Consideration Of Wear Rates At High Velocities,
2010
Air Force Institute of Technology
Consideration Of Wear Rates At High Velocities, Stephen P. Meador
Theses and Dissertations
The goal of this research is to study sliding contact wear of test sled slippers at high velocities. Experimentation representative of the slippers is infeasible, so numerical studies are used. An Eulerian-Lagrangian hydrocode called CTH is used to study mechanical wear. Failure criteria have been established to evaluate the stresses and strains resulting from the hydrocode simulation of a single asperity collision. The results from the hydrocode simulations are scaled to account for slipper bounce and multiple asperities, and these results produce total wear values that are approximately 90% of total experimental wear. Slipper thermodynamics have also been evaluated. The …
Disturbance Observer: Design And Flight Test Of A Large Envelope Flight Controller,
2010
Air Force Institute of Technology
Disturbance Observer: Design And Flight Test Of A Large Envelope Flight Controller, Donevan A. Rein
Theses and Dissertations
A new flight controller was evaluated through piloted simulation and flight test conducted at the USAF Test Pilot School. The controller, commonly called a disturbance observer, uses inertial sensor feedback routed through a simple control architecture that acts to force the desired response while rejecting sensor noise and atmospheric disturbances. The investigation included both handling qualities testing in the Octonian simulator at the Air Force Research Laboratories Air Vehicle Directorate, and initial flight test conducted as part of a Test Management Project at the USAF TPS. Simulation produced positive results with desired performance throughout a wide flight envelope. In addition, …
Conceptual Design Tool For Fuel-Cell Powered Micro Air Vehicles,
2010
Air Force Institute of Technology
Conceptual Design Tool For Fuel-Cell Powered Micro Air Vehicles, Paul M. Hrad
Theses and Dissertations
A conceptual design tool was built to explore power requirements of a hybrid-power system for Micro Air Vehicles (MAVs) comparable in size to the Cooper's Hawk. An inviscid aerodynamic code, Athena Vortex Lattice (AVL), and a motor-propeller analysis code, QPROP, provide overall lift, drag, and thrust data for power-required calculation as functions of many variables to include mass, platform geometry, altitude, velocity, and mission duration. Phoenix Technologies’ Model Center was used to integrate multi-disciplinary components that employ specific power and specific energy of two power sources to determine power system mass required for a designated mission. The tool simulated a …
Structural Response Of Slotted Waveguide Antenna Stiffened Structure Components Under Compression,
2010
Air Force Institute of Technology
Structural Response Of Slotted Waveguide Antenna Stiffened Structure Components Under Compression, Joseph W. Sabat Jr.
Theses and Dissertations
The Slotted Waveguide Antenna Stiffened Structure (SWASS) is an aircraft system that can provide the capabilities of a stiffened panel skin structure and a slotted waveguide radar antenna simultaneously. The system made from carbon fiber reinforced polymers is designed around a 10 GHz radar frequency in the X-band range and uses a WR-90 waveguide as a baseline for design. The system is designed for integration into fuselage or wing sections of intelligence, surveillance, and reconnaissance (ISR) aircraft and would increase the system performance through the availability of increased area and decreased system weight. Elemental parts of the SWASS structure were …
Design Of A Film Cooling Experiment For Rocket Engines,
2010
Air Force Institute of Technology
Design Of A Film Cooling Experiment For Rocket Engines, Andrew L. Sincock
Theses and Dissertations
The Film Cooling Rig (FCR) is a new test rig at the Air Force Institute of Technology (AFIT) to study film cooling for rocket engine applications. The original researcher designed, built, and then utilized the FCR to study radial curvature effects on film cooling for a non-combustion environment. This effort modified the FCR by adding propane-air combustion. Modular stainless steel test sections were produced to allow study of various curvatures and coolant injection angles. A pre-mixed burner was designed and built to deliver main flow mass flow rates necessary to produce blowing ratios as low as 0.5. A water cooling …
Exfit Flight Design And Structural Modeling For Falconlaunch Viii Sounding Rocket,
2010
Air Force Institute of Technology
Exfit Flight Design And Structural Modeling For Falconlaunch Viii Sounding Rocket, Michael J. Vinacco
Theses and Dissertations
This research effort furthers the Air Force’s study of reusable launch vehicles and hypersonic airfoils by conducting a hypersonic flight test using the US Air Force Academy’s FalconLAUNCH VIII sounding rocket. In this study, two experimental fin tips were designed and attached to the sounding rocket in place of two stabilizer fins in order to collect data throughout the rocket’s hypersonic flight profile. The desire to research, study, and test experimental fin tips was driven by the Air Force Research Laboratory’s Future responsive Access to Space Technologies (FAST) program and their desire to include vertical stabilizers on the wing tips …
Design Analysis Of A Sapce Based Chromotomographic Hyperspectral Imaging Experiment,
2010
Air Force Institute of Technology
Design Analysis Of A Sapce Based Chromotomographic Hyperspectral Imaging Experiment, Todd A. Book
Theses and Dissertations
This research develops the design of several components and/or systems for an experimental space-based chromotomographic hyperspectral imager that is being built by the Air Force Institute of Technology. The design work includes three separate topics. The first topic was the development of a structure utilizing finite element analysis and eigenanalysis for the ground-based version of the chromotomographic experiment (CTEx). The ground-based experiment was performed as a risk mitigation measure for the space-based experiment. The second topic includes a design review of a contractor's proposed off-axis Mersenne telescope for the space-based chromotomographic hyperspectral imager. The work included the creation of preliminary …
Attitude Control Of A Satellite Simulator Using Reaction Wheels And A Pid Controller,
2010
Air Force Institute of Technology
Attitude Control Of A Satellite Simulator Using Reaction Wheels And A Pid Controller, Ryan E. Snider
Theses and Dissertations
Attitude requirements of a satellite are determined by its mission: telecommunications, optical imagery, and meteorology to name a few. A satellite's ability to orient its mission critical hardware (solar arrays, attitude sensors, etc.), as well as its mission specific payload, is incumbent upon the performance of the satellite's attitude control system (ACS). For a highly accurate ACS and for moderately fast maneuverability, reaction wheels are preferred because they allow continuous and smooth control while inducing the smallest possible disturbance torques. The objective of this research is to design, build, test, and evaluate the performance of a reaction wheel ACS on-board …
Relative Orbit Elements For Satellites In Elliptical Orbits,
2010
Air Force Institute of Technology
Relative Orbit Elements For Satellites In Elliptical Orbits, Kirk W. Johnson
Theses and Dissertations
The purpose of this research was to describe the unperturbed relative motion of Earth satellites in elliptical orbits using a simple dynamics model whose parameters allow significant geometrical insight and operational efficacy. The goal was to retain the advantages of the Relative Orbit Elements (ROE) realization of the Hill-Clohessy-Wiltshire (HCW) equations, a linearized dynamics model for circular reference orbits. Specifically, this thesis analyzed the geometry of satellite rendezvous and proximity operations using the ROE parameters to characterize the model’s utility. Next, through a comprehensive literature review, this thesis sought possible approaches for developing a similarly useful parameterization for chief orbits …
Mission Analysis And Design For Space Based Inter-Satellite Laser Power Beaming,
2010
Air Force Institute of Technology
Mission Analysis And Design For Space Based Inter-Satellite Laser Power Beaming, Nicholas M. Keller
Theses and Dissertations
This research effort develops an interdisciplinary design tool to optimize an orbit for the purpose of wirelessly beaming power from the International Space Stations (ISS) Japanese Experimental Module Exposed Facility (JEM/EF) to a target satellite. For the purpose of this initiative, the target satellite will be referred to as FalconSAT6, a reference to the proposed follow-on satellite to the U.S. Air Force Academy’s (USAFA) FalconSAT5 program. The USAFA FalconSAT program provides cadets an opportunity to design, analyze, build, test and operate small satellites to conduct Department of Defense (DoD) space missions. The tool developed for this research is designed to …
Estimating Characteristics Of A Maneuvering Reentry Vehicle Observed By Multiple Sensors,
2010
Air Force Institute of Technology
Estimating Characteristics Of A Maneuvering Reentry Vehicle Observed By Multiple Sensors, Evan M. Brooks
Theses and Dissertations
Post flight analysis of ballistic missile reentry vehicles is an area of focus for the U.S. Government, especially for those involved in ballistic missile defense. Typically, this analysis incorporates either a model-driven least squares filter or a data-following Kalman filter. The research performed here developed a filter that attempts to integrate the strengths of both filters. A least squares filter operates on observation data collected during exoatmospheric free flight and a Kalman filter is used to analyze data collected lower in the atmosphere, where potential maneuvers could be performed. Additionally, the filter was written to incorporate data from multiple sensors. …
Preliminary Electrical Designs For Ctex And Afit Satellite Ground Station,
2010
Air Force Institute of Technology
Preliminary Electrical Designs For Ctex And Afit Satellite Ground Station, Arthur L. Morse
Theses and Dissertations
This thesis outlines the design of the electrical components for the space-based ChromoTomography Experiment (CTEx). CTEx is the next step in the development of high-speed chromotomography at the Air Force Institute of Technology. The electrical design of the system is challenging due to the large amount of data that is acquired by the imager and the limited resources that is inherent with space-based systems. Additional complication to the design is the need to know the angle of a spinning prism that is in the field of view very precisely for each image. Without this precise measurement any scene that is …
Accurate Dynamic Response Predictions Of Pnpsat I,
2010
Air Force Institute of Technology
Accurate Dynamic Response Predictions Of Pnpsat I, Michael D. Trottier
Theses and Dissertations
Researchers at the Air Force Institute of Technology (AFIT) and the Operationally Responsive Space (ORS) Office have conducted extensive vibration testing and structural modeling on the first ORS Plug-and-Play Satellite (PnPSAT I). The intent of this research effort is to evaluate the premise that current post-integration spacecraft environmental test requirements can be reduced or modified using accurately tuned finite element (FE) models. As part of this research, modal testing was conducted on the PnPSAT I structural panels at AFIT. The modal testing was part of a much larger series of experimental trials on various configurations of PnPSAT I at the …
Mechanical Properties Characterization And Business Case Analysis Of The Fiber Metal Laminate Glare-3 For Use As Secondary Aircraft Structure,
2010
Air Force Institute of Technology
Mechanical Properties Characterization And Business Case Analysis Of The Fiber Metal Laminate Glare-3 For Use As Secondary Aircraft Structure, Benjamin O. Elton
Theses and Dissertations
This effort explored the mechanical characteristics and economic feasibility of using the fiber metal laminate, GLARE-3, as a secondary aircraft structure; specifically, the cargo floor of a C-130. The mechanical properties were determined through static four-point bending and tensile testing and dynamic impact testing. Aggregate behavior of the constituent materials was predicted using a model which consisted of Mass Volume Fraction (MVF) and Classical Laminated Plate Theory (CLPT) methods using known values for the constituents. Static testing was conducted on coupon-level specimens using standardized testing procedures. Static tensile tests were conducted on specimens with four different fiber orientations, 0°, 22.5°, …
Development Of Morphing Aircraft Structure Using Smp,
2010
Air Force Institute of Technology
Development Of Morphing Aircraft Structure Using Smp, Soo-Chan Jee
Theses and Dissertations
The U.S Air Force needs new aircraft which provide longer flight time, less fuel consumption, better aerodynamics in order to perform Air Force missions successfully as the mission environment changes rapidly. A morphing wing aircraft is considered as a potential new aircraft for those missions. This thesis explores Shape Memory Polymer (SMP) properties test results and its application for morphing wing skin. Several SMP composite laminates were considered for investigating shape changing characteristics required for morphing skin. The braided composite preforms used in making SMP composites were explored in morphing wing operating system based on the results of property tests. …
Aiding Gps With Additional Satellite Navigation Services,
2010
Air Force Institute of Technology
Aiding Gps With Additional Satellite Navigation Services, Yasin A. Mutlu
Theses and Dissertations
In modern warfare navigation services are very important. GPS is currently providing service for accurate navigation, except in some areas, especially urban areas, where GPS signals cannot always be tracked by users. In these cases some additional navigation support could be provided by other global navigation satellite systems. If GPS is combined with other navigation systems than the navigation gap will be minor. In this thesis, the effect of combining GPS with other satellite navigation systems, specifically GLONASS, Galileo and Compass, is evaluated in terms of availability and position dilution of precision (PDOP) values. First, satellite constellations are simulated in …
Development Of A Flapping Wing Design Incorporating Shape Memory Alloy Actuation,
2010
Air Force Institute of Technology
Development Of A Flapping Wing Design Incorporating Shape Memory Alloy Actuation, Jeffrey A. Barrett
Theses and Dissertations
This research sought to validate a proof of concept regarding shape memory alloy actuation of a flapping-wing blimp. Specimen wires were subjected to cyclic voltage at increasing frequencies to quantify expected strains. A laser vibrometer captured 2048 sample velocities during single contraction and elongation cycles, and the resulting samples were used to calculate displacements. Displacements were determined ten times for each specimen and frequency to compute averages. Subsequently, a circumventing frame was designed to encase a blimp envelope and provide support for a flapping motion actuation system. Contraction of shape memory wire translated force to the flapping mechanism via bellcranks, …
Part Count: Monolithic Part Effects On Manufacturing Labor Cost, An Aircraft Applied Model,
2010
Air Force Institute of Technology
Part Count: Monolithic Part Effects On Manufacturing Labor Cost, An Aircraft Applied Model, Aaron M. Lemke
Theses and Dissertations
There are significantly different manufacturing processes and part counts associated with composites that are not currently addressed within the aircraft procurement and life cycle management processes in the Department of Defense (DoD). A series of affordability initiatives have culminated in significant evidence over the last decade to better quantify the impact of primarily composite structures in aircraft. An Air Force Research Laboratory program, Advanced Composite Cargo Aircraft (ACCA), provides substantial support for the impact of part size on life cycle cost for payload aircraft. This research evaluates select methods used and seeks to introduce modifications to the projected manufacturing hours …
Verification Of Kam Theory On Earth Orbiting Satellites,
2010
Air Force Institute of Technology
Verification Of Kam Theory On Earth Orbiting Satellites, Christian L. Bisher
Theses and Dissertations
This paper uses KAM torus theory and Simplified General Perturbations 4 (SGP4) orbit prediction techniques compiled by Dr. William Wiesel and compares it to Analytical Graphics ® Incorporated (AGI) Satellite Toolkit ® (STK) orbit data. The goal of this paper is to verify KAM torus theory can be used to describe and propagate an Earth satellite orbit with similar accuracy to existing general perturbation techniques. Using SGP4 code including only truncated geopotential effects, KAM torus generating code, and other utilities were used to describe a particular satellite orbit as a torus and then propagate the satellite using traditional and KAM …
Numerical Investigation Of Pre-Detonator Geometries For Pde Applications,
2010
Air Force Institute of Technology
Numerical Investigation Of Pre-Detonator Geometries For Pde Applications, Robert T. Fievisohn
Theses and Dissertations
A parametric study was performed to determine optimal geometries to allow the successful transition of a detonation from a pre-detonator into the thrust tube of a pulse detonation engine. The study was performed using a two-dimensional Euler solver with progress variables to model the chemistry. The geometrical configurations for the simulations look at the effect of shock reflections, flow obstructions, and detonation diffraction to determine successful geometries. It was observed that there are success and failure rates associated with pre-detonators. These success rates appear to be determined by the transverse wave structure of a stably propagating detonation wave and must …
