Open Access. Powered by Scholars. Published by Universities.®

Manufacturing Commons™

Open Access. Powered by Scholars. Published by Universities.®

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Articles 91 - 120 of 209

Full-Text Articles in Manufacturing

Effect Of Sparse-Build Internal Structure On Performance Of Fused Deposition Modeling Tools Under Pressure, S. Meng, L. Mason, Gregory Taylor, X. Wang, Ming-Chuan Leu, K. Chandrashekhara, Mike Matlack, James Castle Aug 2016

Effect Of Sparse-Build Internal Structure On Performance Of Fused Deposition Modeling Tools Under Pressure, S. Meng, L. Mason, Gregory Taylor, X. Wang, Ming-Chuan Leu, K. Chandrashekhara, Mike Matlack, James Castle

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Two different approaches to design a sparse-build tool for fabrication by the fused deposition modeling (FDM) process are compared. One approach uses a 2D lattice structure and the other approach is inspired by topology optimization. Ultem 9085 is used as the material, and the amount of material used to build the tool is kept constant to ensure a fair comparison. A solid tool is also included in the comparison. The performance of the tool under uniform pressure is simulated using finite element analysis (FEA) and the accuracy of the FEA results is verified by comparing them with experimentally measured data …

Go to article

Novel Extrusion-Based Additive Manufacturing Process For Ceramic Parts, Amir Ghazanfari, Wenbin Li, Ming-Chuan Leu, Greg Hilmas Aug 2016

Novel Extrusion-Based Additive Manufacturing Process For Ceramic Parts, Amir Ghazanfari, Wenbin Li, Ming-Chuan Leu, Greg Hilmas

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An extrusion-based additive manufacturing process, called the Ceramic On-Demand Extrusion (CODE) process, for producing three-dimensional ceramic components with near theoretical density is introduced in this paper. In this process, an aqueous paste of ceramic particles with a very low binder content (< 1 vol%) is extruded through a moving nozzle at room temperature. After a layer is deposited, it is surrounded by oil (to a level just below the top surface of most recent layer) to preclude non-uniform evaporation from the sides. Infrared radiation is then used to partially, and uniformly, dry the just-deposited layer so that the yield stress of the paste increases and the part maintains its shape. The same procedure is repeated for every layer until part fabrication is completed. Several sample parts for various applications were produced using this process and their properties were obtained. The results indicate that the proposed method enables fabrication of large, dense ceramic parts with complex geometries.

Go to article

Modal Response As A Validation Technique For Metal Parts Fabricated With Selective Laser Melting, Joshua D. Pribe, Brian M. West, Michelle L. Gegel, Troy Hartwig, Toby Lunn, Ben Brown, Douglas A. Bristow, Robert G. Landers, Edward C. Kinzel Aug 2016

Modal Response As A Validation Technique For Metal Parts Fabricated With Selective Laser Melting, Joshua D. Pribe, Brian M. West, Michelle L. Gegel, Troy Hartwig, Toby Lunn, Ben Brown, Douglas A. Bristow, Robert G. Landers, Edward C. Kinzel

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper investigates modal analysis as a validation technique for additively manufactured parts. The Frequency Response Function (FRF) is dependent on both the geometry and the material properties of the part as well as the presence of any defects. This allows the FRF to serve as a “fingerprint” for a given part of given quality. Once established, the FRF can be used to qualify subsequently printed parts. This approach is particularly attractive for metal parts, due to the lower damping as well as use in high-value applications where failure is unacceptable. To evaluate the efficacy of the technique, tensile specimens …

Go to article

Designed Extrudate For Additive Manufacturing Of Zirconium Diboride By Ceramic On-Demand Extrusion, Devin Mcmillen, Wenbin Li, Ming-Chuan Leu, Greg Hilmas, Jeremy Lee Watts Aug 2016

Designed Extrudate For Additive Manufacturing Of Zirconium Diboride By Ceramic On-Demand Extrusion, Devin Mcmillen, Wenbin Li, Ming-Chuan Leu, Greg Hilmas, Jeremy Lee Watts

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This work describes a process by which zirconium diboride (ZrB2) parts may be fabricated using the Ceramic On-Demand Extrusion (CODE) process. An oxide-carbide-nitride system consisting of ceramic powders and pre-ceramic organics, designed to yield ZrB2 after reaction sintering, has been developed to produce an aqueous-based extrudate for subsequent processing in the CODE system. Pressurelessly sintered test specimens containing 1 wt% PVA binder achieve high relative density ≥ 99%. The viscoelastic response of the extrudate was characterized via spindle rheometry with a small sample adapter. Batches with 1 wt% PVA and 0.5 wt% Methocel show strong shear thinning characteristic, under …

Go to article

Effects Of Build Parameters On Compression Properties For Ultem 9085 Parts By Fused Deposition Modeling, Krishna P. Motaparti, Gregory Taylor, Ming-Chuan Leu, K. Chandrashekhara, James Castle, Mike Matlack Aug 2016

Effects Of Build Parameters On Compression Properties For Ultem 9085 Parts By Fused Deposition Modeling, Krishna P. Motaparti, Gregory Taylor, Ming-Chuan Leu, K. Chandrashekhara, James Castle, Mike Matlack

Mechanical and Aerospace Engineering Faculty Research & Creative Works

It has been observed by various researchers that parts fabricated by the Fused Deposition Modeling (FDM) process have anisotropic properties. The research presented in the present paper was aimed to study the compression properties of FDM parts and to comprehend their dependence on build parameters. In this study Ultem 9085 was used as the material to fabricate both solid and sparse-build coupons with variations in build direction, raster angle and air gap. A full factorial experimental design was used to study the individual and combined effects of these build parameters on the mechanical properties of the coupons. The mechanical properties …

Go to article

Proposed Hybrid Processes For Part Building Using Fusion Welding And Friction Stir Processing, Megan A. Gegesky, Frank W. Liou, Joseph William Newkirk Aug 2016

Proposed Hybrid Processes For Part Building Using Fusion Welding And Friction Stir Processing, Megan A. Gegesky, Frank W. Liou, Joseph William Newkirk

Mechanical and Aerospace Engineering Faculty Research & Creative Works

It has been shown that a hybrid laser additive manufacturing and friction stir processing can deposit components with forged-like structures. This paper reports a hybrid fusion welding and friction stir process to create parts with quality structures. Combining traditional fusion welding and friction stir processing techniques for non-weldable aluminum alloys could facilitate the joining of difficult geometries in manufactured parts. This research illustrates mechanical property changes for non-weldable and weldable aluminum alloys. The Vickers hardness, and microhardness in the case of AA5052-H32, tensile strength and corrosion resistance of four processing states: base material, fusion welded material, friction stir welded material, …

Go to article

Microstructure And Property Of Tib-Reinforced Ti Alloy Composites By Laser Metal Deposition, Yunlu Zhang, Jingwei Zhang, Frank W. Liou, Joseph William Newkirk Aug 2015

Microstructure And Property Of Tib-Reinforced Ti Alloy Composites By Laser Metal Deposition, Yunlu Zhang, Jingwei Zhang, Frank W. Liou, Joseph William Newkirk

Mechanical and Aerospace Engineering Faculty Research & Creative Works

TiB-reinforced Ti alloy composites have been laser deposited with pre-alloyed Ti-6Al4V-1B powder. The microstructure of the as-deposited and heat treated composites have been characterized in detail using scanning electron microscope (SEM). A homogeneous dispersion of needle-like TiB precipitates is formed in the Ti-6Al-4V α/β matrix. TiB precipitates promote formation of small near equaxed α/β grain after β annealing process. The micro-hardness of the laser deposited composites increase 20-30% with 5 vol. % TiB precipitates compared to unreinforced Ti-6Al-4V deposits.

Go to article

Effects Of Temperature On Aqueous Freeform Extrusion Fabrication, Jie Li, Ming-Chuan Leu, Greg Hilmas Aug 2015

Effects Of Temperature On Aqueous Freeform Extrusion Fabrication, Jie Li, Ming-Chuan Leu, Greg Hilmas

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An experimental study was conducted to investigate the effect of temperature on ceramic parts produced by paste extrusion based additive manufacturing followed by sintering. A computer-controlled gantry system equipped with a piston extruder was used to extrude aqueous alumina paste. The system includes a temperature control subsystem that allows for freeform extrusion fabrication inside a low-temperature (<0°C) chamber. It can also be used for fabricating parts on a hot plate at ambient or higher temperatures (≥20°C). Test specimens were fabricated from aqueous aluminum pastes at -20°C in the low-temperature chamber and also on the hot plate at 40°C. The minimum angles achievable by these two processes for part fabrication, without use of support material, were compared. Also compared were the relative density and mechanical properties of the parts obtained after sintering. Microstructures were examined via scanning electron microscopy in order to obtain a deeper understanding of the effect of fabrication temperature.

Go to article

Laser Metal Deposition Of Functionally Gradient Materials From Elemental Copper And Nickel Powders, Sreekar Karnati, Todd E. Sparks, Frank W. Liou, Joseph William Newkirk, Karen M. Brown Taminger, William J. Seufzer Aug 2015

Laser Metal Deposition Of Functionally Gradient Materials From Elemental Copper And Nickel Powders, Sreekar Karnati, Todd E. Sparks, Frank W. Liou, Joseph William Newkirk, Karen M. Brown Taminger, William J. Seufzer

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This work deals with the planning and fabrication of a functionally gradient copper-nickel composition via Laser Metal Deposition (LMD). Various compositions of copper and nickel were made by blending different weight percentages which were then sequentially deposited to fabricate functionally gradient copper-nickel thin-wall structures. Analyses were performed by sectioning the thin-wall samples for metallographic, hardness, X-ray diffraction (XRD) and Energy Dispersive X-ray Spectroscopy (EDS) studies. The fabrication was studied for identifying and corroborating the deposited compositions and their corresponding gradients. XRD analyses were performed to identify the crystal structure of the deposit. EDS analysis was instrumental in identifying the variation …

Go to article

Parameter Determination And Experimental Validation Of A Wire Feed Additive Manufacturing Model, Kannan Suresh Kumar, Todd E. Sparks, Frank W. Liou Aug 2015

Parameter Determination And Experimental Validation Of A Wire Feed Additive Manufacturing Model, Kannan Suresh Kumar, Todd E. Sparks, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Laser metal deposition with wire feed is one of the additive manufacturing methods with great scope and robustness. Process parameters plays an important role in controlling the process and obtaining an ideal manufactured part. Simulations tools are highly essential in determining the ideal parameters and melt pool conditions. The current work is a transient 3D model of wire feed additive manufacturing which realizes the heat transfer and fluid flow behavior of the process with varying laser power and power density. The model was programmed in Python and a 1 KW Gaussian beam fiber laser was used to conduct experiments. The …

Go to article

Optimal Rastering Orientation In Freeform Extrusion Fabrication Processes, Amir Ghazanfari, Wenbin Li, Ming-Chuan Leu, Robert G. Landers Aug 2015

Optimal Rastering Orientation In Freeform Extrusion Fabrication Processes, Amir Ghazanfari, Wenbin Li, Ming-Chuan Leu, Robert G. Landers

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Many researchers have tried to optimize the build direction of additively manufactured parts to minimize the vertical staircase effect. However, the horizontal staircase effect should also be considered when fully dense parts are to be fabricated. In this paper, part inaccuracy due to the horizontal staircase effect is considered in order to determine the optimal rastering orientation in building the part. An algorithm is developed to estimate this inaccuracy and a technique is proposed to minimize it. The effect of rastering orientation on staircase errors is examined, and the particle swarm optimization method is used to determine the optimum rastering …

Go to article

Performance Metric For Powder Feeder Systems In Additive Manufacturing, Venkata Sivaram Bitragunta, Todd E. Sparks, Frank W. Liou Aug 2015

Performance Metric For Powder Feeder Systems In Additive Manufacturing, Venkata Sivaram Bitragunta, Todd E. Sparks, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In blown powder Direct Metal Deposition (DMD) process, parts are built by adding metal powder on the melt pool created by the laser system. At low feed rates powder feeder systems have perturbations. The study focused on relationship between the perturbation frequencies by inherent powder feeder designs and its impact on deposition quality. Performance metric determine the relation between perturbations in the powder flow and quality of the deposit. To determine performance metric, various powder feeder designs were analyzed. Perturbation frequencies were introduced to the disk feeder design. The quality of the deposit was determined by the surface roughness of …

Go to article

Modeling Of Powder Bed Processing -- A Review, Aaron Flood, Frank W. Liou Aug 2015

Modeling Of Powder Bed Processing -- A Review, Aaron Flood, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Many models have been developed to model powder beds and these methods can be implemented to model a powder bed for Selective Laser Sintering, Selective Laser Melting and any other technique of additive manufacturing which uses powder beds. Two of the main systems are the Discrete Element Method (DEM) and the Geometric Method. The purpose of this paper is to analyze each of the methods. It will first highlight how each of the models creates the powder bed. The next aspect reviewed is the computational time and its causes. And lastly, each of the methods will be examined for their …

Go to article

Methods Of Extrusion On Demand For High Solids Loading Ceramic Paste In Freeform Extrusion Fabrication, Wenbin Li, Amir Ghazanfari, Ming-Chuan Leu, Robert G. Landers Aug 2015

Methods Of Extrusion On Demand For High Solids Loading Ceramic Paste In Freeform Extrusion Fabrication, Wenbin Li, Amir Ghazanfari, Ming-Chuan Leu, Robert G. Landers

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Fabrication of highly dense parts with complex geometry by paste-extrusion-based solid freeform fabrication processes requires a precise control of the extrusion flow rate to dispense material on demand, which is often referred as Extrusion-On-Demand (EOD). The extrusion process for aqueous ceramic pastes is complex and difficult to control due to their non-Newtonian behavior, compressibility and inhomogeneity. In this study, three methods of EOD (based on ram extruder, needle valve, and auger valve) are introduced and investigated for the extrusion of high solids loading (i.e., > 50%, volumetric) aqueous alumina paste. Optimal extrusion process parameters for these methods are determined through printing …

Go to article

Depth Of Cut Monitoring For Hybrid Manufacturing Using Acoustic Emission Sensor, Haythem Gaja, Frank W. Liou Aug 2015

Depth Of Cut Monitoring For Hybrid Manufacturing Using Acoustic Emission Sensor, Haythem Gaja, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Laser Metal Deposition LMD is a hybrid manufacturing process consist of a laser deposition system combined with a 5-axis CNC milling system. During laser deposition many parameters and their interaction affect the dimensional accuracy of the part produced, powder flow rate, laser power and travel speed are some of these parameters. Sensing the acoustic emission during milling marching gives feedback information regarding depth of metal being cut subsequent part dimensions, if an error in dimensions is found certain actions, such as remaching, close loop control, or laser remelting can be carried out to correct it. Thus a reliable hybrid manufacturing …

Go to article

Planning Freeform Extrusion Fabrication Processes With Consideration Of Horizontal Staircase Effect, Amir Ghazanfari, Wenbin Li, Ming-Chuan Leu, Robert G. Landers Aug 2015

Planning Freeform Extrusion Fabrication Processes With Consideration Of Horizontal Staircase Effect, Amir Ghazanfari, Wenbin Li, Ming-Chuan Leu, Robert G. Landers

Mechanical and Aerospace Engineering Faculty Research & Creative Works

An algorithm has been developed to estimate the “horizontal” staircase effect and a technique is proposed to reduce this type of geometrical error for freeform extrusion fabrication processes of 3D “solid” parts. The adaptive rastering technique, proposed in this paper, analyzes the geometry of each layer and changes the width of each line of the raster adaptively in order to reduce the staircase error and increase the productivity simultaneously. For each line, the maximum width that results in a staircase error smaller than a predefined threshold is determined for decreasing the fabrication time or increasing the dimensional accuracy, or both. …

Go to article

Direct Laser Deposition Of Ti-6al-4v From Elemental Powder Blends, Lei Yan, Xueyang Chen, Wei Li, Frank W. Liou, Joseph William Newkirk Aug 2015

Direct Laser Deposition Of Ti-6al-4v From Elemental Powder Blends, Lei Yan, Xueyang Chen, Wei Li, Frank W. Liou, Joseph William Newkirk

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A thin-wall structure composed of Ti-6Al-4V has been deposited using direct laser deposition (DLD) from blended Ti, Al, and V elemental powders. The microstructure and composition distribution along the build height direction were intensively investigated using optical microscopy, scanning electron microscopy/energy dispersive X-ray spectroscopy (SEM/EDS), and Vickers hardness testing. The microstructures of the as-deposited Ti-xAl-yV were studied using EDS to determine appropriate weight percentage for Al and V in the blended powders before mixing. The effects of laser power and laser transverse speed on the microstructure were investigated and optimized laser processing parameters were concluded.

Go to article

Solid Freeform Fabrication Of Transparent Fused Quartz Using A Filament Fed Process, J. Luo, L. J. Gilbert, C. Qu, B. Morrow, Douglas A. Bristow, Robert G. Landers, J. Goldstein, A. Urbas, Edward C. Kinzel Aug 2015

Solid Freeform Fabrication Of Transparent Fused Quartz Using A Filament Fed Process, J. Luo, L. J. Gilbert, C. Qu, B. Morrow, Douglas A. Bristow, Robert G. Landers, J. Goldstein, A. Urbas, Edward C. Kinzel

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Glass is a critical material for many scientific and engineering applications including optics, communications, electronics, and hermetic seals. Despite this technological relevance, there has been minimal research toward Additive Manufacturing (AM) of glass, particularly optically transparent glass. Additive Manufacturing of transparent glass offers potential advantages for lower processing costs for small production volumes, increased design freedom, and the ability to locally vary the optical properties of the part. Compared to common soda lime glass, fused quartz is better for AM since it has lower thermal expansion and higher index homogeneity. This paper presents a study of additive manufacturing of transparent …

Go to article

Freeform Extrusion Fabrication Of Titanium Fiber Reinforced Bioactive Glass Scaffolds, Albin Thomas, Krishna C. R. Kolan, Ming-Chuan Leu, Greg Hilmas Aug 2015

Freeform Extrusion Fabrication Of Titanium Fiber Reinforced Bioactive Glass Scaffolds, Albin Thomas, Krishna C. R. Kolan, Ming-Chuan Leu, Greg Hilmas

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Although implants made with bioactive glass have shown promising results for bone repair, their application in repairing load-bearing long bones is limited due to their low fracture toughness and fairly fast degradation response in vivo. In this paper, we describe our investigation of freeform extrusion fabrication of silicate based 13-93 bioactive glass scaffolds reinforced with titanium fibers. A composite paste was prepared with 13-93 bioactive glass filled with titanium fibers (~16 µm in diameter and aspect ratio of ~250) having a volume fraction of 0.4 vol. %. This paste was then extruded to fabricate scaffolds with an extrudate diameter …

Go to article

Dc-Gain Layer-To-Layer Stability Criterion In Laser Metal Deposition Processes, Patrick M. Sammons, Douglas A. Bristow, Robert G. Landers Aug 2015

Dc-Gain Layer-To-Layer Stability Criterion In Laser Metal Deposition Processes, Patrick M. Sammons, Douglas A. Bristow, Robert G. Landers

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In Laser Metal Deposition (LMD), a blown powder metal additive manufacturing process, functional metal parts are fabricated in a layer-by-layer fashion. In addition to the in-layer dynamics, which describe how the process evolves within a given layer, the additive-fabrication property of LMD creates a second set of dynamics which describe how the process evolves from layer-to-layer. While these dynamics, termed layer-to-layer dynamics, are coupled with both the in-layer dynamics and the process operating conditions, they are not widely considered in the modeling, process planning, or process control of LMD operations. Because of this, seemingly valid choices for process parameters can …

Go to article

A Framework For Large Scale Fused Pellet Modeling (Fpm) By An Industry Robot, Zhiyuan Wang, Renwei Liu, Todd E. Sparks, Frank W. Liou Aug 2015

A Framework For Large Scale Fused Pellet Modeling (Fpm) By An Industry Robot, Zhiyuan Wang, Renwei Liu, Todd E. Sparks, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Fused pellet modeling (FPM) is an important method in additive manufacturing technology, where granular material is used instead of filaments. In FPM, prototypes are constructed by the sequential deposition of material layers. As the size of the part increases, the problem of long build times and part deformation becomes critical. In this paper, methods for eliminating the void density during deposition and accuracy control principles for large scale FPM processes are studied. By analyzing the ab initio principles of this process, a mini extruder with variable pitch and progressive diameter screw for the large scale fused deposition is proposed. Based …

Go to article

A Mechanical Testing Methodology For Additive Manufacturing Processes, Sujitkumar Dongare, Todd E. Sparks, Joseph William Newkirk, Frank W. Liou Aug 2014

A Mechanical Testing Methodology For Additive Manufacturing Processes, Sujitkumar Dongare, Todd E. Sparks, Joseph William Newkirk, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Most additive manufacturing processes are layer-by-layer deposition, thus its mechanical properties could be very different than those made from traditional manufacturing processes. This paper summarizes a mini-tensile testing methodology for additive manufacturing. Research concerning the tensile testing of metallic material has been conducted and test methods have been defined. It encompasses the methods for determination of yield strength, yield point elongation, tensile strength, elongation, and reduction of area. The study of positional variation and cooling-rate dependency in case of additive manufacturing proves to be expensive and time consuming with the full-size test specimens. Thus, this paper discussed a technique for …

Go to article

Investigation Of Forged-Like Microstructure Produced By A Hybrid Manufacturing Process, Romy Francis, Joseph William Newkirk, Frank W. Liou Aug 2014

Investigation Of Forged-Like Microstructure Produced By A Hybrid Manufacturing Process, Romy Francis, Joseph William Newkirk, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Laser Metal Deposition (LMD) is an additive manufacturing technique for manufacturing complex near net shaped components. The grain size of the typical deposition microstructure in case of Ti-6Al-4V can range between 100µm-600µm, which is much larger than that of forged-like microstructures. Friction Stir Processing (FSP) has been investigated as a method for surface modification to form refined microstructure at the surface of the Ti-6Al-4V components manufactured from the LMD method. Integration of FSP and LMD can greatly improve the product properties. Friction stir processing of the laser deposited Ti-6Al-4V deposits was performed and optimum processing parameters were obtained using this …

Go to article

Stereo Vision Based Hybrid Manufacturing Of Ti-6al-4v In Component Repair Process, Renwei Liu, Zhiyuang Wang, Todd E. Sparks, Frank W. Liou Aug 2014

Stereo Vision Based Hybrid Manufacturing Of Ti-6al-4v In Component Repair Process, Renwei Liu, Zhiyuang Wang, Todd E. Sparks, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Parts or products from high performance metal are very expensive, partly due to the processing complexities during manufacturing. Recent studies have indicated that hybrid processes of additive manufacturing and machining process can be used to repair titanium parts, thus extending the service life. In order to implement these methods automatically, it is necessary to obtain the spatial geometry information of component with defects to generate the tool path. The purpose of this paper is to summarize the research on hybrid manufacturing with stereo vision function which can be applied to the component repair process. Stereo vision is adopted to detect …

Go to article

In Vitro Assessment Of Laser Sintered Bioactive Glass Scaffolds With Different Pore Geometries, Krishna C. R. Kolan, Albin Thomas, Ming-Chuan Leu, Greg Hilmas Aug 2014

In Vitro Assessment Of Laser Sintered Bioactive Glass Scaffolds With Different Pore Geometries, Krishna C. R. Kolan, Albin Thomas, Ming-Chuan Leu, Greg Hilmas

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The pore geometry of bioactive glass scaffolds intended for use in bone repair or replacement is one of the most important parameters that could determine the rate of bone regeneration. The pore geometry would also affect the mechanical properties of the scaffolds and their rate of degradation. Scaffolds with five different architectures, having ~50% porosity, were fabricated with silicate (13–93) and borate (13–93B3) based bioactive glasses using a laser sintering process. An established, late-osteoblasts/early-osteocytes cell line was used to perform cell proliferation tests on the scaffolds. The results indicated that the cells proliferate significantly more on the scaffolds which mimic …

Go to article

Thermographic Investigation Of Laser Metal Deposition, Sreekar Karnati, Todd E. Sparks, Frank W. Liou Aug 2014

Thermographic Investigation Of Laser Metal Deposition, Sreekar Karnati, Todd E. Sparks, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Primitive stages of studies on and with additive manufacturing techniques popularly involve thin wall geometry. In the current effort attempts were made to capture various thermal aspects during deposition of a thin wall geometry. The thermo-graphic data was captured using a FLIR A615 infrared camera. Post processing using edge detection algorithms and image processing techniques, the geometric and thermal aspects of meltpool and tail of the meltpool were obtained. The effect of geometry and power on shape of the meltpool and its tail were obtained. The depositions of SS 316 with varying power. These observations were discussed and analyzed in …

Go to article

Investigation Of Sparse-Build Rapid Tooling By Fused Deposition Modeling, Osman Iyibilgin, Ming-Chuan Leu, Gregory Taylor, H. Li, K. Chandrashekhara Aug 2014

Investigation Of Sparse-Build Rapid Tooling By Fused Deposition Modeling, Osman Iyibilgin, Ming-Chuan Leu, Gregory Taylor, H. Li, K. Chandrashekhara

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper describes the investigation of sparse-build tooling by Fused Deposition Modeling (FDM®) aimed at rapid tooling with reduction in the amount of material. Sparse-build test coupons having ULTEM as the material and varying air gap (sparse spacing), wall thickness, and cap thickness were fabricated using the sparse and sparse-double dense build styles of the Stratasys Fortus machine. The strengths and moduli of these coupons were measured in compression and flexure tests. The strength/mass ratio and modulus/mass ratio were compared among the various coupons, as well as with solid coupons, to investigate the effects of the two build styles and …

Go to article

Probabilistic Simulation Of Solidification Microstructure Evolution During Laser-Based Metal Deposition, Jingwei Zhang, Frank W. Liou, William Seufzer, Joseph William Newkirk, Zhiqiang Fan, Heng Liu, Todd E. Sparks Aug 2013

Probabilistic Simulation Of Solidification Microstructure Evolution During Laser-Based Metal Deposition, Jingwei Zhang, Frank W. Liou, William Seufzer, Joseph William Newkirk, Zhiqiang Fan, Heng Liu, Todd E. Sparks

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A predictive model, based on a Cellular Automaton (CA) - Finite Element (FE) method, has been developed to simulate microstructure evolution during metal solidification for a laser based additive manufacturing process. The macroscopic FE calculation was designed to update the temperature field and simulate a high cooling rate. In the microscopic CA model, heterogeneous nucleation sites, preferential growth orientation and dendritic grain growth kinetics were simulated. The CA model was able to show the entrapment of neighboring cells and the relationship between undercooling and the grain growth rate. The model predicted the dendritic grain size, structure, and morphological evolution during …

Go to article

Effect Of Architecture And Porosity On Mechanical Properties Of Borate Glass Scaffolds Made By Selective Laser Sintering, Krishna C. R. Kolan, Ming-Chuan Leu, Greg Hilmas, Taylor Comte Aug 2013

Effect Of Architecture And Porosity On Mechanical Properties Of Borate Glass Scaffolds Made By Selective Laser Sintering, Krishna C. R. Kolan, Ming-Chuan Leu, Greg Hilmas, Taylor Comte

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The porosity and architecture of bone scaffolds, intended for use in bone repair or replacement, are two of the most important parameters in the field of bone tissue engineering. The two parameters not only affect the mechanical properties of the scaffolds but also aid in determining the amount of bone regeneration after implantation. Scaffolds with five different architectures and four porosity levels were fabricated using borate bioactive glass (13-93B3) using the selective laser sintering (SLS) process. The pore size of the scaffolds varied from 400 to 1300 μm. The compressive strength of the scaffolds varied from 1.7 to 15.5 MPa …

Go to article

Development Of Freeze-Form Extrusion Fabrication With Use Of Sacrificial Material, Ming-Chuan Leu, Diego A. Garcia Aug 2013

Development Of Freeze-Form Extrusion Fabrication With Use Of Sacrificial Material, Ming-Chuan Leu, Diego A. Garcia

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The development of Freeze-form Extrusion Fabrication (FEF) process to fabricate three-dimensional (3D) ceramic parts with use of sacrificial material to build support sections during the fabrication process is presented in this paper. FEF is an environmentally friendly, additive manufacturing process that builds 3D parts in a freezing environment layer-by-layer by computer controlled extrusion and deposition of aqueous colloidal pastes based on computer-aided design (CAD) models. Methyl cellulose was identified as the support material, and alumina was used as the main material in this study. After characterizing the dynamics of extruding alumina and methyl cellulose pastes, a general tracking controller was …

Go to article

First Prev Next Last