Other Engineering Commons^™

Exploring Red Palm Oil As A Sustainable Plasticizer For Carbon Black-Filled Ssbr/Br Tire Tread Compounds: A Comparative Evaluation Of Commercial Alternatives, Norma Arisanti Kinasih, Mohamad Irfan Fathurrohman, Santi Puspitasari, Dewi Kusuma Arti, Abdulhakim Masa

Journal of Materials Exploration and Findings

This study investigates the application of red palm oil (RPO) as an alternative vegetable oil resource to substitute petroleum-based plasticizers, which have environmental and health concerns, in carbon black (CB)-filled SSBR/BR tire tread compounds. The plasticizing effects of RPO were thoroughly evaluated by comparing them with a commercial bio-based plasticizer, Epoxidized Soybean Oil (ESBO), and two safer petroleum-based oils, Naphthenic Oil (NYNAS) and Treated Distillate Aromatic Extract (TDAE). The initial investigation shows that fatty acid composition is imposing regarding the plasticizing effect. The higher unsaturated fatty acid content in RPO than in ESBO improved tensile strength and degraded rolling resistance …

Techno-Economic Analysis Of The Utilization Of Waste-To-Energy In Jakarta Industrial Estate Pulogadung, Wahyu Punjung Pesonagrata, Mohammad Akita Indianto

Journal of Materials Exploration and Findings

Indonesia has a serious waste problem, which ranking second in marine pollution. Due to significant environmental impacts, a solution to overcome the complexity of waste problems is needed. This study took sample on waste management in Jakarta Industrial Estate Pulogadung (JIEP). JIEP is an Industrial area which covers 443 hectares of land in East Jakarta. This study aims to address Indonesia's serious waste problem by exploring the potential utilization of waste in the Jakarta Industrial Estate Pulogadung (JIEP) as Refuse-Derived Fuel (RDF) for a waste-to-energy (WtE) power plant. The proposed method used a steam power plant with RDF as fuel …

Metallurgical Investigation Of A Modified Eye Bolt Failure Caused By Improper Weld Extension, Specification Deviation, And Crevice Corrosion, Dimas Muhammad Fawwaz, Reza Miftahul Ulum, Johny Wahyuadi Soedarsono, Yudha Pratesa

Journal of Materials Exploration and Findings

A modified eye bolt from the David Arm Manhole Storage Tank underwent thorough metallurgical study due to the consequences of the bolt's malfunction during operation. Safety issues arose when the manhole door detached during operation. The mechanical testing and chemical composition analysis of the bolts indicated they were manufactured from an ASTM A193 Grade B7 material used for high-temperature bolting. This material did not conform to the engineering drawing, which mentioned SA 563A, which is about nuts, not bolts. This contradiction clearly shows that the eye bolt which was installed does not conform to the intended design. Welded connections of …

Rejection Of Fe (Iron) And Kmno4 (Organic Substance) Parameters In Peat Water Using Organic Membranes, Muhamad Rafli Sakti Mulia Gonera, Siti Umi Kalsum, Sarah Fiebrina Heraningsih

Journal of Materials Exploration and Findings

Peat water is a surface water source widely used by people in swampy and lowland areas, but it has poor quality characteristics such as high organic matter content, low pH, and dissolved metal levels such as iron that exceed the threshold. These conditions can cause health problems and reduce the quality of clean water so that effective treatment technology is needed. This study aims to analyze the effectiveness of ultrafiltration membranes made from chitosan from shrimp shell waste in rejecting iron (Fe) and organic substances in peat water, and to determine the effect of pressure on separation performance. This study …

Manufacturing Systems: Characteristics And Dynamics, Alan J. Fitzmorris

Graduate Theses and Dissertations (2019 - present)

This research answers three basic questions. First, what are the behaviors (dynamics) of a manufacturing system in the context of system performance? Are these dynamics best described as linear deterministic, periodic, nonlinear deterministic, or stochastic? Second, what are the complexity (chaotic) characteristics of a manufacturing system, namely the maximal Lyapunov exponent, correlation dimension, and Kolmogorov-Sinai entropy? Third, is there a relationship between complexity characteristics and manufacturing system performance? This research involves four high level steps: data analysis, system dynamics analysis, system complexity analysis, and correlation analysis. The data analyzed consists of concrete plant and shipbuilding shop time series performance data. …

Techno-Enviro-Economic Analysis Of Precipitated Calcium Carbonate Production From Carbon Dioxide In Cement Industry Flue Gas And Calcium Hydroxide, Natalia Debora Panggabean, Widodo Wahyu Purwanto

Journal of Materials Exploration and Findings

CCUS is a technological solution to reduce emissions from the cement industry, which is the second largest CO2-intensive industry. This study aims to analyze technical, economic, and environmental performance of Precipitated Calcium Carbonate (PCC) synthesis in cement industry flue gas. The process simulation includes the CO2 capture system from cement plant, CO2 captured used as feedstock for PCC synthesis process through its reaction with calcium hydroxide. The simulation was carried out using ASPEN Plus software. Technical analysis was performed to determine the CO2 capture efficiency and PCC synthesis efficiency. Economic analysis was conducted to calculate CO2 capture cost and production …

Feasibility Analysis Of Thermal Oxidizer To Determine Remaining Life Using Fitness- For-Service Level 3 Method, Yudhi Yudistirawan, Donanta Dhaneswara, Wahyuaji Narottama Putra, Gama Widyaputra, Dewi Kurnia Suci, Agung Putra Mahardhika

Journal of Materials Exploration and Findings

An aged thermal oxidizer (TOX) in the oil and gas industry necessitates a comprehensive evaluation to ensure its continued safe operation. This study presents a Remaining Life Assessment (RLA) and a Fitness for Service (FFS) evaluation for the four main components of the TOX, in accordance with API 510, API 579/ASME FFS-1, and ASME BPVC Section VIII Div-1 standards. The investigation includes the determination of maximum stress and maximum temperature required to assess the operational viability of the reactor. The four components are radiant, convection, transition, and stack sections—were modeled using the finite element method (FEM). Following the geometric modeling, …

Risk Identification Of Green Hydrogen Supply Chain In Ammonia Industry In Indonesia Using Delphi And Topsis Methods, Ananda Priatama, Sheila Tobing

Journal of Materials Exploration and Findings

The development of green hydrogen in Indonesia, while promising for supporting industrial decarbonization, remains in its early stages and faces various challenges across technical, economic, and regulatory domains. This study aims to identify and prioritize the risks linked to green hydrogen supply chain in Indonesia, particularly for applications in the ammonia industry. A set of 49 potential risk factors was initially compiled through literature review and prior studies. The Delphi method was employed with a panel of experts to validate these risks, ultimately refining the list to 27 critical risk factors. Subsequently, the Technique for Order Preference by Similarity to …

Assessing Passenger Electric Vehicle Growth Strategies And Their Impacts On Electricity Demand Load And Co2 Emissions In Aceh Province To Achieve Net Zero Emission Target By 2060, Taufik Hidayat, Widodo Wahyu Purwanto

Journal of Materials Exploration and Findings

The electrification of the transport sector is a crucial pathway for achieving Indonesia’s Net Zero Emissions (NZE) target by 2060. This study assesses the potential impact of passenger electric vehicle (EV) penetration on electricity demand and CO2 emissions in Aceh Province through a scenario-based modelling approach. Two policy-aligned scenarios are assessed: a low-penetration (LP) scenario and a high-penetration (HP) scenario. Using the Gompertz model and the ASIF framework, total CO2 emissions were projected from 2020 to 2060. Results show that although higher EV penetration reduces direct emissions from internal combustion engine (ICE) vehicles, total CO2 emissions increase more significantly under …

Cavitation-Aware Design Of Hydrofoil Sections For Marine Propeller Blade Development, Samuel G. Bacon

Mechanical & Aerospace Engineering Theses & Dissertations

Cavitation is a major design constraint for marine propeller blade sections because it can reduce hydrodynamic performance, increase vibration and noise, and contribute to surface damage. This thesis develops and applies an exploratory computational framework for cavitation-aware hydrofoil-section design relevant to marine propeller blade development. The framework combines section-level CFD validation, CST-based geometry parameterization, pressure-based pre-screening, matched-load comparison, and focused predicted inception envelope or cavitation-bucket analysis.

The CFD methodology was validated against published YS-920 hydrofoil water-tunnel data using selected fully wetted, near-inception, and cavitating reference cases. The validation results showed that the adopted framework reproduced the key experimental trends needed …

Deep Learning Based Control System For Multi-Zone Hvac Residential Buildings, Mohammad H. Z. Alghalayeeni

Mechanical Engineering Theses

Heating, ventilation, and air conditioning (HVAC) systems are major contributors to residential energy consumption. However, most homes continue to rely on single zone thermostat control, which regulates temperature based on a single sensor and cannot account for thermal variations across multiple rooms. This often leads to uneven thermal conditions and inefficient energy use in multi-zone residential buildings. This thesis presents a deep reinforcement learning based approach for improving HVAC zoning control through dynamic airflow distribution. A physics based multi zone thermal model of a residential house was developed to simulate heat transfer processes including conduction, convection, solar and internal heat …

Automation And Habitat Development For A Space Based Marine Life Environment, Logan Trimmer, Alexander Hang

Harrisburg University Other Works

This project was a cross-collaboration between the Environmental Sciences and Advanced Manufacturing and Robotics programs for the company Monolith Space.

The goal of this project was to design an autonomous system to be able to track qualities of water in an aquaculture system designed to be sent to space.

Ai-Based Porosity Detection In Babbitt Bore Turning, Kaylee Leggett, Hannah Adams Gemmell, Kaisa Shingleton

Williams Honors College, Honors Research Projects

For this project, an external company reached out to the University of Akron requesting assistance with defect detection during their vertical turning operations. As babbitt is removed in a vertical turning process, it occasionally reveals defects, mainly porosity, which can lead to costly downstream failures of the part. Current inspection techniques involve use of dye penetrant, which is time consuming, labor intensive, unergonomic, and a source of human error. The goal of the project is to create an alternative inspection method using an AI-based machine-learning model. After the turning operation, a camera is deployed to perform an in-place inspection, taking …

Analysis Of Leakage In Nearshore Pipelines Using Fitness For Service Method To Ensure Mechanical Integrity Based On Api-579 Level 3, Elriandri Elriandri, Dedi Priadi

Journal of Materials Exploration and Findings

The Fitness for Service (FFS) analysis is performed as a quantitative assessment to evaluate the integrity condition of a pipeline. Essentially, FFS assessment helps determine whether equipment components can operate safely despite existing deficiencies. This evaluation is carried out using the Finite Element Method (FEM). In the case of an underwater pipeline that experiences leak due to anchor pull at the flange connection, it undergoes plastic deformation and is lifted approximately 1 meter. As a mitigation step, inspection and repairs have been carried out by the company. Subsequently, modeling is performed to reconstruct the deformation process of the pipeline. Then, …

Assessment Of The Melt Quality Of A 30% Scrap Adc12 Aluminium Alloy Using The Inclusion And Fluidity Measurement Instrument (Ifmi) With Mullite Ceramic Filters, Gusti Ruri Ruri Lestari, Sandya Ananda Riswan, Muhammad Anis, Ahmad Ashari, Paramita Vidya Ayuningtyas, Bambang Suharno Prof, Donanta Dhaneswara

Journal of Materials Exploration and Findings

The increasing demand for sustainable practices in the metal casting industry has driven the use of recycled aluminum alloys such as ADC12. However, the addition of aluminum scrap tends to increase oxide inclusions, which reduce melt fluidity and compromise casting quality. This study utilizes the Inclusion and Fluidity Measurement Instrument (IFMI), equipped with mullite ceramic filters, to assess the melt quality of ADC12 aluminum alloy containing 30% scrap. Fluidity and inclusion characteristics were evaluated at five pouring temperatures (660°C, 680°C, 700°C, 720°C, and 740°C). The results show that fluidity increased with temperature, reaching a peak of 84.6 g·s⁻¹ at 740°C, …

Equipment Criticality Analysis To Determine Asset Integrity Management System Scheme In Supporting Production Optimization Scenarios In The Aeging Field, Donny Andryanto, Donanta Dhaneswara

Journal of Materials Exploration and Findings

This research investigates the production decline and cost increase in the X&Y oil and gas fields from 2022 to 2023. Production fell by 34%, while production costs per barrel rose by 79%. To address these issues, a series of optimization processes are proposed. These aim to restructure and enhance the production facilities to reduce current production costs. The optimizations include reducing pressure at the PPP Platform in 2024. Additional steps include shutting down CPP-ORF 14” pipelines and most processes at CPP 2 Platform by 2027 to convert it into an accommodation platform. Further, the plan involves optimizing the release of …

An Overview Of Biomass-Derived Graphene Oxide And Its Characteristics For Future Sustainable Applications, Afif Wardana, Ahmad Nabil Shahab, Donanta Dhaneswara, Nofrijon Sofyan

Journal of Materials Exploration and Findings

The production of graphene oxide (GO) from biomass presents considerable promise as a sustainable alternative substitute for traditional semiconductors. Biomass waste, abundant and often underutilized worldwide, is distinguished by its high carbon content and regenerative characteristics, rendering it an optimal resource for sustainable material production. By heating its biopolymers, lignocellulosic biomass can be used as a new material to make graphene, which forms three-dimensional turbostratic crystallites. These crystallites, composed of partially defective aromatic carbon sheets with graphite-like characteristics, make it easier to create GO with specialized functions for cutting-edge applications. Its capability underscores the revolutionary potential of biomass waste in …

Morphological Test Of Areca Nut Fiber Ceramic Membrane Using Scanning Electron Microscopy Energy Dispersive X-Ray Mapping Spectroscopy, Amelia Marzain, Siti Umi Kalsum, Marhadi Marhadi, Ahmad Nabil Shahab

Journal of Materials Exploration and Findings

This study investigates the potential of ceramic membranes derived from areca nut fiber as a cost-effective and environmentally sustainable material for the removal of iron (Fe) and manganese (Mn) from groundwater. Two types of membranes were fabricated: one without activation and one chemically activated using 10% sodium hydroxide (NaOH). The morphological and elemental characteristics of both membranes were analyzed using Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray (EDX) mapping. The concentrations of Fe and Mn before and after treatment were measured using Atomic Absorption Spectroscopy (AAS). The NaOH-activated membrane exhibited a more porous surface structure and higher oxygen content, …

Experiential Learning And The Revitalization Of Manufacturing Education At The University Of Dayton, Sean Cahill

Research and Reflection on Learning and Teaching in Higher Education

This perspective paper explores the role of experiential learning in preparing future-ready manufacturing engineers at the University of Dayton, set against the backdrop of Dayton’s legacy as an industrial innovator and the broader national movement to revitalize domestic manufacturing. As automation, cyber-physical systems, and Industry 4.0 technologies reshape the manufacturing landscape, there is a growing need for engineers who possess both technical fluency and systems-thinking capabilities. To meet this need, the manufacturing engineering technology department implemented hands-on, integrated lab-and-lecture modules through support from the Experiential Learning Innovation Fund for Faculty (ELIFF). Grounded in Kolb’s Experiential Learning Theory and constructivist learning …

User Interface And Watchstation Improvements Required For Multi-Vehicle Usv Operations, Val Schmidt, Joshua Bergeron

Faculty Publications

In October 2024, the University of New Hampshire and NOAA’s Uncrewed Systems Office embarked on a mapping mission in the Gulf of Maine, simultaneously operating two DriX Un-crewed Surface Vehicles. Goals of the project were focused on testing hypotheses related to concepts of operation, including the safety of operations, cognitive loading of operators, management of vehicle endurance, vehicle logistics, maintenance and field support, refueling and a host of others.

A Study Of Wear Measurement And Life Prediction Of Insert Chute Liner On Gold Ore Processing, Ferry Ardika Natanael, Nony Maulidya, Dedi Priadi

Journal of Materials Exploration and Findings

Chutes are critical materials handling assets to transport solid particles from one process step to another in mineral processing, coal mining and cement industries. The material transport, because of material characteristics, cause severe wear on internal lining of chutes or bins’ structure. The wear problem on internal lining of bins or chutes needs to be checked to keep production efficiency. Therefore, not checked wear rate causes liner replacement schedule becomes unpredictable. It leads to production loss and highly cost maintenance in industry. This study shows that condition-based maintenance through regular thickness measurement using Ultrasonic Transducer (UT) to predict life service …

Correlation Between Microstructure And Hardfacing Properties With Welding Current Intensity In Reconditioned Low-Alloy Steel Material Using Submerged Arc Welding (Saw) : A Comprehensive Review, Iman Nugraha Asmara, Winarto Winarto

Journal of Materials Exploration and Findings

This review studying the correlation between microstructural transformations and mechanical properties in reconditioned low-allow steel material, focusing on the impact of Submerged Arc Welding (SAW) parameters, especially current, on microstructure . The study highlights how variation on welding parameters, especially current intensity variation, affecting microstructural transformations, hardness, and wear resistance of hardfaced layers. Key aspects such as dilution effect, phases distribution, and carbide formation are reviewed to understanding their impact on mechanical properties. By reviewing insights from existing literature and experimental findings, this review underscores the role of Submerged Arc Welding in enhancing mechanical properties and microstructural of low-alloy steel …

Techno-Enviro-Economic Approach For Electrification Of Rural And Shrimp Farming Regional Development Of An Isolated Island In Indonesia By Utilizing Hybrid Renewable Energy Systems, Fiqih Akbar Wijaya, Mohammad Akita Indianto

Journal of Materials Exploration and Findings

One of the challenges in developing and archipelagic countries such as Indonesia is maintaining energy demand in rural and isolated areas due to difficulties in electrical distribution. For instance, in areas like Bawean Island, no additional electricity capacity has been introduced in the past year, leading to an unmet potential customer demand. One of the possible options is by utilizing Hybrid Renewable Energy Systems (HRES) that are integrated with existing fossil fuel-based energy systems to support the growing energy demand in the remote island. A case study in Bawean Island is conducted with the projected energy demand covers the energy …

Remaining Life Assessment And Fitness For Service Evaluation Of Aging Chemical Reactors In Polyethylene Terephthalate Resin Industry, Aditya Pahlawan Munthe, Donanta Dhaneswara, Wahyuaji Narottama Putra, Gama Widyaputra

Journal of Materials Exploration and Findings

Aging chemical reactors in the polyethylene terephthalate (PET) resin industry require comprehensive evaluation to ensure safe continued operation. This study conducts a remaining life assessment (RLA) and fitness-for-service (FFS) evaluation on five 30-year-old reactors, based on API 510, API 579/ASME FFS-1, and ASME BPVC Section VIII Div. 1 standards. The analysis involves corrosion rate measurement, future corrosion allowance (FCA) projection, and minimum thickness verification. Among the reactors, R-120 was found to have the shortest remaining life less than 15 years. FFS assessments using three criteria Average Measured Thickness, MAWP from Point Thickness Readings, and Minimum Measured Thickness confirm that R-120 …

Analysis Of Leak Testing Planning For Carbon Dioxide Piping Systems In The Development Of Carbon Capture, Utilization, And Storage Facilities In The Bintuni Basin, Devi Sentiani, Akhmad Herman Yuwono Professor

Journal of Materials Exploration and Findings

Carbon Capture, Utilization, and Storage (CCUS) technologies have become a key strategic response to global efforts to reduce CO₂ emissions. This study presents a leak testing strategy designed for a carbon dioxide (CO₂) piping system as part of a Carbon Capture, Utilization, and Storage (CCUS) project in the Bintuni Basin, West Papua, Indonesia. This study aims to ensure the system is properly prepared before commissioning by designing a leak test plan that is both practical and technical, based on ASME B31.3, ASME PCC-2, and API STD 520 Part 1. We conducted the process, which involves identifying the system boundaries, …

Enhanced Point Cloud Generation From A Novel 360° Underwater Lidar, Olagoke E. Daramola

Dissertations

This dissertation presents novel algorithms to improve the mapping capabilities of a 360-degree underwater Pulsed Laser Line Scanner LiDAR (PLLS-360°). Due to its 360° field-of-view (FOV), the PLLS-360° is a compact full-waveform omnidirectional imager suitable for seafloor mapping, underwater asset inspection, object detection, ice-sheet mapping, and construction progress monitoring. The proposed methodology includes an improved waveform fitting technique for saturated waveform recovery, detection array response correction, radiometric corrections, and fusion of LiDAR and sonar bathymetric datasets. The first part of this dissertation assesses the LiDAR’s performance and describes how the data for this unique 360° FOV architecture is processed. The …

From Concept To Light: Manufacturing A Dual-Purpose Bedside Lamp And Book Organizer, Nicole Goulet

Honors Theses

This report features the design, development, engineering changes, and manufacturing of the Bedside Lamp, a hand-made multi-purpose lamp, book holder, and charging hub. The investigation began with research and a market analysis on current lamp designs and a discussion about what features would set the lamp apart. This led to the design of the lamp and construction of multiple prototypes for proof of concept.

A manufacturing process was then designed to demonstrate the steps to start up an efficient and cost-effective production line. This process included obtaining raw materials, cutting them into the necessary parts, and assembling everything to create …

Using Scaffolding, Gamification, And Self Awareness To Create Responsive Ux/Ui In Cad Software To Nurture Metacognition In Novice Users, Obed Ibrahim Gonzalez

Graduate Theses and Dissertations

Computer-aided Design (CAD) software represents a significant shift from manual and analog design processes to digital workflows, offering substantial utility, accuracy, and productivity benefits. However, CAD software often presents a steep learning curve, particularly for novice users who are new to the software or possess only basic knowledge. Traditional CAD curricula have predominantly focused on technical problem-solving—teaching tools and systems—while often neglecting strategic knowledge that encompasses reflection, planning, and refining, which are essential components of metacognition. Metacognition is crucial for transforming novices into experts who use fewer and more complex commands, employ sophisticated planning, and achieve their goals more efficiently. …

Integrity Assessment Of Shipping Line Pipelines Using Risk-Based Analysis To Determine Risk And Maintenance Strategies, Ade Ratih Anggraini, Dwi Marta Nurjaya

Journal of Materials Exploration and Findings

Pipeline Shipping Lines X, Y & Z are classified as critical infrastructure, being the only transportation through the crude oil lifting from P and R location to the transfer station in NM Area. To maintain the workflow of the Shipping Line, integrity assessments and risk evaluation are required to ensure the operational and safety. Anomalies were found by analysing inspection, monitoring, and repair data, while the pipelines' future integrity was assessed by calculating the remaining life. Risk-Based Analysis (RBA), which is a modification of Kent Muhlbaeur's method, is employed to conduct the risk assessment using the Probability of Failure (POF) …

Assessment Of H2s-Induced Cracking Susceptibility In Steam Line Pipes And Weld Zones During Geothermal Well Construction, Riene Kaelamanda Pragitta, Yudha Pratesa

Journal of Materials Exploration and Findings

The susceptibility of steam line pipes, especially in the HAZ (heat-affected zone) and weldment areas, to hydrogen sulfide in the geothermal industry is crucial to understand from the early stages, particularly during construction. The combination of tensile stress from residual stresses after welding and metallurgical phase transformation makes the joint areas vulnerable to sulfide stress cracking. This condition becomes even more extreme when the equipment operates during the well stimulation phase. This research assesses the severity of H₂S-induced cracking using NACE MR0175 and ISO 15156-1 standards, focusing on the effects of pH and partial pressure of H₂S (p_{H₂S …}