Performance Analysis Of A Variable Conductance Heat Pipe, Herron Arreola

Aerospace Engineering

This report examines the analysis of a donated Boeing variable conductance heat pipe with unknown performance characteristics. These characteristics were found through experimental means by utilizing 14 thermocouples attached to various locations on the heat pipe, the heaters and to the insulation. Although the maximum axial heat transport capability could not be determined due to the limited number of strip heaters available, the maximum radial heat flux capability of the heat pipe was found to be 2.46 W/in². The experiment also revealed that increasing the input power decreased the burn out inclination angle and that using a coolant …

Mars Carbon Dioxide Propulsion, Christopher Cushman Perry

Mechanical & Aerospace Engineering Theses & Dissertations

An experimental investigation was conducted to characterize the performance of a small-scale supersonic propulsion system using supercritical CO₂ as a propellant intended for Mars surface applications. This research has focused on estimating the specific impulse behavior of high-pressure carbon dioxide propellant that can be produced by condensing dry ice out of Mars's atmosphere and heating it at constant volume to temperatures above its 31.1 ° C critical temperature. Since supercritical fluid was created by heating different dry ice-vapor mixtures to moderate temperatures, the nominal initial density and thermodynamic state within the pressure vessel could be controlled. The instrumented test …

Radiation Effects Basics For 7750, Robert J. Twiggs

Robert "Bob" Twiggs STEM Education Collection

A PowerPoint presentation created by Professor Bob Twiggs on "Radiation Effects Basics for 7750" on September 25, 2011.

Space Environment-Iii Lecture - Powerpoint Presentation, Robert J. Twiggs

Robert "Bob" Twiggs STEM Education Collection

Professor Bob Twiggs' lecture on Space Environment-III PowerPoint presentation delivered on September 2, 2011.

Space Environment - A Review, Robert J. Twiggs

Robert "Bob" Twiggs STEM Education Collection

A PowerPoint presentation created by Professor Bob Twiggs on "Space Environment" on September 2, 2011.

Designing Propulsion Systems For Future Aerospace Applications, Nihad E. Daidzic

Aviation Department Publications

No abstract provided.

A Taskable Space Vehicle: Realizing Cost Savings By Combining Orbital And Suborbital Flight, Thomas Co, Jonathan T. Black

Faculty Publications

The use of space gives the United States distinct advantages in any battlefield environment, but the high cost of space operations increasingly jeopardizes those advantages. Although the United States pioneered much of the current space technology, declining budgets for space research, development, and operations leave our legacy systems vulnerable to adversaries around the world. Other nations formerly incapable of space exploitation are quickly learning to counter US space technologies at surprisingly low costs. In order to reduce the expense of deploying and maintaining a robust space capability, the Department of Defense (DOD) must change the status quo in space operations …

Thermal Analysis Of The Cubesat Cp3 Satellite, Jonas Friedel, Sean Mckibbon

Aerospace Engineering

Due to inconsistencies found in the on-orbit thermal data from the CubeSat CP3 satellite between 2007 and 2011, further analysis is performed on a larger number of data from August 2010 through April 2011, aiming to find an explanation for the overall increasing measured temperatures and shortening peak periods. Therefore, the satellite power data as well as orbital anomalies are analyzed leading to the conclusion that the satellite was temporarily (January – March 2011) orbiting with significantly increased sun exposure causing the higher temperatures. The shortened temperature peak periods are explained by alternating albedo values as the main influence in …

Design, Manufacturing And Testing Of An Environmentally-Green Bipropellant Thruster, Alex Bendoyro, Gabriel Sanchez, Erin Stearns, Phillip Takahashi

Aerospace Engineering

This project reviews the design, manufacturing and experimentation process of a green bi-propellant thruster designed to output 5 lbf. The goals were to successfully design, manufacture and test a thruster, while discovering the complications that arise through out the complete design process of a green thruster. The thruster was successfully designed using ideal rocket equations and the design was successfully confirmed using CFD and FEA. Manufacturing of the thruster was fully planned and revealed mild flaws in thruster design. For example some features were not manufacturable to the exact measurements desired. Testing of the engine gave results inconsistent with expected …

Numerical Modeling Of The Cn Spectral Emission Of The Stardust Re-Entry Vehicle, Alexandre Martin, Erin D. Farbar, Iain D. Boyd

Mechanical Engineering Faculty Publications

Re-entry vehicles designed for space exploration are usually equipped with thermal protection systems made of ablative material. In order to properly model and predict the aerothermal environment of the vehicle, it is imperative to account for the gases produced by ablation processes. In the case of charring ablators, where an inner resin is pyrolyzed at a relatively low temperature, the composition of the gas expelled into the boundary layer is complex and may lead to thermal chemical reactions that cannot be captured with simple ow chemistry models. In order to obtain better predictions, an appropriate gas ow chemistry model needs …

Design, Fabrication, And Testing Of An Electromagnetic Rail Gun For The Repeated Testing And Simulation Of Orbital Debris Impacts, Jeff Maniglia, Jordan Smiroldo, Alex Westfall, Guy Zohar

Aerospace Engineering

An Electromagnetic Railgun (EMRG) was designed, built, and tested, capable of firing a projectile a 1 gram projectile at 650 m/s muzzle velocity. The EMRG utilizes an injector, a high voltage power supply, a capacitor bank, inductors and rails. The injector fires 2300 psig Nitrogen gas into the system to provide an initial velocity. The high voltage power supply charges the capacitor bank. The capacitor bank discharges the electric potential built up through the projectile while inside the rails in order to create the EMRG’s force. The inductors are used to pulse form the capacitor bank in order to get …

An Analysis Of Stabilizing 3u Cubesats Using Gravity Gradient Techniques And A Low Power Reaction Wheel, Erich Bender

Aerospace Engineering

The purpose of this paper is to determine the feasibility of gravity gradient stabilizing a 3U CubeSat and then using a miniature reaction wheel to further increase stability characteristics. This paper also serves as a guide to understanding and utilizing quaternions in attitude control analysis. The analytical results show that using 33 centimeter booms and 400 gram tip masses, a 3U CubeSat will experience a maximum of 6 degrees of angular displacement in yaw and pitch, and less than .5 degrees of angular displacement in the nadir axis. A .120 kilogram miniature reaction wheel developed by Sinclair Interplanetary was introduced …

Development Of A Cubesat Instrument For Microgravity Particle Damper Performance Analysis, John Trevor Abel

Master's Theses

Spacecraft pointing accuracy and structural longevity requirements often necessitate auxiliary vibration dissipation mechanisms.  However, temperature sensitivity and material degradation limit the effectiveness of traditional damping techniques in space.  Robust particle damping technology offers a potential solution, driving the need for microgravity characterization.   A 1U cubesat satellite presents a low cost, low risk platform for the acquisition of data needed for this evaluation, but severely restricts available mass, volume, power and bandwidth resources.  This paper details the development of an instrument subject to these constraints that is capable of capturing high resolution frequency response measurements of highly nonlinear particle damper dynamics.

Review Of The Maxus 8 Sounding Rocket Experiment To Investigate Solidification In A Ti-Al-Nb Alloy, Robin Mooney, David Browne, Olga Budenkova, Yves R. Fautrelle, Ludo Froyen, Andrey Kartavykh, Stephan Rex, Burkhard Schmitz, Daniella Voss, Shaun Mcfadden

Conference Papers

A review of the MAXUS 8 sounding rocket microgravity experiment to investigate solidification structures in a Ti-Al-Nb intermetallic alloy is presented. The experiment was part of the Intermetallic Materials Processing in Relation to Earth and Space Solidification (IMPRESS) EU FP6 project. Key objectives were to investigate columnar and equiaxed solidification, and to achieve Columnar-to-Equiaxed Transition (CET) in the alloy. A microgravity experiment was designed to achieve this using a controlled power-down method. Two alloys were tested: one inoculated with a grain refiner and the other without grain refinement. Unrefined samples displayed axial and radial columnar growth. Boride inoculated samples displayed …

Development Of A Laboratory Experiment To Simulate Upper-Stage Rocket Explosions, Timothy J. Price

Aerospace Engineering

This report is a summary of the senior project entitled Development of a Laboratory Experiment to Simulate Upper-Stage Rocket Explosions. The goal of the experiment was to recreate a NASA experiment which used aluminum soft drink cans to approximate the shape of an Ariane third stage rocket. The cans were placed in a vacuum chamber and fired upon with a projectile from a light gas gun. The resulting debris was collected and analyzed allowing several conclusions to be made regarding the behavior or rocket breakups and the formation of space debris. In lieu of a light gas gun, energy drink …

Preliminary Design Of An Asteroid Hopping Mission, Michael D. Scheppa

Doctoral Dissertations and Master's Theses

In 2010, NASA announced that its new vision is to support private space launch operations. It is anticipated that this new direction will create the need for new and innovative ideas that push the current boundaries of space exploration and contain the promise of substantial gain, both in research and capital.

The purpose of the study is to plan and estimate the feasibility of a mission to visit a number of near Earth asteroids (NEAs). The mission would take place before the end of the 21st century, and would only use commercially available technology. Throughout the mission design process, while …

Using A Gatling-Gun Configured Micro Pulsed Plasma Thruster As A Means To Control Micro Satellites With Extreme Precision, Lee I. Watson

Theses and Dissertations

Micro-Pulsed Plasma Thrusters (µPPT) are becoming increasingly attractive for their low power consumption and moderately high specific impulse in the range of 800-1200s. The Gatling Gun micro-Pulsed Plasma Thruster (GG-µPPT) is a new device offering reduced mass and higher thrust than single µPPTs and solid application in precise pointing and orbit maintenance applications. The performance of µPPTs depends on frequency and applied voltage/power levels. Variation of these input parameters and effects on operation and performance of this thruster system were the focus of this research. Contamination aspects were also considered and discussed, since the buildup of carbon results in decreased …

Starting Cansat – Where To Now?, Robert J. Twiggs

Robert "Bob" Twiggs STEM Education Collection

A PowerPoint presentation created by Professor Bob Twiggs titled "Starting CanSat – Where to Now?" from March 8, 2011.

The Future Of Cubesats: Presentation To The Iaa, Ben Malphrus

Robert "Bob" Twiggs STEM Education Collection

A PowerPoint presentation created by Professor Bob Twiggs titled "The Future of CubeSats: Presentation to the IAA" from January 28, 2011.

Optimal Attitude Control Management For A Cubesat, Michael James Develle

Electronic Theses and Dissertations

CubeSats have become popular among universities, research organizations, and government agencies due to their low cost, small size, and light weight. Their standardized configurations further reduce the development time and ensure more frequent launch opportunities. Early cubesat missions focused on hardware validation and simple communication missions, with little requirement for pointing accuracy. Most of these used magnetic torque rods or coils for attitude stabilization. However, the intrinsic problems associated with magnetic torque systems, such as the lack of three-axis control and low pointing accuracy, make them unsuitable for more advanced missions such as detailed imaging and on-orbit inspection. Threeaxis control …