Engineering Commons^™

Comparison Of Reynolds-Averaged Navier-Stokes Turbulence Models For Simulating Boundary Layers In Hypersonic Flows, Jorge-Valentino Kurose Bretzke

Masters Theses

“This study describes the use of Computational Fluid Dynamics (CFD) codes to simulate hypersonic boundary layers using several different turbulent closure models and comparing Reynolds-Averaged Navier-Stokes (RANS) simulations against Direct Numerical Simulations (DNS) of similar test cases. The test cases in this study consist of a flat plate in a Mach 8 freestream with a zero pressure gradient and wall recovery ratio of 0.48, as well as a Mach 8 axisymmetric nozzle also with a cold wall. The RANS models used in this study are the Spalart-Allmaras model, Baldwin-Lomax model, Menter K-Omega Baseline and Menter K-Omega Shear Stress Transport models. …

Characterization Of A Plasma Source Simulating Solar Wind Plasma In A Vacuum Chamber, Blake Anthony Folta

Masters Theses

"The United States has set an aggressive time line to not only return to the Moon, but also to establish a sustained human presence. In the Apollo missions dust was a significant factor, but the duration of those missions was short so dust and surface charging were problems, but they did not pose an immediate threat. For a long-term mission, these problems instead become incredibly detrimental. Because of this, research needs to be conducted to investigate these phenomena so that mitigation techniques can be developed and tested. To this end, this thesis serves to demonstrate the Gas and Plasma Dynamics …

On The Investigation Of Hot Tearing Behavior Of Continuous Cast Steel, Yanru Lu

Masters Theses

”Hot tearing has long been recognized as a major problem that plagues the development of the continuous casting process and results in low-quality products. Understanding of the mechanisms and the required conditions for the hot tearing formation is important for industries but has not been well-established yet. Thus, this research focuses on the hot tearing issue observed in continuous cast steel, by providing a summary of the current research progress and then introducing a new laboratory method to determine the thermo-mechanical properties relevant to hot tearing of different steel grades under different solidification conditions. In this method, an apparatus was …

Micro-Analysis Of Contaminants In Suspended Load And Bank Deposits From The Mineral Fork Creek Watershed In Potosi, Missouri, 2019-2020, William Joseph Miller

Masters Theses

”There are rising concerns pertaining to water contamination produced by toxic heavy metal contaminants such as lead and zinc. For this study, lead, zinc, and barite are three identified contaminants currently threatening Missouri water supplies. A microanalysis of the amounts of lead, zinc, and barite in the water of Mineral Fork Creek was conducted, involving both field and laboratory work. The purpose of the study was to determine the levels of lead, zinc, and barite contaminants, contributing to Big River, by Mineral Fork Creek, in Potosi Missouri, Washington County.

This research study uses a quantitative micro-analysis approach to determine the …

Performance Evaluation Of Alsi10mg Fabricated By A Selective Laser Melting Process, David Michael Murphy

Masters Theses

“Selective laser melting is becoming a widely used additive manufacturing technique that melts metal powder in a layer by layer process in order to build a desired part or geometry. Like many additive processes, selective laser melting allows for fabrication of parts with complex geometries. In order to fabricate a fully dense part there are a number of variables to take into account including: powder characteristics, laser parameters, and environmental parameters. Each of these variables can affect the microstructure and thus the mechanical performance of an additively manufactured part. In this work, the aluminum alloy AlSi10Mg was investigated. AlSi10Mg is …

Optical Fiber Based Integrity Test Of Civil Engineering Materials: Numerical Analysis, Ruoyu Zhong

Masters Theses

“Major advancement in Civil Engineering cannot be accomplished without the help of sensors. Among different types of sensors, fiber-optic sensor is known for its light weight, high accuracy, resolution, immunity to electromagnetic interference, and resistance to harsh environment. This research mainly focuses on fiber-optic sensor application on concrete structures as temperature sensor. Thermal Integrity Profiling (TIP) is a non-destructive integrity testing method which makes use of the hydration heat from the concrete curing process to detect defects within a drilled shaft. Any defect of concrete could result in a temperature anomaly in a drilled shaft. The accuracy of the current …

Additive Manufacturing Of Linear Shaped Charges To Address Run Up And Run Down Phenomena, Jason Ho

Masters Theses

”A shaped charge is an explosive device used to focus detonation energy in a desired direction. Additive Manufacturing (AM) can allow greater design freedom and geometric complexity for the liner portion of the shaped charge.

In this work, the following hypotheses were tested: 1) Adjusting the initial apex angle of a linear shaped charge liner reduces the amount of run up that occurs, and 2) implementing a backstop at the end of a linear shaped charge liner reduces the amount of run down that occurs.

Linear shaped charge liners with a continuously changing apex angle were created with additive manufacturing. …

Mid-Infrared Chiral Metsurface Coupling With Molecular Vibration, Md Shamim Mahmud

Masters Theses

“The mid-infrared design of chiral metamaterial shows a tremendous absorption capability of infrared rays, and it has the significant application of circular dichroism based device development. Plasmon-phonon coupling is one of the application of metamaterial that provides a new path for tailoring the surface in the nanoscale, which is also applicable in molecules detection. It is possible to change the Plasmon-Phonon coupling strength not only through the chemical change of molecules but also by changing the metamaterial light-matter interaction property. So far, linearly polarized light shows the strong coupling between metamaterial and molecules. However, it is possible to observe strong …

Feasibility Study On Novel Fire-Resistant Coating Materials, Anyou Zhu

Masters Theses

“Over the past decades, wildfires in the United States have caused severe damage and property losses. The California Camp Fire in November 2018 caused 85 civilian fatalities and destroyed 18,793 structures. There is a need to enhance the fire resistance of structures and buildings. The primary purpose of this study was to develop innovative surface-bonded fire-resistant material that can be used as a wall coating with three primary features: (a) workability for application, (b) enough adhesion to the surface of the structure, (c) fire-resistant. This research developed mix designs of innovative fire-resistant coating materials including high-performance cement mortar (HPCM), geopolymer …

Design And Comparison Of Unoptimized And Optimized Gray Code Multi-Level Systems, Shirly Adams Gamliel

Masters Theses

“As the conventional binary MOS-based VLSI technology is reaching limitations in chip area, speed, and power, new technologies are being researched. Some such technologies relate to multi-level logic design. This thesis explores the process and benefits of applying and optimizing multi-level design techniques to an existing Gray code binary system. Specifically, the multi-level system is designed using CoreMem technology and is optimized using Indira Dugganapally’s optimization techniques.

The first step is generating the n-bit binary and quaternary truth tables for an encoder’s Gray code output and additional desired data. Then, the data for each n-bit system is arranged in multi-level …

Combining Laser Aided Ablation And Polishing To Minimize Surface Roughness Of Additively Manufactured Aluminium Components, Sahil Bipinkumar Patel

Masters Theses

“The surface roughness of additively manufactured parts is much higher than the acceptable range for most applications, thus post-processing is needed to qualify these parts for use. Laser polishing can be used to bring the surface roughness in an admissible range, but if the initial roughness is very high then the energy density for the polishing process needs to be very high to achieve a significant reduction in roughness. This high energy density can produce many process defects. Also, laser polishing alone cannot get rid of high wavelength asperities. Any waviness in the part can be linked with initial waviness …

Modal Analysis As Non-Destructive Testing Technique For Additively Manufactured 304l Stainless Steel Parts, Tristan N. Cullom

Masters Theses

“Non-Destructive Testing (NDT) methods for Additively Manufactured (AM) parts is an ongoing field of research in the additive community due to its ability to determine if a part can be deemed viable for field usage. This study presents modal analysis as a NDT method for AM parts. For production builds that have multiple copies of the same part, a correcting technique can be used such that the frequencies of the parts under test can be reliably compared against each other, which saves both time and money compared to other traditional NDT methods. This study was able to develop a novel …

3d Printing Reinforced Concrete Structures, Bryce Tyler Tafolla

Masters Theses

"This study aims to investigate a 3D printing method to directly incorporate continuous reinforcement into concrete structures. The ability to design and produce complex structures with optimized topographical configuration can be used to reduce potential material waste while maintaining the required structural strength. Furthermore, the ability to actively incorporate reinforcement into printed members substantially reduces potential labor requirements and eliminates the need to set up formwork.

The study began its initial approach with a manual extrusion process containing reinforcement to observe the necessary constraints required to achieve a printing system with this functionality. The second stage of development was designing …

Catalytic Utilization Of Carbon Dioxide As Renewable Feedstock For Production Of Chemicals And Fuels, Abbas Alaa Jawad

Doctoral Dissertations

"The utilization of CO₂ as a renewable feedstock for producing commodity chemicals and fuels is an interesting challenge to explore new concepts and opportunities in catalysis and industrial chemistry. This sustainable approach not only leads to production of useful chemicals, but also has the potential to mitigate anthropogenic CO₂ emissions to the atmosphere. CO₂ itself is a sustainable and inexhaustibly available carbon source, however, it is inextricably linked to its inherent inertness. It is a thermodynamically stable molecule (ΔG_f = -394.01 kJ.mol^-1) with high oxidation state, hence, reactions of CO₂ must be combined …

Thermodynamic Investigations Of Pure And Blended Cement Mixtures, Jonathan Lapeyre

Doctoral Dissertations

” This research is made up of several studies. The first study focused on understanding the reaction kinetics of Ca₃SiO₅ and metakaolin (MK) mixtures compared to Ca₃SiO₅ and silica fume (SF) mixtures. It was shown that MK was a more effective additive than SF at small replacement levels (i.e. ≥ 10% by mass) while higher replacement levels of MK became a detriment due to excess (Al(OH)₄¯) ions preventing the nucleation and growth of C-S-H. In a follow-up study where the MK particle size distribution (PSD) was modified, similar effects were observed but …

Polymeric Nanoparticle As A New Platform For High Removal Of Endotoxins From Biopharmaceutical Solutions, Sidharth Razdan

Doctoral Dissertations

"Presently, approximately one-third of all biopharmaceutical drugs are derived from biological sources like gram-negative bacteria. Gram-negative bacteria like E.coli are much cheaper to cultivate and provide higher biotherapeutic yield compared to mammalian cells. On extracting the useful biotherapeutics from the gram-negative bacterial cells (E.coli), endotoxin present in the bacteria is released in the surrounding media thus contaminating the lifesaving biotherapeutics. Application of the endotoxin-contaminated therapeutics to humans or animals can cause serious health issues like septic shock, tissue injury and ultimately death. Hence, thorough purification of biotherapeutics before parenteral application is necessary. Although there are multiple methods for …

Characterization Of Neutron Irradiated Accident Tolerant Nuclear Fuel Cladding Silicon Carbide & Radiation Detector Deadtime, Bader Almutairi

Doctoral Dissertations

“In part I, the pulse shape characteristics generated by a Geiger Muller (GM) detector and recorded by an oscilloscope manually, were investigated. The objective of part I was (1) to find a correlation between pulse shape and the operating voltage; and (2) to assess if pulse shape properties followed distinct patterns comparable to detector deadtime findings reported by a previous study. It was observed that (1) there is a strong correlation between pulse shape and operating voltage, and (2) pulse shape falls in three distinct regions similar to detector deadtime. Furthermore, parts II and III are companions and share the …

Effect Of Turbulence Model Closure Coefficient Uncertainty On Scramjet Flow Field Analysis, Martin Albert Di Stefano

Doctoral Dissertations

“The numerical modeling of supersonic combustion ramjet (scramjet) engine flow paths plays an important role in the design of hypersonic air-breathing propulsion systems. Due to the complexity of the flow field physics and limited experimental data, numerical models possess uncertainties which should be addressed to improve the prediction accuracy of the simulations. In this study, the effect of turbulence model closure coefficient uncertainty on the Reynolds-averaged Navier-Stokes solution of a scramjet isolator and scramjet strut fuel injector flow field is investigated with an uncertainty quantification and sensitivity analysis study for commonly used turbulence models. Turbulence models considered in this work …

Generalization Of Polynomial Chaos For Estimation Of Angular Random Variables, Christine Louise Schmid

Doctoral Dissertations

“The state of a dynamical system will rarely be known perfectly, requiring the variable elements in the state to become random variables. More accurate estimation of the uncertainty in the random variable results in a better understanding of how the random variable will behave at future points in time. Many methods exist for representing a random variable within a system including a polynomial chaos expansion (PCE), which expresses a random variable as a linear combination of basis polynomials.

Polynomial chaos expansions have been studied at length for the joint estimation of states that are purely translational (i.e. described in Cartesian …

An Emi Characterization And Modeling Study For Consumer Electronics And Integrated Circuits, Chunyu Wu

Doctoral Dissertations

“As internet-of-things (IoT) applications surge, wireless connectivity becomes an essential part of the network. Smart home, one of the most promising application scenarios of IoT, will improve our life quality enormously. However, electromagnetic interference (EMI) to the receiving antenna, either from another electronic product or from a module/an integrated circuit(IC) inside the same wireless device, will degrade the performance of wireless connectivity, thus influencing the user experience. Characterization and modeling of the EMI become increasingly important.

In the first part, an improved method to extract equivalent dipoles from magnitude- only electromagnetic-field data based on the genetic algorithm and back-and-forth iteration …

Investigation On Nanoparticle Based Combination Therapy For Targeted Cancer Treatment, Muhammad Raisul Abedin

Doctoral Dissertations

“The current treatment methods in cancer are associated with toxicity in healthy tissues, partial therapeutic response, drug resistance and finally recurrence of the disease. The cancer drugs are challenged by non-specific binding, undesired toxicity in healthy cells, low therapeutic index and finally poor therapeutic outcome. In this work, a targeted nanoscale therapeutic system Antibody Drug Nanoparticle (ADN) was engineered to selectively inhibit the breast cancer cell growth with reduced toxicity in healthy cells. The ADNs were designed by synthesizing rod shaped anoparticles using pure chemotherapeutic drug and covalently conjugating a therapeutic monoclonal antibody (mAb) on the surface of the drug …

Lateral-Torsional Buckling Strength Of Two-Span Glass Fiber Reinforced Polymer Beams, Mojtaba B. Sirjani, Zia Razzaq

Civil & Environmental Engineering Faculty Publications

This paper presents the outcome of a study of two-span glass fiber reinforced polymer (GFRP) I-section beams susceptible to lateral-torsional buckling when subjected to gradually increasing concentrated vertical load(s) in the presence of two different types of lateral bracing schemes. It is found that loading one span results in a smaller buckling load as compared with the cases with loading in both spans regardless of the type of bracing scheme used. Also, the study shows that the addition of midspan braces for the GFRP beams results in up to 5.5 times increase in the buckling load capacity.

Seismic Response Mitigation Of Base-Isolated Buildings, Mohammad Hamayoun Stanikzai, Said Elias, Rajesh Rupakhety

Civil & Environmental Engineering Faculty Publications

Earthquake response mitigation of a base-isolated (BI) building equipped with (i) a single tuned mass damper at the top of the building, (ii) multiple tuned mass dampers (MTMDs) at the top of the building, and (iii) MTMDs distributed on different floors of the building (d-MTMDs) is studied. The shear-type buildings are modeled by considering only one lateral degree of freedom (DOF) at the floor level. Numerical approach of Newmark's integration is adopted for solving the coupled, governing differential equations of motion of 5- and 10-story BI buildings with and without TMD schemes. A set of 40 earthquake ground motions, scaled …

Resource Ecologies, Political Economies And The Ethics Of Audio Technologies In The Anthropocene, Eliot Bates

Publications and Research

Understanding how recorded and amplified stage musics contribute towards producing the Anthropocene necessitates attending to complex transnational flows of material, capital and labor, and how they coalesce into technological objects. This is complicated by the wide array of sites, practices and knowledges involved during various stages of the production process, from initial resource extraction, to smelting, component manufacturing, technology assembly, and distribution. To develop a suitable technological ethics, and to understand what happens to environments and to human, animal and plant lifeworlds, requires one to resist abstraction and undertake a global accounting of resource ecologies with recourse to planetary-scale political …

Structural And Environmental Impact Of New-Generation Wide-Base Tires In New Brunswick, Canada, Izak M. Said, Jaime Hernandez, Seunggu Kang, Imad L. Al-Qadi

Civil and Environmental Engineering Faculty Research and Publications

The loading and environmental impacts of new-generation wide-base tires (NG-WBT) and dual tire assemblies (DTA) on typical asphalt concrete (AC) pavement sections of New Brunswick, Canada were evaluated using finite element method (FEM) analysis and life-cycle assessment. The impact of steering wheel was not considered in this study. The analysis considered realistic material models and loading conditions (i.e. AC viscoelastic characteristics and measured three-dimensional nonuniform tire–pavement contact loads). Predicted critical pavement responses were used in transfer functions to determine potential pavement damage. The NG-WBT loading resulted in greater critical pavement responses compared to that of DTA, especially near the surface …

Assessing The Impact Of Ires On Researchers, Research Outcomes, And Students: A Case Study Approach, David B. Knight, Nicole Sanderlin, Kirsten A. Davis

School of Engineering Education Faculty Publications

IRES programs seek to develop globally connected future researchers while also facilitating broader long-term collaborations between U.S.-based and international research groups. Faculty and student exchanges are expected to result in international linkages between the researchers that bring new insights and methods to U.S.-based research projects, leading to transformative research. In this project, we conducted a comprehensive evaluation of IRES programs through a case study analysis. The nine selected cases focused specifically on engineering-focused IRES experiences for ease of comparison. Case studies included interviews with all U.S. PI’s, a selection of additional international and U.S. faculty researchers, and select student alumni …

The Role Of Geospatial Information And Effective Partnerships In The Implementation Of The International Agenda For Sustainable Development, Etta Delores Jackson

Antioch University Dissertations & Theses

The former United Nations Secretary-General Ban Ki-Moon (2014), repeated the core promise in the 1986 UN Declaration on the Right to Development, in which the General Assembly called for an approach guaranteeing meaningful participation of everyone in development and the fair distribution of the benefits of that development. To this end, partnerships are central and can lead to the dignity of the citizens involved as they participate in the development of their own communities. This dissertation research conducted in Manyatta A and B in the Port City of Kisumu, Kenya sought to do just that. The purpose of this study …

Arising: Hurricane (Superstorm) Sandy’S Impact On Design/Planning Professionals, Maxinne R. Leighton

Antioch University Dissertations & Theses

Standing by my bedroom window, looking out at the ocean, a huge wave comes and swallows up my building. Everything around me is gone, including me. I wake up. I am 13 years old and living in the Coney Island Houses on Surf Avenue, Brooklyn, New York. With ongoing anthropogenic changes to the natural environment such as sea level rise and intensifying storms, coastal communities, especially ones segregated by class and culture, are particularly vulnerable in this context that challenges a way of life, and in some instances, threatens that life's survival. This dissertation focuses specifically on what one massive …

A Comparative Study Of Text Summarization On E-Mail Data Using Unsupervised Learning Approaches, Tijo Thomas

Dissertations

Over the last few years, email has met with enormous popularity. People send and receive a lot of messages every day, connect with colleagues and friends, share files and information. Unfortunately, the email overload outbreak has developed into a personal trouble for users as well as a financial concerns for businesses. Accessing an ever-increasing number of lengthy emails in the present generation has become a major concern for many users. Email text summarization is a promising approach to resolve this challenge. Email messages are general domain text, unstructured and not always well developed syntactically. Such elements introduce challenges for study …

Evaluating Bert Embeddings For Text Classification In Bio-Medical Domain To Determine Eligibility Of Patients In Clinical Trials, Saurabh Khodake

Dissertations

Clinical Trials are studies conducted by researchers in order to assess the impact of new medicine in terms of its efficacy and most importantly safety on human health. For any advancement in the field of medicine it is very important that clinical trials are conducted with right ethics supported by scientific evidence. Not all people who volunteer or participate in clinical trials are allowed to undergo the trials. Age, comorbidity and other health issues present in a patient can be a major factor to decide whether the profile is suitable or not for the trial. Profiles selected for clinical trials …