Engineering Science and Materials Commons^™

Hurricane Damage Assessment Process For Residential Buildings, Carol C. Massarra

LSU Master's Theses

Assessing an affected area immediately after a severe natural hazard event and saving the resulting data are vitally important in any effort to reduce future economic losses from natural hazards. These data are used as a record of buildings performance and as a major component for statistical analysis and damage modeling studies. Since these data are used as input for these studies, the data must be assessed and collected in a scientific and standardized way. Despite this requirement, neither a systematic damage assessment process nor a standardized data collection protocol is currently available in the United States to ensure that …

Quantification Of Nox Reduction Via Nitrate Accumulation On A Tio2 Photocatalytic Concrete Pavement, David James Osborn

LSU Master's Theses

Field trials of photocatalytic pavements were recently initiated and are presently being considered by many states (e.g., Virginia, Texas, New York, and Missouri). Results from this study originate from the country’s first air-purifying asphalt and concrete photocatalytic pavements, constructed on Dec. 20, 2010. The test area is a pavement site located on the LSU campus. The objective of the study is to validate field photocatalytic degradation of NOx in a field environment by measuring the day to day accumulation of the oxidized byproduct; nitrate salts. The mass of nitrates, produced by the real life photocatalytic pavement, were measured. The measurement …

A Basic Understanding Of Rapid Mold Surface Heating Via Laser Energy, Charles Daniel Fox

Browse all Theses and Dissertations

As the research and development of surface heating methods have increased in the recent years, the consensus has been reached amongst the injection molding community that an elevated mold surface temperature near or greater than the polymer solidification temperature provides acceptable replication of the desired micro-structured parts. The laser heating experimental work and simulation development carried out includes two sample sizes similar to those used in injection molding. A 100W CO2 laser incident on three samples of different surface roughnesses has shown to have elevated temperatures via thermal cameral data and thermocouple measurements. Among five different laser spot sizes varying …

Thickness-Shear And Thickness-Twist Modes In An Oblate Elliptical Ceramic Cylinder And Energy Trapping In Contoured Acoustic Wave Resonators, Huijing He, Jiashi Yang, Yi-Hua Huang

Department of Mechanical and Materials Engineering: Faculty Publications

We study shear-horizontal motions of a piezoelectric ceramic cylinder with an oblate elliptical cross section and axial poling. Exact thickness-shear and thickness-twist vibration modes are obtained. These modes show energy trapping, i.e., the vibration is mainly confined near the thick, central region and decays to almost nothing near the edges. The results are useful for the understanding and design of contoured piezoelectric resonators for strong energy trapping.

Sacrificial Structure Preforms For Thin Part Machining, Scott Smith, Robert Wilhelm, Brian Dutterer, Harish Cherukuri, Gaurav Goel

Department of Mechanical and Materials Engineering: Faculty Publications

Thin parts are often difficult to create by machining because they have insufficient static and dynamic stiffness. Accurate thin parts are difficult to achieve due to clamping forces, cutting forces, residual stresses, and chatter. Sacrificial structure preforms support the part during machining, but they are not part of the finished component. Preforms may be created in many ways, including forging, welding, gluing, casting, or additive processes. They can be used in many workpiece materials including metals, polymers, and ceramics. We describe a novel process that uses sacrificial structures to make machining insensitive to the thinness of finished parts.

Key Factors Influencing The Structure And Electrochemical Performances Of Lifepo4 Via Sol-Gel Synthesis, Chuang Guan

Browse all Theses and Dissertations

Olivine structured LiFePO4 is a promising cathode material for the next generation of lithium ion batteries for its low cost, environmental benign, good cycling performance and safety, etc. However, its intrinsic poor electrical conductivity and diffusion capability of lithium ion greatly hinder its application in the high power recharge battery. In this research, a cost-effective sol-gel method was used to synthesize carbon coated LiFePO4 (LiFePO4/C) materials. The influences of the synthesis parameters, including the species of iron source, lithium content, chelating agents and carbon sources, PH value of the sol, and sintering conditions etc., on the structure and electrochemical properties …

Isothermal Deformation And Modeling Of Ti-6al-4v, Vamsi Krishna Vempati

Browse all Theses and Dissertations

Ti-6Al-4V has attractive properties such as high strength to weight ratio, good fatigue properties and excellent corrosion resistance and these properties have made this alloy an important material for the aerospace industry. In this thesis, the deformation behavior of Ti-6Al-4V with several processing histories, was studied by conducting isothermal constant strain rate compression tests over a temperature range of 829°C to 996°C (1525°F to 1825°F) and at strain rates of 10-2 s-1, 10-1 s-1 and 100 s-1. True stress versus true strain flow curves showed a peak stress followed by flow softening. The data was analyzed to obtain constitutive equations …

Modeling The Exfoliation Rate Of Graphene Nanoplatelet Production And Application For Hydrogen Storage, Cory Knick

Browse all Theses and Dissertations

Graphene is a unique and revolutionary new nanomaterial. A method for it's production had a U.S. patent application in 2002 (patent issued in 2006), it was produced via mechanical exfolia-tion in 2004, and subsequently the Nobel Prize in Physics was awarded in 2010 for it. These events have sparked a surge of graphene-related research. In order for graphene to be widely studied and incorporated into emerging technologies, a versatile method for large scale produc-tion of high-quality graphene is required. Current methods are either slow or expensive which limits the scale-up of graphene production. Very recently, the liquid phase exfoliation of …

Wave Propagation And Dispersion In Microstructured Solids, Arkadi Berezovski, Juri Engelbrecht, Mihhail Berezovski

Publications

A series of numerical simulations is carried on in order to understand the accuracy of dispersive wave models for microstructured solids. The computations are performed by means of the finite-volume numerical scheme, which belongs to the class of wave-propagation algorithms. The dispersion effects are analyzed in materials with different internal structures: microstructure described by micromorphic theory, regular laminates, laminates with substructures, etc., for a large range of material parameters and wavelengths.

Coupled Electromagnetic And Heat Transfer Model For Microwave Heating In Domestic Ovens, Krishnamoorthy Pitchai, Sohan Birla, Jeyamkondan Subbiah, D. D. Jones, Harshanardhan Thippareddi

Department of Food Science and Technology: Faculty Publications

Microwave ovens are used extensively for heating a variety of not-ready-to-eat food products. Non-uniform heating of foods in microwave ovens is a major concern in assuring microbiological safety of such products. The non-uniform heating of foods is attributed by complex interaction of microwaves with foods. To understand this complex interaction, a comprehensive model was developed to solve coupled electromagnetic and heat transfer equations using finite-difference time-domain based commercial software. The simulation parameters, cell size, heating time step, and number of iterations for steady state electromagnetic field were optimized. The model was validated by 30 s heating profile of a cylindrical …

Finite Element Analysis Of The Contact Deformation Of Piezoelectric Materials, Ming Liu

Theses and Dissertations--Chemical and Materials Engineering

Piezoelectric materials in the forms of both bulk and thin-film have been widely used as actuators and sensors due to their electromechanical coupling. The characterization of piezoelectric materials plays an important role in determining device performance and reliability. Instrumented indentation is a promising method for probing mechanical as well as electrical properties of piezoelectric materials.

The use of instrumented indentation to characterize the properties of piezoelectric materials requires analytical relations. Finite element methods are used to analyze the indentation of piezoelectric materials under different mechanical and electrical boundary conditions.

For indentation of a piezoelectric half space, a three-dimensional finite element …

Microwave-Assisted Wet Chemical (Mawc) Synthesis Of Lithium Iron Phosphate, Shangzhao Shi

Dissertations, Master's Theses and Master's Reports - Open

LiFePO4 is a Co-free battery material. Its advantages of low cost, non-toxic and flat discharge plateau show promising for vehicle propulsion applications. A major problem associated with this material is its low electrical conductivity. Use of nanosized LiFePO4 coated with carbon is considered a solution because the nanosized particles have much shorter path for L+ ions to travel from the LiFePO4 crystal lattice to electrolytes. As other nano material powders, however, nano LiFePO4 could have processing and health issues.

In order to achieve high electrical conductivity while maintaining a satisfactory manufacturability, the particles should possess both of the nano- and …

Investigation Of Gallium Nitride Transistor Reliability Through Accelerated Life Testing And Modeling, Bradley D. Christiansen

Theses and Dissertations

Gallium nitride high electron mobility transistors are attractive to the DoD for their ability to operate at high frequencies, voltages, temperatures, and power. Yet, there are concerns about the reliability of these devices. Various degradation mechanisms and their causes are proposed in the literature. A variety of reliability tests were conducted to understand these mechanisms and causes. A multi-stressor experiment revealed different failure mechanisms than are in the literature. In particular, the devices tested at high voltage in the OFF state did not degrade significantly as suggested by others' reports. The validity of temperature-accelerated life testing when applied to GaN …

Generic Strategies To Implement Material Grading In Finite Element Methods For Isotropic And Anisotropic Materials, Ke Yu

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

We look at generic strategies to transfer material grading into finite element methods. Three strategies are proposed to transfer material grading into the finite element analysis. These strategies are node-centered, element-centered, and the definition of material grading through external functions. The process to achieve each strategy is stated, and examples are used to illustrate each strategy, and to compare them. The strategies are implemented in finite-deformation nonlinear elastic analysis.

Several examples are used to illustrate the implementation of each strategy for graded isotropic materials. For these examples, the results obtained from finite element models are compared with those obtained from …

Nanozeolites Doped Photopolymer Layers With Reduced Shrinkage, Mohesh Moothanchery, Izabela Naydenova, Svetlana Mintova, Vincent Toal

Articles

An acrylamide based photopolymer doped with pure silica MFI-type zeolite (silicalite-1) nanoparticles has been characterized for holographic recording purposes. The concentrations of the silicalite-1 nanoparticles in the photopolymer layers were 1, 2.5, 5 and 7.5 wt.%. The inclusion of silicalite-1 nanoparticle in the photopolymer has resulted in an increase of the diffraction efficiency by up to 40%, and decrease of the shrinkage from 1.32% to 0.57%. The best results were obtained in layers doped with 5 wt.% silicalite-1 nanoparticles.

Development Of A Structured Concrete Thermocline Thermal Energy Storage System, Bradley M. Brown

Graduate Theses and Dissertations

The past couple of decades have shown a concern when considering the way the world obtains its power. The focus has been switching from fossil fuels that have been used for hundreds of years to renewable energy sources, such as the sun. Solar energy is readily and infinitely available for harnessing. One problem with solar energy, though, is its inability to be used during the night time and during cloud covered weather. A solution to this problem is the use of energy storage mechanisms. For solar plants that use solar thermal energy (concentrating solar power plants), thermal energy storage (TES) …

Me-Em Enewsbrief, December 2011, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

The Effects Of Solvent Mixture On The Thermal And Mechanical Properties Of Solvent Cast Poly-Lactic Acid (Pla) Film, Jeremy Hughes

All Theses

CH 1 ABSTRACT
The objective of this study was to investigate the effects of various solvents on the crystallinity and thermal expansion stability of PLA film. Three different PLA films were produced by the solvent casting technique; PLA in chloroform (PLA-C), PLA in methylene chloride (PLA-M), and PLA in methylene chloride: acetonitrile = 50: 50 (PLA-MA). The PLA-MA had higher % crystallinity, 46.15, than the PLA-C, 24.03, and the PLA-M, 14.25. With this increase in crystallinity, the PLA-MA had improved thermal expansion stability as shown by very low accumulated dimensional changes at 20-100 ¡C. Wide angle x-ray diffraction identified multiple …

In-Situ Ellipsometry Characterization Of Anodically Grown Silicon Dioxide And Lithium Intercalation Into Silicon, Eric A. Montgomery

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

In this thesis, in-situ ellipsometry and electroanalytical investigations of two electrochemical processes are reported: including the formation of anodically grown silicon dioxide and the intercalation of lithium into silicon. Analysis of the ellipsometry data shows that the anodically grown silicon dioxide layer is uniform and has similar properties as thermally grown silicon dioxide. The lithium-ion intercalation data reveals non-uniform thin film formation, which requires further studies and development of appropriate ellipsometric optical models.

Advisers: Eva Schubert and Mathias Schubert

A Brief Review Of Research Progress In The Development Of Engineering Models For Lithium Ion Batteries, Da-Wei Wang, Dong-Jiang Li, Jun Li, Yong Yang

Journal of Electrochemistry

Lithium ion battery has become an important and popular electrochemical device for energy storage.Suitable evaluation and understanding of electrochemical performance and state of charge play a key role in the applications of lithium ion batteries.Construction and utilization of engineering modeling for lithium ion batteries is an effective way to fulfill this target.In this paper,engineering models of lithium ion batteries based on electrochemical reaction,ionic diffusion and migration are introduced.The emphasis is placed on the development of engineering models by the introduction of side reaction,phase transition,stress and energy.The applications of engineering models in such simulations as charge-discharge,concentration distribution,current distribution,state of charge,stress and …