Signal Processing Commons^™

Design And Assembly Of High-Temperature Signal Conditioning System On Ltcc With Silicon Carbide Cmos Circuits, Sajib Roy

Graduate Theses and Dissertations

The objective of the work described in this dissertation paper is to develop a prototype electronic module on a low-temperature co-fired ceramic (LTCC) material. The electronic module would perform signal conditioning of sensor signals (thermocouples) operating under extreme conditions for applications like gas turbines to collect data on the health of the turbine blades during operation so that the turbines do not require shutdown for inspection to determine if maintenance is required. The collected data can indicate when such shutdowns, which cost $1M per day, should be scheduled and maintenance actually performed. The circuits for the signal conditioning system within …

Distance-Based Formation Control Using Decentralized Sensing With Infrared Photodiodes, Steven Williams

LSU Master's Theses

This study presents an onboard sensor system for determining the relative positions of mobile robots, which is used in decentralized distance-based formation controllers for multi-agent systems. This sensor system uses infrared photodiodes and LEDs; its effective use requires coordination between the emitting and detecting robots. A technique is introduced for calculating the relative positions based on photodiode readings, and an automated calibration system is designed for future maintenance. By measuring the relative positions of their neighbors, each robot is capable of running an onboard formation controller, which is independent of both a centralized controller and a global positioning-like system (e.g., …

Calculate The Reliability Of The Bts-Bsc Network With The Reserved Line Connection, Dilmurod Davronbekov, Utkir Karimovich Matyokubov

Chemical Technology, Control and Management

The issue of reserving communication lines between the base station and the mobile network base station controller which are considered as one system is considered. Analytical expressions have been developed for calculating the reliability of the system for various options for backing up communication lines between the base station and the base station controller. The results of research and calculations of reliability for ten different types of backup communication lines of the base station and the base station controller are presented.

The Use Of Supercapacitors To Stabilize The Power Supply System Of The Base Station Of Mobile Communication, Dilmurod Abdujalilovich Davronbekov, Utkir Karimovich Matyokubov

Scientific-technical journal

In this study, an analysis of the current status and available outages of the mobile communication base station power supply system was performed. The effects of these outages on the power supply system have been studied and it has been shown that batteries may not be an ideal solution as a backup source. Also, the issue of the introduction of renewable energy sources in the base station power supply system of the mobile communication system and its shortcomings are mentioned. In order to overcome these problems and stabilize the power changes in the battery auxiliary element and the power supply …

The Use Of Supercapacitors To Stabilize The Power Supply System Of The Base Station Of Mobile Communication, Dilmurod Abdujalilovich Davronbekov, Utkir Karimovich Matyokubov

Scientific-technical journal

In this study, an analysis of the current status and available outages of the mobile communication base station power supply system was performed. The effects of these outages on the power supply system have been studied and it has been shown that batteries may not be an ideal solution as a backup source. Also, the issue of the introduction of renewable energy sources in the base station power supply system of the mobile communication system and its shortcomings are mentioned. In order to overcome these problems and stabilize the power changes in the battery auxiliary element and the power supply …

Channel Estimation In Multi-User Massive Mimo Systems By Expectation Propagation Based Algorithms, Mohammed Rashid

LSU Doctoral Dissertations

Massive multiple input multiple output (MIMO) technology uses large antenna arrays with tens or hundreds of antennas at the base station (BS) to achieve high spectral efficiency, high diversity, and high capacity. These benefits, however, rely on obtaining accurate channel state information (CSI) at the receiver for both uplink and downlink channels. Traditionally, pilot sequences are transmitted and used at the receiver to estimate the CSI. Since the length of the pilot sequences scale with the number of transmit antennas, for massive MIMO systems downlink channel estimation requires long pilot sequences resulting in reduced spectral efficiency and the so-called pilot …

Time Series Data Analysis Using Machine Learning-(Ml) Approach, Mvv Prasad Kantipudi Dr., Pradeep Kumar N.S Dr., S.Sreenath Kashyap Dr., Ss Anusha Vemuri Ms

Library Philosophy and Practice (e-journal)

Healthcare benefits related to continuous monitoring of human movement and physical activity can potentially reduce the risk of accidents associated with elderly living alone at home. Based on the literature review, it is found that many studies focus on human activity recognition and are still active towards achieving practical solutions to support the elderly care system. The proposed system has introduced a joint approach of machine learning and signal processing technology for the recognition of human's physical movements using signal data generated by accelerometer sensors. The framework adopts the concept of DSP to select very descriptive feature sets and uses …

Sensing Methods For Two-Target And Four-Target Detection In Time-Constrained Vector Poisson And Gaussian Channels, Muhammad Fahad

Dissertations, Master's Theses and Master's Reports

In this dissertation we consider a sensor scheduling or resource management problem for a vector Poisson and Gaussian channels. The input is a binary random vector and the output is a set of conditionally independent Poisson or Gaussian random variables. The objective is to design a scaling matrix, which is a linear transformation whose purpose is to entangle the different inputs, under a total given energy/time constraint. The two metrics are adopted to quantify the performance of the designed scaling matrix: mutual information and Bayesian inference. In other words, it is an experimental design problem where the objective is to …

Hard Hat Ambient Liability Observer (Halo), Hunter Hykes, Nathan Kish, Brian Thomson

Williams Honors College, Honors Research Projects

Capturing workplace incident information is a growing area of concern for most companies. To assist with this, the design team proposed the H.A.L.O. This design uses time-of-flight sensors connected to LEDs to create a proximity-based hazard warning system. It also records incident data using an accelerometer and micro-SD card. This helps workers avoid some of the most common workplace injuries, slips, trips, and falls and accidental collisions.

Students have created a design with engineering, and marketing requirements that accomplish this task. The proposed design allows for this monitoring and mitigation systems to be attached to hard hats. Team members developed …

Deep Models For Improving The Performance And Reliability Of Person Recognition, Sobhan Soleymani

Graduate Theses, Dissertations, and Problem Reports (ETD)

Deep models have provided high accuracy for different applications such as person recognition, image segmentation, image captioning, scene description, and action recognition. In this dissertation, we study the deep learning models and their application in improving the performance and reliability of person recognition. This dissertation focuses on five aspects of person recognition: (1) multimodal person recognition, (2) quality-aware multi-sample person recognition, (3) text-independent speaker verification, (4) adversarial iris examples, and (5) morphed face images. First, we discuss the application of multimodal networks consisting of face, iris, fingerprint, and speech modalities in person recognition. We propose multi-stream convolutional neural network architectures …

Re-Design Of Precision Signal Conditioning Circuit For Detecting Schumann Resonance, Rohith Bikkina

Graduate Theses, Dissertations, and Problem Reports (ETD)

Extremely low frequencies signals are waves between 3 to 30Hz and corresponding wavelengths between 10,000 to 100,000 kilometers. The specific signals used here are generated from lightning and are excited at frequencies around 8Hz, 14Hz, 20Hz. These are often called Schumann Resonance frequencies. Several stations have been built around the world for identifying ELF waves. All of those required a sparsely populated area that was far away from electric power lines because of interference from electric noise at 50 Hz and 60Hz. This project develops and tests an amplifier and filter circuit that should assist in identifying the Schumann Resonance …

Analysis Of Millimeter-Wave Networks: Blockage, Antenna Directivity, Macrodiversity, And Interference, Enass Hriba

Graduate Theses, Dissertations, and Problem Reports (ETD)

Due to its potential to support high data rates at low latency with reasonable interference isolation because of signal blockage at these frequencies, millimeter-wave (mmWave) communications has emerged as a promising solution for next-generation wireless networks. MmWave systems are characterized by the use of highly directional antennas and susceptibility to signal blockage by buildings and other obstructions, which significantly alter the propagation environment. The received power of each transmission depends on the direction the corresponding antennas point and whether the signal’s path is line-of-sight (LOS), non-LOS (i.e., partially blocked), or completely blocked. A key challenge in modeling blocking in mmWave …

Technique Design Of Filter On Surface-Acoustic Waves, Dilmurod Abdujalilovich Davronbekov, Zafar Tulyaganovich Khakimov

Acta of Turin Polytechnic University in Tashkent

The article describes the design of filters on surface acoustic waves (SAWs), which are selective elements and are widely used in blocks, devices and signal processing systems in telecommunications, including wireless communication systems such as cellular, trunking and others. Designs of filters for surfactants are considered, which are divided into two large groups - by functional purpose and by a systematic approach to the synthesis of performance characteristics of filters for surfactants. Optimization algorithms and methods for synthesizing surfactant filters have been developed and improved. An improved technique for the synthesis of a filter based on surface acoustic waves is …

Multibeam Array Antenna For Base Station In The Fifth-Generation Mobile Communication System, Intan Izafina Idrus

Student Works (2020-2029)

Research on the fifth-generation (5G) mobile communication system has been accelerated to meet the standardization of the International Telecommunications Union for higher data traffic and higher data rates. The main requirements of the 5G mobile communication systems are the utilization of millimeter waves, the deployment of small cells, and the use of multibeam array antennas for multiple-input multiple-output schemes. Multibeam array antennas play an important role in developing a new base station to enhance system capacity, improve network coverage, and reduce co-channel interference. The main objective of this thesis is to design a single-layer multibeam array antenna at 28 GHz …

An Exploratory Study Of Pulse Width And Delta Sigma Modulators, Logan B. Penrod

Master's Theses

This paper explores the noise shaping and noise producing qualities of Delta-Sigma Modulators (DSM) and Pulse-Width Modulators (PWM). DSM has long been dominant in the Delta Sigma Analog-to-Digital Converter (DSADC) as a noise-shaped quantizer and time discretizer, while PWM, with a similar self oscillating structure, has seen use in Class D Power Amplifiers, performing a similar function. It has been shown that the PWM in Class D Amplifiers outperforms the DSM [1], but could this advantage be used in DSADC use-cases? LTSpice simulation and printed circuit board implementation and test are used to present data on four variations of these …

Designing And Evaluating Of Mimo Systems For Millimeter-Wave Communications, Mojtaba Ahmadi Almasi

Boise State University Theses and Dissertations

The fifth generation (5G) of wireless communications will integrate all existing technologies while bringing its own to the system. Amongst these technologies, millimeter-wave (mmWave) is emerging as a promising solution for 5G systems. However, to fully harness the potential of mmWave communications, obstacles such as severe path loss, channel sparsity, and hardware complexity should be overcome. The existing cost-effective systems can considerably reduce the hardware complexity and partially severe path loss, while channel sparsity still remains a main problem. Other factors such as transmission reliability and coverage area should be considered in 5G mmWave communications. Non-orthogonal multiple access (NOMA) is …

Power-Weighted Lpc Formant Estimation, Ruairí De Fréin

Conference papers

A power-weighted formant frequency estimation procedure based on Linear Predictive Coding (LPC) is presented. It works by pre-emphasizing the dominant spectral components of an input signal, which allows a subsequent estimation step to extract formant frequencies with greater accuracy. The accuracy of traditional LPC formant estimation is improved by this new power-weighted formant estimator for different classes of synthetic signals and for speech. Power-weighted LPC significantly and reliably outperforms LPC and variants of LPC at the task of formant estimation using the VTR formants dataset, a database consisting of the Vocal Tract Resonance (VTR) frequency trajectories obtained by human experts …

Ofdm Simulation, Joseph W. Bednar

Electrical Engineering

The project objective is to provide a tool that will allow the user to simulate an adaptive OFDM (Orthogonal Frequency-Division Multiplexing) communication system in the presence of various types of interference and noise. The open-source code allows students and engineers to adjust the modulation, threshold settings, and distortion effects in the channel while observing the output bit error rate. The results the simulation provides will aid researchers in attempting to characterize the interference of OFDM based systems and their effectiveness in the presence of noise.

The Role Of Network Components In Improving The Reliability And Survivability Of Mobile Communication Networks, Dilmurod Davronbekov, Utkir Karimovich Matyokubov

Acta of Turin Polytechnic University in Tashkent

This article compares the different architectures of mobile communication networks (MCN) and examines the survivability of the network. Typical survival strategies for improving MCN survivability, failure mitigation strategies for network elements, wireless network survival rates, failure scenarios at MCN levels, and survival indicators are presented. The importance of fiber-optic communication in the construction of communication lines between MCN components has been studied. The issue of designing MCNs in a cost-effective and highly viable way is considered, and the necessary expressions of the design process are given.

Electromagnetic Characteristics Of The Soil, Abdul Salam, Usman Raza

Faculty Publications

The electromagnetic characteristics of the soil are discussed in this chapter. The characteristics of porous bedrock, soil medium, and impacts of rain attenuations are also presented. The models of dielectric soil properties are studied with a rigorous focus on the constitutive parameters of subsurface soil medium. Moreover, the permittivity and wavenumber in soil are explained. In addition, the frequency-dependent dielectric properties such as dispersion in soil, absorption characteristic, and penetration depth versus frequency are reviewed. Furthermore, the effective permittivity of soil–water mixture for through-the soil-propagation mechanism is analyzed thoroughly.

Wireless Underground Channel Modeling, Abdul Salam, Usman Raza

Faculty Publications

A comprehensive treatment of wireless underground channel modeling is presented in this chapter. The impacts of the soil on bandwidth and path loss are analyzed. A mechanism for the UG channel sounding and multipath characteristics analysis is discussed. Moreover, novel time-domain impulse response model for WUC is reviewed with the explanation of model parameters and statistics. Furthermore, different types of the through-the-soil wireless communications are surveyed. Finally, the chapter concludes with discussion of the UG wireless statistical model and path loss model for through-the-soil wireless communications in decision agriculture. The model presented in this chapter is also validated with empirical …

Signals In The Soil: An Introduction To Wireless Underground Communications, Abdul Salam, Usman Raza

Faculty Publications

In this chapter, wireless underground (UG) communications are introduced. A detailed overview of WUC is given. A comprehensive review of research challenges in WUC is presented. The evolution of underground wireless is also discussed. Moreover, different component of UG communications is wireless. The WUC system architecture is explained with a detailed discussion of the anatomy of an underground mote. The examples of UG wireless communication systems are explored. Furthermore, the differences of UG wireless and over-the-air wireless are debated. Different types of wireless underground channel (e.g., In-Soil, Soil-to-Air, and Air-to-Soil) are reported as well.

Underground Phased Arrays And Beamforming Applications, Abdul Salam, Usman Raza

Faculty Publications

This chapter presents a framework for adaptive beamforming in underground communication. The wireless propagation is thoroughly analyzed to develop a model using the soil moisture as an input parameter to provide feedback mechanism while enhancing the system performance. The working of array element in the soil is analyzed. Moreover, the effect of soil texture and soil moisture on the resonant frequency and return loss is studied in detail. The wave refraction from the soil–air interface highly degrades the performance of the system. Furthermore, to beam steering is done to achieve high gain for lateral component improving the UG communication. The …

Current Advances In Internet Of Underground Things, Abdul Salam, Usman Raza

Faculty Publications

The latest developments in Internet of Underground Things are covered in this chapter. First, the IOUT Architecture is discussed followed by the explanation of the challenges being faced in this paradigm. Moreover, a comprehensive coverage of the different IOUT components is presented that includes communications, sensing, and system integration with the cloud. An in-depth coverage of the applications of the IOUT in various disciplines is also surveyed. These applications include areas such as decision agriculture, pipeline monitoring, border control, and oil wells.

Modulation Schemes And Connectivity In Wireless Underground Channel, Abdul Salam, Usman Raza

Faculty Publications

In this chapter, a thorough treatment of the modulation schemes for UG Wireless is presented. The effects of soil texture and water content on the capacity of multi-carrier modulation in WUC are discussed. The multi-carrier capacity model results are analyzed. Moreover, the underground MIMO design for underground communications is explained thoroughly. An analysis of medium access in wireless underground is done as well. Furthermore, the soil properties are considered for cross-layer communications of UG wireless. The performance analysis of traditional modulation schemes is also considered. The soil moisture-based modulation approach is also explored in this chapter. The connectivity and diversity …

Wideband Satcom Model: Evaluation Of Numerical Accuracy And Efficiency, Andrew J. Knisely, Andrew Terzuoli

Faculty Publications

The spectral method is typically applied as a simple and efficient method to solve the parabolic wave equation in phase screen scintillation models. The critical factors that can greatly affect the spectral method accuracy is the uniformity and smoothness of the input function. This paper observes these effects on the accuracy of the finite difference and the spectral methods applied to a wideband SATCOM signal propagation model simulated in the ultra-high frequency (UHF) band. The finite difference method uses local pointwise approximations to calculate a derivative. The spectral method uses global trigonometric interpolants that achieve remarkable accuracy for continuously differentiable …

Fault Location In Distribution System Based On Voltage Sag Analysis, Ahmad Muhamad Firdaus

Student Works (2020-2029)

Fault in the distribution system is something that cannot be avoided. It is a recurring event that occurs due to various factors such as natural occurrence, mechanism failure, or human error. All this contributes to the phenomenon that will affect the stability of the system and result in the loss of power to the consumers. However, such a fault is something that happens unexpectedly, and it is difficult to be eliminated. Therefore, various research work has been done over the years to overcome the problem. All research is done to find the most effective method of finding the fault location …

Hybrid Microwave Power Amplifiers For Broadband Communication, Sangaran Pragash

Student Works (2020-2029)

The software-defined radio is the future of radio technology. The development of a broadband power amplifier is the most challenging radio component to design in achieving software-defined radio goals due to the PA gain-bandwidth limitation. The distributed power amplifier (DPA) overcomes the limitation by combining output power from several transistors in an additive fashion. Matrix Amplifier (MA) consists of two or more DPA stacked together in a multiplicative manner. In this project, a high power and high gain DPA for a two-way radio system is demonstrated. The DPA exhibits 10W output power and 32dB gain across the frequency range of …

Indoor Positioning Using Acoustic Pseudo-Noise Based Time Difference Of Arrival, Nicholas J. Luong

Master's Theses

The Global Positioning System (GPS) provides good precision on a global scale, but is not suitable for indoor applications. Indoor positioning systems (IPS) aim to provide high precision position information in an indoor environment. IPS has huge market opportunity with a growing number of commercial and consumer applications especially as Internet of Things (IoT) develops. This paper studies an IPS approach using audible sound and pseudo-noise (PN) based time difference of arrival (TDoA). The system’s infrastructure consists of synchronized speakers. The object to be located, or receiver, extracts TDoA information and uses multilateration to calculate its position. The proposed IPS …

Distance Estimation Using Ofdm Signals For Ultrasonic Positioning, Kyman Huang

Master's Theses

This paper describes a method of estimating distance via Time-of-Flight (TOF) measurement using ultrasonic Orthogonal Frequency Division Multiplexing (OFDM) signals. Using OFDM signals allows the signals and their sub-carriers to remain orthogonal to each other while continuously transmitting. This estimation method is based on the change of phase of a traveling wave as it propagates through a medium (air for ultrasonic signals). By using signals containing multiple tones, the phase change between each frequency component is slightly different. This phase difference is dependent on the distance traveled and can thus be used to estimate distance. This paper studies the impact …