensile test experiment. In the second approach the second order single crystal elastic constants are computed via small deformations and then used in analytical equations to derive …

Atomistic Simulation Studies Of Thin Film Growth And Plastic Deformation In Metals And Metal/Ceramic Nanostructures, Reza Namakian

LSU Doctoral Dissertations

Despite the significant improvements in manufacturing and synthesis processes of metals and ceramics in the past decades, there are still areas in which the procedure is still frequently more of an art or skill rather than a science. Therefore, systematic and combined experimental and computational studies are required to facilitate the development of techniques that offer thorough understanding of the events taking place during manufacturing and synthesis processes. With regard to these issues, it is paramount to address microscale characterizations and atomic scale understanding of the events during fabrication processes. One of the focuses of this study is unraveling fundamental …

Nanoclays‑Containing Bio‑Based Packaging Materials: Properties, Applications, Safety, And Regulatory Issues, Kalpani Y. Perera, Maille Hopkins, Amit K. Jaiswal Dr, Swarna Jaiswal

Articles

Food packaging is an important concept for consumer satisfaction and the increased shelf life of food products. The introduction of novel food packaging materials has become an emerging trend in recent years, which could be mainly due to environmental pollution caused by plastic packaging and to reduce food waste. Recently, numerous studies have been carried out on nanoclays or nanolayered silicate to be used in packaging material development as reinforcing filler composites. Different types of nanoclays have been used as food packaging materials, while montmorillonite (MMT), halloysite, bentonite (BT), Cloisite, and organically modified nanoclays have become of great interest. The …

Launching A 3d Printing Program For Students: Recommendations And Best Practices For Libraries, Wilhelmina Randtke, Lee Bareford

Georgia Library Quarterly

The Georgia Southern University Libraries launched a 3D printing program for students in July 2022. Prior to launch, library employees at two of Georgia Southern University’s campuses investigated options for implementing safe, affordable, and sustainable 3D printing in existing academic libraries without retrofitting costly ventilation systems into existing facilities. This article describes the reasons why the Georgia Southern University Libraries thought that a 3D printing program could fulfill a service need for students across university colleges and departments and outlines some of the challenges, best practices, and unique innovations that the library’s employees experienced throughout the program launch process. The …

Adsorptive Properties And On-Demand Magnetic Response Of Lignin@Fe3o4 Nanoparticles At Castor Oil–Water Interfaces, Mohammad J. Hasan, Emily Westphal, Peng Chen, Abishek Saini, I-Wei Chu, Sarah J. Watzman, Esteban E. Ureña-Benavides, Erick S. Vasquez

Chemical and Materials Engineering Faculty Publications

Lignin@Fe3O4 nanoparticles adsorb at oil–water interfaces, form Pickering emulsions, induce on-demand magnetic responses to break emulsions, and can sequester oil from water. Lignin@Fe3O4 nanoparticles were prepared using a pH-induced precipitation method and were fully characterized. These were used to prepare Pickering emulsions with castor oil/Sudan red G dye and water at various oil/water volume ratios and nanoparticle concentrations. The stability and demulsification of the emulsions under different magnetic fields generated with permanent magnets (0–540 mT) were investigated using microscopy images and by visual inspection over time. The results showed that the Pickering emulsions were more stable at the castor oil/water …

Liquid-Liquid Equilibria Of Water + Ethanol + Castor Oil And The Effect Of Cellulose Nanocrystal/Fe3o4 And Lignin/Fe3o4 Nanoparticles, Mohammad J. Hasan, Fariba Yehaneh, Amy Ciric, Peng Chen, Erick S. Vasquez, Esteban E. Ureña-Benavides

Chemical and Materials Engineering Faculty Publications

Castor oil has been proposed as a renewable solvent for the liquid extraction of ethanol from water as an alternative to more traditional energy intensive distillation-based methods. The liquid–liquid equilibrium (LLE) of the ternary system water + ethanol + castor oil was determined at 295.15 K using high performance liquid chromatography (HPLC). Castor oil was herein treated as a pseudo-component with the molecular weight of the triglyceride of ricinoleic acid. The experimental data was fitted to the UNIQUAC and NRTL models to obtain parameters for castor oil, and binary interaction parameters for castor oil/ethanol and castor oil/water pairs. The separation …

Investigation Of Fiber Orientation And Mechanical Properties Of Pyrolysis Recycled Carbon-Fiber Reinforced Thermoset Composite, Reva N. Simmons, Harry Lee, Garam Kim

Discovery Undergraduate Interdisciplinary Research Internship

With increasing demand of carbon fiber reinforced fiber thermoset composites, establishing a sustainable cycle for these materials becomes crucial. Pyrolysis is a process of reclaiming carbon fiber from thermoset composites by thermally degrading the polymer at high temperatures allowing the fibers to be extracted. Carbon fiber reclaimed through current pyrolysis processes for thermoset composites typically loses its original shape and orientation, making it difficult to reorganize the fibers. This study investigated the feasibility of maintaining the fiber orientations for continuous fiber reinforced thermoset composite during pyrolysis by stitching the carbon fiber layup to a conformable copper mesh during the manufacturing …

Mechanical Design Of A Microwave Imaging Device For Breast Cancer Detection In Mri Scanners, Grace M. Player

Dartmouth College Master’s Theses

This project seeks to develop an updated version of a microwave imaging device for use in conjunction with breast MRI, improving upon existing technology and developing novel concepts for the device. It posits three primary redesign targets for updating the previous system: resizing the system height, making the device more iteration- friendly, and improving the overall manufacturability of the device by replacing custom components with commercially available alternatives. All three of these redesign targets are met in the new design, V2.0. The height is reduced by reducing antenna travel and height, embedding some components, and shortening the tank wall, resulting …

Aerosol Synthesis Of Tungsten Bronze Particles For Nir Shielding, Hao Tu

Theses and Dissertations

This dissertation emphasizes the need for efficient energy use in buildings and transportation due to global warming and the energy crisis. It suggests that improving energy efficiency can help reduce energy consumption and emissions and support sustainability. The dissertation introduces various transparent materials that can block near-infrared (NIR) radiation from solar radiation to save energy and money, and it highlights the growing market value of such products. The dissertation compares tungsten bronze with other NIR shielding materials and shows its advantages. The dissertation introduces a cheap and environmentally friendly method for continuously producing tungsten bronze particles via aerosol synthesis. Particle …

Preparation, Cure, And Characterization Of Cyanate Ester-Epoxy Blends Containing Reactive Flame Retardants, Mustafa Mukhtar, Donald A. Klosterman

Chemical and Materials Engineering Faculty Publications

Cyanate ester resins are sometimes mixed with lower cost epoxy monomers to modify cost, toughness, and processing capabilities. Despite the high performance of these thermosetting polymers, flame retardancy remains an issue. This study examined blends of three different commercial cyanate ester monomers (LVT-100, LECy, and XU-71787.02) and diglycidyl ether of bisphenol A (DGEBA) at 50/50 wt% of each type. The blends were successfully reacted with two reactive flame retardants (FR): 9,10-dihydro-9-ox-9-phosphaphenanthrene-10-oxide (DOPO) and poly(m-phenylene methylphosphonate) (PMP) at phosphorus contents ranging from 0 to 3 wt%. The curing behavior of EP/CE blends was investigated using differential scanning calorimetry (DSC). It was …

Development Of High Kinetic Inductance Superconducting Nanowire Devices On High Permittivity Strontium Titanate Substrates, Jamie Timmons

UNF Graduate Theses and Dissertations

This thesis involves the fabrication and characterization of devices made from two different superconducting materials: yttrium barium copper oxide (YBCO), a high-TC complex oxide, and niobium nitride (NbN), a low-TC transition metal nitride. Both types of devices are fabricated on strontium titanate substrates, which provides a good lattice match to YBCO and also an extremely large permittivity at low temperature. We demonstrate that wet etching of YBCO thin films via bromine can be a viable microfrabriation technique for the material. Using approximately 35 nm thick epitaxially grown YBCO on an STO substrate, we were able to fabricate YBCO “microwires” with …

Drop Wetting And Sliding On Soft, Swollen Elastomers, Zhuoyun Cai

Theses and Dissertations--Chemical and Materials Engineering

Soft, slippery surfaces have gained increasing attention due to their wide range of potential applications, for example in self-cleaning, anti-fouling, liquid collection, and more. One design approach in creating slippery surfaces is using a swollen elastomer, which is a polymer network swollen with a lubricant. This type of surface may be beneficial for longer-term use than standard lubricant-infused surfaces, and provides a versatile surface with tunable mechanical properties. Hence, understanding the physics of soft surface interactions is important for fundamental soft matter physics, biomaterials, adhesives, and coatings. This research experimentally investigates wetting on soft infused networks, with the aim of …

Development Of Interatomic Potential Of High Entropy Diborides With Artificial Intelligence Approach To Simulate The Thermo-Mechanical Properties, Nur Aziz Octoviawan

Graduate Theses/Dissertations

The interatomic potentials designed for binary/high entropy diborides and ultra-high temperature composites (UHTC) have been developed through the implementation of deep neural network (DNN) algorithms. These algorithms employed two different approaches and corresponding codes; 1) strictly local & invariant scalar-based descriptors as implemented in the DEEPMD code and 2) equivariant tensor-based descriptors as included in the ALLEGRO code. The samples for training and validation sets of the forces, energy, and virial data were obtained from the ab-initio molecular dynamics (AIMD) simulations and Density Functional Theory (DFT) calculations, including the simulation data from the ultra-high temperature region (> 2000K). The study …

A Study Of Synthesis And Characterization Of Naxmno2-Δ As A Cathode Material For Sodium-Ion Battery, Zia Uddin Mahmud

Graduate Theses/Dissertations

The proliferation of renewable energy sources and the promising market for net-scale battery applications immediately increases the need for electrochemical energy storage technology. Sodium (Na) components are more accessible and less expensive than lithium. Being a sodium-based material with a high-power density provided by Na-ion diffusion, Na_xMnO_{2- δ} is a strong contender for large-scale Sodium-ion-battery (SIB) applications. In the current study, Na_xMnO_{2- δ} is created using a solid-state reaction technique, and investigated structural, electrical, and electrochemical properties of materials were investigated using X-ray diffraction (XRD), Raman spectroscopy, scanning electron microscopy (SEM), UV-VIS spectroscopy, and …

Synthesis And Characterization Of Cage-Structured Compounds As Promising Thermoelectric Materials, Nusrat Yasmin

Graduate Theses/Dissertations

The development of new thermoelectric materials is of great interest due to their potential to convert waste heat into useful electricity. The primary problem is that the physical factors that are utilized to assess thermoelectric performance conflict with one another. One way to improve their performance is to hinder the lattice from conducting heat through its vibrations while maintaining the heat conduction via the electrons. This can be done by creating cage structures that allow heavy atoms to jiggle. In this study, we report the synthesis of a group of such compounds, using the self-flux method. They all belong to …

Study Of Nanocomposite Materials Using Molecular Dynamics, Prashik Sunil Gaikwad

Dissertations, Master's Theses and Master's Reports

There is an increase in demand for new lightweight structural materials in the aerospace industry for more efficient and affordable human space travel. Polymer matrix composites (PMCs) with reinforcement material as carbon nanotubes (CNTs) have shown exceptional increase in the mechanical properties. Flattened carbon nanotubes (flCNTs) are a primary component of many carbon nanotube (CNT) yarn and sheet materials, which are promising reinforcements for the next generation of ultra-strong composites for aerospace applications. These flCNT/polymer materials are subjected to extreme pressure and temperature during curing process. Therefore there is a need to investigate the evolution of properties during the curing …

Nanomaterials For Cardiovascular Engineering, Roya Bagheri

Dissertations, Master's Theses and Master's Reports

Cardiovascular diseases and disorders (i.e., those related to heart and blood vessels) are the main reasons for mortality worldwide. Nanomaterials, with their unique morphologies and properties, have a great potential for advancing cardiovascular engineering to treat diseases and disorders. In this dissertation, several cardiovascular applications of conductive nanomaterials were investigated. First, a conductive nanomaterial was explored to fabricate biohybrid nanomaterial-cardiomyocyte (CM – heart muscle cell) systems. Using Carbon Nanotube (CNT) forest as a 3D porous and conductive scaffold was investigated. The influence of the CNT forest on the viability, attachment, and spreading of CMs and their genetic information was …

Solid-State Shear Pulverization: A Comprehensive Study On Polymer Processing Technology From A Systematic Innovation Perspective, Tyler A. Will

Master’s Theses

Solid-state shear pulverization (SSSP) is a continuous and scalable processing technique that imposes mechanochemical changes in polymer-based materials. It has been shown to impart beneficial properties onto homopolymers or create copolymers and composites through continuous fragmentation and fusion. The unique technology employs cold temperature to keep the polymer in the solid state. This thesis investigates industrial polymer processing in the context of real-world applications. This thesis analyzes SSSP using an organized methodology called systematic innovation (SI). SI facilitates problem solving by assisting engineers in conducting root cause analysis around a material and studying the physical setup of the equipment.

This …

Recycling Metal Chips Into Usable Materials, Alex Mortensen, Ben Mortensen

Williams Honors College, Honors Research Projects

This report entails the scope, design considerations, and plans for creating a metal chip converter into metal briquettes. The construction is a set of machines with multiple processes to make the conversion happen. The process includes washing fine metal chips, drying them off, compressing them, and melting them down into usable briquettes. This project is intended to make a simple process to recycle metal chips into usable material for reuse. The project's objective is to reduce the costs of storage and recycling waste by offering a solution to recycle it into materials the shop can reuse.