Engineering Science and Materials Commons^™

Feasibility Analysis Of Estrification Systems With Entrainers, Kang Wook Lee

Dissertations and Theses

(Ethyl Acetate) and IPA (Isopropyl Acetate) production systems are studied in terms of the feasibility analysis. It is not feasible to retrieve pure products by a simple reactive distillation for IPA production system because CCR (Critical Composition Region) covers the entire desired binary edge for IPA system. On the other hand, even though CCR does not cover the entire desired binary edge of the EA system completely, internal reflux ratio (IRR) analysis does not allow the production of the pure product via reactive distillation for EA production system. To overcome the restraints, external entrainers are utilized to take advantage of …

Development Of Cost-Effective And Benign Lipid Extraction System For Microalgae, Javed Iqbal

LSU Doctoral Dissertations

A laboratory-made continuous flow lipid extraction system (CFLES) was devised to extract lipids from microalgae Nannochloropsis sp., a potential feedstock for biodiesel fuel, with a focus to assess the workable temperatures and pressures for possible scale-up applications. Using conventional solvents, the CFLES recovered 100% of the lipids recovered with conventional Soxhlet extraction (USEPA method 3540) at moderate 50 psi pressure and 100°C temperature; conditions significantly lower than those normally used in pressurized liquid extractions requiring specialized equipment. Approximately 87% of the extracted oil was successfully transesterified into biodiesel fuel. For exploring the solvent potential of biodiesel, CFLES was also tested …

A Safety Elements Model For The Building Construction Industry, Cliff Dunlap Dunlap

LSU Doctoral Dissertations

The Abstract was sent to Ms. McKenzie as an attachment to an e-mail

Heat Transfer In Microwave Heating, Zhiwei Peng

Dissertations, Master's Theses and Master's Reports - Open

Heat transfer is considered as one of the most critical issues for design and implement of large-scale microwave heating systems, in which improvement of the microwave absorption of materials and suppression of uneven temperature distribution are the two main objectives. The present work focuses on the analysis of heat transfer in microwave heating for achieving highly efficient microwave assisted steelmaking through the investigations on the following aspects: (1) characterization of microwave dissipation using the derived equations, (2) quantification of magnetic loss, (3) determination of microwave absorption properties of materials, (4) modeling of microwave propagation, (5) simulation of heat transfer, and …

Molecular Modeling Of Epon 862-Detda Polymer , Ananyo Bandyopadhyay

Dissertations, Master's Theses and Master's Reports - Open

EPON 862 is an epoxy resin which is cured with the hardening agent DETDA to form a crosslinked epoxy polymer and is used as a component in modern aircraft structures. These crosslinked polymers are often exposed to prolonged periods of temperatures below glass transition range which cause physical aging to occur. Because physical aging can compromise the performance of epoxies and their composites and because experimental techniques cannot provide all of the necessary physical insight that is needed to fully understand physical aging, efficient computational approaches to predict the effects of physical aging on thermo-mechanical properties are needed. In this …

Evaluation Of The Thermal Performance And Cost Effectiveness Of Radiant Barrier Thermal Insulation Materials In Residential Construction, Somayeh Asadi

LSU Doctoral Dissertations

Reducing heating and cooling systems loads in buildings is a cost effective way to decrease energy consumption in residential houses. This reduction can be achieved in many ways including proper insulation of the building envelope. In recent years, considerable attention was given to the use of radiant reflective insulating barriers. Over the past years, reflective barrier insulation companies nationwide have experienced significant growth resulting in an industry average growth rate of 26.8%. This significant growth is expected to continue as a result of increased cooling demands and pressure from the energy sector and the economy. Growth is also predicted to …

High Pressure Synchrotron X-Ray Diffraction Studies Of Superprotonic Transitions In Phosphate Based Solid Acids, Juan Daniel Hermosillo

Open Access Theses & Dissertations

Certain phosphate based solid acids, such as CsH2PO4 and RbH2PO4, have been shown to exhibit an abrupt, several-order-of-magnitude increase in their proton conductivity when heated above a temperature threshold. This so called superprotonic behavior allows the above-mentioned materials to function as fuel cell electrolytes at temperatures between 150C and 300C, a remarkable application that attracted significant interest especially from the automobile industry. Yet, the microscopic structures and dynamic mechanisms responsible for this behavior are not fully understood. In fact, until very recently, the very nature of the superprotonic behavior has been debate, with some groups attributing the steep proton enhancement …

Development Of Advanced Polymer Nanocomposite Capacitors, Miguel Mendoza

Open Access Theses & Dissertations

The current development of modern electronics has driven the need for new series of energy storage devices with higher energy density and faster charge/discharge rate. Batteries and capacitors are two of the most widely used energy storage devices. Compared with batteries, capacitors have higher power density and significant higher charge/discharge rate. Therefore, high energy density capacitors play a significant role in modern electronic devices, power applications, space flight technologies, hybrid electric vehicles, portable defibrillators, and pulse power applications. Dielectric film capacitors represent an exceptional alternative for developing high energy density capacitors due to their high dielectric constants, outstanding breakdown voltages, …

Hafnia-Based Nanostructured Thermal Barrier Coatings For Next Generation Gas Turbine Technology, Mohammed Noor-A-Alam

Open Access Theses & Dissertations

Extensive efforts have been directed in the last several decades towards improving thermodynamic efficiency of industrial gas turbines for power generation plants. The central theme of the efforts is to increase the turbine operating temperature and, thus, allowing higher efficiency. Thermal barrier coatings (TBC) constitute an advanced technology to protect the metallic surface from high temperature exposure for long time operation. The TBCs protect the gas turbine components from high temperature and allows further increase in engine operating temperature which subsequently increases the efficiency of the gas turbine power plant. However, the current TBC materials are capable of allowing the …

Applications Of Density Functional Theory In Materials Science And Engineering, Manuel Alvarado

Open Access Theses & Dissertations

Density Functional Theory (DFT) is a powerful tool that can be used to model various systems in materials science. Our research applies DFT to two problems of interest. First, an organic/inorganic complex dye system known as a Mayan pigment is modeled to determine chemical binding sites, verifying each model with physical data such as UV/Vis spectra. Preliminary studies on palygorskite-based mayan pigments (mayacrom blue, mayacrom purple) show excellent agreement with experimental studies when using a dimer dye geometry binding with tetrahedrally-coordinated aluminum impurity sites in palygorksite. This approach is applied to a sepiolite-based organic/inorganic dye system using thioindigo attached to …

Raman And Infrared Study Of Electrospun Plla/Pcl Nanofiber Blends For Use In Tissue Engineering, Jose Luis Enriquez Carrejo

Open Access Theses & Dissertations

Recently, the biomedical engineering field has developed at a very fast pace as improved techniques and materials become available to promote its growth. Consequently, the research in polymeric biomaterials has been highly stimulated by this trend. The goal of the current research is to demonstrate the usefulness of the Raman scattering, Raman mapping, and infrared absorption spectroscopies to tissue engineering, by spectroscopically characterizing blends of PLLA and PCL polymers, which were prepared by electrospinning with and without cell addition. The proposed use of these blends is as primary biomaterials in biodegradable scaffolds used in tissue engineering. Both Raman and infrared …

Development Of A Multi-Material, Multi-Technology Fdm System For Process Improvement Experimentation, David Espalin

Open Access Theses & Dissertations

Over the last three decades, developments within the area of Additive Manufacturing (AM) have resulted in novel technologies capable of producing highly customized, complex part geometries in a fraction of the lead time required by traditional manufacturing methods (e.g., injection molding, metal casting). In particular, fused deposition modeling (FDM), a material extrusion AM process, can produce parts using production-grade thermoplastics like acrylonitrile butadiene styrene, polycarbonate, and polyetherimide. Additionally, non-commercial materials (e.g., polycaprolactone, ceramic loaded polymers, carbon nanotube loaded polymers) have been processed using FDM in part to demonstrate the potential diversity in material selection.

Recently, a myriad of personal 3D …

The Effect Of Al And B Additions On The Oxidation Behavior Of Alloys From The Nb-Cr-Si System, Nydia Judit Esparza

Open Access Theses & Dissertations

Nickel based superalloys have been developed to perform substantially in industry however as technology develops, the need and desire to increase service temperatures to improve efficiency and performance is pushing the capabilities of these alloys. These aspired requirements entail the research and development of new structural materials that surpass the abilities of nickel alloys. Research in Nb-based alloys is underway as Nb alloys have shown to be a promising alternative with similar density but higher melting temperatures than the Ni alloys. However, because Nb has poor oxidation properties extensive studies are necessary to develop an alloy that can perform as …

A Study Of Wo3 And W0.95ti0.05o3 Thin Films Using Comparative Spectroscopy, James Heyward Howard

Open Access Theses & Dissertations

Tungsten oxide (WO3) is important and well-studied in materials science, particularly for sensor applications. In this research work, we consider the innovation of adding Ti to thin films of this material. Since the characteristics of any such material are strongly dependent on the conditions and methods used in its deposition, the main objective of this project is to provide a detailed spectroscopic characterization by Raman scattering, infrared absorption, and X-ray photoelectron spectroscopy (XPS) of WO3 and of W0.95Ti0.05O3. This characterization will be based on comparison of the morphology and composition of WO3-based thin films, grown by radio frequency magnetron reactive …

Development Of Nanocomposites For Energy Storage Devices, Md Ashiqur Rahaman Khan

Open Access Theses & Dissertations

With the ever-increasing need in improving the performance and operation life of future mobile devices, developing higher power density energy storage devices has been receiving more attention. Lithium ion battery (LIB) and capacitor are two of the most widely used energy storage devices and have attracted increasing interest from both industrial and academic fields. Batteries have higher power density than capacitor but significantly longer charge/discharge rates. In order to further improve the performance of these energy storage devices, one of the approaches is to use high specific surface area nano-materials. Among all the nano-materials developed so far, one-dimensional nanowires are …

Nanoprobe I-V Characterization Of Cdte/Cds Micro And Nano-Patterned Solar Cells, Heber Prieto

Open Access Theses & Dissertations

This thesis presents a novel way to characterize micro and nano patterned cadmium telluride thin film solar cells via a nano-probe system. A historical review of CdTe-based solar cells is presented first followed by review of the technology developed to produce the patterned CdTe cells. A detailed presentation is then provided on the use of a Zyvex nanoprobing system to characterize the patterned solar cells. The I-V response of micro- and nano-patterned solar cells stimulated under different e-beam conditions is presented and analyzed. Suggestions of how to improve the technique are provided. This work documents, for the first time, the …

The Influence Of Build Parameters On The Microstructure During Electron Beam Melting Of Ti6al4v, Karina Puebla

Open Access Theses & Dissertations

With the demand of devices to replace or improve areas, such as: electronic, biomedical and aerospace industries. Improvements in these areas of engineering have been in need due to the customer’s needs for product properties requirements. The design of components must exhibit better material properties (mechanical or biocompatible) close to those of any given product. Rapid prototyping (RP) technologies that were originally designed to build prototypes may now be required to build functional end-use products. To carry out the transition, from RP to rapid manufacturing (RM), the available materials utilized in RP must provide the performance required for RM. The …

Oxidation Of Borides And Carbides With Y2o3 And Ta Additions, Salvador Manuel Rodriguez

Open Access Theses & Dissertations

The study presented here describes an investigation of an oxidation scale of a fully-sintered Y2O3-ZrB2-TiC composite exposed in air at 1173K. Upon oxidation of the boride/carbide, a ZrO2-TiO2 was expected to form similar to the ZrO2-SiO2 dual scale of an oxidized ZrB2-SiC. The 47wt% Y2O3-38wt%ZrB2-16wt%TiC composite formed a dual scale consisting primarily of an Y2O3-ZrO2-TiC inner scale with an outer scale of ZrO2-TiO2-Y2O3.

The samples oxidized with a parabolic layer growth allowing the calculation of the effective diffusion coefficient indicating that the oxidation was controlled by oxygen ingress through primarily the ZrO2-Y2O3 phase. The oxygen potential between the inner layer …

Optical Detection Of Melting Point Depression For Silver Nanoparticles Via In Situ Real Time Spectroscopic Ellipsometry, S. A. Little, T. Begou, R. W. Collins, S. Marsillac

Electrical & Computer Engineering Faculty Publications

Silver nanoparticle films were deposited by sputtering at room temperature and were annealed while monitoring by real time spectroscopic ellipsometry (SE). The nanoparticle dielectric functions (0.75 eV-6.5 eV) obtained by SE were modeled using Lorentz and generalized oscillators for the nanoparticle plasmon polariton (NPP) and interband transitions, respectively. The nanoparticle melting point could be identified from variations in the oscillator parameters during annealing, and this identification was further confirmed after cooling through significant, irreversible changes in these parameters relative to the as-deposited film. The variation in melting point with physical thickness, and thus average nanoparticle diameter, as measured by SE …

Improving Discourse Structure Identification, Jamie Allison Guidry

LSU Master's Theses

Rhetorical Structure Theory (Mann et al. 1988), a popular approach for analyzing discourse coherence, suggests that coherent text can be placed into a hierarchical organization of clauses. Identification of a text’s rhetorical structure through automatic discourse analysis is a crucial element for many of today’s Natural Language Processing tasks, but no sufficient tool is available. The current state-of -the-art discourse parser, SPADE (Soricut et al. 2003), is limited to parsing discourse within a single sentence. HILDA (Hernault et al. 2010) extends the parsing abilities of SPADE to the document level, but with a decrease in performance. This study achieved document-level …