Civil Engineering Commons^™

Impact-Resistant Behavior Of Reinforced Concrete Bridge Columns, Chen Fang

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The damage caused by a vehicle collision on a pier column can be catastrophic for the functionality of a bridge, even a total collapse of the bridge. ❖ A vehicle collision and a subsequent vehicle blast cause more damages on the bridge. ❖ Limited researches have been conducted to investigate the behavior of the bridge subjected to the combined effect of vehicle collision and blast. ❖ It is necessary to analyze the responses of the bridge under the vehicle collision and blast and provide some design suggestions to strengthen the bridge.

Conclusions ❖ The finite element models including column, pile …

Optimizing Steel Railway Truss Bridge Health Monitoring, Ahmed Rageh, Daniel Linzell

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Problems - Steel Railway Trusses • Aging • Large system – bridge AND railway • Labor intensive condition eval • Reported conditions: Stringer-to-floor beam connections [Haghani 2012] Stringer flange clip angle cracks [Haghani 2012] Unequal eyebars stress distribution [DelGrego 2008] Displaced eyebar pins [DelGrego 2008

Problems – Condition Evaluation • Visual inspection: Prescribed frequency Costly Subjected to human interpretation • Sensors: Focused on a single bridge Extensive array Costly

Influence Of Skew And Nonlinear Deck On Elastic Versus Inelastic Distribution Behavior And Ultimate Capacity Of Steel Girder Bridges, Fayaz Sofi, Joshua Steelman

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Research Objectives

• Assessment of alternative load distribution methodologies for potential discrepancies that arise when evaluating distribution behavior of skewed steel girder bridges.

• Investigate the influence of skew and material nonlinearities (concrete cracking and steel yielding) on

• Load distribution behavior (elastic versus inelastic).

• System capacities (yielding and ultimate).

Summary and Conclusions • Influence of skew was examined on load distribution behavior, and nonlinear system-based capacities (yielding and ultimate) of composite steel girder bridges in presence of full material nonlinearities. In addition, assessment of two general definitions (beam-line and response fraction approaches) for quantifying load distribution behavior was …

Practical Considerations In Determining Timber Pile Depth Using The Sonic Echo Method, Ali F. Jwary

Civil Engineering ETDs

The Federal Highway Administration indicates that about 85,000 bridges in the United States have no original contract documents with information about the type, depth, geometry and material of their foundations (FHWA, 2010). Furthermore, the National Bridge Inventory (NBI) provides information about 86,133 bridges nationwide that are rated as scour critical because of unknown foundation condition. In New Mexico, there are more than 281 bridges with unknown foundations, which are owned by the New Mexico Department of Transportation; 71 of these are timber bridges. These data indicate a serious problem that needs decisive action to assess the unknown bridge foundation characteristics …

Bicp Global Bim Study - Lessons For Ireland’S Bim Programme, Barry Mcauley, Alan Hore, Roger West

Reports

The Construction IT Alliance (CitA) has been promoting the benefits of digitisation in the construction and engineering industry in Ireland since its formation back in 2002. Whilst the Alliance has always strived to ensure that its members are exposed to a wide spectrum of contemporary digital tools and processes, the concept of Building Information Modelling (BIM) has dominated the focus of its activities over the past five years.

BIM can be described as a digital tool that facilitates everybody to better understand a building or structure through the use of a digital model which draws on a range of data …

Bond Between Microwave Cured Repair And Concrete Substrate, Konstantinos Grigoriadis, P. S. Mangat, Shahriar Abubakri

Henry M. Rowan College of Engineering Departmental Research

The bond strength between a concrete substrate and repair patch is critical to its durability. This paper investigates the effect of microwave curing the freshly applied repair, for 45 min at 132 Watts, on the 28 day bond strength between substrate concrete and different commercial repair materials. The repairs were applied at different ambient temperatures of 20, 10, 2 and −5 °C. Tensile split tests on repaired cube specimens were performed to determine the interfacial bond strength. The ability of microwave curing to prevent the detrimental effects of freezing at early age on the bond and compressive strength of repair …

Restrained Shrinkage Of Fly Ash Based Geopolymer Concrete And Analysis Of Long Term Shrinkage Prediction Models, Md R. Islam, Mahbub K. Ahmed, Hosney Ara Begum, Erez N. Allouche

Journal of the Arkansas Academy of Science

The research presented in this manuscript describes the procedure to quantify the restrained shrinkage of geopolymer concrete (GPC) using ring specimen. Massive concrete structures are susceptible to shrinkage and thermal cracking. This cracking can increase the concrete permeability and decrease the strength and design life. This test is comprised of evaluating geopolymer concrete of six different mix designs including different activator solution to fly ash ratio and subjected to both restrained and free shrinkage. Test results obtained from this experimental setup was plotted along with the available empirical equation to observe the shrinkage strain of GPC and a model was …

Uav-Based Bridge Inspection And Computational Simulations, Luis Duque

Electronic Theses and Dissertations

The use of Unmanned Aerial Vehicles (UAV), commonly known as drones, has significantly increased in the field of civil engineering due to the poor condition of the United States’ infrastructure. The American Society of Civil Engineers (ASCE) recently reported that more than 9.1% of the United States’ bridges were structurally deficient and required attention and maintenance to ensure appropriate structural performance. Meanwhile, current practices are expensive and unsafe for bridge inspectors, requiring innovative and safer methods for the study of bridges. The goal of this paper was to identify better techniques to not only inspect, quantify, and determine the effect …

Compact Facility For Testing Steady And Transient Thermal Performance Of Building Walls, Aimee Byrne, Gerard Byrne, Anthony Robinson

Articles

Energy efficiency retrofit of buildings represents a key effort in reducing EU energy demand by 20% by 2020. However, predictions tend to overestimate savings by large percentages. The shortfall in savings can be attributed to incorrect predictive techniques, comfort takeback along with other behavioural and workmanship variables. Common predictive techniques related to heat loss tend to be based on the U-value of the building envelope. This paper presents the design of a more straightforward and compact version of the traditional Hot-Box apparatus (measures U-value) which instead determines the thermal resistance of samples of building envelope. U-value includes the need to …

Optimising The Performance Of Cement-Based Batteries, Aimee Byrne, Shane Barry, Niall Holmes Dr., Brian Norton

Articles

The development of a battery using different cement-based electrolytes to provide a low but potentially sustainable source of electricity is described. The current, voltage, and lifespan of batteries produced using different electrolyte additives, copper plate cathodes, and (usually) aluminium plate anodes were compared to identify the optimum design, components, and proportions to increase power output and longevity. Parameters examined include water/cement ratio, anode to cathode surface area ratio, electrode material, electrode spacing, and the effect of sand, aggregate, salts, carbon black, silica fume, and sodium silicate on the electrolyte. The results indicate that the greatest and longest lasting power can …

Load Estimation, Structural Identification And Human Comfort Assessment Of Flexible Structures, Ozan Celik

Electronic Theses and Dissertations

Stadiums, pedestrian bridges, dance floors, and concert halls are distinct from other civil engineering structures due to several challenges in their design and dynamic behavior. These challenges originate from the flexible inherent nature of these structures coupled with human interactions in the form of loading. The investigations in past literature on this topic clearly state that the design of flexible structures can be improved with better load modeling strategies acquired with reliable load quantification, a deeper understanding of structural response, generation of simple and efficient human-structure interaction models and new measurement and assessment criteria for acceptable vibration levels. In contribution …

Site Specific Sinkhole Risk Assessment In Central Florida Using Cone Penetrometer Testing, Ryan Shamet

Electronic Theses and Dissertations

As Florida's population is expanding and greater fluctuations in groundwater levels are being recorded, Central Florida has been experiencing a higher frequency of sinkhole occurrences than ever before in recorded history. Sinkholes in Central Florida are formed by a combination of bedrock weathering and overburden soil erosion due to the groundwater recharge and are a part of Florida's past and future geology. The initial stage of a sinkhole is referred to as soil raveling and is the most effective time to perform soil improvement measures, such as grouting, to mitigate further expansion of a subterranean void. Subsurface exploration tests, commonly …

Air Injection As A Scour Countermeasure At Bridge Piers, Ravi Teja Reddy Tippireddy

Dissertations, Master's Theses and Master's Reports

Local scour is a major cause of concern for the stability of bridge piers and the safety of the public using the bridges. Structural countermeasures and flow-altering devices have been developed to deal with local scour. Many armoring structural countermeasures are very effective and efficient in clear water conditions but are susceptible to moving bed forms and leaching. The flow-altering devices are effective in both clear water conditions and moving bed forms, but are prone to clogging, less efficient in changing flow direction, etc. This study aims to reduce the local scour by injecting air in order to reduce the …

Total Bridge Replacement Of M-13 Over Cheboyganing Creek, Daniel Burns

Honors Theses

The Michigan Department of Transportation sought a proposal consisting of design and construction engineering services for the total bridge replacement of M-13 over Cheboyganing Creek. The M-13 Bridge Project is located on M-13 over Cheboyganing Creek on the Saginaw River in Portsmouth Township, Bay County, Michigan.

Several components of the existing bridge have been rated in poor or serious condition on the National Bridge Inventory rating scale. A total bridge replacement is required and aligns with MDOT strategies to address critical infrastructure needs in the state as well as the Bay Region's five-year plan for managing bridge and culvert infrastructure. …

Expression And The Functional Study Of Fusion Proteins Α-Amylase And Hemolysin- Αas An Application In Biofilm Polysaccharide Degradation, Gede Yuda Sugiarta, Anggoro Wiseso, Siska Yuliana Sari, Etri Dian Kamila, Vanessa Geraldine, Diana Christina, Muhammad Hanifi, Dwiantari Satyapertiwi, Robby Hertanto, Budiman Bela, Masafumi Yohda, Muhamad Sahlan

Makara Journal of Technology

Biofilm is an aggregate of consortium bacteria that adhere to each other on a surface. It is usually protected by the exopolysaccharide layer. Various invasive medical procedures, such as catheterization, endotracheal tube installation, and contact lens utilization, are vulnerable to biofilm infection. The National Institute of Health (NIH) estimates 65% of all microbial infections are caused by biofilm. Periplasmic α-amylase (MalS) is an enzyme that hydrolyzes α-1, 4- glicosidic bond in glycogen, starch, and others related polysaccharides in periplasmic space. Another protein called hemolysin-α (HlyA) is a secretion signal protein on C terminal of particular peptide in gram negative bacteria. …

Design Of The Human Assembly Strategy In A Self-Optimizing Assembly Cell: A Case Study Of Indonesians, Novie Susanto, Ratna Purwaningsih, Kharisma Panca Kurniawati

Makara Journal of Technology

This paper presents a continuing study of the human cognitive aspect application in the technical systems. The last studies design a human-centered design based on the German culture. The result shows a significant difference of human performance between Germans and Indonesians. Therefore, this study examines the human cognitive model based on Indonesian culture to investigate whether the different cognitive model based on the culture aspect can improve the human performance. The study was conducted on 60 people classified by age, young (16-34 years old) and old (older than 34 years old). Participants render predictions on an assembly activity for two …

Optimizing Supply Chain Collaboration Based On Agreement Buyer-Supplier Relationship With Network Design Problem, Wahyudi Sutopo, Ayu Erliza, Arien Heryansyah

Makara Journal of Technology

In recent years, the rising competitive environment with shorter product life cycles and high customization forces industries to increase their flexibility, speed up their response, and enhance concurrent engineering designs. To integrate these prospects, supply chain collaboration becomes a pertinent strategy for industries to strengthen their competitiveness. The network design problem is used to implement supply chain collaboration. In the buying and selling process, sharing information between buyer and supplier are important to obtain a transaction decision. The optimimum supply chain profit can be identified by mathematical model of network design problem. The Mathematical Model takes into consideration the uncertainity …

Effect Of Milling On The Densification Of Sic-Basedcomposites From Polysilazane, Alfian Noviyanto, Toshiyuki Nishimura

Makara Journal of Technology

High density SiC-based composites from polysilazane were fabricated by high energy milling and hot pressing. After cross-linking at 200 °C, the polysilazane was pyrolysed at 1000 °C in N2 for 2 h to form amorphous Si-C-N-O followed by high energy milling for 1 h. Milled amorphous Si-C-N-O was sintered in hot pressing at 1600 and 1700 °C for 1 h in vacuum under the applied pressure of 50 MPa. Although no sintering additives were used, dense SiC-based composites were obtained with this method. Sintered density was 3.04 g/cm3, while only 2.57 g/cm3 for amorphous Si-C-N-O without milling. It is suggested …

Characterization And Utilization Of Calcium Oxide (Cao) Thermally Decomposed From Fish Bones As A Catalyst In The Production Of Biodiesel From Waste Cooking Oil, Aldes Lesbani, Sabat Okta Ceria Sitompul, Risfidian Mohadi, Nurlisa Hidayati

Makara Journal of Technology

Thermal decomposition of fish bones to obtain calcium oxide (CaO) was conducted at various temperatures of 400, 500, 800, 900, 1000, and 1100 °C. The calcium oxide was then characterized using X-ray diffractometer, FTIR spectrophotometer, and SEM analysis. The calcium oxide obtained from the decomposition at 1000 °C was then used as a catalyst in the production of biodiesel from waste cooking oil. Diffraction pattern of the calcium oxide produced from decomposition at 1000 °C showed a pattern similar to that of the calcium oxide produced by the Joint Committee on Powder Diffraction Standard (JCDPS). The diffractions of 2q values …

Thermoeconomic Optimization Of Cascade Refrigeration System Using Mixed Carbon Dioxide And Hydrocarbons At Low Temperature Circuit, Nasruddin Nasruddin, Arnas Arnas, Ahmad Faqih, Niccolo Giannetti

Makara Journal of Technology

Many applications and industrial processes require very low cooling temperature, such as cold storage in the biomedical field, requiring temperature below -80 °C. However, single-cycle refrigeration systems can only achieve the effective cooling temperature of -40 °C and, also, the performance of the cycle will decrease drastically for cooling temperatures lower than -35°C. Currently, most of cascade refrigeration systems use refrigerants that have ozone depletion potential (ODP) and global warming potential (GWP), therefore, in this study, a cascade system is simulated using a mixture of environmentally friendly refrigerants, namely, carbon dioxide and a hydrocarbon (propane, ethane or ethylene) as the …

Developing Road Infrastructure Route Planning: Increasing Feasibility Of Toll Road Project, Mohammed Ali Berawi, Teuku Yuri Zagloel, Perdana Miraj, Abdur Rohim Boy Berawi, Wellsi Titaheluw, Saipol Bari Bin Abd Karim

Makara Journal of Technology

Indonesian government attempts to improve connectivity and to increase regional activities in Sumatera Island through the development of Trans Sumatera Toll Road (TSTR). However, despite its benefits to local economic development in Sumatera, the project shows low feasibility due to a low amount of investment. It can be attributed from the lack of planning in the initial phase to produce a comprehensive route that considers the various potentials of the regions. Thus, this research aims to investigate alternative route planning of Trans Sumatera Toll Road particularly in this paper for Central Sumatera by studying Gross Regional Domestic Product (GRDP), population …

Thermal And -Γ –Ray Irradiation Effects On The Ionic Conductivity Of (Licl)X(Montmorillonite)1-X, Safei Purnama, Aziz Khan Jahja, Takeshi Sakuma

Makara Journal of Technology

Compositesof montmorillonite (MMT) - lithium salts have been prepared using a simple process of powders mixing followed by heating. The powders resulting from this method are expected to beionic conductors with a high ionic conductivity characteristics. This characteristics is also further improved by employing gamma-ray irradiation technique at specified irradiation doses. The best results were obtained for the (LiCl)0.5(MMT)0.5 composite with a room temperature ionic conductivity of 2.192 mS/cm, which then increases to ~5 mS/cm after gamma irradiation at a dose of 400 kGy. This value is equivalent to the value of the ionic conductivity of current commercial rechargeable lithium …

Cement Asphalt Mortar Modelling And Its Influence On High-Speed Train–Bridge System In Presence Of Moderate Earthquakes And Service Loading, Lingkun Chen

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Numerical Modeling And Seismic Assessment Of Smart Isolation System For High-Speed Railway Rc Bridge Subjected To Near-Field Ground Motions, Lingkun Chen

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Buckling Analysis Of Laminated Composite Box Beams, Domagoj Lanc, Goran Turkalj, Josip Brnic

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Restoring Capacity In Compromised Glued Laminated Beams, Cole Moller

Graduate Theses & Non-Theses

After structural fires are extinguished, presuming the structure is not a total loss, structural wood members can be inspected for residual properties. Through this research, we explored alternative methods aimed at keeping structurally compromised wood member’s in service when they would otherwise warrant replacement. For this study, we used 24F-V8 DF/DF glued laminated beams that had been loaded to their max capacity; both non-fire damaged and fire damaged. In situations where physical and mechanical changes occur, and the beam warrants individual replacement, a new restoration procedure could be used to salvage the member. Salvaging the member could mean to keep …

Efficient Domain Decomposition Algorithms And Applications In Transportation And Structural Engineering, Paul W. Johnson Iii

Civil & Environmental Engineering Theses & Dissertations

Domain decomposition is a divide-and-conquer strategy. In the first part of this dissertation, a new/simple/efficient domain decomposition partitioning algorithm is proposed to break a large domain into smaller sub-domains, in such a way as to minimize the number of system boundary nodes and to balance the work load for each sub-domain. This new domain decomposition algorithm is based on the network’s shortest path solution. Numerical results indicate that the new Shortest Distance Decomposition Algorithm outperformed the most widely used METIS algorithm in 21 out of 27 tested (transportation) examples. In the second part of this dissertation, another new/simple and highly …

Strength Of Reinforced Concrete Beams With High-Strength Steel, Brian C. Rogers, Aishwarya Puranam, Santiago Pujol

The Summer Undergraduate Research Fellowship (SURF) Symposium

Structures are commonly made of reinforced concrete, which is a composite material made of concrete and steel reinforcement. Using high-strength steel, with yield stress larger than 100 ksi, could help reduce the quantity of steel required in structural members, thus reducing costs and improving constructability. The hypothesis being tested is that smaller quantities of high-strength steel reinforcement (HSSR) can be used in place of conventional steel in reinforced concrete beams while maintaining similar strength and deformation at failure. Two reinforced concrete beams with two different types of longitudinal steel reinforcement were constructed. The beams were 18 in. wide, 30 in. …

High Strength Steel In The Reinforced Concrete Structures: Serviceability, Alan Kanybek, Aishwarya Puranam, Santiago Pujol

The Summer Undergraduate Research Fellowship (SURF) Symposium

The use of high-strength steel (yield stress larger than 100 ksi) in reinforced concrete structures can provide an effective alternative to using conventional steel (yield stress up to 80 ksi). The goal of this study is to investigate if slabs with reduced quantities of high-strength steel reinforcement meet the serviceability criteria. Instantaneous and long-term deflections in slab specimens with conventional steel and reduced amounts of high-strength steel (as compared with conventional steel) were studied. Two sets of two reinforced concrete slabs, each 14 ft. long, 30 in. wide, were built. The depth, quantity, and type of longitudinal reinforcement were varied …

Study On Oil Palm Fresh Fruit Bunch Bruise In Harvesting And Transportation To Quality, Andreas Wahyu Krisdiarto, Lilik Sutiarso

Makara Journal of Technology

There are losses of production due to oil palm field’s material handling. Activities that may raise the losses are harvesting and transportation, which may cause bruise and damage to fruit. This research was aimed to learn the bruise of fresh fruit bunch (FFB) phenomenon in harvesting and transportation. Method used in this research was measuring the bruise area resulted by FFB falling when harvested, loading (throwing up) FFB to truck bin, and transporting using truck. These data, coupled with weight of bruised fruit, were calculated to get FFB bruise index. Each FFB bruise index is related to potential free fatty …