Engineering Commons^™

Sustainable And Resilient Construction: Current Status And Future Challenges, Niamh Murtagh, Lloyd Scott, Jingli Fan

Articles

The construction industry globally is one of the most environmentally damaging of sectors. Additionally, the resources consumed and the operational energy requirements of buildings are ‘locked-in’, potentially for decades. The Intergovernmental Panel on Climate Change has recognised construction as a sector in which significant improvements can, and indeed must, be made. But the industry is often argued to be unique, in its multiplicity of stakeholders, transient organisational structures, avoidance of risk and impact on society. The current Virtual Special Issue (VSI) sought to bring together a collection of papers on progress and potential for improvement in the construction sector, in …

Thermal Analysis And Post Construction Verification, Cormac Flood, Lloyd Scott

Articles

Purpose – The residential sector in Ireland accounted for 25 per cent of energy related CO2 emissions in 2016 through burning fossil fuels, a major contributor to climate change. In support of Ireland’s CO2 reduction targets, the existing housing stock could contribute greatly to the reduction of space-heating energy demand through retrofit. Approximately 50 per cent of Ireland’s 2m dwellings pre-date building regulations and are predominantly of cavity and solid wall construction, the performance of which has not been extensively investigated at present. Although commitment to thermal upgrade/retrofit of existing buildings may increase under future government policies, the poor characterisation …

Mapping The In-Plane Electric Field Inside Irradiated Diodes, L. Poley, A.J. Blue, C. Buttar, V. Cindro, C. Darroch, V. Fadayev, J. Fernandez-Tejero, C. Fleta, C. Helling, C. Labitan, I. Mandic, S.N. Santpur, D. Sperlich, M. Ullan, Y. Unno

Articles

A significant aspect of the Phase-II Upgrade of the ATLAS detector is the replacement of the current Inner Detector with the ATLAS Inner Tracker (ITk). The ATLAS ITk is an all-silicon detector consisting of a pixel tracker and a strip tracker. Sensors for the ITk strip tracker have been developed to withstand the high radiation environment in the ATLAS detector after the High Luminosity Upgrade of the Large Hadron Collider at CERN, which will significantly increase the rate of particle collisions and resulting particle tracks. During their operation in the ATLAS detector, sensors for the ITk strip tracker are expected …

Indirect Sliding Mode Control For Dc-Dc Sepic Converters, Hasan Komurcugil, Samet Biricik, Naki Guler

Articles

This article presents an indirect sliding mode control (SMC) for single-ended primary-inductor converters (SEPIC). Unlike the conventional SMC methods, the proposed SMC method employs a sliding surface function based on the input current error only. The use of such sliding surface function not only simplifies the implementation but also reduces the cost of implementation. It is shown that the output voltage control can be achieved indirectly. The input current reference is generated by a proportional-integral (PI) regulator. The existence condition and the region of the closed-loop system are determined for all possibilities of the PI gains. The performance of the …

A Closed-Loop Renewable Energy Evaluation Framework, Tony Kealy

Articles

Many businesses that have embraced renewable energy projects as part of their corporate sustainability efforts lack direction concerning how the projects are assessed. This study presents a framework that prescribes the necessary stages that allow a robust project evaluation to take place. The framework should assist practitioners in ascertaining if renewable energy projects, such as wind turbines and hydroelectric generators, contribute to energy cost savings and a reduction in CO2 emissions. The conceptual framework was developed using empirical data accessed from an 850-kW wind turbine case study and a 40-kW hydro-electric case study and embraced the action research methodology. Both …

Vehicle-To-Grid Integration For Enhancement Of Grid: A Distributed Resource Allocation Approach, Deepak Tiwari, Mohd Adil Anwar Sheikh, Joseph Moyalan, Mayur Sawant, Sarika Khushalani Solanki, Jignesh Solanki

Faculty & Staff Scholarship

In the future grids, to reduce greenhouse gas emissions Electric Vehicles (EVs) seems to be an important means of transportation. One of the major disadvantages of the future grid is the demand-supply mismatch which can be mitigated by incorporating the EVs into the grid. The paper introduces the concept of the Distributed Resource Allocation (DRA) approach for incorporating a large number of Plug-in EV (PEVs) with the power grid utilizing the concept of achieving output consensus. The charging/discharging time of all the participating PEVs are separated with respect to time slots and are considered as strategies. The major aim of …

Predicting Fracture Extension Around A Borehole Using The Numerical Displacement Discontinuity Method, Nathaniel Schaefer

Theses and Dissertations--Mining Engineering

Prediction of blast damage radius is integral in the optimization of mining safety and production. The damage radius can be related to blasting variables such as fragmentation size as well as overbreak in hard rock. Various methods have been developed to predict and assess damage radius extension for individual holes to aid in blast design. These methods range from experimental and observational techniques to theoretical applications. Some of these methods have been used with a degree of success. However, many of them lack a comprehensive combination of experimental and theoretical contributions. Since post-blast environments are not conducive to assessing whether …

Proof Of Concept For The Development Of A Ground Vibration Sensor System For Future Research In Blasting, John Meuth

Theses and Dissertations--Mining Engineering

Ground vibrations from blasting are one of the leading limitations to mining (underground and surface). There is a need for a low-cost scalable vibration monitoring system to conduct large scale ground vibration projects in the mining industry. Studies conducted on ground vibrations use any number of different sensors to obtain their data, the different sensor capabilities and methods for data processing lead to uncertainties in the research and regulations set for ground vibrations. Commercial Systems do not allow researchers to obtain raw output data, and the data processing procedures are not provided or disclosed for these systems. In order to …

The Effect Of Delay And Sequence On Blasting Fragmentation Results, Tristan Worsey

Theses and Dissertations--Mining Engineering

Blasters use the delay between charges and the firing sequence of the explosive charges to help reduce vibrations and achieve the desired fragmentation. Although delay and sequence are recognized as very important for vibrations and fragmentation, only vibration models consider timing as a variable in the prediction tool, without any known model for fragmentation prediction based on the delay sequence. Of the few fragmentation models available, very few take delay into account and do not give guidance on row delay and/or sequence selections. With the invention of electronic detonators in 1984, there are new avenues to explore with sequence and …

Operation And Analysis Of High-Voltage-Gain Dc-Dc Converters With Voltage Multipliers, Mohammad Rashed M. Altimania

Doctoral Dissertations

"This research analyzes and investigates the steady-state operations of four different high-voltage-gain step-up dc- dc converters to achieve a high gain. These topologies consist of a two-phase interleaved boost stage with three various voltage multiplier (VM) stages. The first stage of the first three topologies is the same, which is a two-phase interleaved boost stage implemented by using inductors. The first family used in this research is based on a modified Dickson charge pump voltage multiplier stage, and this family has been studied in discontinuous conduction mode (DCM). The second family relies on a non-inverting or inverting diode-capacitors voltage multiplier …

Forming And Processing Of Advanced Fiber Reinforced Polymer Composites, Robert Meinders

Doctoral Dissertations

“Composite materials are commonly used in industry to manufacture strong and lightweight structures. Composites feature a large degree of flexibility in materials selection and manufacturing processes to tailor the strength of manufactured parts. This study examines different manufacturing aspects of composites. In Part I, the fabrication of composite parts using the compression forming process is examined. During compression forming, metal dies are used to apply large deformations to prepreg material to fabricate composite parts. The high stresses and deformations of this process can yield manufacturing defects. T650/5320-1 prepreg is subjected to material characterization to develop simulations of large deformation forming …

Towards Overcoming The Curse Of Dimensionality In Predictive Modelling And Uncertainty Quantification, Dan Gabriel Cacuci

Faculty Publications

This invited presentation summarizes new methodologies developed by the author for performing high-order sensitivity analysis, uncertainty quantification and predictive modeling. The presentation commences by summarizing the newly developed 3rd-Order Adjoint Sensitivity Analysis Methodology (3rd-ASAM) for linear systems, which overcomes the “curse of dimensionality” for sensitivity analysis and uncertainty quantification of a large variety of model responses of interest in reactor physics systems. The use of the exact expressions of the 2nd-, and 3rd-order sensitivities computed using the 3rd-ASAM is subsequently illustrated by presenting 3rd-order formulas for the first three cumulants of the response distribution, for quantifying response uncertainties (covariance, skewness) …

On The Importance Of Second-Order Response Sensitivities To Nuclear Data In Reactor Physics Uncertainty Analysis, Dan Gabriel Cacuci

Faculty Publications

This invited keynote presentation compares the relative importance of 1st-order versus 2nd-order sensitivities of the leakage response of an OECD/NEA benchmark (polyethylene-reflected plutonium sphere) to the nuclear data characterizing this benchmark. The imprecisely known parameters underlying the neutron transport computational model for this benchmark include 180 group-averaged total microscopic cross sections, 21600 group-averaged scattering microscopic cross sections, 60 parameters describing the fission process, 30 parameters describing the fission spectrum, 10 parameters describing the system's sources, and 6 isotopic number densities. Thus, this benchmark comprises 21886 1st-order sensitivities of the leakage response with respect to the model parameters, and 478,996,996 2nd-order …

Test 2217: Kubota M8-181, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2218: Kubota M8-201, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2219: John Deere 7r 290, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2225: John Deere 8rt 370, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2226: John Deere 8rt 410, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary 1197: John Deere 6195m Ft4, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary 1195: John Deere 6155m Ft4, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary 1196: John Deere 6175m Ft4, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary 1192: John Deere 6120m Ft4, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary 1191: John Deere 6110m Ft4, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Using Geothermal Energy To Reduce Oil Production Costs, Will Gosnold, Mark Ballesteros, Dongmei Wang, Josh Crowell

Geology and Geological Engineering Faculty Publications

The economic impact of the Covid-19 pandemic on the oil industry has been devastating. The decline in demand and price collapse have been particularly disruptive for shale oil extraction which is inherently more expensive than conventional operations. Survival and continuing operations will depend partly on reducing operating costs, and a ubiquitous and substantial cost in oil production is electrical power used primarily for pumping the wells. The Bakken in North Dakota play is particularly vulnerable because there is not an adequate electrical grid in the region. Many Bakken fields rely on generators burning propane, gasoline or diesel fuel at costs …

Ultrahigh Strength And Plasticity In Laser Rapid Solidified Al–Si Nanoscale Eutectics, Huai-Hsun Lien, Jyoti Mazumder, Jian Wang, Amit Misra

Department of Mechanical and Materials Engineering: Faculty Publications

As-cast Al–20wt.% Si alloys were processed via laser rapid solidification (LRS) techniques to create eutectic microstructures with nanoscale interconnected, nanotwinned Si fibers. LRS morphologies exhibit higher flow stress, exceeding 800 MPa and uniform plastic deformation above 20% compared to as-cast alloy that fractures at strains below 8% at flow strength of approximately 200 MPa. The strengthening mechanisms of LRS morphologies are interpreted in terms of the interfacial constraints: increase in yield strength as well as strain hardening rate due to nanoscale confined slip in fibrous Al–Si eutectic, and load transfer and eventual plasticity in the nanoscale Si fibers.

Leidenfrost Droplet Microfluidics, Sidy Ndao, George Gogos, Dennis Alexander, Troy Anderson, Craig Zuhlke

Department of Mechanical and Materials Engineering: Faculty Publications

Systems and methods are described for propelling a liquid droplet in a Leidenforst state. A microfluidic device embodiment includes, but is not limited to, a solid structure having a patterned surface, the patterned surface including at least a first patterned region having a first Leidenfrost temperature with respect to a fluid, the first patterned region adjacent to the second patterned region, the first patterned region defining a path over which a droplet of the fluid is configured to travel in a Leidenfrost state.

Iron Pyrite Nanocrystals, Jinsong Huang, Baodong Mao, Christopher L. Exstrom

Department of Mechanical and Materials Engineering: Faculty Publications

An apparatus includes a nanocrystal. The nanocrystal includes a core including FeS2; and a coating including a ligand component capable of chemically interacting with both an iron atom and a sulfur atom on a surface of the core.

Colocalized Sensing And Intelligent Computing In Micro-Sensors, Mohammad H. Hasan, Ali Al-Ramini, Eihab Abdel-Rahman, Roozbeh Jafari, Fadi Alsaleem

Department of Mechanical and Materials Engineering: Faculty Publications

This work presents an approach to delay-based reservoir computing (RC) at the sensor level without input modulation. It employs a time-multiplexed bias to maintain transience while utilizing either an electrical signal or an environmental signal (such as acceleration) as an unmodulated input signal. The proposed approach enables RC carried out by sufficiently nonlinear sensory elements, as we demonstrate using a single electrostatically actuated microelectromechanical system (MEMS) device. The MEMS sensor can perform colocalized sensing and computing with fewer electronics than traditional RC elements at the RC input (such as analog- to-digital and digital-to-analog converters). The performance of the MEMS RC …

Microstructural Evolution Of Nanotwinned Al-Zr Alloy With Significant 9r Phase, N.A. Richter, Y.F. Zhang, D. Y. Xie, R. Su, Q. Li, S. Xue, T. Niu, J. Wang, H. Wang, Xinghang Zhang

Department of Mechanical and Materials Engineering: Faculty Publications

Aluminum (Al) alloys have a multitude of applications, notably in the automotive, aerospace and coating industries, yet they exhibit significantly lower mechanical strength than conventional steels. Nanotwins drastically improve mechanical strength while retaining ductility. However, the high SFE of Al largely prevents twinning. Here, we synthesize Al-Zr alloy films containing an abundance of incoherent twin boundaries and 9R phases. These alloys exhibit an extended solid solubility of Zr, retaining a columnar nanotwinned structure across all compositions. These films reach a hardness up to 4.2 GPa with 10 at% Zr and demonstrate the capacity for producing strong Al alloys with nanotwins.

Standardization Roadmap For Unmanned Aircraft Systems, Version 2.0, Kristine Kiernan, Robert Joslin, John Robbins

Publications

This Standardization Roadmap for Unmanned Aircraft Systems, Version 2.0 (“roadmap”) is an update to version 1.0 of this document published in December 2018. It identifies existing standards and standards in development, assesses gaps, and makes recommendations for priority areas where there is a perceived need for additional standardization and/or pre-standardization R&D.

The roadmap has examined 78 issue areas, identified a total of 71 open gaps and corresponding recommendations across the topical areas of airworthiness; flight operations (both general concerns and application-specific ones including critical infrastructure inspections, commercial services, and public safety operations); and personnel training, qualifications, and certification. Of that …