Electrical and Electronics Commons^™

Integration Of Electrical Impedance Spectroscopy For Multichannel Cell Culture Measurement, Conard Chan

Master's Theses

ELECTROCHEMICAL IMPEDANCE SPECTROSCOPY (EIS) has been widely used to study the electrical properties of biological material due to its non-invasive nature and experimental reliability. However, most of the precision impedance analyzers used in EIS only provide single- or two-channel measurements which are inadequate for larger-scale multiplexed measurements, such as those found in modern microfluidic cell culture experiments. The Biomedical Microsystems Laboratory has developed a 16-channel cell culture platform with integrated electrode arrays for monitoring cell growth and electrical properties (i.e., the so-called “electrical phenotype”). In this paper, a system consisting of a 16-channel solid-state analog multiplexer (MUX)paired with a low-cost, …

Indoor Positioning Using Synchronized Ultrasonic Ofdma Signals, Julian Bartolone

Master's Theses

This paper proposes a method of short-range indoor localization using differential phase measurements of synchronized two-tone ultrasonic signals in an Orthogonal Frequency Multiple Access (OFDMA) scheme. This indoor positioning system (IPS) operates at an ultrasonic frequency of approximately 40kHz and synchronizes using an infrared signal. The OFDMA scheme allows for a receiver to process the signals from multiple transmitters continuously without the signals interfering with each other. The phases of the signals are measured using Goertzel Filters, allowing for low-complexity frequency content analysis. A MATLAB simulation using the proposed localization method is performed using four transmitter nodes in the corners …

Printed Circuit Board Design And Layout For Hobbyists, Engineers, And Students, Michael A. Derrenbacher

Master's Theses

Printed Circuit Boards (PCBs) are a ubiquitous element of virtually every electronic system manufactured world-wide. It is not a stretch of the imagination to say that if it’s electronic, there is a PCB in it. PCBs are necessary tools for electronics work, and tools need to have instructions. For better or worse, PCB knowledge is a deep and wide ocean. There is much to cover for even a surface level understanding, and there are deep areas rich in technical expertise. Navigating the ocean of knowledge is treacherous; common knowledge of yore can be downright dubious now. PCB manufacturing and electronics …

High Voltage Dc-Dc Converter Design For Submarine Application, Oscar Ambriz

Master's Theses

In this work a proof of concept for a step-down DC-DC converter used in a high voltage submarine application is presented. The purpose of the converter is to step down a 5000V-6000V input to a 24V output which can serve as an input to a submarine sensor. The completed system consists of two stages where the first stage is an unregulated switched capacitor converter to step down the initial input to a voltage range more appropriate for the selected second stage. The second stage is a regulated flyback converter topology which regulates the final output to the desired 24V. Performance …

Zero Voltage Switching Hybrid Voltage Divider Converter, Timothy Jeong

Master's Theses

This project proposes a new hybrid voltage divider DC-DC converter that utilizes switching capacitors and inductors to produce zero voltage switching (ZVS) at the turn on state of its switches. By achieving ZVS, the switching losses are significantly reduced; thus, increasing the overall efficiency of the converter at various loads. The goal for this thesis is to perform analysis of the operation of the converter, derive equations for sizing the main components, and demonstrate its functionality through computer simulation and hardware prototype. Results of the simulation and hardware testing show that the proposed converter produces the desired output voltage while …

First Order Self-Oscillating Class-D Circuit With Triangular Wave Injection, Matthew J. Carroll

Master's Theses

An investigation into performance improvements to the modulator stage of a class-D amplifier is conducted in this thesis. Two of the standard topologies, namely class-D open-loop pulse-width modulation (PWM), and the improved self-oscillating feedback system are benchmarked against a topology which includes both a hysteretic comparator in a feedback loop and triangle wave injection. Circuit performance is analyzed by comparing how the triangle injection circuit handles known issues with open-loop and self-oscillating circuits. Using this analysis, it is shown that the triangle injection topology offers an improved power supply rejection ratio relative to open-loop PWM and reduces distortion generated by …

Design And Modeling Of A Distributed Network For The Dc House Project, Lauren N. Rotsios

Master's Theses

This thesis covers the design and simulation of a model for a distributed network of DC Houses in MATLAB Simulink. The model will allow for sharing of power between houses within the network. The developed model consists of five separate DC House branches with local power generation. Each branch consists of a PV MPPT charge controller subsystem, a resistive load, and a bidirectional buck-boost converter subsystem. The high voltage side of every bidirectional buck-boost converter is connected together through the transmission line at a single high voltage DC bus. The performance of the individual components of the model is verified …

Scalable Cognitive Radio Network Testbed In Real Time, Kevin Z. Yu

Master's Theses

Modern society places an increasingly high demand on data transmission. Much of that data transmission takes place through communication over the frequency spectrum. The channels on the spectrum are limited resources. Researchers realize that at certain times of day some channels are overloaded, while others are not being fully utilized. A spectrum management system may be beneficial to remedy this efficiency issue. One of the proposed systems, Cognitive Radio Network (CRN), has progressed over the years thanks to studies on a wide range of subjects, including geolocation, data throughput rate, and channel handoff selection algorithm, which provide fundamental support for …

Design And Characterization Of Standard Cell Library Using Finfets, Phanindra Datta Sadhu

Master's Theses

The processors and digital circuits designed today contain billions of transistors on a small piece of silicon. As devices are becoming smaller, slimmer, faster, and more efficient, the transistors also have to keep up with the demands and needs of the daily user. Unfortunately, the CMOS technology has reached its limit and cannot be used to scale down due to the transistor's breakdown caused by short channel effects. An alternative solution to this is the FinFET transistor technology, where the gate of the transistor is a three dimensional fin that surrounds the transistor and prevents the breakdown caused by scaling …

Development Of A Portable Low-Moisture Food Pasteurization Device Using Rf Heating, Eric Jason Ohata

Master's Theses

Bacterial presence in low-moisture foods such as flour, cereals, baby formula, and spices, have become a concern due to sanitizing challenges. The food industry currently focuses on wet food sanitation as opposed to low-moisture foods because of bacteria’s inability to reproduce in low water activity media. Traditionally, food processing RF heating pasteurizes in mass quantities while an equivalent consumer device does not exist the market today. A consumer product would help eliminate food waste by providing an easy way to sanitize food and extend shelf life. The Portable Food Pasteurization (PFP) project is an interdisciplinary project involving the Electrical Engineering, …

Neural Network For Monitoring Infant Feeding Process In The Smartbottle Device, Jiajun Guan

Master's Theses

To research the relationship between Childhood obesity and infant feeding patterns, the Electrical Engineering Department at California Polytechnic State University has designed a SmartBottle device attaching to the bottom of a baby bottle to monitor the infant feeding process. This project mainly focuses on the software and firmware design, as well as the neural network design of the SmartBottle device. The SmartBottle device is designed to identify infant feeding activities and to record related data for overweight and obesity research on children. This device includes a 6-dimensional inertial sensor that contains a 3-axis digital accelerometer and a 3-axis digital gyroscope. …

Design Of An Ultra-Wideband Frequency-Modulated Continuous Wave Short Range Radar System For Extending Independent Living, Toai-Chi Nguyen

Master's Theses

Falls in the disabled and elderly people have been a cause of concern as they can be immobilized by the fall and have no way to contact others and seek assistance. The proposed frequency modulated continuous wave (FMCW) short range radar (SRR) system, which uses ultra-wideband (UWB) signals can provide immediate assistance by monitoring and detecting fall events. The unique characteristics of this system allow for a frequency-based modulation system to carry out triangulation and sense the location of the fall through the usage of a continuous chirp signal that linearly sweeps frequency. This project focuses on the development, design …

Controller Modeling And Stability Analysis Of Multiple Input Single Output Dc-Dc Converter, Astha Adhikari

Master's Theses

This thesis entails the stability analysis of the Multiple Input Single Output (MISO) DC-DC converter developed for the DC House Project at Cal Poly. A frequency domain control system model of the MISO converter was designed and constructed using MATLAB Simulink. Transfer functions were derived and modeled for each stage of the converter to best fit the converter circuit system used in the original MISO circuit. Stability metrics such as overshoot, undershoot, rise time, phase margin and gain margin were measured to evaluate and analyze the stability of the converter. These metrics were measured with the original model including the …

Early Wildfire Detection With Line Sensors, Virginia Yan

Master's Theses

Over the last few years, wildfires have become more devastating to communities as the fires are inevitably destructive to many homes, businesses, and ecosystems. Frequent wildfires also pose a significant threat to power grids and nearby residents as they can damage transmission lines and other electrical equipment, which in turn can cause major power shutdowns. Especially in western U.S., severe drought conditions and weather variability cause residents to become more vulnerable to wildfire disasters as their safety is threatened. We are incompetent to control the wildfires effectively despite existing advanced technologies. Hence, an algorithm based on energy conservation and heat …

Iot Camera System For Monitoring Strawberry Fields, Simon Schoennauer

Master's Theses

A wireless imaging system for monitoring strawberry fields provides enough quality image data for computer vision algorithms to make meaningful yield predictions. This report contains a design for a wireless sensor network modified with mesh networking techniques to extend coverage range and a solar energy harvesting system to improve sensor node lifetime. A two hop system with six nodes is implemented in a laboratory environment validating the communication systems integrity over an 800’ range. Moving from a primary battery system to solar energy harvesting increases the module lifetime indefinitely.

Simulation Of An Sp8t 18 Ghz Rf Switch Using Smt Pin Diodes, Andre De Souza Vigano

Master's Theses

Radio frequency (RF) and microwave switches are widely used in several different applications including radar, measurement systems, telecommunications, and other areas. An RF switch can control a radar’s transmit vs. receive mode, select the operating band, or direct an RF signal to different paths. In this study, a single pole eight throw (SP8T) switch using only Surface Mount (SMT) components is designed and simulated in Keysight’s Advanced Design System (ADS). Single pole eight throw is defined as one input and eight possible outputs. A star network configuration with series-shunt PIN diode switches is used to create the 8-way RF switch. …

Distance Estimation Using Ofdm Signals For Ultrasonic Positioning, Kyman Huang

Master's Theses

This paper describes a method of estimating distance via Time-of-Flight (TOF) measurement using ultrasonic Orthogonal Frequency Division Multiplexing (OFDM) signals. Using OFDM signals allows the signals and their sub-carriers to remain orthogonal to each other while continuously transmitting. This estimation method is based on the change of phase of a traveling wave as it propagates through a medium (air for ultrasonic signals). By using signals containing multiple tones, the phase change between each frequency component is slightly different. This phase difference is dependent on the distance traveled and can thus be used to estimate distance. This paper studies the impact …

The Design, Testing, And Analysis Of A Constant Jammer For The Bluetooth Low Energy (Ble) Wireless Communication Protocol, Aiku Shintani

Master's Theses

The decreasing cost of web-enabled smart devices utilizing embedded processors, sensors, and wireless communication hardware have created an optimal ecosystem for the Internet of Things (IoT). IEEE802.15.4, IEEE802.11ah, WirelessHART, ZigBee Smart Energy, Bluetooth (BT), and Bluetooth Low Energy (BLE) are amongst the most commonly used wireless standards for IoT systems. Each of these standards has tradeoffs concerning power consumption, range of communication, network formation, security, reliability, and ease of implementation. The most widely used standards for IoT are Bluetooth, BLE, and Zigbee. This paper discusses the vulnerabilities in the implementation of the PHY and link layers of BLE. The link …

A Novel Arc Welding Power Supply With Improved Power Factor Correction, Benjamin H. Tan

Master's Theses

This paper presents the design and development of a novel Arc Welding Power Supply utilizing a modified two-switch forward converter topology. The proposed design improves the power quality by improving power factor to near unity and reducing total harmonic distortion. State space analysis of the proposed circuit showed that the circuit followed a boost-buck input output relationship. Simulation of the circuit was first implemented in LTspice to verify the functionality of the new topology. Hardware implementation of the proposed design was built on a scaled-down prototype for a proof-of-concept of the new topology. The prototype specifications were created for a …

Design, Modeling And Control Of A Two-Wheel Balancing Robot Driven By Bldc Motors, Charles T. Refvem

Master's Theses

The focus of this document is on the design, modeling, and control of a self-balancing two wheel robot, hereafter referred to as the balance bot, driven by independent brushless DC (BLDC) motors. The balance bot frame is composed of stacked layers allowing a lightweight, modular, and rigid mechanical design. The robot is actuated by a pair of brushless DC motors equipped with Hall effect sensors and encoders allowing determination of the angle and angular velocity of each wheel. Absolute orientation measurement is accomplished using a full 9-axis IMU consisting of a 3-axis gyroscope, a 3-axis accelerometer, and a 3-axis magnetometer. …

Performance Enhancement And Characterization Of An Electromagnetic Railgun, Paul M. Gilles

Master's Theses

Collision with orbital debris poses a serious threat to spacecraft and astronauts. Hypervelocity impacts resulting from collisions mean that objects with a mass less than 1g can cause mission-ending damage to spacecraft. A means of shielding spacecraft against collisions is necessary. A means of testing candidate shielding methods for their efficacy in mitigating hypervelocity impacts is therefore also necessary. Cal Poly’s Electromagnetic Railgun was designed with the goal of creating a laboratory system capable of simulating hypervelocity (≥ 3 km/s) impacts. Due to several factors, the system was not previously capable of high-velocity (≥ 1 km/s) tests. A deficient projectile …

Multiple Input, Single Output Dc-Dc Conversion Stage For Dc House, Jason Baltierrez

Master's Theses

n this thesis project, a proposed architecture for the multiple input, single output conversion stage for the DC House was designed, simulated, and tested. This architecture allows for multiple different input sources to be used to create a single higher power output source. The design uses a DC-DC boost converter with a parallelable output which has been demonstrated to allow increased total output power as a function of the number of input sources available. The parallelable output has been shown to distribute load amongst the input sources relatively closely to optimize the system. This approach is also desirable since it …

Smart Dc Wall Outlet Design With Improved Load Voltage Detection, Patrick Donovon Granieri

Master's Theses

A standard home in the United States has access to the 120V AC power grid for use with home appliances. Many electronics used at home are powered by a DC power supply, which loses energy in the conversion from AC power. The DC House project avoids any conversion between AC and DC by storing energy in batteries as DC power and supplying it directly to DC appliances. While AC systems feature a standardized output voltage, no such standard exists for DC systems. The Smart DC Wall Outlet solves this by automatically adjusting its output voltage to meet any required DC …

Designing A Simulator For An Electrically-Pumped Organic Laser Diode, Robert Hulbert

Master's Theses

Organic semiconductors provide an alternative set of basis materials to fabricate electronic devices like PN Junctions, LEDs, and FETs. These materials have several benefits over traditional inorganic semiconductors including their mechanical flexibility, reliance on renewable resources, and inexpensive large-scale manufacturability. Despite the contemporary device implementations with organic semiconductors, a solid-state electrically-pumped organic laser diode does not exist. However, organically-based lasers do exist by utilizing the organic material strictly for optical gain. The challenge occurs when charge carriers appear in the organic material. The charge carriers must reach a concentration such that population inversion occurs producing optical gain. However, between the …

Analog Single Sideband-Pulse Width Modulation Processor For Parametric Acoustic Arrays, Vikrant A. Marathe

Master's Theses

Parametric acoustic arrays are ultrasonic-based loudspeakers that produce highly directive audio. The audio must first be preprocessed and modulated into an ultrasonic carrier before being emitted into the air, where it will self-demodulate in the far field. The resulting audio wave is proportional to the double time-derivative of the square of the modulation envelope. This thesis presents a fully analog processor which encodes the audio into two Pulse Width Modulated (PWM) signals in quadrature phase and sums them together to produce a Single Sideband (SSB) spectrum around the fundamental frequency of the PWM signals. The two signals are modulated between …

Cmos Design Of An 8-Bit 1ms/S Successive Approximation Register Adc, Ameya Vivekanand Ganguli

Master's Theses

Rapid evolution of integrated circuit technologies has paved a way to develop smaller and energy efficient biomedical devices which has put stringent requirements on data acquisition systems. These implantable devices are compact and have a very small footprint. Once implanted these devices need to rely on non-rechargeable batteries to sustain a life span of up to 10 years. Analog-to-digital converters (ADCs) are key components in these power limited systems. Therefore, development of ADCs with medium resolution (8-10 bits) and sampling rate (1 MHz) have been of great importance.

This thesis presents an 8-bit successive approximation register (SAR) ADC incorporating an …

Surface Engineering Solutions For Immersion Phase Change Cooling Of Electronics, Brendon M. Doran

Master's Theses

Micro- and nano-scale surface modifications have been a subject of great interest for enhancing the pool boiling heat transfer performance of immersion cooling systems due to their ability to augment surface area, improve wickability, and increase nucleation site density. However, many of the surface modification technologies that have been previously demonstrated show a lack of evidence concerning scalability for use at an industrial level. In this work, the pool boiling heat transfer performance of nanoporous anodic aluminum oxide (AAO) films, copper oxide (CuO) nanostructure coatings, and 1D roll-molded microfin arrays has been studied. Each of these technologies possess scalability in …

Ac Direct Drive Led Lighting Using Low Cost Analog Components, Miles Head

Master's Theses

This project explores the rapidly expanding area of AC direct drive for LED lighting. AC LED driving does not use typical DC-DC converter-based driving but uses semiconductor switches and a linear regulator to activate a number of LEDs proportional to the input voltage at any given time. This allows bulky, expensive magnetics to be eliminated from the system. The goal of this project was to design a scaled-down physical AC LED direct drive system to validate the conclusions of methods for improving efficiency from a previous investigation that found minimizing voltage across the linear regulating MOSFET led to higher efficiency …

Design Of A Low-Cost Data Acquisition System For Rotordynamic Data Collection, Gregory S. Pellegrino

Master's Theses

A data acquisition system (DAQ) was designed based on the use of a STM32 microcontroller. Its purpose is to provide a transparent and low-cost alternative to commercially available DAQs, providing educators a means to teach students about the process through which data are collected as well as the uses of collected data. The DAQ was designed to collect data from rotating machinery spinning at a speed up to 10,000 RPM and send this data to a computer through a USB 2.0 full-speed connection. Multitasking code was written for the DAQ to allow for data to be simultaneously collected and transferred …

Experimental Optical Pulse Picker For Lawrence Livermore National Lab, Alexander Thomas Wargo

Master's Theses

Proprietary.