Aerodynamics and Fluid Mechanics Commons^™

Application Of Strand-Cartesian Interfaced Solver On Flows Around Various Geometries, Yushi Yanagita

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

This work examines the application of a high-order numerical method to strand-based grids to solve the Navier-Stokes equations. Coined "Flux Correction", this method eliminates error terms in the fluxes of traditional second-order finite volume Galerkin methods. Flux Correction is first examined for applications to the Reynolds-Averaged Navier-Stokes equations to compute turbulent flows on a strictly strand-based domain. Flow over three geometries are examined to demonstrate the method’s capabilities: a three-dimensional bump, an infinite wing, and a hemisphere-cylinder configuration. Comparison to results obtained from established codes show that the turbulent Flux Correction scheme accurately predicts flow properties such as pressure, velocity …

Extended Surface Heat Transfer Coefficients Via Endwall Temperature Measurements, Yogesh Pai

Doctoral Dissertations and Master's Theses

Short pins are used for internal cooling of the trailing edge in a gas turbine blade. A novel method is described in this thesis which helps in simplifying the experimental process used to obtain average heat transfer data on the pin surface, at the expense of additional post processing complexity. The method is based on a unique, analytical solution of the longitudinal conduction equation with internal heat generation, allowing computation of heat transfer rates via pin base temperature measurements via Temperature Sensitive Paint, or similar non-intrusive methods. Verification of this method is done with comparisons to the solution of infinite …

A Performance And Visualization Study On Inlet Geometries Of A Cross-Flow Fan., Yoel Tanquero

Electronic Theses and Dissertations

A study was conducted to characterize the flow-field in the suction region of different inlet geometries of a cross-flow fan. The characterization was accomplished by correlating the static performance curves measured for each fan-inlet configuration to the streamline plot obtained using a particle tracking velocimetry (PTV) measurement system at three constant flow rates (25, 40, and 55 CFM). The PTV measurement system used was developed by the author and uses helium bubbles as tracers, an LED light sheet, a slow motion camera, and a Matlab program. Four inlet geometry design variables were defined and independently studied to evaluate the effect …

Investigation Of Dynamic Store Separation Out Of A Weapons Bay Cavity Utilizing A Low Speed Wind Tunnel, Andrew D. Bower

Theses and Dissertations

Characterizing mission store trajectories as they separate from a weapons bay cavity is highly relevant to the Air Force mission. The flow around a weapons bay is unsteady. The unsteady flow can cause a mission store separation trajectory to be unpredictable, and such is the case for what some have termed a pitch bifurcation. Traditional wind tunnel testing is incapable of detecting a bifurcation because traditional wind tunnel testing records time-averaged data. In this study, an experimental testing system was developed and refined in order to support the time-accurate characterization of dynamic mission store separation events. A Motion Test Apparatus …

Time-Dependent Validation Of Finite Element Strain Distribution Of A Plastically-Deformed Plate Via Digital Image Correlation, Kevin R. Knapp

Theses and Dissertations

Generation of residual stress is an essential step in the generation of Goodman data via Air Force Research Laboratory's vibration-based fatigue test. Conventional Goodman data is constructed through uniaxial fatigue testing at a rate of 40 Hz, while the vibration-based testing excites stresses at 1,600 Hz in a stress state that is similar to those seen in gas turbine engine airfoils. A pre-strain procedure is conducted to form residual tensile stress, which serves as a steady stress when the specimen is subjected to fully-reversed vibration-based fatigue loads. This steady tensile stress is desired at the fatigue zone of the test …

In-House Fabrication Of Temperature Sensitive Paint For Turbine Cooling Research, Mayur D. Patel, Mark A. Ricklick

Beyond: Undergraduate Research Journal

The Temperature Sensitive Paint (TSP) is a widely used method in measuring and visualizing flow separation and heat transfer. Compared to the cost and time consumption needed for methods such as pitot tubes, temperature sensitive paint is a cheaper alternative. Due to high usage in College of Engineering research projects, it was determined that in house fabrication of temperature sensitive paint would reduce time and cost limitations. For initial stages, literature research was performed to determine the recipe of intensity based TSP with luminophore and polymer binder that operated optimum at temperatures from 0-100°C. Europium III thenoyltrifluoroacetonate was determined to …

An Archival Analysis Of Stall Warning System Effectiveness During Airborne Icing Encounters, John Michael Maris

Doctoral Dissertations and Master's Theses

An archival study was conducted to determine the influence of stall warning system performance on aircrew decision-making outcomes during airborne icing encounters. A Conservative Icing Response Bias (CIRB) model was developed to explain the historical variability in aircrew performance in the face of airframe icing. The model combined Bayes’ Theorem with Signal Detection Theory (SDT) concepts to yield testable predictions that were evaluated using a Binary Logistic Regression (BLR) multivariate technique applied to two archives: the NASA Aviation Safety Reporting System (ASRS) incident database, and the National Transportation Safety Board (NTSB) accident databases, both covering the period January 1, 1988 …

Rans Simulations Of Aerodynamic Performance Of Naca 0015 Flapped Airfoil, Sohaib Obeid, Ratneshwar Jha, Goodarz Ahmadi

Henry M. Rowan College of Engineering Departmental Research

An analysis of 2D subsonic flow over an NACA 0015 airfoil with a 30% trailing edge flap at a constant Reynolds number of 106 for various incidence angles and a range of flap deflections is presented. The steady-state governing equations of continuity and momentum conservation are solved combined with the realizable k-ε turbulence model using the ANSYS-Fluent code (Version 13.7, ANSYS, Inc., Canonsburg, PA, USA). The primary objective of the study is to provide a comprehensive understanding of flow characteristics around the NACA 0015 airfoil as a function of the angle of attack and flap deflection at Re = 106 …

Multi-Stage Axial Compressor With Counter-Rotation, Vinod Gehlot, Magdy S. Attia, Divyam Garg

Publications

A multi-stage axial compressor incorporating a counter-rotational movement is provided with a series of rotors mounted along and driven by a driveshaft, and a geared counter-rotating outer casing. A planetary gear system is assembled along a static casing, which can be assembled as a forward or aft casing for the compressor. The bearings of the planetary gear system typically will be aligned concentrically with a center rotor drum assembly mounted along the single driveshaft. The counter-rotating drum assembly will be assembled over the rotor drum assembly and will be engaged by the forward and aft casings so as to provide …

Design And Modeling Of A Heat Exchanger For Porous Combustor Powered Steam Generators In Automotive Industry, Apratim Dasgupta

Electronic Theses and Dissertations

A major challenge faced by automobile manufacturers is to achieve reduction of particulate emission to acceptable standards, as the emission standards become more and more stringent. One of the ecologically friendly options to reduce emissions is to develop external combustion in a steam engine as a replacement of the internal combustion engine. There are multiple factors, other than pollution that need to be considered for developing a substitute for Internal Combustion Engine, like specific power, throttle response, torque speed curve, fuel consumption and refueling infrastructure. External combustion in a steam engine seems to be a bright idea, for a cleaner …

Implementation Of Optical Interferometry And Spectral Reflectometry For High Fidelity Thin Film Measurements, Armando Arends-Rodriguez

Electronic Theses and Dissertations

An in-house reflectometer/interferometer has been built to investigate the varying curvature and thickness profiles in the contact line region of air, acetone, iso-octane, ethanol, and water on various types of substrates. Light intensity measurements were obtained using our reflectometer/interferomter and then analyzed in MATLAB to produce thickness and curvature profiles. The apparatus is based on the principle of a reflectometer, consisting of different optical elements, probe, light source, and spectrometer. Our reflectometer/interferomter takes measurements in the UV-Vis-IR range (200nm-1000nm). This range is achieved by using a light source that has both a deuterium light (190nm-800nm), a tungsten halogen light (400nm-1100nm), …

Characteristics Of Hydrogel-Wetted Thin Films, James Owens

Electronic Theses and Dissertations

The meniscus region of a thin film is known to have high heat transfer properties due to high evaporation rates and activation of latent heat. The region known as the thin film meniscus (δfilm lt& 2 µm ) can account for more than half of the total heat transfer of a droplet or film. This study focuses on the potential elongation and curvature amplification of the thin film meniscus region by the implementation of a layer of high hydrogen bonding (hydrogel) film on which the liquid meniscus is built. Forced wetting via liquid propagation though this hydrogel layer in the …

Mid-Infrared Absorption Spectrometer For Multi-Species Detection Using Leds For Space Applications: Development And Flight Testing, Michael Villar

Electronic Theses and Dissertations

As commercial space travel expands, the need for specialized instrumentation to ensure the safety of crew and cargo becomes increasingly necessary. Both the Federal Aviation Administration (FAA) and pioneers in the space tourism industry have expressed an interest in a robust, low cost, and low power consumption sensor to measure atmospheric composition aboard spacecraft. To achieve this goal a time-resolved NDIR absorption sensor that measures transient levels of gaseous carbon dioxide (CO2) and carbon monoxide (CO) was developed. The developed sensor has a wide range of applications applicable to the growing needs of industry, from monitoring CO and CO2 levels …

Development Of A Flapping Wing Test Stand, Darnisha Crane

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

A Flexible Physics-Based Lifing Method For Metals Under Creep And Thermomechanical Fatigue, Firat Irmak

Electronic Theses and Dissertations

This thesis focuses on the development of a flexible, physics-based life prediction approach for steels under complex conditions. Low alloy steels continue to be the materials of choice for large turbomachinery structures experiencing high temperatures for long durations. There has been significant advancement in the research of modern alloys; furthermore, these materials are continue to be utilized in boilers, heat exchanger tubes, and throttle valve bodies in both turbomachinery and pressure-vessel/piping applications. The material 2.25Cr-1Mo is studied in the present work. The resistance of this alloy to deformation and damage under creep and/or fatigue at elevated temperatures make it appropriate …

Combustion Of 1,3-Butadiene Behind Reflected Shocks, Joseph Lopez

Electronic Theses and Dissertations

The chemical kinetics of 1,3-butadiene (1,3-C4H6) are important because 1,3-butadiene is a major intermediate during the combustion of real fuels. However, there is only limited information on the chemical kinetics of 1,3-butadiene combustion, which has applications in several combustion schemes that are currently being developed, including spark-assisted homogeneous charge compression ignition and fuel reformate exhaust gas recirculation. In the present work, the ignition delay times of 1,3-butadiene mixtures has been investigated using pressure data. Oxidation of 1,3-butadiene/oxygen mixtures diluted in argon or nitrogen at equivalence ratios (Φ) of 0.3 behind reflected shock waves has been studied at temperatures ranging from …

Simultaneous Imaging Of The Diatomic Carbon And Methylidyne Species Radicals For The Quantification Of The Fuel To Air Ratio From Low To High Pressure Combustion, Jonathan Reyes

Electronic Theses and Dissertations

The radical intensity ratio of the diatomic carbon to methylidyne was characterized at initial pressures up to 10 bar using certified gasoline of 93% octane. This gasoline was selected due to its availability as a common fuel. The characterization of the radical intensity ratio of gasoline at elevated pressures enabled the creation of a calibration map of the equivalence ratio at engine relevant conditions. The proposed calibration map acts as a feedback loop for a combustor. It allows for the location of local rich and lean zones. The local information acquired can be used as an optimization parameter for injection …

Data-Driven Adaptive Reynolds-Averaged Navier-Stokes K - Ω Models For Turbulent Flow-Field Simulations, Zhiyong Li

Theses and Dissertations--Mechanical and Aerospace Engineering

The data-driven adaptive algorithms are explored as a means of increasing the accuracy of Reynolds-averaged turbulence models. This dissertation presents two new data-driven adaptive computational models for simulating turbulent flow, where partial-but-incomplete measurement data is available. These models automatically adjust (i.e., adapts) the closure coefficients of the Reynolds-averaged Navier-Stokes (RANS) k-ω turbulence equations to improve agreement between the simulated flow and a set of prescribed measurement data.

The first approach is the data-driven adaptive RANS k-ω (D-DARK) model. It is validated with three canonical flow geometries: pipe flow, the backward-facing step, and flow around an airfoil. For all 3 test …

Modeling Of Flow Generated Sound In A Constricted Duct At Low Mach Number Flow, Peshala Thibbotuwawa Gamage

Electronic Theses and Dissertations

Modelling flow and acoustics in a constricted duct at low Mach numbers is important for investigating many physiological phenomena such as phonation, generation of arterial murmurs, and pulmonary conditions involving airway obstruction. The objective of this study is to validate computational fluid dynamics (CFD) and computational aero-acoustics (CAA) simulations in a constricted tube at low Mach numbers. Different turbulence models were employed to simulate the flow field. Models included Reynolds Average Navier-Stokes (RANS), Detached eddy simulation (DES) and Large eddy simulation (LES). The models were validated by comparing study results with laser doppler anemometry (LDA) velocity measurements. The comparison showed …

Summary Of "Supersonic Jet And Rocket Noise", Kent L. Gee, Caroline P. Lubert, Alan T. Wall, Seiji Tsutsumi

Department of Mathematics and Statistics - Faculty Scholarship

This paper summarizes a two-part special session, “Supersonic Jet and Rocket Noise,” which was held during the 174th Meeting of the Acoustical Society of America in New Orleans, Louisiana. The sessions were cosponsored by the Noise and Physical Acoustics Technical Committees and consisted of talks by government, academic, and industry researchers from institutions in the United States, Japan, France, and India. The sessions described analytical, computational, and experimental approaches to both fundamental and applied problems on model and full-scale jets and rocket exhaust plumes.