Aerospace Engineering Commons^™

Flexi-Focus Lens: Pdms Variable Focal Length Lens, Patrick Angulo, Alex Doyle, Dylan Mcdaniel, Michael Olivarez

Industrial and Manufacturing Engineering

The design of a variable focal length, or flexi-focus, polydimethylsiloxane (PDMS) lens incorporating a light emitting diode (LED) source is intended for future use on board commercial aircraft. Specifically, the design is intended for the Boeing 787 Dreamliner aircraft, serving as a personal reading light for the passengers seated in the cabin. Most current reading lights on board aircraft are rigid, incandescent, and have very limited freedom in terms of adjusting the emitted light. Incandescent lamps are also inefficient with respect to energy consumption and light output as well as a high heat output. In an economy of increasing demand …

Human Powered Helicopter: Observing The Impacts Of Ground Effect And Intermeshed Rotors, Shane Stowe

Physics

No abstract provided.

Imu Integration To The Cal Poly Spacecraft Attitude Dynamics Simulator Power System, Wayland Chan

Electrical Engineering

The Cal Poly Spacecraft Attitude Dynamics Simulator mimics the rotation dynamics of a spacecraft in orbit and acts as a test bed for spacecraft attitude control system development and demonstration. Prior to this project, the simulator measured its attitude dynamics from a total of seven sensors mounted on to the platform, including three micro-electromechanical system (MEMs) gyroscopes, and four motor encoders. This project entails the installation of an LN-200 high performance gyroscope, which will provide a greater measure of accuracy. The goal of this project is to design a power circuit that will integrate the LN-200 inertial measurement unit onto …

Port Flow Test System, Daniel Chairez, Chelsea E. Crawford, Daniel S. Welch

Mechanical Engineering

Solar Turbines Gas Compressor Engineering Division of San Diego, California called upon the Mechanical Engineering students of California Polytechnic University, San Luis Obispo to provide recommendations for optimization of compressor end cap port design. Various sizes of compressors have end caps with numerous ports that exchange fluids between the inside and outside of the working fluid pressure vessel. Because so many ports must exist on the end caps, unusual flow paths are created to supply the appropriate location within the compressor. These flow paths commonly consist of a drilled inlet hole which intersects with a sudden expansion. The sudden expansion …

Cal Poly Human Powered Helicopter, Josiah Auer, Eric Behne, Dave Berry, Rebecca Hennings, James Koch, Ian Marquardt, Josiah Mayfield, Sean Miller

Mechanical Engineering

The following report encompasses the Cal Poly Human Powered Helicopter team’s efforts during the 2010-2011 academic year. The intention of this project is to further the knowledge of human powered helicopter design and to validate an ideal configuration through experimental tests and analysis. 

A. Background

The Sikorsky Prize offered by the American Helicopter Society has been the catalyst for many attempts at Human Powered Helicopter (HPH) flight. The requirement to win the prize is a continuous, human powered flight of more than 60 seconds that stays within a 10 meter square box and reaches an altitude greater than 3 meters …

Rayleigh Test Apparatus Design Report, Josef Duller, Owen Raybould, James Nicovich

Mechanical Engineering

The Rayleigh Test Apparatus is a device that will be used to test the thermodynamic properties of Nitrous Oxide to assess the feasibility of using this fluid as a coolant for a hybrid rocket aero spike. The aero spike is intended to redirect the propulsion flow as it leaves the engine to create a more efficient flow pattern at low and high altitudes. However, there are issues of overheating which leads to melting of the aero spike. For this reason, the use of nitrous oxide (N2O) as a coolant is being explored. N20 is being considered because it is already …

Boom Stability Control Final Project Report, Michael Barnes, Justin Carnahan, Daniel Fluitt, Alicia Johnstone

Mechanical Engineering

The BOOMStiC Gravity Gradient Boom and Turnstile Antenna project was developed to provide a passive attitude control system and better communications for future CubeSat satellites developed by California Polytechnic State University. The system utilizes the energy from a coilable metal spring to deploy a tip mass to a length of one meter from the side of the satellite. Calculations show the resulting gravity gradient torque causes to the satellite to settle two degrees from normal to the earth’s surface.

Development Of A Cubesat Instrument For Microgravity Particle Damper Performance Analysis, John Trevor Abel

Master's Theses

Spacecraft pointing accuracy and structural longevity requirements often necessitate auxiliary vibration dissipation mechanisms.  However, temperature sensitivity and material degradation limit the effectiveness of traditional damping techniques in space.  Robust particle damping technology offers a potential solution, driving the need for microgravity characterization.   A 1U cubesat satellite presents a low cost, low risk platform for the acquisition of data needed for this evaluation, but severely restricts available mass, volume, power and bandwidth resources.  This paper details the development of an instrument subject to these constraints that is capable of capturing high resolution frequency response measurements of highly nonlinear particle damper dynamics.

Hybrid Rocket Based Combined Cycle Test Rig Design, Construction, And Testing, Mark Costa, Matthew Handfelt

Aerospace Engineering

No abstract provided.

Construction Of Naca 66-415 Nlf Composite Wing For Acoustic Turbulence Testing, Scott Sawyer, Sean Stewart

Aerospace Engineering

A design is developed for a Natural Laminar Flow (NLF) wing, to be used at California Polytechnic State University for acoustic turbulence testing. Composite materials are used to produce high-quality surface finishes necessary for laminar flow. A design for the test apparatus is presented and justified. A manufacturing procedure is proposed for the carbon fiber skin, using Vacuum Resin Infusion (VRI). This procedure is tested on a scaled part with satisfactory results; lessons learned are discovered and integrated into the final manufacturing process. The test section has been fit to the Cal Poly wind tunnel, but full implementation has not …

A Space Based Particle Damper Demonstrator, John Brown

Master's Theses

The structure and payload of a CubeSat flight experiment that investigates the performance of particle dampers in a micro-gravity environment was designed, built, and tested, and will provide on orbit data for model validation and improved performance predictions for space applications of particle damping.

A 3-D solid model of the integrated CubeSat structure and payload was created satisfying all constraints from CubeSat and the System Dynamics Department at Northrop Grumman Aerospace Systems. The model was verified using commercially available Finite Element Analysis software (FEA), and a prototype structure part was fabricated. The prototype was tested and verified the FEA. A …

The Effects Of A Damage Arrestment Device On The Mechanical Behavior Of Sandwich Composite Beams Under Four-Point Bending, Richard Anthony Davis

Master's Theses

The demand for an insert on composite sandwich structures to aid in the arrestment of face-core delamination is of great need.  This research studies the use of a damage arrestment device (DAD) that connects the carbon fiber face sheets to the foam core to find whether an increase in the structural integrity of the sandwich beam results.  Experimental analysis was employed to test the samples and was verified by a theoretical and finite element approach.

The mechanical properties of LTM45/CF1803 pre-impregnated carbon fiber and Last-A-foam FR 6710 polyvinylchloride foam were experimentally analyzed using ASTM D3039 and ASTM D1621 standards respectively …

Designing The Human-Powered Helicopter: A New Perspective, Gregory Hamilton Gradwell

Master's Theses

The concept of human-powered vertical flight was studied in great depth. Through the manipulation of preexisting theory and analytical methods, a collection of design tools was created to expediently conceptualize and then analyze virtually any rotor. The tools were then arranged as part of a complete helicopter rotor design process. The lessons learned as a result of studying this process—and the tools of which it consists—are presented in the following discussion. It is the belief of the author that by utilizing these tools, as well as the suggestions that accompany them, future engineers may someday build a human-powered helicopter capable …

Adaptive Component Usage For The Thermal Management Of Picosatellites, William D. Whalen

Master's Theses

The CubeSat standard originated in 1999.  It was a joint development led by Dr. Jordi Puig-Suari of California State Polytechnic University San Luis Obispo and Professor Robert Twiggs of Stanford University. The engineering challenges that have come from this picosatellite class have created incredible educational opportunities for engineering students throughout the world.  Since the challenges of engineering a CubeSat abound the designers are always looking at novel and even revolutionary solutions to each one.  One of those opportunities is in thermal subsystem design, implementation and characterization.  A potential solution for CubeSats is adaptive component usage.

This thesis is the written …

Design Optimization Of Gaas Betavoltaic Batteries, Haiyanag Chen, Lan Jiang, Xuyuan Chen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

GaAs junctions are designed and fabricated for beta voltaic batteries. the design is optimized according to the characteristics of GaAs interface states and the diffusion length in the depletion region of GaAs carriers. under an illumination of 10 mCi cm-263Ni, the open circuit voltage of the optimized batteries is about ∼0.3 V. It is found that the GaAs interface states induce depletion layers on P-type GaAs surfaces. the depletion layer along the P+PN+ junction edge isolates the perimeter surface from the bulk junction, which tends to significantly reduce the battery dark current and leads to a high open circuit voltage. …

Review Of The Maxus 8 Sounding Rocket Experiment To Investigate Solidification In A Ti-Al-Nb Alloy, Robin Mooney, David Browne, Olga Budenkova, Yves R. Fautrelle, Ludo Froyen, Andrey Kartavykh, Stephan Rex, Burkhard Schmitz, Daniella Voss, Shaun Mcfadden

Conference Papers

A review of the MAXUS 8 sounding rocket microgravity experiment to investigate solidification structures in a Ti-Al-Nb intermetallic alloy is presented. The experiment was part of the Intermetallic Materials Processing in Relation to Earth and Space Solidification (IMPRESS) EU FP6 project. Key objectives were to investigate columnar and equiaxed solidification, and to achieve Columnar-to-Equiaxed Transition (CET) in the alloy. A microgravity experiment was designed to achieve this using a controlled power-down method. Two alloys were tested: one inoculated with a grain refiner and the other without grain refinement. Unrefined samples displayed axial and radial columnar growth. Boride inoculated samples displayed …

Deployment And Characterisation Of A Telescopic Boom For Sounding Rockets, Johnalan Keegan, Mark Wylie, Stephen Curran, Dinesh Vather, Paul Duffy

Conference Papers

In any sounding rocket, volume and mass are at a premium. Payload designers strive towards smaller, lighter and cheaper mechanisms which can achieve the same goals. This project aims to reduce the mass and volume for probe deployment booms and their deployment mechanisms. An experiment (Telescobe) to test a low cost novel method of boom deployment using telescopic carbon fibre poles was developed. A custom camera measurement system was also developed to measure boom length and harmonic deflection. This experiment was flown onboard the REXUS 9 sounding rocket [1] in February 2011 from Esrange space centre, Sweden. The experiment functioned …

Development Of A Laboratory Experiment To Simulate Upper-Stage Rocket Explosions, Timothy J. Price

Aerospace Engineering

This report is a summary of the senior project entitled Development of a Laboratory Experiment to Simulate Upper-Stage Rocket Explosions. The goal of the experiment was to recreate a NASA experiment which used aluminum soft drink cans to approximate the shape of an Ariane third stage rocket. The cans were placed in a vacuum chamber and fired upon with a projectile from a light gas gun. The resulting debris was collected and analyzed allowing several conclusions to be made regarding the behavior or rocket breakups and the formation of space debris. In lieu of a light gas gun, energy drink …

Airplane Landing Flare-The Last 5 Seconds, Nihad E. Daidzic

Aviation Department Publications

No abstract provided.

Primary And Secondary Flow Structures In A Model Cerebral Aneurysm, Morgan A. Nowak

Renée Crown University Honors Thesis Projects - All

Cerebral aneurysms affect 5% of western populations and can cause morbidity and mortality if they rupture. Various treatments can be used to minimize the risk of rupture, with new diagnostics and treatments under development that require information from non-invasive techniques such as Particle Imaging Velocimetery (PIV). The current study focused on developing a setup as a basis for future experiments and work on intracranial aneurysms involving PIV. PIV experimentation and data collection were carried out during the summer of 2010 at Ohta Labs of Tohoku University in Sendai, Japan. The experimental setup consisted of a pulsatile flow system, which was …