Ceramic Materials Commons^™

Controlling Calcium Compound Formation In Biocompatible Materials For Tissue Regeneration And Repair In Mammals, Steven B. Jung, D. E. Day

Materials Science and Engineering Faculty Research & Creative Works

A biocompatible composition for tissue repair or regeneration in mammals comprising one or more glass former compounds selected from the group consisting of B₂O₃, P₂O₅, and SiO₂ and director elements selected from the group consisting of Cu, Sr, Zn, Fe, Mn, Cr, V, Nb, Mo, W, Ba, Co, S, Al, Ti, Y, Mg, Si and/or Ni to promote in vivo calcium compound formation of calcium carbonate or other calcium compounds other than hydroxyapatite. Upon direct application of the biocompatible composition to a mammalian host, calcium carbonate or other calcium compounds other …

Scaffold For Tissue Regeneration In Mammals, D. E. Day, Steven B. Jung, Roger F. Brown

Materials Science and Engineering Faculty Research & Creative Works

A three-dimensional scaffold with interconnected pores for repair of tissue comprising a scaffold body for structural support of the tissue scaffold, where the scaffold body comprises scaffold body components bonded to each other and made from component materials comprising about 40 to about 90 wt % B₂O₃, and two or more other oxides, wherein the scaffold body has a porosity between about 15 and about 90 vol %.

Quality Improvement In Drilling Silicon By Using Micro Laser Assisted Drilling, Barkin Bakir

The Hilltop Review

The micro-laser assisted drilling (µ-LAD) of monocrystalline silicon (100), using a diamond cutting tool coupled with a laser, was tested in order to improve the cutting edge quality of a drilled samples. The laser beam is transmitted through an optically transparent diamond drill bit and focused precisely at the tool-workpiece interface, where the material is under high pressure induced by the diamond tool. The influence of the laser power on the quality and the inner surface finish of the drilled materials is investigated. Different laser powers were used to carry out the experiments. The experimental results indicated that the µ-LAD …

Fabricating Zirconia Parts With Organic Support Material By The Ceramic On-Demand Extrusion Process, Wenbin Li, Amir Ghazanfari, Devin Mcmillen, Andrew Scherff, Ming Leu, Gregory Hilmas

Faculty Publications, Mechanical Engineering

Ceramic On-Demand Extrusion (CODE) is an extrusion-based additive manufacturing process recently developed for fabricating dense, functional ceramic components. This paper presents a further development of this process and focuses on fabricating 3 mol% yttria-stabilized zirconia (3YSZ) components that cannot be fabricated without using support structures. The 3YSZ paste is deposited through the main nozzle, and a polycaprolactone (PCL) pellet feedstock is melted and deposited through an auxiliary nozzle to build support structures. After a green part is printed and dried, the support structures are removed by heating the part to ~70°C to melt the PCL. The part is then sintered …

Nonlinear Dielectric Behavior Of Field-Induced Antiferroelectric/Paraelectric-To-Ferroelectric Phase Transition For High Energy Density Capacitor Application, Mingyang Li

Dissertations, Master's Theses and Master's Reports

Electric field-induced antiferroelectric(AFE)/paraelectric(PE)-to-ferroelectric(FE) phase transitions are investigated for the associated nonlinear dielectric behavior, which could offer high dielectric capacity. The phenomenon in monolithic materials has been computed for Kittel antiferroelectric and BaTiO₃ model systems using the Landau-Ginzburg-Devonshire theory. The general switching curves give values of the polarization as a function of external electric field. A similar computation is performed for particle-filled polymer-matrix composites where an internal depolarization field is considered. The polarization-electric field response changes with different depolarization factors, which demonstrate the shape and alignment of the dielectric particles embedded in polymer-matrix are key factors for the composite to …

Controlling Properties Of Agglomerates For Chemical Processes, Joseph A. Halt

Dissertations, Master's Theses and Master's Reports

Iron ore pellets are hard spheres made from powdered ore and binders. Pellets are used to make iron, mainly in blast furnaces. Around the time that the pelletizing process was developed, starch was proposed as a binder because it’s viscous, adheres well to iron oxides, does not contaminate pellets and is relatively cheap. In practice, however, starch leads to weak pellets with rough surfaces – these increase the amount of dust generated within process equipment and during pellet shipping and handling. Thus, even though the usual binder (bentonite clay) contaminates pellets, pelletizers prefer it to starch or other organics.

This …

Charge Transport In Electronic-Ionic Composites, Long Zhang

Theses and Dissertations--Chemical and Materials Engineering

The goal of this thesis is to generate fundamental understandings of charge transport behaviors of composites consisting of garnet structured Al substituted Li₇La₃Zr₂O₁₂ (LLZO) electrolyte and LiCoO₂ electrode. In order to take full advantage of all-solid-state batteries, bulk type composite electrodes should be introduced to increase energy and power density. However, the charge utilization of bulk type composite electrodes is quite low. Understanding ionic conduction behavior is, therefore, important for improving the performance of all-solid-state batteries, because ion conduction within solids depends on effective pathways. Electronic conductivity can be easily compensated by …

Mechanical Characterization Of Parts Produced By Ceramic On‐Demand Extrusion Process, Amir Ghazanfari, Wenbin Li, Ming Leu, Gregory Hilmas

Faculty Publications, Mechanical Engineering

Ceramic On‐Demand Extrusion (CODE) is an additive manufacturing process recently developed to produce dense three‐dimensional ceramic components. In this paper, the properties of parts produced using this freeform extrusion fabrication process are described. High solids loading (~60 vol%) alumina paste was prepared to fabricate parts and standard test methods were employed to examine their properties including the density, strength, Young's modulus, Weibull modulus, toughness, and hardness. Microstructural evaluation was also performed to measure the grain size and critical flaw size. The results indicate that the properties of parts surpass most other ceramic additive manufacturing processes and match conventional fabrication techniques.

Processing, Microstructure, And Properties Of Engineered Diboride Structures, Connor Charles Wittmaier

Masters Theses

"The mechanical properties and processing parameters of boride ceramics in foam and laminate architectures were evaluated. The ceramic reticulated foam was produced through a polymer substrate replication technique and the hardness and compressive strength were tested. The laminate structure was tested to evaluate the flexure strength and work of fracture as a function of temperature.

The foam architecture was produced using a TiB₂ slurry coating on a polyurethane reticulated foam preform. Foams sintered to 2150⁰C displayed an average grain size of 8.9 ± 7.3 µm, and a hardness of 17.3 ± 2.4 GPa. Crush testing foams were sintered at …

3d Bioprinting Of Stem Cells And Polymer/Bioactive Glass Composite Scaffolds For Bone Tissue Engineering, Caroline Murphy, Krishna Kolan, Wenbin Li, Julie A. Semon, D. E. Day, Ming-Chuan Leu

Biological Sciences Faculty Research & Creative Works

A major limitation of using synthetic scaffolds in tissue engineering applications is insufficient angiogenesis in scaffold interior. Bioactive borate glasses have been shown to promote angiogenesis. There is a need to investigate the biofabrication of polymer composites by incorporating borate glass to increase the angiogenic capacity of the fabri-cated scaffolds. In this study, we investigated the bioprinting of human adipose stem cells (ASCs) with a polycaprolac-tone (PCL)/bioactive borate glass composite. Borate glass at the concentration of 10 to 50 weight %, was added to a mixture of PCL and organic solvent to make an extrudable paste. ASCs suspended in Matrigel …

Viscous Sealing Glass Compositions For Solid Oxide Fuel Cells, Cheol-Woon Kim, Richard K. Brow

Nuclear Engineering and Radiation Science Faculty Research & Creative Works

A sealant for forming a seal between at least two solid oxide fuel cell components wherein the sealant comprises a glass material comprising B₂O₃ as a principal glass former, BaO, and other components and wherein the glass material is substantially alkali-free and contains less than 30% crystalline material.

Microstructure And Properties Of Spark Plasma Sintered Moalb Ceramics, Ting Lou

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Molybdenum aluminum boride (MoAlB) is a ternary transition metal boride which has promising aeronautic and nuclear applications. It inheres excellent properties of the binary transitional metal borides (e.g., MoB, ZrB₂) such as high melting temperature, high hardness, and thermal conductivity. Besides, MoAlB is superior to MoB because: (1) the Al element provides an oxidation resistance at high temperatures; (2) its nanolaminated structure consisting of M-B layers with alternating Al layers results in a unique damage tolerance property. In this research, polycrystalline MoAlB have been successfully synthesized and simultaneously sintered using spark plasma sintering (SPS) from molybdenum boride (MoB) …

Empirical Models For Structural Effects Of A-Site Point Defects And Ordering In Perovskites, Kevin Ross Tolman

Boise State University Theses and Dissertations

Composition-structure-property relationships are essential keys to unlocking the strength of predictive crystal chemistry. Awkwardly, the electroceramics industry largely relies on various time-consuming and expensive trial-and-error experiments to address new questions which often could otherwise be interpolated from published data. Indeed, predictive models, which can be derived from empirical evidence, can greatly aid the direction and support of future development in a meaningful, apt, and cost-effective way. Theory suggests that intrinsic properties on the scale of a unit cell may be estimated from the sizes and charges of the chemical constituents alone. Ultimately, researchers could be provided a compositional recipe for …

Nanoindentation Techniques For The Evaluation Of Silicon Nitride Thin Films, Weston T. Mangin

Master's Theses

Silicon nitride thin films are of interest in the biomedical engineering field due to their biocompatibility and favorable tribological properties. Evaluation and understanding of the properties of these films under diverse loading and failure conditions is a necessary prerequisite to their use in biomedical devices. Three wafers of silicon nitride-coated silicon were obtained from Lawrence Livermore National Laboratory and used to create 96 samples. Samples were subjected to nanoindentation testing to evaluate the mechanical properties of the film. Samples were subjected to nanoimpact testing to compare the damage resistance of the film to separate nanoimpact types. Samples were subjected to …

Method For Fabricating Biocompatible Porous Titanium, B. Sonny Bal, Tieshu Huang, M. N. Rahaman

Materials Science and Engineering Faculty Research & Creative Works

A method for fabricating porous metal constructs (such as porous Ti constructs) which may be used as implants in bone repair is disclosed. The method employs a new saltbath sintering process coupled with conventional powder metallurgy technology which is capable of fabricating porous metal constructs with controlled porosity and pore size having a lower production cost than conventional powder metallurgy methods.

Water-Soluble Glass Substrate As A Platform For Biodegradable Solid-State Devices, Shihab Md Adnan, Kwangman Lee, Mohammad Tayeb Ahmad Ghasr, Matthew O'Keefe, D. E. Day, Chang-Soo Kim

Materials Science and Engineering Faculty Research & Creative Works

A biodegradable glass material is utilized as a novel functional element of solid-state devices. A water-soluble borate glass substrate serves as the structural platform on which thin film device is built. The glass substrate completely dissolves in a saline solution in approximately 40 h. Intentional failure of the spiral device (RLC resonator circuit) as a result of rapid structural disintegration by dissolution is demonstrated in DC, AC, and RF ranges that agrees well with simulation. Adopting water-soluble glass elements is expected to be a viable approach to develop reliable all-inorganic biodegradable devices that are fully functional during an intended operational …

Investigation Of Electric Field–Induced Structural Changes At Fe-Doped Srtio3 Anode Interfaces By Second Harmonic Generation, David Ascienzo, Haochen Yuan, Steven Greenbaum, Thorsten J. Bayer, Russell A. Maier, Jian-Jun Wang, Clive A. Randall, Elizabeth C. Dickey, Haibin Zhao, Yuhang Ren

Publications and Research

We report on the detection of electric field–induced second harmonic generation (EFISHG) from the anode interfaces of reduced and oxidized Fe-doped SrTiO3 (Fe:STO) single crystals. For the reduced crystal, we observe steady enhancements of the susceptibility components as the imposed dc-voltage increases. The enhancements are attributed to a field-stabilized electrostriction, leading to Fe:Ti-O bond stretching and bending in Fe:Ti-O6 octahedra. For the oxidized crystal, no obvious structural changes are observed below 16 kV/cm. Above 16 kV/cm, a sharp enhancement of the susceptibilities occurs due to local electrostrictive deformations in response to oxygen vacancy migrations away from the anode. Differences between …

Numerical Simulation Of The Influence Of Ceramic Preform On The Infiltration Process Of Metal Matrix Composites, Chang-Chun Dong, Jian-Xin Zhou, Ya-Jun Yin, Xu Shen

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Wetting And Interfacial Microstructure Of Porous Si3n4/Si3n4 Joint After Silver Metallization, Yanli Zhuang, Tiesong Lin, Shengjin Wang, Peng He, Dusan P. Sekulic, Dechang Jia, Hongmei Wei

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Effect Of Post-Treatment On Micro-Structure And Properties Of Al2o3–13 Wt%Tio2 Plasma-Spray Coating, Zehua Zhou

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.