Electrical and Electronics Commons^™

The Development Of A High-Performance Distributed Battery Management System For Large Lithium Ion Packs, Christopher B. Grasberger

Master's Theses

A high performance battery management system (BMS) for large capacity cells was designed, built, and tested in a cycle of three revisions. The BMS was designed for use in applications where the battery pack configuration is unknown: parallel, series, or any combination. Each of the cells is equipped with its own battery management system to allow a peer-to-peer mesh network to monitor the safety of the cell. The BMS attached to each cell also is equipped with a 25A DC/DC converter to perform active balancing between cells in a string. This converter can transfer charge to (or from) a cell …

Universal Programmable Battery Charger With Optional Battery Management System, Michael Duke Desando

Master's Theses

This report demonstrates improvements made in battery charging and battery management technology through the design of a universal programmable battery charger with optional battery management system attachment. This charger offers improvements in charge efficiency and unique battery charging algorithms to charge a variety of battery chemistries with variety of power requirements. Improvements in efficiency result from a synchronous Buck Controller topology as compared to previous universal chargers that use asynchronous Buck-Boost Converter topologies. This battery charger also surpasses current universal battery chargers by offering different charge modes for different battery chemistries. Charge modes provide the user an option between extending …

Three-Phase Generation Using Reactive Networks, Tattiana Karina Coleman Davenport

Master's Theses

Household appliances utilize single-phase motors to perform everyday jobs whether it is to run a fan in an air conditioner or the compressor in a refrigerator. With the movement of the world going “green” and trying to make everything more efficient, it is a logical step to start with the items that we use every day. This can be done by replacing single-phase motors with three-phase motors in household appliances. Three-phase motors are 14% more efficient than single-phase motors when running at full load and typically cost less over a large range of sizes [1]. One major downside of incorporating …

Digitally Controlled Zero-Voltage-Switching Quasi-Resonant Buck Converter, Brian R. Luc

Master's Theses

ABSTRACT

Digitally-Controlled Two-Phase Zero-Voltage-Switching Quasi-Resonant Buck Converter

Brian Luc

This thesis entails the design, construction, and performance analysis of a digitally-controlled two-phase Zero-Voltage Switching Quasi-Resonant (ZVS-QR) buck converter. The converter is aimed to address the issues associated with powering CPUs operating at lower voltage and high current. To evaluate its performance, the Two-Phase ZVS-QR buck converter is compared against a traditional Two-Phase buck converter. The design procedure required to implement both converters through utilizing the characterization curve and formulas derived from their circuit configurations will be presented. Computer simulation of the Two-Phase ZVS-QR buck converter is provided to exhibit its …

A Low-Cost Loop Measurement Tool For Dc-Dc Converters, Shouee B. Lin

Master's Theses

Loop measurements are very important in evaluating dynamic performance of DC-DC converters. In this thesis, a small loop measurement tool as a low-cost alternative to a network analyzer is proposed. The tool is particularly useful when a network analyzer is not always available for use, for example when engineers are working on-site with customers or when a network analyzer is not affordable due to their relatively high cost. The design, simulation, and hardware implementation of the inexpensive loop measurement tool will be presented in this thesis. Results from computer simulation and hardware prototype demonstrate the ability of the proposed tool …

Hybrid Silicon Mode-Locked Laser With Improved Rf Power By Impedance Matching, Bassem M. Tossoun

Master's Theses

The mode-locked laser diode (MLLD) finds a lot of use in applications such as ultra high-speed data processing and sampling, large-capacity optical fiber communications based on optical time-division multiplexing (OTDM) systems. Integrating mode-locked lasers on silicon makes way for highly integrated silicon based photonic communication devices. The mode-locked laser being used in this thesis was built with Hybrid Silicon technology. This technology, developed by UC Santa Barbara in 2006, introduced the idea of wafer bonding a crystalline III- V layer to a Silicon-on-insulator (SOI) substrate, making integrated lasers in silicon chips possible.

Furthermore, all mode-locked lasers produce phase noise, which …

Smart Wall Outlet Design And Implementation For The Dc House Project, Kevin Roy Mendoza

Master's Theses

Most everyday AC appliances are designed to operate off of 120V coming from the wall outlet in our homes. This voltage is a standard set from our established infrastructure. Unlike AC devices, DC devices do not have any set standard of voltage they all will run off of. This presents a problem for the DC house as the various loads that will be used will have different required input voltages. One set voltage for a wall outlet will not suffice for the DC House. This Smart Wall Outlet is designed with a DC-DC converter that will have its output voltage …

Dual High-Voltage Power Supply For Use On Board A Cubesat, Nicholas Weiser

Master's Theses

Since their conception in 1999, CubeSats have come and gone a long way. The first few that went into space were more of a “proof of concept,” and were more focused on sending simple data and photographs back to Earth. Since then, vast improvements have been made by over 40 universities and private firms, and now CubeSats are beginning to look towards interplanetary travel. These small satellites could provide a cost effective means of exploring the galaxy, using off the shelf components and piggy-backing on other launch vehicles with more expensive payloads. However, CubeSats are traditionally launched into Low Earth …

Improvements To A Bi-Directional Flyback Dc-Dc Converter For Battery System Of The Dc House Project, Michael Wu

Master's Theses

The DC House project relies primarily on renewable energy sources to provide DC power to the various loads of the house. However, not all renewable sources are capable of providing power at all times of the day. A back-up energy source in the form of a battery storage system must be available to meet the electrical needs of the house. A bi-directional flyback power converter was initially designed to allow a battery to charge from as well as discharge to the 48V bus line of the DC House. The design provided a 35W prototype to demonstrate the converter’s feasibility. Further …

Ac Power Combining Strategy With Application To Efficient Linear Power Amplifiers, Rudi Matthew Bendig

Master's Theses

With the ongoing push for wireless systems to accommodate more users and support higher data rates more efficient modulation schemes have been created that are more advanced than simple FM and AM modulation used for radio broadcasting. These modulation schemes, such as orthogonal frequency division multiplexing (OFDM), suffer from high peak to average power ratios. Standard Class A and Class AB amplifiers cannot simultaneously achieve good linearity and efficiency, and therefore there has been an increase in the development of new topologies to combat this issue. Common features to these circuits is power combining of two or more separate transistors. …

Variable Precision Tandem Analog-To-Digital Converter (Adc), Colton A. Parsons

Master's Theses

This paper describes an analog-to-digital signal converter which varies its precision as a function of input slew rate (maximum signal rate of change), in order to best follow the input in real time. It uses Flash and Successive Approximation (SAR) conversion techniques in sequence.

As part of the design, the concept of "total real-time optimization" is explored, where any delay at all is treated as an error (Error = Delay * Signal Slew Rate). This error metric is proposed for use in digital control systems. The ADC uses a 4-bit Flash converter in tandem with SAR logic that has variable …

Mos Current Mode Logic (Mcml) Analysis For Quiet Digital Circuitry And Creation Of A Standard Cell Library For Reducing The Development Time Of Mixed Signal Chips, David Marusiak

Master's Theses

Many modern digital systems use forms of CMOS logical implementation due to the straight forward design nature of CMOS logic and minimal device area since CMOS uses fewer transistors than other logic families. To achieve high-performance requirements in mixed-signal chip development and quiet, noiseless circuitry, this thesis provides an alternative toCMOSin the form of MOS Current Mode Logic (MCML). MCML dissipates constant current and does not produce noise during value changing in a circuit CMOS circuits do. CMOS logical networks switch during clock ticks and with every device switching, noise is created on the supply and ground to deal with …

Investigation Of Degradation Effects Due To Gate Stress In Gan-On-Si High Electron Mobility Transistors Through Analysis Of Low Frequency Noise, Michael Curtis Meyer Masuda

Master's Theses

Gallium Nitride (GaN) high electron mobility transistors (HEMT) have superior performance characteristics compared to Silicon (Si) and Gallium Arsenide (GaAs) based transistors. GaN is a wide bandgap semiconductor which allows it to operate at higher breakdown voltages and power. Unlike traditional semiconductor devices, the GaN HEMT channel region is undoped and relies on the piezoelectric effect created at the GaN and Aluminum Gallium Nitride (AlGaN) heterojunction to create a conduction channel in the form of a quantum well known as the two dimensional electron gas (2DEG). Because the GaN HEMTs are undoped, these devices have higher electron mobility crucial for …

High Voltage Pulse Measurement System, Angelo J. Ballungay

Master's Theses

Using isolation and noise immunity techniques, this thesis designs and constructs a low cost measurement system to safely and accurately measure high voltage, high frequency pulses in harsh EM environments. High voltage pulses apply to medical, plasma, and food industries. The difficulty of accurately measuring high voltage pulses continues to pose an issue. Measuring high voltage systems can cause damage to the system, the measurement system, and the user. High voltage and high frequency pulses create a harsh environment of electromagnetic fields that can disrupt the circuitry of the measurement system and harm the user. Implementing isolation from the high …

Design Of A Low Power Cargo Security Device Using A Micropower Ultra-Wideband Impulse Radar, Brian M. Wihl

Master's Theses

Each year, thousands of cargo containers are broken into during shipping, costing billions of dollars in lost and damaged goods. In addition to removing its contents, intruders can also add unwanted and dangerous materials to a container, posing a threat to National Security. The possibilities of cargo container break-ins require that the containers go through check points at which they are physically searched. These searches often require the opening of the container, unloading and inspecting all cargo, and then loading the container and resealing it. This is a long and costly process.

Because of the high costs of break-ins and …

Digital Control Board For Phased Array Antenna Beam Steering In Adaptive Communication Applications, Mayur Bansal

Master's Theses

The application of adaptive communication techniques for mobile communications has attracted considerable interest in the last decade. One example of these techniques is spatial filtering through planar antenna array beam forming.

This thesis describes the development of a digital system that adaptively controls a phased array antenna. The radiating structure of the phased antenna array is tetrahedral-shaped and contains four antenna elements on each of its three faces. The overall system comprises of a digital control board with an external computer interface, an RF control board, and the phased antenna array. The RF controls the main lobe direction on the …

A Compact, Reconfigurable Uhf Communication System Design For Use With Polysat's Embedded Linux Platform, Austin Williams

Master's Theses

The beginning of this thesis provides an overview of the heritage UHF Communication System design flown on CP2, CP3, CP4, CP5, and CP6, summarizing previous analysis of its performance, and providing the justification for a complete system re-design. High level requirements for the new UHF System are defined, and a trade study is performed on state-of-the-art single chip transceivers, low noise amplifiers, and transmit power amplifiers. These components are then designed into a functional communication system, with key components analyzed for proper impedance matching and performance characterization compared to expected datasheet values. Next, the system as a whole is characterized …

The Bicycle-Powered Smartphone Charger, Chris Arntzen

Master's Theses

This thesis entails the design and fabrication of a smartphone charger that is powered by a bicycle dynamo hub. In addition to the design and validation of the charger prototype, this thesis involves the testing and characterization of the dynamo hub power source, the design and construction of specialized test equipment, and the design and prototyping of a handlebar-mounted case for the smartphone and charging electronics. With the intention of making the device a commercial product, price, aesthetics, and marketability are of importance to the design. An appropriate description of the charger circuit is a microcontroller-based energy management system, tailored …

Bi-Directional Flyback Dc-Dc Converter For Battery System Of The Dc House Project, Austin J. Luan

Master's Theses

The DC House project strongly relies on renewable energy sources to provide power to the house for various loads. However, when these sources are unable to provide power at a certain time, a back-up energy source from a battery must be readily available to fulfill the house’s power needs. This thesis proposes a bi-directional flyback power converter to allow a single-stage power path to charge the battery from and to discharge the battery to the DC House 48 V system bus. The design, simulation, and hardware prototype of the proposed flyback bi-directional converter will be conducted to demonstrate its feasibility. …

Eye "R" Glasses: Development Of An Infrared Sensor System For Detecting The Human Body, Rick Wong

Master's Theses

Throughout the years, sensors have been an integral part of automation, alert, and medical systems. Many of these systems measure physiological characteristics of the human body to alert themselves of their current conditions. Drowsy driver systems, for instance, measure the eyes and facial movements with a camera to determine if the driver is falling asleep at the wheel. Electroencephalography (EEG), electrooculography (EOG), and electromyography (EMG) employ electrodes on the human body to measure electrical activity of a patient’s REM sleep cycle patterns. Pulse oximeters use optical light through a process called photoplethysmography (PPG) to measure heart rate.

As diverse as …

A Novel Unit Cell Antenna For Highly Integrated Phased Arrays In The Shf Band, Timothy Bryan Ogilvie

Master's Theses

Phased arrays are electromagnetic antenna systems comprised of many radiating elements and processing electronics. Radiating elements are typically positioned in an orderly grid within the antenna aperture. In the receive mode of operation, radiating elements capture some of the signal energy from incoming radiation and guide these signals to processing electronics. Signals are filtered and amplified to maintain the desired sensitivity and complexly weighted using circuits with reconfigurable amplification gain and phase delay. Finally, all signals are combined. The summation of these complexly weighted spatial samples forms a spatial filter in the same way complexly weighted temporal samples establish a …

Multiple Input Single Output (Miso) Tablet/ Phone Charger, Kevin Wong

Master's Theses

This thesis entails the design and implementation of a multiple input single output (MISO) DC-DC converter using the flyback topology to charge tablets/ smartphones or any USB powered portable device. The MISO converter will enable the use of various renewable energy sources such as a solar panel/ rechargeable battery combination, bicycle dynamo, hydroelectric power, and wind turbine. This paper will cover the design, simulations, and test results of the MISO converter. The flyback topology was chosen due to its low part count and its efficiency at low power. The proposed converter has a nominal 12V input to output USB 2.0 …

Design, Fabrication, And Testing Of An Emr Based Orbital Debris Impact Testing Platform, Jeffrey J. Maniglia Jr.

Master's Theses

This paper describes the changes made from Cal Poly’s initial railgun system, the Mk. 1 railgun, to the Mk. 1.1 system, as well as the design, fabrication, and testing of a newer and larger Mk. 2 railgun system. The Mk. 1.1 system is developed as a more efficient alteration of the original Mk. 1 system, but is found to be defective due to hardware deficiencies and failure, as well as unforeseen efficiency losses. A Mk. 2 system is developed and built around donated hardware from the Naval Postgraduate School. The Mk. 2 system strove to implement an efficient, augmented, electromagnetic …

Modeling And Analysis Of A Dynamic Voltage Regulator, Timothy David Haskell

Master's Theses

Increased government funding and incentives in recent years has led to an increase in the number of grid-tied renewable energy sources as their economic benefits become more renowned. Unfortunately, the outputs of these renewable resources are often highly variable, resulting in undesirable voltage disruptions that are harmful to sensitive loads. In addition to the energy variability of renewable energy sources, random voltage sags, swells and disruptions are already a major issue in power systems. Recent advances in power electronic devices have provided a platform for new solutions to the voltage support problem in power systems. One promising solution is the …

Dc, Rf, And Thermal Characterization Of High Electric Field Induced Degradation Mechanisms In Gan-On-Si High Electron Mobility Transistors, Matthew Anthony Bloom

Master's Theses

Gallium Nitride (GaN) high electron mobility transistors (HEMTs) are becoming increasingly popular in power amplifier systems as an alternative to bulkier vacuum tube technologies. GaN offers advantages over other III-V semiconductor heterostructures such as a large bandgap energy, a low dielectric constant, and a high critical breakdown field. The aforementioned qualities make GaN a prime candidate for high-power and radiation-hardened applications using a smaller form-factor. Several different types of semiconductor substrates have been considered for their thermal properties and cost-effectiveness, and Silicon (Si) has been of increasing interest due to a balance between both factors.

In this thesis, the DC, …

Smart Wall Plug Design For The Dc House Project, Edward Constant Sibal

Master's Theses

The DC House project at Cal Poly State University faces a challenge of supplying DC voltage to household appliances. Each appliance in the DC House constitutes a DC load that has a unique voltage and power rating, hence the need to develop a smart DC wall plug that will automatically adjust to the operating voltage required by any DC load. This thesis entails a proof of concept design of the smart DC wall plug which can automatically detect an appliance’s voltage rating. The design employs a dc-dc converter in conjunction with a microcontroller to sense load current to properly adjust …

Fabrication And Characterization Of Torsional Micro-Hinge Structures, Mike Madrid Marrujo

Master's Theses

ABSTRACT

Fabrication and Characterization of Torsional Micro-Hinge Structures

Mike Marrujo

There are many electronic devices that operate on the micrometer-scale such as Digital Micro-Mirror Devices (DMD). Micro actuators are a common type of DMD that employ a diaphragm supported by torsional hinges, which deform during actuation and are critical for the devices to have high stability and reliability. The stress developed within the hinge during actuation controls how the actuator will respond to the actuating force. Electrostatically driven micro actuators observe to have a fully recoverable non-linear viscoelastic response. The device consists of a micro-hinge which is suspended by two …

Energy Harvesting From Elliptical Machines: Dc-Dc Converter Design Using Sepic Topology, Martin Kou

Master's Theses

Cal Poly’s ongoing Energy Harvesting from Exercise Machines (EHFEM) project is a very convenient and cost-effective way for generating DC power from physical exercise and sending it back to the electrical grid as AC power, providing a renewable energy source for the future. The EHFEM project consists of numerous subprojects involving converting different types of exercise machines for power generation. This project is a continuation of one of the previous subprojects, specifically involving an elliptical machine, and focuses on improving system functionality at different machine settings without altering the elliptical user’s experience by selecting a new DC-DC converter design, while …

Cascaded High Voltage Converter With Variable Control For Pulsed Electric Field Applications, Emmanuel Loza

Master's Theses

Living a sustainable lifestyle while facing increasing population and decreasing natural resources has become one of humanity’s largest challenges. Locating fossil fuels is becoming more difficult while the demand for them to power our societies is ever increasing. Instead of finding more efficient methods of extracting fossil fuels, developing technologies that create renewable substitutes for fossil fuels is now the strategy. Algae biofuel matches fossil fuel performance while also meeting the criteria for renewable energy. The focus now shifts to finding methods for commercially producing algae biofuel. Therefore, the objective of this thesis is to develop a system that provides …

Linear Power-Efficient Rf Amplifier With Partial Positive Feedback, Matthew E. King

Master's Theses

Over the last decade, the number of mobile wireless devices on the market has increased substantially. New “multi-carrier” modulation schemes, such as OFDM, WCDMA, and WiMAX, have been developed to accommodate the increasing number of wireless subscribers and the demand for faster data rates within the limited commercial frequency spectrum. These complex modulation schemes create signals with high peak-to-average power ratios (PAPR), exhibiting rapid changes in the signal magnitude. To accommodate these high-PAPR signals, RF power amplifiers in mobile devices must operate under backed-off gain conditions, resulting in poor power efficiency. Various efficiency-enhancement solutions have been realized for backed-off devices …