Electrical and Electronics Commons^™

Experimental Study And Modeling Of The Gm-I Dependence Of Long-Channel Mosfets, Michael Fong Cheng

Master's Theses

This thesis describes an experimental study and modeling of the current-transconductance dependence of the ALD1106, ALD1107, and CD4007 arrays. The study tests the hypothesis that the I-gm dependence of these 7.8 µm to 10 µm MOSFETs conforms to the Advanced Compact Model (ACM). Results from performed measurements, however, do not support this expectation. Despite the relatively large length, both ALD1106 and ALD1107 show sufficiently pronounced ‘short-channel’ effects to render the ACM inadequate. As a byproduct of this effort, we confirmed the modified ACM equation. With an m factor of approximately 0.6, it captures the I-gm dependence with sub-28% maximum error …

Development Of A Myoelectric Detection Circuit Platform For Computer Interface Applications, Nickolas Andrew Butler

Master's Theses

Personal computers and portable electronics continue to rapidly advance and integrate into our lives as tools that facilitate efficient communication and interaction with the outside world. Now with a multitude of different devices available, personal computers are accessible to a wider audience than ever before. To continue to expand and reach new users, novel user interface technologies have been developed, such as touch input and gyroscopic motion, in which enhanced control fidelity can be achieved. For users with limited-to-no use of their hands, or for those who seek additional means to intuitively use and command a computer, novel sensory systems …

Nanosatellite Launch Data-Logger (Sync), Christopher Martin Gerdom

Master's Theses

CubeSat designers are increasingly looking to incorporate delicate structures and optics into their payloads. These delicate payloads, however, may not survive the required absolute-worst-case launch vibration testing needed for flight certification. To help address this problem, and to better match testing conditions to real-world launch environments, this thesis introduces Sync, a compact 1/4U CubeSat payload designed to collect data on the vibrations and thermal environments CubeSats experience inside a deployer on the way to orbit. This data can be used to better understand the launch environment for different vehicles, and help develop new, more realistic testing guidelines that could enable …

A Computational Analysis Of The Gradient Concentration Profile Of Deet And The Mosquito Behavioral Response, Brandon Carver

Master's Theses

DEET is a common active ingredient in most spatial repellents. DEET is also a volatile organic compound. DEET prevents mosquitoes from detecting and coming into contact with an human individual. Gas sensing technologies such as metal oxide semiconductor sensors can detect VOCs. The World Health Organization provides the majority of efficacy testing methods. This research adapts methods from the WHO and use of MOS sensors to further understand how and why DEET affects mosquitos. A custom developed system is used to measure DEET dissipation and observe mosquito behavioral response to the DEET. DEET dissipations and mosquito behavior is measured within …

The Design, Building, And Testing Of A Constant On Discreet Jammer For The Ieee 802.15.4/Zigbee Wireless Communication Protocol, Alexandre J. Marette

Master's Theses

As wireless protocols become easier to implement, more products come with wireless connectivity. This latest push for wireless connectivity has left a gap in the development of the security and the reliability of some protocols. These wireless protocols can be used in the growing field of IoT where wireless sensors are used to share information throughout a network. IoT is being implemented in homes, agriculture, manufactory, and in the medical field. Disrupting a wireless device from proper communication could potentially result in production loss, security issues, and bodily harm. The 802.15.4/ZigBee protocol is used in low power, low data rate, …

Extended-Use Ecg Monitor, Daniel Aaron Soski

Master's Theses

In this thesis, a prototype ECG monitor was developed that is integrated into an elastic shirt and takes a 3-lead ECG for over 5 days. The high-quality measurements can be used to identify markers indicative of various detrimental heart conditions. Measurements recorded by the device are encrypted and stored onto a micro-SD card. Current Holter monitors are expensive and have functional lives less than 48 hours; however, extended duration monitoring has been proven more useful in diagnosis. The device designed demonstrates that ECG measurements can be taken over longer durations without sacrificing quality, comfort, or device cost.

The Modified-Multiphase Boost Converter: Combined Inductors And Capacitors Topology, Zachary L. Eldredge

Master's Theses

In this work, a modified boost converter design has been implemented in a multiphase configuration with a condensed topology. The modified aspect of the design has already been proven to drastically reduce input current ripple by about 40% in a single-phase implementation. By placing two modified boost converters in parallel with interleaving main switches (multiphase), the input inductors and modified capacitors of the modified topology can be reduced to just one of each, lowering the number of components, size, and cost. Additionally, multiphase DC/DC converters lower input/output voltage and current ripples while delivering more power compared to single-phase converters. By …

A Multiphase Modified Boost Converter With Reduced Input Current Ripple: Combined Capacitors, Omri Nissan

Master's Theses

The delivery of high power and smaller footprints through a non-isolated topology demands for the use of multiphase topology in DC-DC converters. Multiphase reduces the ripple observed on both the input and output waveforms; however, it may not be enough to connect to sensitive power sources such as renewable energy sources. A single-phase modified boost converter demonstrates the ability to acquire very minimal input current ripple by addition of passive components. The expansion to multiphase topology is the next logical step for higher power application while furthering the low input current ripple benefit. In this thesis, the multiphase modified boost …

Smart Dc/Dc Wall Plug Design For The Dc House Project, Richard Sinclair Liu

Master's Theses

The present day duplex wall receptacle in the United States provides 120Vrms AC at 60Hz, which comes from a standard set for AC loads by the National Electrical Manufacturers Association. With a DC system, such as what is used in the DC House project currently being developed at Cal Poly, providing DC power to DC loads presents a technical challenge due to the different required DC operating voltages of the loads. This thesis entails the design and construction of a Smart DC/DC Wall Plug, which can automatically adjust its output voltage to match any required DC load voltages. In the …

Design Of An Active Harmonic Rejection N-Path Filter For Highly Tunable Rf Channel Selection, Craig J. Fischer

Master's Theses

As the number of wireless devices in the world increases, so does the demand for flexible radio receiver architectures capable of operating over a wide range of frequencies and communication protocols. The resonance-based channel-select filters used in traditional radio architectures have a fixed frequency response, making them poorly suited for such a receiver. The N-path filter is based on 1960s technology that has received renewed interest in recent years for its application as a linear high Q filter at radio frequencies. N-path filters use passive mixers to apply a frequency transformation to a baseband low-pass filter in order to achieve …

Dc-Dc Converter Control System For The Energy Harvesting From Exercise Machines System, Alexander Sireci

Master's Theses

Current exercise machines create resistance to motion and dissipate energy as heat. Some companies create ways to harness this energy, but not cost-effectively. The Energy Harvesting from Exercise Machines (EHFEM) project reduces the cost of harnessing the renewable energy. The system architecture includes the elliptical exercise machines outputting power to DC-DC converters, which then connects to the microinverters. All microinverter outputs tie together and then connect to the grid. The control system, placed around the DC-DC converters, quickly detects changes in current, and limits the current to prevent the DC-DC converters and microinverters from entering failure states.

An artificial neural …

Complex Filters As Cascade Of Buffered Gingell Structures: Design From Band-Pass Constraints, Nicole M. Hay

Master's Theses

Complex filters are multi-input, multi-output networks designed to discriminate based upon the relative phase difference between input signals. Complex filters find application in modern wireless systems for single sideband transmission and image-reject reception. This thesis presents one active complex filter implementation using two operational amplifiers per stage, termed “type-II” topology. The “type-II” originates from the passive RC-CR polyphase topology presented by Gingell in his 1973 paper, “Single sideband modulation using sequence asymmetric polyphase networks.” This new topology gains several advantages over existing complex filter implementations, namely “cascadability” (multiple sections placed in series to create a higher-order response) without altering the …

Cubesat Data Transmission And Storage Throughput Optimization Through The Use Of A Zynq Soc Based Cubesat Science Instrument Interface Electronics Board, Caleb Mosby Munsill

Master's Theses

The CubeSat standard sprang from the desire to create a satellite standard that would open the doors for universities and other lower budget research institutions by making it more feasible to get their work into space. Since then, many other institutions and industries have been adopting variations on the standard for their own use. As more people are seeking out to use the CubeSat standard as their main bus, the standards and practices of the community have grown and expanded and with this growth, new challenges have been created. One such challenge is the bandwidth limitation in the RF-downlink. When …

Silent Communication Device, Christopher Wayne Schutter

Master's Theses

Oral communication has constituted as a necessary aspect of how people interact with one another, but there are always situations where this form of communication can create distractions, irritation, or even danger. Take for example, a student in a laboratory who needs to communicate effectively with a lab partner without creating a distraction to those trying to work around said student or a soldier on a battlefield who needs to relay information effectively to his or her comrades without revealing his or her position to the enemy. It becomes apparent that people need a more exclusive form of communication in …

Energy Management System Modeling Of Dc Data Center With Hybrid Energy Sources Using Neural Network, Khalid Althomali

Master's Theses

As data centers continue to grow rapidly, engineers will face the greater challenge in finding ways to minimize the cost of powering data centers while improving their reliability. The continuing growth of renewable energy sources such as photovoltaics (PV) system presents an opportunity to reduce the long-term energy cost of data centers and to enhance reliability when used with utility AC power and energy storage. However, the inter-temporal and the intermittency nature of solar energy makes it necessary for the proper coordination and management of these energy sources.

This thesis proposes an energy management system in DC data center using …

Design, Analysis, And Simulation Of A Jitter Reduction Circuit (Jrc) System At 1ghz, Run Bin Yu

Master's Theses

The clock signal is considered as the “heartbeat” of a digital system yet jitter which is a variation on the arrival time of the clock edge, could undermine the overall performance or even cause failures on the system. Deterministic jitter could be reduced during the designing process however random jitter during operation is somehow less-controllable and unavoidable. Being able to remove jitter on the clock would therefore play a vital role in system performance improvement.

This thesis implements a 1GHz fully feedforward jitter reduction circuit (JRC) which can be used as an on-chip IP core at clock tree terminals to …

Scaled Synthetic Aperture Rader Development, Jason Garvey Schray

Master's Theses

Several previous Cal Poly thesis projects involve synthetic aperture radar (SAR), automatic target recognition (ATR), and tracking. SAR data was either accessed from a publicly available database or generated using complex computer modeling software. The motivation for this dual thesis project is to design and construct a scaled SAR system to support Cal Poly radar projects. Ideally this is a low-cost, high resolution SAR architecture that produces raw range Doppler data for any desired target area. To that end, a scaled SAR system was successfully designed, built, and tested. The current SAR system, however, does not perform azimuthal compression and …

Complex Filters As As A Cascade Of Of Buffered Gingell Structures: Design From From Band-Stop Constraints, Samuel Robert Johnston

Master's Theses

This thesis presents an active Complex Filter implementation that that creates a transfer function with with a single real pole and a complex zero. The two-input/two-output network developed in in this thesis responds differently based upon upon the relative phase difference of of the two inputs. If a negative ninety-degree phase difference occurs between the two inputs, the filter will exhibits a bandstop response. While a positive ninety-degree phase difference exhibits a bandpass response. This topology is relatesd to to Gingell’s RC-CR polyphase topology but because of of the use of of op-amps, can be cascadedd without without suffering loading …

Design Of An Integrated Acceleration Acquisition Subsystem To Satisfy High-Speed And Low-Area Requirements For Cubesats, Ryan J. Rumsey

Master's Theses

Cal Poly San Luis Obispo’s PolySat team is designing the Multipurpose Orbital Spring Ejection System (MOSES) in order to record acceleration data during the launch of CubeSats as well as to provide GPS coordinates to locate the position of CubeSats once they are injected into orbit. This work focuses on the design and development of the acceleration data acquisition (DAQ) subsystem of MOSES. This subsystem is designed around the need for a high-speed sampling system of at least 200 kHz across four channels of data, plus low-area limitations in the MOSES form factor which is roughly half the size of …

Design Of Inexpensive And Easy To Use Diy Internet Of Things Platform, Samuel R. Jaffe

Master's Theses

This thesis focuses on the design and implementation of a new, inexpensive, and less complex system for a Do-It-Yourself (DIY) Internet of Things (IoT) platform. The hardware aspects focus on a new chip called the ESP8266 which contains both microcontroller and WiFi connectivity capabilities in an extremely affordable package. The system uses the Arduino IDE to program the ESP8266, which is known to be an extremely user-friendly environment. All other software is both free and easy to use. Past methods of creating IoT projects involved either expensive hardware, often ranging from $50-$100 per node, or complicated programming requiring a full …

Low-Frequency Series Loaded Resonant Inverter Characterization, Alfredo Medina

Master's Theses

Modern power systems require multiple conversions between DC and AC to deliver power from renewable energy sources. Recent growth in DC loads result in increased system costs and reduced efficiency, due to redundant conversions. Advances in DC microgrid systems demonstrate superior performance by reducing conversion stages. The literature reveals practical DC microgrid systems composed of wind and solar power to replace existing fossil fuel technologies for residential consumers. Although higher efficiencies are achieved, some household appliances require AC power; thus, the need for highly efficient DC to AC converters is imperative in establishing DC microgrid systems. Resonant inverter topologies exhibit …

Hall Effect Modeling In Fem Simulators And Comparison To Experimental Results In Silicon And Printed Sensors, Leonardo A. Frem

Master's Theses

Finite element method simulation models for thin-film semiconductor-based Hall sensors were developed using secondary data in order to understand their behavior under strong magnetic fields. Given a device geometry and charge carrier density and mobility, the models accurately calculated sensor resistance, Hall voltage under a normally-incident constant magnetic field, and expected offset from a population of Hall devices. The model was successfully matched against data from integrated chip Hall sensors from St. Jude Medical. Additionally, the feasibility of creating Hall effect devices with common carbon ink was explored experimentally. The material properties obtained from testing these ink-based devices through the …

Ism S-Band Cubesat Radio Designed For The Polysat System Board, Craig Lee Francis

Master's Theses

Cal Poly’s PolySat CubeSat satellites have begun to conduct more complex and scientifically significant experiments. The large data products generated by these missions demonstrate the necessity for higher data rate communication than currently provided by the PolySat UHF radio. This thesis leverages the proliferation of consumer wireless monolithic transceivers to develop a 250kbps to 2000kbps, 2W CubeSat radio operating within the 2.45GHz Industrial, Scientific, and Medical (ISM) radio band.

Estimating a link budget for a realistic CubeSat leads to the conclusion that this system will require a large deployable CubeSat antenna, large earth station satellite dish, and a fine-pointing attitude …

Out-Of-Loop Compensation Method For Op-Amps Driving Heavy Capacitive Loads, Shubham Gandhi

Master's Theses

It is well known that real op-amps do not share most of the desirable characteristics of an ideal one, particularly those of gain and output impedance. When presented with a capacitive load, such as a MOSFET or ADC, feedback in an op-amp circuit can quickly become unstable. This thesis studies and characterizes an op-amp’s output impedance and how its interaction with this type of load creates a parasitic pole which leads to instability. Applying ideas from feedback control theory, a model for studying the problem is developed from which a generalized method for compensating the undesirable circumstance is formulated.

Even …

Oceanographic Instrument Simulator, Amy Chen

Master's Theses

The Monterey Bay Aquarium Research Institute (MBARI) established the Free Ocean Carbon Enrichment (FOCE) experiment to study the long-term effects of decreased ocean pH levels by developing in-situ platforms [1]. Deep FOCE (dpFOCE) was the first platform, which was deployed in 950 meters of water in Monterey Bay. After the conclusion of dpFOCE, MBARI developed an open source shallow water FOCE (swFOCE) platform located at around 250 meter of water to facilitate worldwide shallow water experiments on FOCE [1][2]. A shallow water platform can be more ubiquitous than a deep-water platform as shallow water instruments are less expensive (as it …

Wide-Band Gap Devices For Dc Breaker Applications, Olukayode O. Sodipe

Master's Theses

With the increasing interest in wide-band gap devices, their potential benefits in power applications have been studied and explored with numerous studies conducted for both SiC and GaN devices. This thesis investigates the use of wide-band gap devices as the switching element in a semiconductor DC breaker. It involves the design of an efficient semiconductor DC breaker, its simulation in SPICE, construction of a hardware prototype and the comparative study of SiC and Si versions of the aforementioned breaker. The results obtained from the experiments conducted in the process of concluding this thesis show that the SiC version of the …

Scaled Synthetic Aperture Radar System Development, Ryan K. Green

Master's Theses

Synthetic Aperture Radar (SAR) systems generate two dimensional images of a target area using RF energy as opposed to light waves used by cameras. When cloud cover or other optical obstructions prevent camera imaging over a target area, SAR can be substituted to generate high resolution images. Linear frequency modulated signals are transmitted and received while a moving imaging platform traverses a target area to develop high resolution images through modern digital signal processing (DSP) techniques. The motivation for this joint thesis project is to design and construct a scaled SAR system to support Cal Poly radar projects. Objectives include …

Stability Analysis Of Negative Resistance-Based Source Combining Power Amplifiers, Hannah S. Homer

Master's Theses

An investigation into the stability of negative resistance-based source combining power amplifiers is conducted in this thesis. Two different negative resistance-based source combining topologies, a series and parallel version, are considered. Stability is analyzed using a simple and intuitive broadband approach that leverages linear circuit stability criterion and two different linearization methods: linearization around the operating point and in the frequency domain. Using this strategy, it is shown that conditions for self-sustained oscillation exist for both topologies. For the series combining topology, self-sustained oscillation is prevented by means of injection locking.

Adaptive Automotive Lighting Systems, Marc W. Haeberlin

Master's Theses

Over the past few years, the use of LEDs within the automotive and avionic industries has increased due to their high efficiency, durability and wide range of light brightness. As the use of LEDs within these industries grows, a need for reliable, high performance drivers becomes more relevant. Companies are implementing LEDs for applications involving adaptive lighting or simple dimming features. This thesis shows implementation of various non-isolated analog converters integrated with digital dimmers to achieve these adaptive lighting systems. Adaptive lighting systems involve reading an input from an external source (brake pedal or steering wheel) and changing the brightness …

Design And Fabrication Techniques Of Devices For Embedded Power Active Contact Lens, Errol Heradio Leon

Master's Theses

This thesis designed and fabricated various devices that were interfaced to an IC for an active contact lens that notifies the user of an event by detection of an external wireless signal. The contact lens consisted of an embedded antenna providing communication with a 2.4GHz system, as well as inductive charging at an operating frequency of 13.56 MHz. The lens utilized a CBC005 5µAh thin film battery by Cymbet and a manufactured graphene super capacitor as a power source. The custom integrated circuit (IC) was designed using the On Semiconductor CMOS C5 0.6 µm process to manage …