Engineering Science and Materials Commons^™

Generalized Ellipsometry In-Situ Quantification Of Organic Adsorbate Attachment Within Slanted Columnar Thin Films, Keith B. Rodenhausen Jr., Daniel Schmidt, Tadas Kasputis, Angela K. Pannier, Eva Schubert, Mathias Schubert

Department of Chemical and Biomolecular Engineering: Faculty Publications

We apply generalized ellipsometry, well-known to be sensitive to the optical properties of anisotropic materials, to determine the amount of fibronectin protein that adsorbs onto a Ti slanted columnar thin film from solution. We find that the anisotropic optical properties of the thin film change upon organic adsorption. An optical model for ellipsometry data analysis incorporates an anisotropic Bruggeman effective medium approximation. We find that differences in experimental data from before and after fibronectin adsorption can be solely attributable to the uptake of fibronectin within the slanted columnar thin film. Simultaneous, in-situ generalized ellipsometry and quartz crystal microbalance measurements show …

Effects Of Mismatched Electrodes On An At-Cut Quartz Resonator, Huijing He, Jinxi Liu, Jiashi Yang

Department of Mechanical and Materials Engineering: Faculty Publications

We study thickness-shear and thickness-twist free vibrations of a finite AT-cut quartz resonator with mismatched electrodes. The equations of anisotropic elasticity are used with the omission of the small elastic constant c56. An analytical solution is obtained using Fourier series from which the resonant frequencies, mode shapes, and vibration confinement resulting from the electrode inertia are calculated and examined.

On The Stability Of A Microstructure Model, Mihhail Berezovski, Arkadi Berezovski

Publications

Abstract

The asymptotic stability of solutions of the Mindlin-type microstructure model for solids is analyzed in the paper. It is shown that short waves are asymptotically stable even in the case of a weakly non-convex free energy dependence on microdeformation.

Research highlights

The Mindlin-type microstructure model cannot describe properly short wave propagation in laminates. A modified Mindlin-type microstructure model with weakly non-convex free energy resolves this discrepancy. It is shown that the improved model with weakly non-convex free energy is asymptotically stable for short waves.

Effect Of External Electric Field On Hydrogen Adsorption Over Activated Carbon Separated By Dielectric Materials, Zheng Zhang

Dissertations, Master's Theses and Master's Reports - Open

Energy crisis and worldwide environmental problem make hydrogen a prospective energy carrier. However, storage and transportation of hydrogen in large quantities at small volume is currently not practical. Lots of materials and devices have been developed for storage hydrogen, but to today none is able to meet the DOE targets.

Activated carbon has been found to be a good hydrogen adsorbent due to its high surface area. However, the weak van der Waals force between hydrogen and the adsorbent has limited the adsorption capacity. Previous studies have found that enhanced adsorption can be obtained with applied electric field. Stronger interaction …

Environmental Value Engineering (Eve) Comparison Of A Usgbc Leadership In Energy And Environmental Design (Leed) Window System And Non-Leed Window System, Simon A. Adamtey

Master of Technology Management Plan II Graduate Projects

ABSTRACT

The need to explore environmentally friendly materials to avoid the depletion of the nonrenewable resources is very significant. The human race has been heavily dependent on nonrenewable resources since the industrial revolution. The rate of consumption of these resources is higher than the rate at which these resources replenish themselves since it has been established that most of these resources take millions of years to replenish. A critical look into the future reveals that there is a looming resource crisis since these resources are being depleted.

Fossil fuel combustion is linked to the increase in CO₂ in the …

Systems And Synthetic Biology Of The Vessel Wall, Jennifer Frueh, Nataly Maimari, Ying Lui, Zoltan Kis, Vikram Mehta, Negin Pormehr, Calum Grant, Emmanuel Chalkias, Mika Falck-Hansen, Sandra Bovens, Ryan M. Pedrigi, Taka Homma, Gianfillippo Coppola, Rob Krams

Department of Mechanical and Materials Engineering: Faculty Publications

Atherosclerosis is intimately coupled to blood flow by the presence of predilection sites. The coupling is through mechanotransduction of endothelial cells and approximately 2000 gene are associated with this process. This paper describes a new platform to study and identify new signalling pathways in endothelial cells covering an atherosclerotic plaque. The identified networks are synthesized in primary cells to study their reaction to flow. This synthetic approach might lead to new insights and drug targets.

Tool Sequence Trends In Minimally Invasive Surgery: Statistical Analysis And Implications For Predictive Control Of Multifunction Instruments, Carl A. Nelson, Evan Luxon, Dmitry Oleynikov

Department of Mechanical and Materials Engineering: Faculty Publications

This paper presents an analysis of 67 minimally invasive surgical procedures covering 11 different procedure types to determine patterns of tool use. A new graph-theoretic approach was taken to organize and analyze the data. Through grouping surgeries by type, trends of common tool changes were identified. Using the concept of signal/noise ratio, these trends were found to be statistically strong. The tool-use trends were used to generate tool placement patterns for modular (multi-tool, cartridge-type) surgical tool systems, and the same 67 surgeries were numerically simulated to determine the optimality of these tool arrangements. The results indicate that aggregated tool-use data …

Method For Increasing The Efficiency Of Organic Photovoltaic Cells, Jinsong Huang, Yongbo Yuan

Department of Mechanical and Materials Engineering: Faculty Publications

The present invention is directed to an organic photovoltaic cell that contains one or more dipole regions generally disposed between an organic active region and the electrodes and a process for producing such an organic photovoltaic cell.

Effect Of Surface Roughness On Slip Flow In Nanoscale Polymer Films, Anoosheh Niavarani, Nikolai Priezjev

Mechanical and Materials Engineering Faculty Publications

No abstract provided.

Monitoring The Wall Mechanics During Stent Deployment In A Vessel, Brian Steinert, Shijia Zhao, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

Clinical trials have reported different restenosis rates for various stent designs . It is speculated that stentinduced strain concentrations on the arterial wall lead to tissue injury, which initiates restenosis . This hypothesis needs further investigations including better quantifications of non-uniform strain distribution on the artery following stent implantation. A non-contact surface strain measurement method for the stented artery is presented in this work. ARAMIS stereo optical surface strain measurement system uses two optical high speed cameras to capture the motion of each reference point, and resolve three dimensional strains over the deforming surface. As a mesh stent is deployed …

Macro And Microfluidic Flows For Skeletal Regenerative Medicine, Brandon D. Riehl, Jung Yul Lim

Department of Mechanical and Materials Engineering: Faculty Publications

Fluid flow has a great potential as a cell stimulatory tool for skeletal regenerative medicine, because fluid flow-induced bone cell mechanotransduction in vivo plays a critical role in maintaining healthy bone homeostasis. Applications of fluid flow for skeletal regenerative medicine are reviewed at macro and microscale. Macroflow in two dimensions (2D), in which flow velocity varies along the normal direction to the flow, has explored molecular mechanisms of bone forming cell mechanotransduction responsible for flow-regulated differentiation, mineralized matrix deposition, and stem cell osteogenesis. Though 2D flow set-ups are useful for mechanistic studies due to easiness in in situ and post-flow …

Nanotopographic Cell Culture Substrate: Polymer-Demixed Nanotextured Films Under Cell Culture Conditions, Jung Yul Lim, Christopher A. Siedlecki, Henry J. Donahue

Department of Mechanical and Materials Engineering: Faculty Publications

Modulating physical cell culture environments via nanoscale substrate topographic modification has recently been of significant interest in regenerative medicine. Many studies have utilized a polymer-demixing technique to produce nanotextured films and showed that cellular adhesion, proliferation, and differentiation could be regulated by the shape and scale of the polymer-demixed nanotopographies. However, little attention has been paid to the topographic fidelity of the polymer-demixed films when exposed to cell culture conditions. In this brief article, two polymer-demixing systems were employed to assess topographic changes in polymer-demixed films after fibronectin (FN) extracellular matrix protein adsorption and after incubation in phosphate-buffered saline at …

Usability Assessment Of Two Different Control Modes For The Master Console Of A Laparoscopic Surgical Robot, Xiaoli Zhang, Carl A. Nelson, Dmitry Oleynikov

Department of Mechanical and Materials Engineering: Faculty Publications

The objective of this study is to evaluate potential interface control modes for a compact fourdegree- of-freedom (4-DOF) surgical robot. The goal is to improve robot usability by incorporating a sophisticated haptics-capable interface. Two control modes were developed using a commercially available haptic joystick: (1) a virtually point-constrained interface providing an analog for constrained laparoscopic motion (3-DOF rotation and 1-DOF translation), and (2) an unconstrained Cartesian input interface mapping more directly to the surgical tool tip motions. Subjects (n = 5) successfully performed tissue identification and manipulation tasks in an animal model in point-constrained and unconstrained control modes, respectively, with …

Moisture Damage Characterization Of Warm-Mix Asphalt Mixtures Based On Laboratory-Field Evaluation, Yong-Rak Kim, Jun Zhang, Hoki Ban

Department of Mechanical and Materials Engineering: Faculty Publications

This study presents laboratory evaluation integrated with field performance to examine two widely used warm-mix asphalt (WMA) approaches—foaming and emulsion technology. For a more realistic evaluation of the WMA approaches, trial pavement sections of the WMA mixtures and their counterpart hot-mix asphalt (HMA) mixtures were implemented in Antelope County, Nebraska. Field-mixed loose mixtures collected at the time of paving were transported to the laboratories to conduct various experimental evaluations of the individual mixtures. Among the laboratory tests, three (two conventional and one newly attempted) were performed to characterize moisture damage potential which is the primary focus of this study. From …

Thin Film Growths Of Znte And Cdte On Various Substrates Using A Novel Close Space Sublimation Reactor Css4, Damian Marrufo

Open Access Theses & Dissertations

Thin films of CdTe have been grown on CdS in a variety of methods for use in thin film photovoltaic systems. Limits to the efficiency of CdTe/CdS solar cells have been attributed to defects in the lattice that occur between the interface of CdS and CdTe due to a lattice mismatch. A close space sublimation (CSS) reactor known as the CSS4 was designed and fabricated in UTEP to deposit complex layers of CdTe and ZnTe on top of a CdS film that is grown via chemical bath deposition in order to obtain a CdTe photovoltaic. Unfortunately, the original design and …

A Novel Method For The Curing Of Metal Particle Loaded Conductive Inks And Pastes, David Adrian Roberson

Open Access Theses & Dissertations

The emerging technology of printed microelectronics involving the use of conductive inks in conjunction with standard printing techniques offers a fast and low waste method for creating microelectronics compared with standard manufacturing processes. A clear path to the creation of flexible electronics is present due to the ease of printing on flexible substrates. Moreover, creation of novel 3D structural electronics is possible via the integration of printing technologies and additive manufacturing (AM) techniques.

A key obstacle to the manufacturing of flexible and structural electronics comes from the temperature restrictions imposed by the substrates, which are typically polymeric. This hindrance has …

Structure Morphology And Optical Properties Of Nanocrystalline Ga2o3 Thin Films, Sampath Kumar Samala

Open Access Theses & Dissertations

Gallium Oxide thin films were produced by sputter deposition by varying the substrate temperature (T_s) in a wide range (T_s=25-800 oC) and under variable deposition time. The structural characteristics and optical properties of Ga₂O₃ films were evaluated using X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray spectrometry (EDS), Rutherford backscattering spectrometry (RBS) and spectrophotometric measurements. The effect of growth temperature is significant on the chemistry, crystal structure and morphology of Ga₂O₃ films. XRD and SEM analyses indicate that the Ga₂O₃ films grown at lower temperatures were …

A Front Tracking Model Of The Maxus-8 Microgravity Solidification Experiment On A Ti-45.5at.% Al-8at.%Nb Alloy, Robin Mooney, Shaun Mcfadden, Marek Rebow, David J. Browne

Articles

On 26th March 2010 the MAXUS-8 sounding rocket was launched from the Esrange Space Center in Sweden. As part of the Intermetallic Materials Processing in Relation to Earth and Space Solidification (IMPRESS) project, a solidification experiment was conducted on a Ti-45.5at.%Al-8at.%Nb intermetallic alloy in a module on this rocket. The experiment was designed to investigate columnar and equiaxed microstructures in the alloy. A furnace model of the MAXUS 8 experiment with a Front Tracking Model of solidification has been developed to determine the macrostructure and thermal history of the samples in the experiment. This paper gives details of results of …

The Effect Of Al, Mo, And B On The Oxidation Behavior Of Three Nb-Based Alloys, Victoria Rae Rangel

Open Access Theses & Dissertations

Extensive work has been undertaken to develop niobium based structural alloys for high temperature applications. These developments have led to the increase in engine operating temperatures and better performance efficiency. New materials including alloys based on metals with higher melting points such as molybdenum and niobium with silicon are now being examined as a better alternative to nickel base superalloys. Materials with a niobium silicide based composites have the potential for higher temperature capabilities. The oxidation behavior of Nb-20Cr-10Si and Nb-20Cr-10Si-5Al has been studied in a range of temperature from 700 to 1400°C in static air. Isothermal oxidation experiments indicate …

The Effects Of Uncommon Silicides On The Oxidation Of Alloys From The Nb-Cr-Si System, Daniel Brendan Voglewede

Open Access Theses & Dissertations

Niobium based alloys are being tapped as potential successors to current nickel base superalloys in high temperature applications. In the aerospace industry, high temperature materials are constantly being pushed to higher temperature regimes in order to improve engine efficiency however current superalloys cannot be pushed further due to melting temperature limitations. Niobium, being a refractory metal, can withstand much higher temperatures than nickel however its oxidation properties are woefully inadequate.

The purpose of this study is to ascertain whether increased silicon additions can improve niobium oxidation properties by: forming ternary silicides with better oxidation properties and by preventing the formation …