Aerospace Engineering Commons^™

An Investigation Of U.S. Orbital Debris Policy Changes To Support Leo Conservation, Thomas Percy

Von Braun Symposium Student Posters

No abstract provided.

Validation Of The Ballistic Limit Equation For Monolithic Aluminum Shielding At Geostationary Orbital Debris Impact Velocity, Brandon Holladay

Aerospace Engineering

The Cal Poly Electro Magnetic Rail Gun was used to eject a 0.370 gram, rectangular aluminum projectile towards a 1/16 inch monolithic aluminum plate at a speed of 280 ± 50 m/s. The resulting impact left a large attached spall on the back of the shielding. The impact damage was compared to an industry ballistic limit equation for a spherical aluminum projectile of similar diameter and was shown to have slightly less damage than the expected results.

In addition, an aluminum mesh double bumper shield was fired upon in order to verify its higher protection per aerial density as well …

Three-Axis Stabilized Earth Orbiting Spacecraft Simulator, Alan F. Ma, Nikola N. Dominikovic

Aerospace Engineering

This report details the method and results of the program created for simulating an Earth orbiting spacecraft with control actuators and orbital perturbations. The control actuators modeled are reaction thrusters, reaction/momentum wheels, and control moment gyros (CMG). The perturbations modeled were gravity gradient, electromagnetic torques, solar radiation pressure, gravity gradients, third-body effects, Earth oblateness and atmospheric drag. This simulation allows for satellite control in all 6 degrees of freedom for any Earth orbiting spacecraft. Assumptions include rigid body dynamics, no sensor noise, constant spacecraft cross-sectional area, constant coefficient of drag and reflectivity, ignoring the effects due to the moon, moment …

Strain Rate And Orientation Dependencies Of The Strength Of Single Crystalline Copper Under Compression, Virginie Dupont, Timothy C. Germann

Aerospace Engineering - Daytona Beach

Molecular dynamics (MD) simulations are used to model the compression under uniaxial strain of copper single crystals of different orientations at various temperatures and strain rates. Uniaxial strain is used because of the close resemblance of the resulting stress state with the one behind a shock front, while allowing a control of parameters such as strain rate and temperature to better understand the behavior under complex dynamic shock conditions. Our simulations show that for most orientations, the yield strength of the sample is increased with increasing strain rate. This yield strength is also dependent on the orientation of the sample, …

Structural Damage Classification Using Support Vector Machines, Xiang Li

Doctoral Dissertations and Master's Theses

In this research, a methodology to classify crack and corrosion metallic damages using a time-frequency representation method and support vector machines is investigated. Piezoelectric ceramic actuators are utilized to generate guided wave signals on a set of aluminum beam coupons with different damage features, such as types, locations, and thicknesses. The short-time Fourier transform is applied to analyze the measured signals. For damage classification, the spectrograms obtained from finite element models are employed to train a two-class support vector machine learning classifier. The classifier is able to correctly classify different types of damages based upon the measured signals collected from …

Modification And Application Of A Turbulence Response Analysis Method For Flexible Aircraft Configurations, Christie Jeanne Funk

Mechanical & Aerospace Engineering Theses & Dissertations

A software program and associated methodology to study gust loading on aircraft exists for a classification of geometrically simplified flexible configurations. This program consists of a simple aircraft response model with two rigid and three flexible symmetric degrees of freedom and allows for the calculation of various airplane responses due to a discrete one-minus-cosine gust as well as continuous turbulence. Simplifications, assumptions, and opportunities for potential improvements pertaining to the existing software program are first identified, then a revised version of the original software tool is developed with improved methodology to include more complex geometries, additional excitation cases, and output …

Configuration Studies Of Electrostatic And Magnetostatic Active Space Radiation Shielding, Trac K. Nguyen

Electrical & Computer Engineering Theses & Dissertations

Developing successful and optimal solutions for mitigating the hazards of radiation in deep space is critical for the success of deep-space long duration explorations, including mission to the Moon, Mars and beyond. A recent report (Tripathi et al., 2008) had explored the feasibility of using electrostatic shielding in conjunction with state-of-the-art materials shielding technologies.

In this thesis research, we study the active electrostatic shielding strategy and examine a hybrid configuration that utilizes both electrostatic and magnetostatic fields. The main advantages of this system are shown to be: (i) much lower magnetic fields that could be below the thresholds set for …

Neural Network Fatigue Life Prediction In Steel I-Beams Using Mathematically Modeled Acoustic Emission Data, Prathikshen Nambiar Selvadorai

Doctoral Dissertations and Master's Theses

The purpose of this research is to predict fatigue cracking in metal beams using mathematically modeled acoustic emission (AE) data. The AE data was collected from nine samples of steel I-beam that were subjected to three-point bending caused by cyclic loading. The data gathered during these tests were filtered in order to remove long duration hits, multiple hit data, and obvious outliers. Based on the duration, energy, amplitude, and average frequency of the AE hits, the filtered data were classified into the various failure mechanisms of metals using NeuralWorks® Professional II/Plus software based self-organizing map (SOM) neural network. The parameters …

Acoustic Emission Signal Classification For Gearbox Failure Detection, Jun Shishino

Doctoral Dissertations and Master's Theses

The purpose of this research is to develop a methodology and technique to determine the optimal number of clusters in acoustic emission (AE) data obtained from a ground test stand of a rotating H-60 helicopter tail gearbox by using mathematical algorithms and visual inspection. Signs of fatigue crack growth were observed from the AE signals acquired from the result of the optimal number of clusters in a data set. Previous researches have determined the number of clusters by visually inspecting the AE plots from number of iterations. This research is focused on finding the optimal number of clusters in the …

Modeling Martian Planetary Entry Descent And Landing Using Monte Carlo Driven Response Surface Methodology, Narcrisha S. Norman

Mechanical & Aerospace Engineering Theses & Dissertations

Response surface methodology (RSM) is a statistical method that explores the relationships between several descriptive variables and one or more response variables. For over sixty years, among other areas, it has been utilized in quality engineering, process engineering, aircraft engineering, economics, chemical engineering, automotive engineering and design/technique optimization. In this dissertation, RSM is utilized to produce regression models that represent the planetary entry, descent and landing (EDL) process. A complete understanding of EDL process is an essential component of any planetary exploration. Research in this area is ongoing and confidence in the ability to explore known celestial bodies is growing. …

Educating Undergraduate Space Science Students With Real Space Missions: Nanosatellite And Nanolab Missions In Kentucky, Robert J. Twiggs

Robert "Bob" Twiggs STEM Education Collection

A PowerPoint presentation created by Professor Bob Twiggs titled "Educating Undergraduate Space Science Students with Real Space Missions: NanoSatellite and NanoLab Missions in Kentucky" from September 27, 2012.

Effect Of Accessory Power Take-Off Variation On A Turbofan Engine Performance, Anis Faidi

Theses and Dissertations

Engine fuel efficiency of aerospace vehicles can be reached by different techniques. One way to do that is to reduce aircraft subsystems power supply effects on the engine performance. Previous research work has showed that extracting bleed air from the high pressure compressor exit is more efficient than extracting the equivalent amount of energy from the low pressure spool shaft. A high bypass turbofan engine was modeled using the Numerical Propulsion System Simulation (NPSS). The baseline engine performance was evaluated at different flight conditions of Mach number and altitude. To better understand the effect of air bleed take-off and shaft …

Fundamental Sizing Implications Of Constant Or Increasing Weight Aircraft, Robert A. Mcdonald

Aerospace Engineering

As the energy storage capabilities of batteries and fuel cells advance, these technologies are increasingly being considered for aircraft primary propulsion. In addition to other fundamental differences from conventional systems, these concepts may have constant or even increasing mass throughout the mission. In this paper, the implications of constant or increasing mass on aircraft sizing are considered with the aim of generating insight for the design of these systems.

Scaling Study Of Wave Rotor Turbo-Normalization Of A Small Internal Combustion Engine, Brandon D. Smith

Theses and Dissertations

One issue facing small Remotely Piloted Aircraft engines is their ability to maintain performance at altitude. Since many of these aircraft use commercial off the shelf engines originally designed for radio controlled aircraft and lawn care implements, the reduced pressure environment significantly degrades the operability of the engine as the altitude increases. An option to overcome this difficulty is to supercharge the system; however most superchargers are designed for larger, typically automotive, engines. As a supercharger's size is decreased, there are large efficiency losses. Therefore, there is a need to accomplish this function on a smaller scale without. One option …

A (Declassified) History Of Military Drones, Stephen Rayleigh

ERAU Prescott Aviation History Program

Unmanned Aerial Vehicles or drones, are said to be the newest technology of contemporary warfare, but the military's use of drones spans the last 100 years. Hear the riveting story of the numerous secret UAV programs around the world, starting with the Sperry Aerial Torpedo Project in 1918 (consulted by Orville Wright), the German cruise missile program, American remote controlled bombers in WWII, the Firebee recon drone used in Vietnam, Israel's highly successful UAV program, and finally the coming of age of UAV's in Operation Desert Storm.

Investigation Into Suitability Of Geopolymers (Illite & Metakaolin) For The Space Environment, Brandon T. Cesul

Theses and Dissertations

Suitability of non-organic polymers for space application is studied. Materials included are illite and metakaolin. Bulk material suitability was investigated for exposure to ultraviolet radiation, atomic oxygen, and high energy charged particles. Outgassing phenomenon of the materials was studied. Curing shrinkage reduction techniques were identified as well.

Operationally Responsive Spacecraft Using Electric Propulsion, Thomas C. Co

Theses and Dissertations

A desirable space asset is responsive and flexible to mission requirements, low-cost, and easy to acquire. Highly-efficient electric thrusters have been considered a viable technology to provide these characteristics; however, it has been plagued by limitations and challenges such that operational implementation has been severely limited. The technology is constantly improving, but even with current electric propulsion, a spacecraft is capable of maneuvering consistently and repeatedly in low-Earth orbit to provide a responsive and flexible system. This research develops the necessary algorithm and tools to demonstrate that EP systems can maneuver significantly in a timely fashion to overfly any target …

Novel Discretization Schemes For The Numerical Simulation Of Membrane Dynamics, Kyle F. Kolsti

Theses and Dissertations

Motivated by the demands of simulating flapping wings of Micro Air Vehicles, novel numerical methods were developed and evaluated for the dynamic simulation of membranes. For linear membranes, a mixed-form time-continuous Galerkin method was employed using trilinear space-time elements, and the entire space-time domain was discretized and solved simultaneously. For geometrically nonlinear membranes, the model incorporated two new schemes that were independently developed and evaluated. Time marching was performed using quintic Hermite polynomials uniquely determined by end-point jerk constraints. The single-step, implicit scheme was significantly more accurate than the most common Newmark schemes. For a simple harmonic oscillator, the scheme …

The Characterization Of Material Properties And Structural Dynamics Of The Manduca Sexta Forewing For Application To Flapping Wing Micro Air Vehicle Design, Ryan P. O'Hara

Theses and Dissertations

The Manduca Sexta species of moth serves as a source of biological inspiration for the future of micro air vehicle flapping flight. The ability of this species to hover in flapping flight has warranted investigation into the critical material, structural, and geometric properties of the forewing of this biological specimen. A rigorous morphological study of the Manduca Sexta forewing was conducted to characterize the physical and material properties of the biological forewing for the purpose of developing an advanced parametric three dimensional model finite element analysis (FEA) model. This FEA model was tuned to match the experimentally determined structural dynamics …

Novel Crankshaft Mechanism And Regenerative Braking System To Improve The Fuel Economy Of Light Duty Vehicles And Passenger Cars, Alberto A. Boretti, Joseph Scalzo

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Improvements of vehicle fuel economy may be achieved by the introduction of advanced internal combustion engines (ICE) improving the fuel conversion efficiency of the engine and of advanced power trains (PWT) reducing the amount of fuel energy needed to power the vehicle. the paper presents a novel design of a variable compression ratio advanced spark ignition engine that also permits an expansion ratio that may differ from the compression ratio hence generating an Atkinson cycle effect. the stroke ratio and the ratio of maximum to minimum in-cylinder volumes may change with load and speed to provide the best fuel conversion …