Engineering Commons^™

An Experiential Online Training Approach For Underrepresented Engineering And Technology Students, Arefeh Mohammadi, Kevin Grosskopf, John Killingsworth

Durham School of Architectural Engineering and Construction: Faculty Publications

Workforce pipelines are essential to sustain a productive workforce in an increasingly competitive, high-tech environment. Advanced automation, sensors, materials and data analytics will increase the need for highly skilled workers in the manufacturing (and manufactured construction) sector. Attracting and developing the next-generation workforce is not without its challenges; however, students are often deficient in technical skills and generally have negative perceptions about manufacturing and construction. As a result, new education and training models have been developed to provide instruction at all levels of the educational system, with a focus on both traditional students and non-traditional students, including ethnic minorities, women, …

Design, Construction And Testing Of A 3-Component Force Balance For Educational Wind Tunnels In Undergraduate Aerodynamics, Milan Tomin, Marco Scipioni, Benjamin Gatti

Journal of Aviation/Aerospace Education & Research

This article is focused on providing detailed instructions on how to build and use a force balance for educational wind tunnels. The article’s objective is to encourage undergraduate students in underfunded programs to engage in the field of aerodynamics. The discussed force balance represents an affordable device that only requires basic components like Arduino board, a servo motor, and acrylic and aluminum as construction materials. A simple data collection example is included at the end of the article showing that this simple force balance can collect meaningful data about lift, drag, and moment coefficient of a tested airfoil.

Pulsed Power Control System, Logan Curtis

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Using Batman Software To Analyze Metabolic Changes In Type 1 Diabetes-Susceptible Rats, Connor Hall

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Additive Manufacturing In Space, Japheth Hayman

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Three-Dimensional Measurement Of Electron Temperature And Density In A Split Ring Resonator Microplasma, Neil Laya

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Reactions At The Critical Point Of Solution, Jason Mote

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Directed Assembly Of Binary Magnetic Particles, Thomas Thelen

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Tunable Refractive Index Through Spatially Modified Nanoparticle Films For Long-Range Spr Biosensing Applications, Stephen Joshua Binderup

Graduate Research Theses & Dissertations

Despite optics and refraction being among the oldest scientific principles, material limitations have prevented scientists from taking full advantage of the potential this technology holds. Indeed, films with designer optical properties have potential for use in exotic cloaking architectures, advanced waveguides, and precise optical biosensors. This thesis focuses on the fabrication methodology for making thin films with refractive index tuned to a desired value through self-assembly of amorphous nanoparticle films made of organosilicate materials. The inclusion of a slowly evaporating polymer phase along with the organosilicate nanoparticles results in nanopores formed within the film, which effectively reduce the film’s refractive …

Machine Learning Analysis To Characterize Phase Variations In Laser Propagation Through Deep Turbulence, Luis Fernando Rodriguez Sanchez

Open Access Theses & Dissertations

The present Dissertation is focused on the analysis of the atmospheric conditions of a turbulent environmental system and its effects on the diffraction of a laser beam that moves through it. The study is based on the optical communication of two labs placed at the summit of two mountains located in Maui, Hawaii. The emitter system is located at the Mauna Loa mountain and the receiver at the Haleakala. The distance between both mountains is 150 km. The emitter system is at a height of 3.1 km and the receiver at 3.4 km. The maritime environment at the location experiences …

Investigation Of Iron Doped Gallium Oxide (Ga-Fe-O) System: Structure Property Relationship And Performance Evaluation For Optical And Catalytic Applications, Swadipta Roy

Open Access Theses & Dissertations

From September 2012 to May 2015, a phenocam monitored the seaward edge of a protected mangrove forest. Calculated GCC revealed seasonal greening patterns of a mangrove species, Rhizophoa apiculata, and an overall increase in the GCC, suggesting mangrove expansion. In comparing temperature and precipitation effects, it was found that this particular mangrove species had a greening optima at temperatures between 28°C and 28.5°C, and greening and canopy development response lag time of 10 weeks in response to precipitation. Tree saplings were monitored and showed to grow by 50%, mostly during a three month period during the rainy season. The establishment …

Photovoltage Enhancement For Stable Perovskite Solar Cells With A Temperature-Controlled Grain Growth Technique, Luis Eduardo Valerio

Open Access Theses & Dissertations

By performing strong characterizations methods, one can begin to fully understand the chemistry and composition behind a great performing perovskite solar cell. Understanding how the interaction between layers inside a solar cell is driven by the temperature and overall environment is a key element to improve the fabrication process and overall efficiency of such cells. This Thesis will present a study of the hybrid organic-inorganic, mixed-cation, mixed-halide, temperature and thickness-controlled perovskite solar cell. A constant power conversion efficiency (PCE) ranging between 15-17% and an open circuit voltage V¬oc above 1.05 V for a wide-band gap perovskite cell is presented.

Design Of A Linerless Cryogenic Propellant Tank For A Small Payload Launch Vehicle, Itzel Adriana Torres

Open Access Theses & Dissertations

The need of lightweight launch vehicles that will reduce the cost and make flights more frequent into orbit has called for an increase of composite materials in the aerospace industry. Composite material’s low thermal conductivity, high resistance to fatigue, and most importantly, low-weight can greatly reduce the cost of launch operations by decreasing the overall weight of the vehicle. Weight and cost savings are critical because any amount of weight that is saved can be directly applied as an additional amount of payload capability. The tanks on space vehicles are pressurized vessels that store fuel at cryogenic temperatures and have …

Synthesis And Advanced Manufacturing Of Polymer Structures And Their Composites, Bethany Rose Wilburn

Open Access Theses & Dissertations

The following research work performed embodies three unique studies of polymer structures and their composites. In general, polymers are viscoelastic, insulative materials that are used for a wide variety of applications within industrial, aerospace, and biomedical fields. Polymers have been studied and optimized for any particular use by chemically synthesizing unique micro-structures, altering the physical properties through fabrication and post-processing, and utilizing 3D printing to achieve complex geometries. In the past decade, additive manufacturing (AM) has drawn extensive attention across academia, industry, and government agencies. It offers unprecedented advantages such as design freedom, rapid prototyping, and customization. In this work, …

Additive Manufacturing Of Engineered Material Systems For Energy Applications, Luis Angel Chavez

Open Access Theses & Dissertations

Despite increasing efforts to use renewable electricity generation techniques in the last couple of decades, the world is still heavily reliant on traditional power generation techniques. This creates the need to make such systems cheaper and less pollutant through improvements to their efficiency. Increasing the efficiency and reliability of energy conversion systems, specially those based on combustion processes has been of interest for many years. However, material limitations have brought these systems to a stagnant condition.

A novel approach to help increase the efficiency of such systems is to closely monitor their operating conditions and therefore be able to increase …

A Probabilistic Creep Constitutive Model For Creep Deformation, Damage, And Rupture, Md Abir Hossain

Open Access Theses & Dissertations

The structural analysis of Industrial Gas Turbine (IGT), Aeroengine, Gen IV nuclear components under in-service conditions at various stress and temperature are susceptible to time-dependent creep deformation and creep induced failure. Such failure phenomena are exacerbated by the randomness in material properties, oscillating loading conditions, and other sources of uncertainty. The demand for physically based probabilistic creep modeling is highly sought by alloy designers. The objective of this study is to develop and validate a probabilistic creep-damage model incorporating multi-sources of uncertainty to replace the traditional deterministic and empirical decision-based modeling. In this study, the deterministic Sine-hyperbolic (Sinh) creep-damage model …

Evaluation And Modeling Of Electrodialysis For High-Recovery Brackish Water Desalination, Shahrouz Jafarzade Ghadimi

Open Access Theses & Dissertations

This research investigates the feasibility of desalination of brackish water with electrodialysis (ED), using laboratory testing and mathematical modeling. Several experiments were performed to characterize ion-specific transport and to evaluate tradeoffs between salinity removal and specific energy consumption. A 200 cm2 Ameridia ED stack was used to perform desalination experiments with real brackish groundwater from the Kay Bailey Hutchison desalination plant in El Paso, Texas, and the results showed limiting current density of 160 A/m2 for 5 cm/s. A higher conductivity reduction was observed for flow velocity of 5 cm/s compared to 13 cm/s. Ion transport selectivity (based on relative …

Evaluation Of Cyclo Olefin Polymer As Sabot Material For High-Density Projectiles, Estebanne Tarango

Open Access Theses & Dissertations

Assuring the integrity of spacecraft and its occupants are a priority in the field of space exploration. Micrometeoroids and orbital debris are one of the primary threats that affect spacecraft materials due to the high kinetic energies involved with hypervelocity impacts. Improvement of projectile launching capabilities prompts the investigation of adequate materials for the manufacturing of sabots able to carry high-density projectiles without catastrophic failure. Polycarbonate (PC) has been the chosen material by the Hypervelocity Team at White Sands Test Facility for sabots on the 0.50 caliber launcher; however, there is a material constraint when the projectile becomes significantly dense …

Design And Operability Of A Pressurized Oxy-Combustion System, Mehrin Chowdhury

Open Access Theses & Dissertations

Fossil fuel powers more than two-thirds of the world’s electricity, a significant share of which is derived from coal power plants. Despite coal being an abundant and energy-rich fuel, the major halt to its progress is greenhouse gas emissions. Greenhouse gases are detrimental to the environment. The search for clean fossil fuel leads to the oxy-combustion process. Oxy-fuel combustion produces sequestrable carbon dioxide as exhaust. Pressurization makes carbon capture more accessible and more energy-efficient. Pressurized oxy-combustion cycles can achieve theoretically high thermal efficiencies along with a 90% carbon capture rate. Additionally, the high energy density allows smaller turbomachinery and save …

The Study Of Non-Permanent Tattoo Ink Using Nano Silver Compounds And Untact 3d Printing Technology, Jisu Lee

Open Access Theses & Dissertations

Due to a recent epidemic of COVID 19, the possibility of 3D tattoo printing technology using the Internet of Things (IoT) control system developed in a non-face-to-face contact process was identified. A non-surgical tattoo process and hygiene safety differentiated with silver tattoo ink was used to solve the health problems arising from the surgical tattoo process and to identify 3D tattoo printing techniques through a non-personal contact concept. During the tattoo processing, the image selected by the customer is sent to a designated printer via an IoT control system in a separate location. A piston-type extruder (PTE) printing technique was …

Testing The Reliability And Flexibility Of Digitizers Adapting The Rf/If Signals Over Ip Applications Using A Testbed Platform, Jose Carlos Sandoval

Open Access Theses & Dissertations

As physical constraints can be challenging for Radio Frequency (RF) telemetry, a new solution has been exploited to support the demand for RF transmissions. As frequency spectrum gets crowded with more technologies, a solution to a reliable transmission is needed. Digitizers can mitigate many of the physical constraints in order to achieve a successful RF transmission. The method includes the conversion of the RF signals to be sent over IP networks, transmit and de-convert the signal. IP networks will mitigate many disadvantages over a regular signal transmission. The authority in charge to allocate frequency bands is the Federal Communications Commission …

Brian Valdez - Dynamics And Control Of A 3-Dof Manipulator With Deep Learning Feedback, Brian Orlando Valdez

Open Access Theses & Dissertations

With the ever-increasing demands in the space domain and accessibility to low-cost small satellite platforms for educational and scientific projects, efforts are being made in various technology capacities including robotics and artificial intelligence in microgravity. The MIRO Center for Space Exploration and Technology Research (cSETR) prepares the development of their second nanosatellite to launch to space and it is with that opportunity that a 3-DOF robotic arm is in development to be one of the payloads in the nanosatellite. Analyses, hardware implementation, and testing demonstrate a potential positive outcome from including the payload in the nanosatellite and a deep learning …

Overview Of Changes To The S-Stem And Iuse Programs, Stephanie E. August

Computer Science Faculty Works

The National Science Foundation (NSF) Division of Undergraduate Education (DUE) Scholarships in Science, Technology, Engineering, and Mathematics (S-STEM, NSF 20-526) [5] and Improving Undergraduate STEM Education: Education and Human Resources (IUSE: EHR, NSF 19-601) [4] programs are frequent funding targets for the computer science education (CSEd) community. These programs were discussed in the context of evaluation in an earlier column [1]. NSF programs evolve over time to respond to community needs and changes at the Foundation. The purpose of this column is to bring recent changes to S-STEM and IUSE and other changes at NSF that impact CSEd to the …

Levitate, Stephen Hargreaves, Isaac Hammonds, Russel Pease, Joseph Morris

Williams Honors College, Honors Research Projects

Levitate is designed to create a healthier work environment by providing a way of entertaining a worker while not distracting them. To fulfill this task, the device needs to be interesting and self-sufficient while not being overly flashy. To complete this task, Levitate is designed so that it is able to lift a platform from rest using magnetism and that will be able to stabilize itself using electromagnets. It initiates this process by lifting the permanent magnet using servo motors. Then, the device is able to achieve stability through the use of hall sensors feeding their results to the board …

Solar-Powered Exploration Of The Venus Atmosphere, Marc Migliozzi, Cory Everman, Rebecca Buerhle, Umar Muhammed, Steven Abbate, Chase Champagne

Williams Honors College, Honors Research Projects

The objective of this study was to design a solar powered, unmanned aircraft to orbit in the upper Venus atmosphere and search for signs of alien life. Topics of flight conditions, signs of life, basic mission plan, source of power, design process, instrumentation, and final designs are covered. Solar energy is ideal for this type of mission because it is the only reliable and abundant energy source accessible for long term space travel. The target altitude, being 60 to 70 km, has winds of up to 95 m/s. The aircraft will need to remain stable under such conditions. Due to …

Controlled Crystallization Of Pet Filaments In Additive Manufacturing, Ryan Kordahi

Williams Honors College, Honors Research Projects

Polyethylene terephthalate (PET) appears in daily life in many forms, the most common being disposable soft drink bottling. To deal with the ever-growing quantitity of disposed PET (both in landfills and environment), a waste plan revolving around depolymerization should be implemented. Specifically, the potential of PET depolymerization through aminolysis into useful, low molecular weight monomers will be explored with the end goal of producing a 3D printing filament and analyzing economic feasibility.

Optimization Of E-Textiles For Lactic Acid Detection, Andrew Laboy, Mallory David

Williams Honors College, Honors Research Projects

The overall goal of the project is to develop an e-textile that will be able to determine different characteristics of an athlete's health through multiple sensors. The goal of these sensors is to monitor physiological parameters for health and fitness uses in real time. Building from the existing sodium concentration sensor, these new sensors will detect lactate levels within sweat to monitor instantaneous health which allows customization of workout and overall health regimen.

Evaluating Rubber Aging On Tire Durability: Quantitative Evaluation Of Rubber Aging, Brian Auffenberg

Williams Honors College, Honors Research Projects

Rubber is considered one of the most important polymers in the world due to its variety of uses. There are many different conditions that can affect the useful life of rubber. The purpose of this research was to determine how the mechanical loading on the rubber may affect the aging of the rubber. The scope of the project was to focus on the rubber used for tire production. The research was limited to focusing only on rubber supplied by industry mentors which was styrene-butadiene rubber. By varying the length of time for testing as well as the temperature of the …

A Foundational Approach To Extrusion And Compounding, David Frankart

Williams Honors College, Honors Research Projects

With a history of nearly 200 years, polymer processing and compounding is constantly changing to fit the material science needs of the era. Exposure of undergraduate students to the technology and practices used in industry today in a lab setting would create new opportunities for experiential learning and growth. The objective was to set up a 0.75”, 25 L/D Thermo Haake single screw extruder for lab use and run trials of material in a single screw extruder to set up a basis for experiments. Trials were run of co-polyester resin through a single screw extruder with carbon fiber additives varying …

Impact Of Increased Precipitation On Midwestern Construction, Monica Feltman

Williams Honors College, Honors Research Projects

This paper presents the current impact of increased precipitation in the Midwest on the construction industry. Mainly, the impact on jobsite safety, increasing insurance rates, and the resulting changes in design codes, or lack thereof. The goal of this independent research is to gather a better understanding of the influence of these changes, because only then can one accurately seek to combat their harmful effects. As a vital element of the global economy, the construction industry must be conscious of their changing relationship with the environment around them. Therefore, understanding the affects of harmful climate change, will increase awareness of …