Architectural Engineering Commons^™

Addressing Low Heat Pump Heating System Sales In The Uk, Ben Costelloe

Articles

The replacement of existing fossil fuel boilers with heat pumps is seen as a key measure in the decarbonisation of heating systems and addressing climate change. This policy however, is currently failing in many Western European states, particularly in the UK. The many reasons for this situation are examined. However, the age of UK housing stock and particularly the high number of dwellings built prior to the introduction of building insulation regulations in 1980, are key. To maintain the running cost of air source heat pumps competitive with those of the gas boilers they generally replace the heat pump lift …

Sustainable Seismic Architecture: Exploring The Synergy Of Mortise-And-Tenon Joinery And Modern Timber Construction For Reducing Embodied Carbon, Cong Li

Masters Theses

Abstract

This design thesis explores the potential of combining ancient Mortise-and-Tenon joinery techniques with modern timber construction to create sustainable seismic architecture that simultaneously reduces embodied carbon. By studying the enduring qualities of Mortise-and-Tenon structures and their ability to withstand earthquakes, this research uncovers a synergistic relationship between traditional joinery methods and contemporary building materials, unlocking significant opportunities for embodied carbon reduction ranging from 7 to 40% compared to other modern architecture construction.

The research reveals that Mortise-and-Tenon structures commonly incorporate large roof systems, acting as mass dampers that provide flexibility and distribute weight evenly to columns. By transferring the …

Wast3d Potential, Andrew Larsen

Masters Theses

Waste is obsolete. Standard building industry practices are harmful to the environment. Non-traditional construction methods were examined as alternatives. Circular design logic was the guiding principle in material choice. Additive manufacturing is a proven modern method for building construction. Research on 3D printing case studies revealed that recycled plastic is a proven material and readily available. Removing plastic waste from the environment and sequestering it in architectural components gives the material a new purpose. The component of focus was a building block for a wall assembly. Inspiration was taken from the hexagonal Basalt rock formations found near volcanic fault lines. …

Sky Survey Radio Telescope, Jack E. Mcguigan

Electrical Engineering

This document outlines the design of a radio telescope designed to perform hydrogen line sky surveys. The telescope produces radio images mapping the intensity and relative velocities of hydrogen concentrations to their sky coordinates. Over the course of a day, the telescope images the regions of space visible to it, allowing sky survey imagery to be updated daily. Sky survey images are comprised of an array of pixels corresponding to specific sky coordinates. Each 8-bit RGB pixel contains information on the concentrations of hydrogen in the brightness and relative velocity in the color. Radio images mapping the concentrations and velocities …

Incentivizing Electric Vehicle Adoption Through State And Federal Policies: Reviewing Influential Policies, Joshua Sabata, Subhaditya Shom, Ahmad Almaghrebi, Anne Mccollister, Mahmoud Alahmad

Durham School of Architectural Engineering and Construction: Faculty Publications

All-electric vehicles (EVs), battery-powered EVs (BEVs), and plug-in hybrid EVs (PHEVS) are gaining market share and increasing in popularity with the buying public because the battery range (longer) and cost (lower) have reached sweet spots, the charging infrastructure is more robust, and concern with global cli­mate change is high. In 2013, only 100,000 EVs were sold in the United States, but by 2022, approximately 800,000 have been purchased. A similar growth is seen in EV sup­ply equipment (EVSE), i.e., EV charging stations, with 19,742 documented EV charging station locations in the United States in 2013 to 50,054 documented EV charging …

Concrete Masonry Program (Cmd21) Usability, Allie G. Decker

Architectural Engineering

The Concrete Masonry Design Program, CMD21, can be utilized in the design of beams, columns, and walls, but this project focuses on the use of the program to analyze shear walls loaded in-plane. This report critiques and describes the learning process behind the CMD21 program.

The Leaf For Leaning Pine Arboretum, Maria Boyle, Shelby Holmquist, Andrew Duong

Architectural Engineering

The goal of this ARCE 415 senior project course was to create a shade structure that could be incorporated into The Leaning Pine Arboretum, located on campus at Cal Poly, San Luis Obispo. From start to finish, these three ARCE students took on the role of form-finders to form-testers to form-makers. We are putting the "architectural" back in architectural engineering as we reclaim the historical tradition of the engineer as the form finder. In many of our design labs we focused primarily on sizing members and analysis, just using a structure that the architect already had established. In this one-of-a-kind …

Sustainability In Concrete Masonry With Natural Pozzolans, Ceiley L. Davis

Architectural Engineering: Graduate Reports

To achieve greater sustainability in masonry construction for the Western market it is common to replace masonry grout's partial cement content with waste pozzolans. As waste pozzolans are in limited supply, as the coal burning market in the West diminishes, this research investigates viable grout mixtures which replace cement with Natural Pozzolans, a more plentiful sustainable replacement. The present work investigated the percentage of Natural Pozzolans that can be partially substituted for cement for grout mixtures to achieve an axial compressive strength of 2000psi within 28 and 56 days of curing. To determine efficacy per ASTM 476-22, “Standards Specifications for …

Mbesese Build 2023, Ben Stewart, Matthew Chung, Ian Mcconnell

Architectural Engineering

In collaboration with the Mbesese Initiative for Sustainable Developments, the senior project group from California Polytechnic State University of San Luis Obispo, researched, designed, and created construction documents for the Same Polytechnic College project in the town of Same, Tanzania. This project aims to combat poverty in the Kilimanjaro Region of Tanzania by providing education and infrastructure development. In 2023, the senior project group focused on completing a communal and educational space and addressing clean water scarcity through a rainwater collection system on the site of the future college.

Crescent: Proposed Arboretum Shade Structure, Hayle Jones, Ian Kelly, Emilie Phuong, Brooke Heitman

Architectural Engineering

This is a sunshade structure that uses shells as the facade to create the enclosing of this structure.

Xenabloom, Sophia Maglabe, Ryer Lauth, Elizabeth Shaw, Sheyna Rongong

Architectural Engineering

Proposal for an architectural and structural design of a shade structure at the Leaning Pine Arboretum, employing the Xenaform typology of Poly Shells, LLC.

Investigation Of Natural Pozzolans: Analyzing The Practicality Of Natural Pozzolans As A Partial Substitute For Cement In Grout Production, Jadyn I. Breien, Andrew J. Baro, Logan T. Marino

Architectural Engineering

This senior project aims to investigate whether natural pozzolans are more sustainable than fly ash and a sufficient substitute for cement in the production of grout. By following the intent of the ASTM (American Society of Testing and Materials) standards, a conclusion will be made to determine if natural pozzolans can contribute comparable strength in compression. The objective is to prove that natural pozzolans should be utilized in the production of grout rather than alternatives such as fly ash because it can provide similar strength while being more economical and more sustainable.

Polymöbi: Single-Surface Timber Polyshell Shade Structure, Ryan Khieu, Tom Sesin, Gabriel Garfias, Evan Brooks

Architectural Engineering

Overall design process of incorporating Polyshells into a sunshade structure, while addressing client needs, materiality, constructability, and life safety.

Arce 415 Portfolio: The Green Bird Of Paradise, Kristofer R. Rickansrud, Ryan Chan, Brendan Peers, Joel Santoyo

Architectural Engineering

A design project creating a Polyshell sunshade structure for the Leaning Pine Arboretum.

The Center For Centering Dome, Olek Piechaczek, Ryan M. Scharf

Architectural Engineering

The Center for Centering seeks to create a large-scale healing center, conducive to individual centering of the mind and body. This mobile installation provides a relaxing, enclosed space while still maintaining a connection to the outdoors. The clients liked the idea of having a pop-up installation that could be easily set up as a touring display. With a deadline for installation looming in June 2022, a team of students had five months to design and manufacture the structure.

In winter 2022, the students developed custom geometry to minimize the number of individual parts and built a ¼ scale model of …

Physical And Digital Models For Timber Design And Analysis Courses, Paulina Robles, Gabrielle Rose Favro, Anahid Behrouzi, Abby Lentz

Architectural Engineering

Among structural engineering education research, there is a limited number of studies on interactive learning tools and activities specifically for the timber design classroom to assist students in visualizing material behavior, vertical and lateral load paths, and construction sequence. Timber design courses within the undergraduate program in the Architectural Engineering department at California Polytechnic State University in San Luis Obispo (Cal Poly), place an emphasis on seismic and wind design. Therefore, the proposed learning tools and activities are intended to pair with an introduction to concepts in the American Wood Council’s National Design Specifications (NDS) and Special Design Provisions for …

Automated Detection And Characterization Of Cracks On Concrete Using Laser Scanning, Yunfeng Ge, Jenny Liu, Xiong Zhang, Huiming Tang, Xiaolong Xia

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Accurate crack detection and characterization on concrete are essential for the maintenance, safety, and serviceability of various infrastructures. In this paper, an innovative approach was developed to automatically measure the cracks from 3D point clouds collected by a phase-shift terrestrial laser scanner (TLS) (FARO Focus3D S120). The approach integrates several techniques to characterize the cracks, which include the deviation on point normal determined using k-nearest neighbor (kNN) and principal components analysis (PCA) algorithms to identify the cracks, and principal axes and curve skeletons of cracks to determine the projected and real dimensions of cracks, respectively. The coordinate transformation was then …

Thermal And Energy Efficiency Of Roof Tiles Fabricated From Crushed Aluminum Slag And Kaolin Clay For Social Residential Buildings In Egypt, Mohamed E. Elattar

Architectural Engineering

No abstract provided.

Attainable And Sustainable Home Building Solutions, Katrina Matthews

Construction Management

Sustainability has fortunately been a recent concern in the construction industry as climate change continues to impose potentially insurmountable threats to the global environment. Although many new methods have been adopted in efforts to lessen the adverse environmental effects of construction-related activities, as a society, we still have much room for growth as the built environment accounts for almost 50% of global emissions. Many changes and standards must be adopted to make these solutions efficiently beneficial. To set industry standards, we must start with the most basic form of construction- residential building. This report covers two attainable framing solutions for …

Development Of The New Hasslein Caed Collaborative, Catie Dines

Construction Management

This paper outlines the development and execution of the new Hasslein CAED Collaborative student competition which engages students of all five majors in the College of Architecture and Environmental Design in a Request for Proposal style competition. CAED houses students studying Architecture, Architectural Engineering, City and Regional Planning, Construction Management, and Landscape Architecture. There is little opportunity for interdisciplinary collaboration within the CAED, despite our future career paths being heavily intertwined. This competition followed research by Greta Stout, class of 2022, on the benefits and support of interdisciplinary collaboration at Cal Poly SLO in CAED. The competition is named after …