Other Engineering Commons^™

Assessing The Economic Benefits Of Compressed Air Energy Storage For Mitigating Wind Curtailment, Brendan Cleary, Aidan Duffy, Alan O'Connor, Michael Conlon, Vasilis Fthenakis

Other resources

Renewable energy generation in the All-Island of Ireland (AII) is set to increase by 2020 due to binding renewable energy targets. To achieve these targets, there will be periods of time when 75% of electricity will be generated mainly from onshore wind. Currently, the AII system can accommodate a 50% maximum permissible instantaneous level of wind generation. The system operators must make system wide wind curtailment decisions to ensure this level is not breached. Subsequently, the ability to limit wind curtailment using large scale energy storage such as pumped hydroelectric energy storage and compressed air energy storage (CAES) is increasingly …

Evaluation Of Vibration Profiles For Uld Dollies At Air-Cargo Sorting Hubs, Jay Singh, Paul Singh, Koushik Saha

Journal of Applied Packaging Research

This study measured and analyzed the vibration characteristics of an important component of the air package shipping environment which has not been previously studied or included in the pre-shipment testing of packages. This is the movement of packages between aircraft after they are flown in to an airport-hub and being taken into a facility to conduct a sort, or after being sorted as they are transferred back on to aircraft. These transfers at airport-hubs between trucks, building sortation facilities and aircraft are done using material handling equipment called “dollies” or carts. These carts often are connected with each other into …

Ip Basics: Advice On Ip Careers For Those With Technical Backgrounds, Thomas G. Field Jr.

Law Faculty Scholarship

[Excerpt] Full-time law school takes three years and culminates in the Juris Doctor. A J.D. from a school accredited by the American Bar Association qualifies a person to take the bar exam in any state. As mentioned above, college graduates need not pursue any particular line of study to be accepted into law school. At the University of New Hampshire School of Law, for example, over a third of our students have degrees in engineering or science, and many have had extensive experience or advanced degrees, including M.D.s and Ph.Ds. -- the last being particularly helpful for biotechnology patent careers.

Using Photogrammetry To Document, Analyze, And Reverse-Engineer Grave Markers, Robert Z. Selden Jr.

CRHR: Archaeology

There are a wide range of applications for three-dimensional (3D) data in archaeology, and a diverse array of methods for collecting and analyzing those data. In this article, free 3D photogrammetry software (Autodesk 123D Catch) is used to document a series of grave markers. The data are subsequently exported to Geomagic Design X to demonstrate and briefly discuss the various potential analyses that might be used to illustrate the effects of preservation treatments and marker degradation through time. Further, one marker is reverse-engineered, illustrating the capacity of 3D modeling to expedite the process of design, should elements warrant replacement. Additional …

Comprehensive Understanding Of Nano-Sized Particle Separation Processes Using Nanoparticle Tracking Analysis, Desmond F. Lawler, Sungmin Youn, Tongren Zhu, Ijung Kim, Boris L.T. Lau

All Engineering Faculty Research

Understanding of nano-sized particle separation processes has been limited by difficulties of nanoparticle characterization. In this study, nanoparticle tracking analysis (NTA) was deployed to evaluate the absolute particle size distributions in laboratory scale flocculation and filtration experiments with silver nanoparticles. The results from NTA were consistent with standard theories of particle destabilization and transport. Direct observations of changes in absolute particle size distributions from NTA enhance both qualitative and quantitative understanding of particle separation processes of nano-sized particles.

The Evolution Of A New Technological University In Terms Of Policy Definition And Control Of Implementation, Kevin Kelly, Deborah Brennan

Conference papers

This paper derives from a Doctoral case study completed in the Dublin Institute of Technology (DIT) in 2008. The main issues of the case study are still being addressed today as DIT prepares to amalgamate with the Institute of Technology Blanchardstown (ITB) and Institute of Technology Tallaght (ITT) in 2015. The combined new institute will become a university in 2016 and is in the process of a move to a green field site. The rate and scope of these changes are challenging for all concerned. Through a series of interviews and focus groups in 2008, a story of DIT emerged. …

Engineering Ethics: Ontology And Politics, Eddie Conlon

Conference papers

“Ontology...acts as both gatekeeper and bouncer for methodology” (Archer 1995: 22). This exploratory paper, through a focus on the relationship between structure and agency, examines the underlying social ontologies informing the teaching, and researching of the teaching, of engineering ethics. It argues that current approaches are deficient and that Critical Realism can provide the basis for a more robust and inclusive research agenda for understanding engineering practice and the teaching of engineering ethics.

Exploring Programme Chairs' Understanding Of The Integration Of Sustainable Development: An Issue Of Professional Identity, Iacovos Nicolaou, Eddie Conlon, Brian Bowe

Conference papers

This paper is part of a wider study addressing the level of provision of sustainable development (SD) competencies in seven engineering programmes in three Irish Higher Education Institutions. The paper explores the influence that programme chairs’ professional identity has on their views of SD and their assessment of the extent to which SD is integrated in their programmes. The data for exploring this is taken from a thematic analysis of six interviews with programme chairs which shows that their assessments of the extent to which SD is integrated in their programmes are at odds with previous findings that highlight deficiencies …

The Epistemological Basis Of Engineering, And Its Reflection In The Modern Engineering Curriculum, Mike Murphy, William Grimson

Books/Book chapters

Perhaps unlike other professions, engineering is strangely difficult to define or describe. This is nowhere as evident as when an attempt is made to articulate its epis-temological basis. Engineering has a rich and complex ‘gene pool’ which goes back to when people first built shelters and shaped implements for agricultural purposes. Throughout the ages one constant characteristic of engineering has been its readiness to avail of whatever material is on hand together with whatever knowledge or skill is available to meet the challenge of enhancing an object or making something which nev-er previously existed. On occasion engineers have created new …

Air Change Rate Vs Airflow Pathway: Bioaerosol Containment And Removal In Patient Rooms, Kevin R. Grosskopf

Durham School of Architectural Engineering and Construction: Faculty Publications

Recent studies have shown that higher air change rates may have the unintended consequence of creating turbulent airflows that entrain high concentrations of infectious particles within the breathing zone, and possibly, breakdown pressure relationships necessary to contain the spread of infectious particles to other clinical spaces.

Chemical Storage Of Wind Energy By Renewable Methanol Production: Feasibility Analysis Using A Multi-Criteria Decision Matrix, Michael J. Matzen, Mahdi H. Alhajji, Yaşar Demirel

Department of Chemical and Biomolecular Engineering: Faculty Publications

This study is for the technoeconomic analysis of an integral facility consisting of wind energy-based electrolytic hydrogen production, bioethanol-based carbon dioxide capture and compression, and direct methanol synthesis. ASPEN Plus was used to simulate the facility producing 97.01 mt (metric tons) methanol/day using 138.37 mt CO₂/day and 18.56 mt H₂/day. A discounted cash flow diagram for the integral facility is used for the economic analysis at various hydrogen production costs and methanol selling prices. The feasibility analysis is based on a multi-criteria decision matrix consisting of economic and sustainability indicators comparing renewable and non-renewable methanol productions. …

Composite Tie Rod Research, Design And Testing For Sae Baja, Amanda M. Nauman

Williams Honors College, Honors Research Projects

Composite materials have become increasing popular in recent years. For the Baja SAE team, composites are typically only used for body panels. To grow as a team and to earn additional points in design competition, it was decided to explore composite use in mechanical applications, specifically for the tie rods. Research was conducted, looking into composite materials basics, types, and material properties. Additionally, manufacturing was explored, including a few projects separate from the tie rod application. 3D models were created after the materials were selected, and FEA analysis was conducted on the parts. Once theoretical testing was finished, the physical …

Engineering Identities: Section Introduction, Mike Murphy, Tony Marjoram

Books/Book chapters

No abstract provided.

Ventilation Rates And Airflow Pathways In Patient Rooms: A Case Study Of Bioaerosol Containment And Removal, Ehsan S. Mousavi, Kevin R. Grosskopf

Durham School of Architectural Engineering and Construction: Faculty Publications

Most studies on the transmission of infectious airborne disease have focused on patient room air changes per hour (ACH) and how ACH provides pathogen dilution and removal. The logical but mostly unproven premise is that greater air change rates reduce the concentration of infectious particles and thus, the probability of airborne disease transmission. Recently, a growing body of research suggests pathways between pathogenic source (patient) and control (exhaust) may be the dominant environmental factor. While increases in airborne disease transmission have been associated with ventilation rates below 2 ACH, comparatively less data are available to quantify the benefits of higher …

Adaptive Predictive Functional Controller, Fadi Alsaleem, Arvind Rao

Durham School of Architectural Engineering and Construction: Faculty Publications

A controller device and a method for controlling a system that utilizes an adaptive mechanism to self-learn the system char acteristics and incorporates this adaptive self-learning ability to predict a control parameter correctly to provide precise control of a system component.

An Adaptive Photovoltaic Topology To Overcome Shading Effect In Pv Systems, Mohamed Amer Chaaban, Lana El Chaar, Mahmoud Alahmad

Durham School of Architectural Engineering and Construction: Faculty Publications

Shading in photovoltaic systems can cause many undesired effects.When shading occurs, the power generated from the PV system is much less than nominal power, increasing the electrical mismatching losses between PV system components. Active research to address this power loss focuses on static and adaptive systems.This paper addresses an adaptive system solution and proposes a new method to adaptively overcome losses due to shading during low radiation conditions. In addition, a statistical analysis for choosing the most feasible and efficient configuration for the system size is presented. The proposed system has been validated under shade conditions in a simulation and …

Building Envelope And Interior Grading Systems And Methods, Fadi Mohammad Alsaleem

Durham School of Architectural Engineering and Construction: Faculty Publications

A difference module determines differences between an out door ambient temperature and an indoor temperature, deter mines a first average of the differences, and determines a second average of the differences. A storing module stores a first data point, the first data point including the first average and a first total run time of a heating, ventilation, and/or air conditioning (HVAC) system, and stores a second data point, the second data point including the second average and a second total run time of the HVAC system. A fitting module fits a line to the first and second data points. An …

Designing The Identities Of Engineers, Mike Murphy, Shannon Chance, Eddie Conlon

Books/Book chapters

Book Chapter forthcoming in Engineering Education and Practice in Context, Vol. 2 to be published by Springer in 2015.

A Critical Realist Approach To Engineering Ethics, Eddie Conlon

Conference papers

This paper is focused on the teaching of engineering ethics (EE). Through a focus on safety and the lens of what sociologists call the agency/ structure relationship it examimes various approaches to this teaching. Drawing on Critical Realism it argues there are deficiencies in both the dominant approach and a number of proposed alternatives as they suffer from various forms of conflationism . By drawing on Critical Realism (CR) a more robust agenda for teaching engineering ethics can be developed. It is argued that CR offers a basis for understanding the range of factors which lead to accidents and disasters. …

Dit-Topcon Internship Experience, Audrey Martin, Abigail Iversen

Articles

The Technological University Dublin (DIT: http://www.dit.ie/) is one of the largest Higher Education Institutes in Ireland, with 20,000 students registered and over 2000 members of staff. It has been providing technological higher education for over one hundred and twenty years encompassing the full spectrum of Third Level programmes. During that time the Institute's alumni have played important roles in technical and scientific innovation, economic and social development and culture and education both in Ireland and internationally.

The CEO of Topcon Positioning Systems Inc., Ray O’Connor is a DIT School of Surveying alumnus and in October 2013 Ray visited his …

An Architectural Perspective On Structured Sacred Space—Recent Evidence From Iron Age Ireland, Frank Prendergast

Book/Book Chapter

N/A

A Review Of Approaches For Sensing, Understanding, And Improving Occupancy-Related Energy-Use Behaviors In Commercial Buildings, Hamed Nabizadeh Rafsanjani, Changbum R. Ahn, Mahmoud Alahmad

Durham School of Architectural Engineering and Construction: Faculty Publications

Buildings currently account for 30–40 percent of total global energy consumption. In particular, commercial buildings are responsible for about 12 percent of global energy use and 21 percent of the United States’ energy use, and the energy demand of this sector continues to grow faster than other sectors. This increasing rate therefore raises a critical concern about improving the energy performance of commercial buildings. Recently, researchers have investigated ways in which understanding and improving occupants’ energy-consuming behaviors could function as a cost-effective approach to decreasing commercial buildings’ energy demands. The objective of this paper is to present a detailed, up-to-date …

Use Of Fiber-Reinforced Cements In Masonry Construction And Structural Rehabilitation, Ece Erdogmus

Durham School of Architectural Engineering and Construction: Faculty Publications

The use of fiber reinforcement in traditional concrete mixes has been extensively studied and has been slowly finding its regular use in practice. In contrast, opportunities for the use of fibers in masonry applications and structural rehabilitation projects (masonry and concrete structures) have not been as deeply investigated, where the base matrix may be a weaker cementitious mixture. This paper will summarize the findings of the author’s research over the past 10 years in these particular applications of fiber reinforced cements (FRC). For masonry, considering both mortar and mortar-unit bond characteristics, a 0.5% volume fraction of micro fibers in type …

A Comparison Of Combined Overlap Block Fuzzy Cognitive Maps (Cobfcm) And Combined Overlap Block Neutrosophic Cognitive Map (Cobncm) In Finding The Hidden Patterns And Indeterminacies In Psychological Causal Models: Case Study Of Adhd, Hojjatollah Farahani, Florentin Smarandache, Lihshing Leigh Wang

Branch Mathematics and Statistics Faculty and Staff Publications

In spite of researchers’ concerns to find causalities, reviewing the literature of psychological studies one may argue that the classical statistical methods applied in order to find causalities are unable to find uncertainty and indeterminacies of the relationships between concepts.

In this paper, we introduce two methods to find effective solutions by identifying “hidden” patterns in the patients’ cognitive maps. Combined Overlap Block Fuzzy Cognitive Map (COBFCM) and Combined Overlap Block Neutrosophic Map (COBNCM) are effective when the number of concepts can be grouped and are large in numbers. In the first section, we introduce COBFCM, COBNCM, their applications, and …

Engineering Faculty Perspectives On The Nature Of Quality Teaching, Jacqueline C. Mcneil, Matthew W. Ohland

Faculty and Staff Scholarship

There is wide agreement that teaching quality matters in higher education, but faculty have varied ideas about the definition of quality. Faculty definitions of quality teaching were coded using an existing framework. The most common definition of teaching quality (held by 49% of participants) is associated with elitism and restricted access—the best way to improve education is to admit better students. These faculty focus on education as “knowledge transfer” and “learning content.” Another 38% of faculty had a transformational perspective, more focused on process than content, valuing “empowering students,” “developing students,” and “creating an environment for learning.” These faculty refer …

Parametric Study Of Self-Centering Concentrically-Braced Frames In Response To Earthquakes, Nicholas F. Roth

Williams Honors College, Honors Research Projects

This research project consisted of the use of computer aided numerical software to test the response of an earthquake resistance system within various buildings when exposed to various design-level earthquakes. This research project is an extension of an existing NSF research project. The relevant questions and investigations of this and the greater project surround the performance of an earthquake resistance system with the intentions of better understanding its abilities and limitations. This project has been aided by Dr. David Roke, the faculty sponsor, in order to perform the research and collect, organize, and analyze the data. This research was performed …

The Simulation & Evaluation Of Surge Hazard Using A Response Surface Method In The New York Bight, Michael H. Bredesen

UNF Graduate Theses and Dissertations

Atmospheric features, such as tropical cyclones, act as a driving mechanism for many of the major hazards affecting coastal areas around the world. Accurate and efficient quantification of tropical cyclone surge hazard is essential to the development of resilient coastal communities, particularly given continued sea level trend concerns. Recent major tropical cyclones that have impacted the northeastern portion of the United States have resulted in devastating flooding in New York City, the most densely populated city in the US. As a part of national effort to re-evaluate coastal inundation hazards, the Federal Emergency Management Agency used the Joint Probability Method …

Cruise Ship Preliminary Design: The Influence Of Design Features On Profitability, Justin Epstein

LSU New Orleans Theses and Dissertations

This thesis provides a means to estimate the physical and performance characteristics of a preliminary cruise ship design. The techniques utilized to estimate these characteristics are showcased in the user-friendly interface known as the Cruise Ship Analysis Tool (CSAT). Using the CSAT, the implications that design feature decisions in the preliminary design stage have on a cruise ship’s profitability is analyzed. Then, the most profitable design feature assemblage among a finite number of varying design feature combinations is estimated and compared among cruise ship designs with different passenger carrying capacities. Profitability is analyzed using the measure of merit (MOM) known …

Computational Fluid Dynamics Analysis Of An Ideal Anguilliform Swimming Motion, Charles Rogers

LSU New Orleans Theses and Dissertations

There is an ongoing interest in analyzing the flow characteristics of swimming fish. Biology has resulted in some very efficient motions and formulating these motions is of interest to engineers. One such theory was written by Dr. William Vorus and Dr. Brandon Taravella involving ideal efficiency. It is therefore interesting to test the calculations to see if it is possible to design a motion that can create thrust without necessarily creating vorticity. The computational fluid dynamics software of ANSYS Fluent was used to calculate the resulting flow field of the eel motion to compare with the theoretical values.

Multifunctional Glazing System: Solution For Modern Smart Glazing, Aritra Ghosh, Brian Norton, Aidan Duffy

Conference papers

Multifunctional glazing combines various glazing ,that have potential to control solar heat gain by changing the window transmittance and low heat loss. In autonomous multifunctional glazing it s function will be powered by PV layer attached to the glazing. This glazing obviates the necessity for shading devices to control the glare. Glare control for such a small scale south facing vertical surface multifunctional glazing is discussed.