Electrical and Electronics Commons^™

Efficiency Performance Improvement Using Parallel Dc-Dc Converters With A Digital Controller, Daniel Forbes

Master's Theses

A system to improve efficiency performance of a DC-DC converter is simulated and built. The proposed system combines multiple DC-DC converters in parallel and implements a digital control scheme and load-share controller. A model of the system is developed in MATLAB Simulink and the model demonstrates the improved converter’s efficiency particularly at low load conditions. This simulation is then designed into a hardware system running three DC-DC converters in parallel, controlled by a microcontroller and a load-share controller. The hardware also confirms the simulation results, although some hardware refinements are evident as simulation results are superior. The system is designed …

Polar Field Oriented Control With 3rd Harmonic Injection, Martin Todd Hess

Master's Theses

Abstract

POLAR FIELD-ORIENTED CONTROL

with

3^RD HARMONIC INJECTION

Martin Todd Hess

Field Oriented Control (FOC), also known as vector control, is a widely used and well documented method for controlling Permanent-Magnet Synchronous Motors (PMSM) and induction motors. Almost invariably the orientation of the stator and rotor (field) fluxes are described in rectangular coordinates. In this thesis we explore the practicality of using polar coordinates.

Third harmonic injection is also a well-known technique that allows full utilization of the bus (DC-link), thus allowing the motor to run to full base speed without the use of field weakening. This technique potentially …

Impacts Of Plug-In Electric Vehicle On Residential Electric Distribution System Using Stochastic And Sensitivity Approach, Henry Chigozie Ureh

Master's Theses

Plug-in Electric Vehicles (PEVs) are projected to become a viable means of transportation due to advances in technology and advocates for green and eco-friendly energy solutions. These vehicles are powered partially, or in some cases, solely by the energy stored in their battery packs. The large sizes of these battery packs require large amount of energy to charge, and as the demand for PEV increases, the increase in energy demand needed to recharge these PEV batteries could pose problems to the present electric distribution system. This study examines the potential impacts of PEV on a residential electric distribution system at …

Development And Prototyping Of A Ground Fault Circuit Interrupter For 3-Phase 480 Volt Systems, Matthew R. Norlander

Master's Theses

Ground Fault Circuit Interrupter (GFCI) technology was first introduced in the NEC in 1971, yet four decades later the technology has not been introduced to a great extent outside of the home environment. This thesis introduces the difficulties encountered in low-voltage three phase ground fault current detection, and adopts a previously patented tripping scheme to develop and prototype a digital relay for 3-phase 480 volt systems capable of the sensitivity and speed required for personnel safety. Results demonstrate the feasibility of the concept and suggest commercial development should be pursued. The prototype is capable of mA sensitivity and reliably detects …

Experimental And Numerical Investigations Of Tubular-Shaped Direct Methanol Fuel Cells (Dmfcs), Travis R. Ward

Master's Theses

This study focuses on both the numerical and experimental investigations of the novel, passively operated, tubular-shaped, Direct Methanol Fuel Cell (DMFC) as an alternative geometry to the traditional planar-shaped fuel cell. The benefit of the tubular geometry compared to the planar geometry is the higher instantaneous volumetric power density provided by the larger active area, which could be beneficial in applications that require a high instantaneous power while occupying a small volume. First, a two-dimensional, two-phase, non-isothermal model was developed to investigate the steady-state performance and design characteristics of a tubular-shaped, passive DMFC. It was found that a higher ambient …

Off-Grid Public Lighting System – Design And Characterization Of An Led Luminaire, Quanghuy Le

Master's Theses

The technological advances made in the photovoltaic industry have led to a vast exploration of self-sustaining systems.  As the consumer demand for electricity rises from increasing population and development of existing technologies, new practices in system designs are required to relieve the impact on the electrical grid.

This thesis delves into a developing concept of using photovoltaic modules for roadway lighting, with emphasis on establishing the fundamental design for a “spot-lighting” luminaire.  By effectively extinguishing various sections of the luminaire in the absence of pedestrian trafficking, the proposed design and implementation will minimize the prolonged costs, as well as the …

Modeling And Analysis Of The Effects Of Pcb Parasitics On Integrated Dc-Dc Converters, Darwin Domingo Fernandez

Master's Theses

Load transients are prevalent in every electronic device including semiconductor memory, card readers, microprocessors, disc drives, piezoelectric devices, and digitally based systems. They are capable of producing voltage stress, introducing noise, and degrading device functionality. In order to avoid damage to the device, a feedback control loop is implemented with system compensation to regulate the output voltage deviations by the converter. Because designing compensation networks can be rather complicated, DC-DC converters with integrated feedback control topologies help minimize design time and complexity of converter compensation at the expense of design flexibility. This thesis widens the limitations of an integrated DC-DC …

Development Of A Cubesat Instrument For Microgravity Particle Damper Performance Analysis, John Trevor Abel

Master's Theses

Spacecraft pointing accuracy and structural longevity requirements often necessitate auxiliary vibration dissipation mechanisms.  However, temperature sensitivity and material degradation limit the effectiveness of traditional damping techniques in space.  Robust particle damping technology offers a potential solution, driving the need for microgravity characterization.   A 1U cubesat satellite presents a low cost, low risk platform for the acquisition of data needed for this evaluation, but severely restricts available mass, volume, power and bandwidth resources.  This paper details the development of an instrument subject to these constraints that is capable of capturing high resolution frequency response measurements of highly nonlinear particle damper dynamics.

Bridgeless Active Power Factor Correction Using A Current Fed Push Pull Converter, Jeramie Seth Bianchi

Master's Theses

ABSTRACT

Bridgeless Active Power Factor Correction

Using a Current Fed Push Pull Converter

Jeramie Seth Bianchi

Switched Mode Power Supplies have become increasingly popular for efficient methods of delivering power to an assortment of electronic devices. This thesis proposes a method of using a current fed push pull converter to provide active power factor correction and rectification in a single stage. While most AC-DC converters utilize a bridge rectifier to convert AC-DC and then perform DC-DC conversion, the proposed circuit will utilize its output diodes to perform rectification, thus eliminating the need for a bridge rectifier. This circuit will also …

A Frequency-Modulated Continuous Wave-Based Boundary Detection System For Determination Of Monitoring Region For An Indoor Ultra-Wideband Short Range Radar-Based Eldercare Monitoring System, Wilson Tang

Master's Theses

Falls are a cause of concern for the elderly since it can render a person immobile. A monitoring system can summon immediate aid by the automatic detection of fall events. The application of ultra-wideband (UWB) signals for a monitoring system was chosen due to its unique characteristics such as wide spectrum, immunity to interference, penetrability, and application for the detection of people. Part of this monitoring system is boundary detection with the purpose of isolating the location of fall events and to function as a mask to define an area of interest. A study of various localizing methods using measurements …

Photovoltaic Emulator Adaptable To Irradiance, Temperature And Panel Specific I-V Curves, Joseph Gamos Durago

Master's Theses

This thesis analyzes the design and performance of a photovoltaic (PV) emulator. With increasing interest in renewable energies, large amounts of money and effort are being put into research and development for photovoltaic systems. The larger interest in PV systems has increased demand for appropriate equipment with which to test PV systems.

A photovoltaic emulator is a power supply with similar current and voltage characteristics as a PV panel. This work uses an existing power supply which is manipulated via Labview to emulate a photovoltaic panel. The emulator calculates a current-voltage (I-V) curve based on the user specified parameters of …

Energy Harvesting From Elliptical Machines Using Four-Switch Buck-Boost Topology, Alvin Jay Hilario

Master's Theses

This thesis presents the topic of using the Four-Switch Buck-Boost topology as a DC-DC converter for the Energy Harvesting from Elliptical Machines Project. The project works toward providing a modular synchronous power generation system. Due to the dynamic and sporadic output voltage and power characteristics of the Precor elliptical machine, the system requires a DC-DC converter as a voltage preregulator. The inherent wide input range, high efficiency, and low parts cost of this converter well suit the application. This paper further discusses other topologies and their shortcomings, as well as characterizes the Precor elliptical machine and Enphase Microinverter for interfacing. …

Design And Analysis Of A Wind Energy Harvesting Circuit Using Piezoelectric Polymers, Jameson J. Thornton

Master's Theses

This thesis investigates a relatively new method for harvesting wind energy by using flexible piezoelectric polymers with additional sails to increase their ability to harvest wind energy. This paper also introduces a new topology deemed the “stacked buck” that allows for multiple inputs to a system with a single output. Derivations and analysis detail the workings of the “stacked buck” with a laboratory test to show a working model. This paper also reports another experiment done in a wind tunnel to analyze the capability of the piezoelectric polymers as sources to the “stacked buck” topology with measurements of the power …

Universal Engineering Programmer – An In-House Development Tool For Developing And Testing Implantable Medical Devices In St. Jude Medical, Khoa Tat Do

Master's Theses

During development and testing of the functionality of the pacemaker and defibrillator device, engineers in the St. Jude Medical Cardiac Rhythm Management Division use an in-house development tool called Universal Engineering Programmer (UEP) to ensure the device functions as expected, before it can be used to test on an animal or a human during the implantation process.  In addition, some applications of UEP are incorporated into the official releases of the device product.  UEP has been developed and used by engineers across departments in the St. Jude Medical Cardiac Rhythm Management Division (CRMD).  This thesis covers the flexible and reusable …

Class-F Power Amplifier With Maximized Pae, Kai Shing Tsang

Master's Theses

Due to the rapid development of telecommunication devices, operating speeds are getting faster and more power is being consumed by those devices. Therefore, there is a big concern on how to prolong the battery life in order to fit consumers’ needs. Power amplifiers (PA) at the front end of wireless equipment have drawn a big concern from engineers because of their large power consumption in the system. There is a lot research conducted on PA solutions for improving power-added efficiency (PAE) of amplifiers. PAE is a figure of merit representing how efficient the PA converts DC power to RF power. …

Enhanced Cal Poly Super System Simulink Model, Matthew Ogden Mcfarland

Master's Theses

The Cal Poly Sustainable Power for Electrical Resources (SuPER) project is a solar power DC distribution system designed to autonomously manage and supply the energy needs of a single family off-the-grid home. The following thesis describes the improvement and re-design of a MATLAB Simulink model for the Cal Poly SuPER system. This model includes a photovoltaic (PV) array, a lead-acid gel battery with temperature effects, a wind turbine model, a re-designed DC-DC converter, a DC microgrid, and multiple loads. This thesis will also include several control algorithms such as a temperature controlled thermoelectric (T.E.) cooler, intelligent load switching, and an …

Asynchronous Mips Processors: Educational Simulations, Robert L. Webb

Master's Theses

The system clock has been omnipresent in most mainstream chip designs. While simplifying many design problems the clock has caused the problems of clock skew, high power consumption, electromagnetic interference, and worst-case performance. In recent years, as the timing constraints of synchronous designs have been squeezed ever tighter, the efficiencies of asynchronous designs have become more attractive. By removing the clock, these issues can be mitigated. How- ever, asynchronous designs are generally more complex and difficult to debug. In this paper I discuss the advantages of asynchronous processors and the specifics of some asynchronous designs, outline the roadblocks to asynchronous …

Systems Engineering Analysis And Digital Communication Bus Design For The Cal Poly Super Project, Matt Marcus Camack

Master's Theses

With an expected lifetime of 20 years and an expected cost of $500, the Cal Poly Sustainable Power for Electrical Resources (SuPER) project needed a strong central design. This thesis looks at the work completed by students over the previous 5 years, with an eye on the future, to create the phase 2 design. Part of this new structure focuses on a distributed communication bus for monitoring system health and status. Instead of complex and costly computer or FPGA systems, the new system will run solely with microcontrollers. This reduces costs and will hopefully still be used within 5, 10, …

Negative Conductance Load Modulation Rf Power Amplifier, Cody R. Neslen

Master's Theses

The number of mobile wireless devices on the market has increased substantially over the last decade. The frequency spectrum has become crowded due to the number of devices demanding radio traffic and new modulation schemes have been developed to accommodate the number of users. These new modulation schemes have caused very poor efficiencies in power amplifiers for wireless transmission systems due to high peak-to-average power ratios (PAPR). This thesis first presents the issue with classical power amplifiers in modern modulation systems. A brief overview of current attempts to mitigate this issue is provided. A new RF power amplifier topology is …

Pulse Density Modulated Soft Switching Cycloconverter, Jesse Timothy Adamson

Master's Theses

Single stage cycloconverters generally incorporate hard switching at turn on and soft switching at turn off. This hard switching at turn on combined with the slow switching speeds of thyristors (the switch of choice for standard cycloconverters) limits their use to lower frequency applications.

This thesis explores the analysis and design of a pulse density modulated (PDM), soft switching cycloconverter. Unlike standard cycloconverters, the controller in this converter does not adjust thyristor firing angles. It lets only complete half cycles of the input waveform through to the output. This allows and requires a much greater frequency step down from the …

Modular Laser Combat System For Remotely Operated Vehicles: Bridging The Gap Between Computer Simulation And Live Fire, Thomas Edward Fulenwider

Master's Theses

In the emerging industry of small unmanned vehicles, pioneered by small businesses and research institutions, a suitable combat system test platform is needed. Computer simulations are useful, but do not provide the definitive proof of effective operation necessary for deployment of a combat system. What is needed is an affordable simulated weapons system that enables live flight testing without the used of live weaponry.

A framework is developed here for the construction of a simulated weapon using Free Space Optical (FSO) infrared communication. It is developed in such a way to ensure compatibility with a variety of platforms including ground …

A Constant Conduction Angle Biased Rf Power Amplifier For Improved Linearization In Class C Operation, Greg Lacaille

Master's Theses

Class C power amplifiers offer higher efficiency than class B power amplifiers, but suffer from poor linearity. A feedback based biasing system to improve the linearity of a class C power amplifier is designed. A class B amplifier with a gain of 20 dB and 20 MHz bandwidth at 900 MHz acts as the launching point for the design. The biasing and output network of the class B power amplifier is modified to produce a class C amplifier at conduction angles of 180°, 162°, 126°, 90°, and 54°. A feedback based biasing system, which uses two matched and scaled down …

The Design And Manufacture Of A Light Emitting Diode Package For General Lighting, Michael S. Krist

Master's Theses

Lighting technologies have evolved over the years to become higher quality, more efficient sources of light. LEDs are poised to become the market standard for general lighting because they are the most power efficient form of lighting and do not contain hazardous materials. Unfortunately, LEDs pose unique problems because advanced thermal management is required to remove the high heat fluxes generated by such relatively small devices. These problems have already been overcome with complex packaging and exotic materials, but high costs are preventing this technology from displacing current lighting technologies.

The purpose of this study is to develop a low-cost …

Swept-Frequency Sampled Grating Distributed Bragg Reflector Lasers Optimized For Optical Coherence Tomography Applications, Brandon J. George

Master's Theses

Swept Frequency Source Optical Coherence Tomography (OCT) requires high repetition rate and wide spectral width wavelength tunable sources at a low cost. The sampled grating distributed Bragg reflector (SG-DBR) laser provides wide wavelength tuning range while exhibiting a wavelength switching speed that is among the fastest currently available. The SG-DBR laser is used to generate linear frequency ramps with high repetition rates. Since the SG-DBR laser is currently used for the telecommunications industry in high volume, the price of the system is much lower than current OCT sources. Therefore the SG-DBR laser provides a practical solution for Swept Source OCT. …

Design And Development Of Rapid Battery Exchange Systems For Electric Vehicles To Be Used As Efficient Student Transportation, Jonathan A. Bevier

Master's Theses

Rapid battery exchange systems were built for an electric van and pedal assist electric bike as a method of eliminating the need to recharge the vehicles batteries in order to increase the feasibility of using electric propulsion as a method of efficient student transportation. After selecting proper materials it was found that the systems would need a protective coating to ensure consistent operation. 1020 cold rolled steel samples coated with multiple thicknesses of vinyl resin paint, epoxy resin paint, and powder coating were subjected to environmental wear tests in order to determine if the type and thickness of common protective …

Analysis & Design Of Improved Multiphase Interleaving Dc-Dc Converter With Input-Output Bypass Capacitor, Rudi Rudianto

Master's Theses

As the transistor count per chip in computer microprocessors surpasses one billion, the semiconductor industry has become more and more concerned with meeting processor’s power requirements. This poses a design challenge for the power supply module, especially when the processor operates at low voltage range. For example, the electrical requirement for the newest Intel microprocessors has exceeded 100A with an input voltage of approximately 1V. To overcome this problem, multiphase DC-to-DC converters encased in a voltage regulator module (VRM) have become the standard means of supplying power to computer microprocessor.

This study proposes a new topology for the multiphase DC-to-DC …

Analysis And Design Of Continuous Input Current Multiphase Interleaved Buck Converter, Sean Michael Zich

Master's Theses

The power requirements for microprocessors have been increasing per Moore's Law. According to International Technology Roadmap (ITRS), Voltage Regulator Module (VRM) for microprocessors will be about 200 W at 1 V output in 2010. With the VRM’s topology of synchronous buck, serious technical challenges such as small duty cycle, high switching frequencies, and higher current demands, contribute to decreased power density and increased cost.

This thesis proposes a Continuous Input Current Multiphase Interleaved Buck topology to solve the technical challenges of powering future microprocessors. This new topology is aimed to improve past topologies by providing continuous input current and improved …

Analysis And Design Of Interleaving Multiphase Dc-To-Dc Converter With Input Lc Filter, Kevin Thomas Delrosso

Master's Theses

The future of microprocessors is unknown. Over the past 40 years, their historical trend has been for adopting smaller and more powerful designs that drive the world that we live in today. The state of the microprocessor business today faces a crossroad, wishing to continue on the historical trend of doubling the number of transistors on a chip every 18 months (Moore’s Law) but also facing the realistic task of needing to power these sophisticated devices. With the low voltages and high currents that are required for these microprocessors to operate, it poses a difficult task for the future designers …