Aerospace Engineering Commons^™

Evaluation Of Additively Manufactured Lattices Under High Strain Rate Impact, Derek G. Spear

Theses and Dissertations

Several additively manufactured lattice designs and configurations were evaluated under compression loads under various strain rates from quasi-static to highly dynamic. These experiments examined how the mechanical behavior of the lattice changed based on the lattice design properties and the applied strain rates. The modulus of elasticity, yield strength, plateau stress, and toughness were observed to decrease with an increase in strain rate, revealing that the lattice designs exhibit a negative strain rate sensitivity. A new lattice flow stress model was developed to account for the mechanical response of the lattice and was incorporated into a computational model for simulation. …

Blade Optimization For Ground Level Low Speed Wind Turbines, Ryan Foster

Symposium of Student Scholars

Low speed wind turbines can provide inexpensive and clean energy in areas where large scale wind power generation is impractical. The purpose of this research is to explore factors that affect the efficiency of low speed wind turbine blades. The factors that were tested include angle of attack, angle of twist, chord length, average thickness, span, and taper ratio. The goal is to determine a combination of these variables to enable maximum power extraction from a low wind speed source. These blade parameters are optimized for the Southeastern region of the United States. NOAA weather data at ground level are …

Lifting Flow Over A Cylinder As A Lift System, Kyle Mello

Symposium of Student Scholars

The goal of this project is to conceptually design a lift system consisting of rotating cylinders that may improve certain flight characteristics when compared to conventional wings for a typical two passenger airplane. The functions of flaps, ailerons, lift to weight ratio and structural responses are considered. The cylindrical model is developed within CFD simulation software such that it generates the same lift produced by the wings of a Cessna 172 wings at cruising speed. Incompressible flow theoretical solutions are initially shown to compare favorably with the computational predictions for elementary cylindrical designs.

The rotating cylinder aircraft generates the same …

Modeling Dewetting, Demixing, And Thermal Effects In Nanoscale Metal Films, Ryan Howard Allaire

Dissertations

Thin film dynamics, particularly on the nanoscale, is a topic of extensive interest. The process by which thin liquids evolve is far from trivial and can lead to dewetting and drop formation. Understanding this process involves not only resolving the fluid mechanical aspects of the problem, but also requires the coupling of other physical processes, including liquid-solid interactions, thermal transport, and dependence of material parameters on temperature and material composition. The focus of this dissertation is on the mathematical modeling and simulation of nanoscale liquid metal films, which are deposited on thermally conductive substrates, liquefied by laser heating, and subsequently …

Modeling And Design Optimization For Membrane Filters, Yixuan Sun

Dissertations

Membrane filtration is widely used in many applications, ranging from industrial processes to everyday living activities. With growing interest from both industrial and academic sectors in understanding the various types of filtration processes in use, and in improving filter performance, the past few decades have seen significant research activity in this area. Experimental studies can be very valuable, but are expensive and time-consuming, therefore theoretical studies offer potential as a cost-effective and predictive way to improve on current filter designs. In this work, mathematical models, derived from first principles and simplified using asymptotic analysis, are proposed for: (1) pleated membrane …

The Influence Of Trailing Edge Shape And Kinematics On Bio-Inspired Pitching Panels, Justin Thomas King

Dissertations - ALL

Recently, some engineers have turned to the study of swimming and flying animals to provide insight into the design of vehicles that move through air or water. For certain animals swimming in water, thrust is generated primarily by either a caudal fin or fluke located at the posterior end of the swimmer. It has been argued extensively in the existing research literature that biological propulsors of high aspect ration that also display forked, or lunate, planforms are representative of optimized propulsor geometries with respect to propulsive performance. However, recent experimental and computational work on purely pitching panels has demonstrated that …

Flow Interaction Between Turbomachine Blade Row And Flow Resistance Medium, Tong Lin

Dissertations - ALL

This research investigates the fluid-dynamic interaction between close-coupled axial turbomachines and surrounding components, e.g., heat-exchangers, filters, or cooling fins in high-density computer servers, and its effects on turbomachine and system performance. The importance of this research is that the flow interaction effect occurs in every scenario that requires system compactness.

Firstly, a combined experimental and 3-D computational study on an off-the-shelf server cooling fan is performed, showing that the fan performance has little changed. However, the system performance can be very different since the server cooling has a large hub-to-tip radius ratio, which effectively blocks the high resistance media's (HRM) …

Application Of Net-Centric Communications For Disasters (Panel 1: First Responder), Norman Jones

Online Journal of Space Communication

Norman Jones, Transformational Communications Engineering presents: Application of Net-Centric Communications for Disasters

White Paper On Emergency Communications, Space And Advanced Communications Research Institute Space And Advanced Communications Research Institute

Online Journal of Space Communication

Prepared by the Space & Advanced Communications Research Institute (SACRI)

George Washington University

January 5, 2006

Note: This White Paper draws a number of sources including presentations at the National Conference on Emergency Communications (NCEC) held at the George Washington University on December 12-13, 2005. This conference featured some thirty different speakers selected from the federal as well as state and local governments, a wide range of industry spokespeople, several professional societies, relief organizations and NGOs, universities, and other interested parties. There were thirty different sponsors. These presentations, the attendees at this conference and the many sponsors of this event …

Issue 10: From The Guest Editors, Joseph Pelton, Neil Helm

Online Journal of Space Communication

Issue 10 introduction from the guest editors.

Euler's Three-Body Problem, Sylvio R. Bistafa

Euleriana

In physics and astronomy, Euler's three-body problem is to solve for the motion of a body that is acted upon by the gravitational field of two other bodies. This problem is named after Leonhard Euler (1707-1783), who discussed it in memoirs published in the 1760s. In these publications, Euler found that the parameter that controls the relative distances among three collinear bodies is given by a quintic equation. Later on, in 1772, Lagrange dealt with the same problem, and demonstrated that for any three masses with circular orbits, there are two special constant-pattern solutions, one where the three bodies remain …

Small Hall Effect Thruster With 3d Printed Discharge Channel: Design And Thrust Measurements, Ethan P. Hopping, Wensheng Huang, Kunning G. Xu

PRC-Affiliated Research

Citation: Hopping, E.P.; Huang, W.; Xu, K.G. Small Hall Effect Thruster with 3D Printed Discharge Channel: Design and Thrust Measurements. Aerospace 2021, 8, 227. https:// Abstract: This paper presents the design and performance of the UAH-78AM, a low-power small Hall effect thruster. The goal of this work is to assess the feasibility of using low-cost 3D printing to create functioning Hall thrusters, and study how 3D printing can expand the design space. The thruster features a 3D printed discharge channel with embedded propellant distributor. Multiple materials were tested including ABS, ULTEM, and glazed ceramic. Thrust measurements were obtained at the …

Small Hall Effect Thruster With 3d Printed Discharge Channel: Design And Thrust Measurements, Ethan P. Hopping, Wensheng Huang, Kunning G. Xu

PRC-Affiliated Research

Citation: Hopping, E.P.; Huang, W.; Xu, K.G. Small Hall Effect Thruster with 3D Printed Discharge Channel: Design and Thrust Measurements. Aerospace 2021, 8, 227. https:// Abstract: This paper presents the design and performance of the UAH-78AM, a low-power small Hall effect thruster. The goal of this work is to assess the feasibility of using low-cost 3D printing to create functioning Hall thrusters, and study how 3D printing can expand the design space. The thruster features a 3D printed discharge channel with embedded propellant distributor. Multiple materials were tested including ABS, ULTEM, and glazed ceramic. Thrust measurements were obtained at the …

Space Opens Its Doors To Unexpected Players, One Of Them Paraguay, Macarena Carrizosa

Capstones

Paraguay successfully sent its first native satellite into orbit in 2021, proving how essential and accessible the industry has become, even for developing countries. This article looks at how knowledge and technology transfer programs combined with a lower cost of entry helped Paraguay reach its first major milestone in the space industry, having its own satellite.

Lightning Arc Channel Effects On Surface Damage Development On A Prseus Composite Panel: An Experimental Study, Dounia Boushab, Pedram Gharghabi, Juhyeong Lee, Thomas E. Lacy Jr., Charles U. Pittman Jr., Michael S. Mazzola, Alexander Velicki

Mechanical and Aerospace Engineering Faculty Publications

Composite aircraft structures are vulnerable to lightning strike damage due to their relatively low electrical and thermal conductivities. A preceding work has investigated the lightning damage resistance of a carbon-epoxy Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) panel. The damage includes intense local damage (i.e., matrix decomposition/sublimation, fiber rupture, delamination) accompanied by widespread surface damage (i.e., distributed fiber rupture and tow splitting) further from the lightning attachment point. This study focuses on investigating the cause of the widespread surface damage. Two possible driving mechanisms are explored: i) magnetically-induced currents and ii) lightning arc-root/channel expansion. …

Robust Nonlinear Tracking Control For Unmanned Aircraft In The Presence Of Wake Vortex, Petr Kazarin, Vladimir Golubev, William Mackunis, Claudia Moreno

Publications

The flight trajectory of unmanned aerial vehicles (UAVs) can be significantly affected by external disturbances such as turbulence, upstream wake vortices, or wind gusts. These effects present challenges for UAV flight safety. Hence, addressing these challenges is of critical importance for the integration of unmanned aerial systems (UAS) into the National Airspace System (NAS), especially in terminal zones. This work presents a robust nonlinear control method that has been designed to achieve roll/yaw regulation in the presence of unmodeled external disturbances and system nonlinearities. The data from NASA-conducted airport experimental measurements as well as high-fidelity Large Eddy Simulations of the …

Radiation Effects On Space Solar Cells At Various Earth And Jupiter Orbital Altitudes, Naazneen Rana

Discovery Undergraduate Interdisciplinary Research Internship

Solar cells are used as the primary power source for earth-orbiting satellites and as a primary/secondary power source for various missions within the solar system. However, high energy particles from the sun, planetary magnetospheres, and the galaxy can affect the performance and life expectancy of the space solar cell and associated power systems. As the interests for interplanetary travel and the exploration of planets within our solar system increase, the need to understand a device’s performance within a particular planet’s environment is necessary. Therefore, this study will analyze the performance of space solar cells, particularly the SolAero IMM-α, at various …

Unmanned Aircraft Systems For Archaeology Using Photogrammetry And Lidar In Southwestern United States, Imai Bates-Domingo, Alexandra Gates, Patrick Hunter, Blake Neal, Kyle Snowden, Destin Webster

Study America

Researchers can use small unmanned aircraft systems (sUAS), also known as drones, to make observations of historical sites, help interpret locations, and make new discoveries that may not be visible to the naked eye. A student team from Embry-Riddle Aeronautical University gathered data for historical site documentation in New Mexico using the DJI Phantom 4 Pro V2, DJI Mavic Pro 2, DJI M210 and DJI M600, and senseFly eBee. Utilizing these drones, student analysts were able to take the data gathered and create georectified orthomosaic images and 3D virtual objects. At Tularosa Canyon, at a site known as the Creekside …

Stress Analysis Of Functionally Graded Materials, Nilabh Krishna

Mechanical and Aerospace Engineering Dissertations - Archive

A functionally graded material (FGM) is an inhomogeneous material whose material properties vary continuously. Since FGM’s material properties are continuous at the interface of the two materials, unlike conventional composites whose material properties are discontinuous at the interface, it is best suited to prevent catastrophically failure, stress concentration, and residual stresses. Literature reviews revealed that most of the research on FGMs was a 2-D analysis, especially on FGM plates and beams. This research focuses on 3-D stress analysis for an elastic medium that contains a spherical inclusion made of an FGM embedded in a matrix phase. To the best of …

Effect Of Thermal Conductivity, Reynolds Number, Aspect Ratio And Packing Arrangement On Radial Heat Transfer In Packed Beds, Nishith Gorla

Mechanical and Aerospace Engineering Dissertations - Archive

The key motivation for this research is to study heat transfer developments in packed beds. The radial heat transfer enhancement of a packed bed in the laminar flow region is one of the major areas of ongoing research in mechanical, aerospace and chemical industries, especially the response of a packed bed during conjugate heat transfer with the fluid-solid interaction. This computational study focuses on the impact of packing size, thermal conductivity, and arrangement on the radial heat transfer performance as a function of Reynolds number. A simple annular tube packed with circles (2D) and spheres (3D) is utilized for this …