Engineering Commons^™

3d Interdigitated Vertically Aligned Carbon Nanotube Electrodes For Electrochemical Impedimetric Biosensing, Benjamin J. Brownlee, Jonathan C. Claussen, Brian D. Iverson

Faculty Publications

Advances in nanomaterials, combined with electrochemical impedance spectroscopy (EIS), have allowed electrochemical biosensors to have high sensitivity while remaining labe-lfree, enabling the potential for portable diagnosis at the point-of-care. We report porous, 3D vertically aligned carbon nanotube (VACNT) electrodes with underlying chromium electrical leads for impedance-based biosensing. The electrodes are characterized by electrode height (5, 25, and 80 μm), gap width (15 and 25 μm), and geometry (interdigitated and serpentine) using scanning electron microscopy, cyclic voltammetry, and EIS. The protein streptavidin is functionalized onto VACNT electrodes for detection of biotin, as confirmed by fluorescence microscopy. EIS is used to measure …

Application Of Satellite Remote Sensing In Monitoring Elevated Internal Temperatures Of Landfills, Rouzbeh Nazari, Husam Alfergani, Francis M. Haas, Maryam E. Karimi, Md Golam Rabbani Fahad, Samain Sabrin, Jess Everett, Nidhal Carla Bouaynaya, Robert W. Peters

Henry M. Rowan College of Engineering Departmental Research

Subsurface fires and smoldering events at landfills can present serious health hazards and threats to the environment. These fires are much more costly and difficult to extinguish than open fires at the landfill surface. The initiation of a subsurface fire may go unnoticed for a long period of time and undetected fires may spread over a large area. Unfortunately, not all landfill operators keep or publish heat elevation data and many landfills are not equipped with a landfill gas extraction system to control subsurface temperatures generated from the chemical reactions within. The timely and cost-effective identification of subsurface fires is …

An Explainable And Statistically Validated Ensemble Clustering Model Applied To The Identification Of Traumatic Brain Injury Subgroups, Dacosta Yeboah, Louis Steinmeister, Daniel B. Hier, Bassam Hadi, Donald C. Wunsch, Gayla R. Olbricht, Tayo Obafemi-Ajayi

Electrical and Computer Engineering Faculty Research & Creative Works

We present a framework for an explainable and statistically validated ensemble clustering model applied to Traumatic Brain Injury (TBI). The objective of our analysis is to identify patient injury severity subgroups and key phenotypes that delineate these subgroups using varied clinical and computed tomography data. Explainable and statistically-validated models are essential because a data-driven identification of subgroups is an inherently multidisciplinary undertaking. In our case, this procedure yielded six distinct patient subgroups with respect to mechanism of injury, severity of presentation, anatomy, psychometric, and functional outcome. This framework for ensemble cluster analysis fully integrates statistical methods at several stages of …

Survey Of Dc-Dc Non-Isolated Topologies For Unidirectional Power Flow In Fuel Cell Vehicles, Mahajan Sagar Bhaskar, Vigna K. Ramachandaramurthy, Sanjeevikumar Padmanaban, Frede Blaabjerg, Dan M. Ionel, Massimo Mitolo, Dhafer Almakhles

Power and Energy Institute of Kentucky Faculty Publications

The automobile companies are focusing on recent technologies such as growing Hydrogen (H2) and Fuel Cell (FC) Vehicular Power Train (VPT) to improve the Tank-To-Wheel (TTW) efficiency. Benefits, the lower cost, `Eco' friendly, zero-emission and high-power capacity, etc. In the power train of fuel cell vehicles, the DC-DC power converters play a vital role to boost the fuel cell stack voltage. Hence, satisfy the demand of the motor and transmission in the vehicles. Several DC-DC converter topologies have proposed for various vehicular applications like fuel cell, battery, and renewable energy fed hybrid vehicles etc. Most cases, the DC-DC power converters …

Factors Affecting Brittleness Behavior Of Coal-Gangue Ceramsite Lightweight Aggregate Concrete, Yunsen Wang, Jingping Qiu, Wen Deng, Jun Xing, Jian Liang

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Coal gangue, which is the solid waste produced during the coal processing, causes serious environmental problems. Lightweight concrete by making use of the coal-gangue ceramsite as the aggregate has many advantages as the construction material. However, the high brittleness of lightweight aggregate concrete is one of the problems for its application in building infrastructure. In this paper, the variation regularity, influencing factors and reinforcing/toughening method were studied as the reference data for future practical applications of coal-gangue ceramsite lightweight aggregate concrete (CGCLWAC). The results show that the brittleness of CGCLWAC increases with age, but the rate of the increase of …

Single‐Molecule 3d Orientation Imaging Reveals Nanoscale Compositional Heterogeneity In Lipid Membranes, Jin Lu, Hesam Mazidi, Tianben Ding, Oumeng Zhang, Matthew D. Lew

Electrical & Systems Engineering Publications and Presentations

In soft matter, thermal energy causes molecules to continuously translate and rotate, even in crowded environments, thereby impacting the spatial organization and function of most molecular assemblies, such as lipid membranes. Directly measuring the orientation and spatial organization of large collections (>3000 molecules μm⁻²) of single molecules with nanoscale resolution remains elusive. In this paper, we utilize SMOLM, single‐molecule orientation localization microscopy, to directly measure the orientation spectra (3D orientation plus “wobble”) of lipophilic probes transiently bound to lipid membranes, revealing that Nile red's (NR) orientation spectra are extremely sensitive to membrane chemical composition. SMOLM images resolve …

Hexacyanoferrate-Based Nanocomposites For The Electrochemical Sensing Of Hydrogen Peroxide And Nicotine, Lee Pui Kee

Student Works (2020-2029)

Metal hexacyanoferrate (MeHCF) is a unique material that not only acquired immense research interest in electrochemical sensing field but also possesses potential as energy storage material. As such, the present thesis sought to investigate the facile method to synthesis MeHCF-based nanocomposites and explore its possible applications. First, comparative research on the synthesis of Prussian blue-polypyrrole (PB-PPy) nanocomposite by novel self-assembly (SA) method and conventional electrodeposition technique was performed. PB-PPy nanocomposites were prepared by the novel self-assembly method and via the electrodeposition approach. The nanocomposites were compared in term of surface morphology and its electrochemical and electrocatalytic characteristics. The results indicated …

Indoor Air Quality Impacts Of A Woodstove Exchange Program In Washington County, Oregon, Matthew Forrest Survilo

Dissertations and Theses

More than six million people in the United States use wood stoves as their primary heat source. Wood stoves emit air pollutants that may impact health, e.g., wood combustion products are associated with premature death and aggravation of pulmonary and cardiovascular conditions. There are few studies investigating the efficacy of wood stove exchange programs (WSEPs) as a method to improve indoor air quality (IAQ). In partnership with Washington County Department of Health and Human Services we conducted an air quality study to measure the impact of a WSEP on indoor and neighborhood levels of wood combustion products. Twenty households engaged …

Anti-Collision Planning Optimization In Directional Wells, Abdulrahman Mohamed

Petroleum Engineering and Gas

One of the most application of the directional drilling is drilling multiple wells from one location or platform. In drilling multiple wells from one location the major problem that faced is avoiding the collision with the offset wells that drilled near the proposed well in the same region. Therefore, the potential of collison between the wells can cause severe catastrophic accidents such as an explosion or oil spill. Several measurements of proximity calculation or methods have been adopted to control the distance between the wells, avoid the collison, increasing the clearance along with smoothing the trajectory, Reducing the drilling time …

Unmanned Aerial System Integrated Sensor For Remote Gamma And Neutron Monitoring, Alexander Barzilov, Monia Kazemeini

Mechanical Engineering Faculty Research

Tools for remote radiation sensing are essential for environmental safety and nuclear power applications. The use of unmanned aerial systems (UASs) equipped with sensors allows for substantially reducing the radiation exposure of personnel. An ambient temperature Cs2LiYCl6:Ce3+ (CLYC) elpasolite scintillation sensor for simultaneous gamma and neutron measurements was designed as a user-friendly “plug and fly” module integrated into an octocopter robotic platform. Robot Operating System (ROS) was used to analyze the sensor’s data. The measured CLYC’s energy resolution was < 5% at 662 keV gamma rays; neutron flux was measured using6Li(n,α)t reaction. Time and GPS data were combined with radiation data in the ROS, supporting real time monitoring and assessment tasks, as well as radiation source search missions. Because UASs can be irradiated, radiation damage of the sensor and robot’s electronics was estimated using FLUKA code.

An Algorithm For Adaptive Determination Of Radar Coherent Integration Time, Jakob Delong, Joel T. Johnson

Electrical and Computer Engineering Faculty Research & Creative Works

A method for adaptively determining a desirable coherent integration time for radar observations of a moving clutter target is examined. A signal model appropriate for such measurements is first defined, along with an approach for estimating the coherence time from measured data. This coherence time estimate is then used as the coherent integration time in a reprocessing of the measured data. Simulations are shown that illustrate the potential advantages of this approach in reducing the variance of the clutter power estimate, particularly at low clutter to noise ratios, as compared to a purely incoherent integration. However, the initial correlation time …

Towards Distributed Recycling With Additive Manufacturing Of Pet Flake Feedstocks, Helen A. Little, Nagendra Gautam Tanikella, Matthew J. Reich, Matthew J. Fiedler, Samantha L. Snabes, Joshua M. Pearce

Michigan Tech Publications, Part 1

This study explores the potential to reach a circular economy for post-consumer Recycled Polyethylene Terephthalate (rPET) packaging and bottles by using it as a Distributed Recycling for Additive Manufacturing (DRAM) feedstock. Specifically, for the first time, rPET water bottle flake is processed using only an open source toolchain with Fused Particle Fabrication (FPF) or Fused Granular Fabrication (FGF) processing rather than first converting it to filament. In this study, first the impact of granulation, sifting, and heating (and their sequential combination) is quantified on the shape and size distribution of the rPET flakes. Then 3D printing tests were performed on …

Evaluation Of Impact Of Fiber Type And Dosage Rate On Volumetrics And Laboratory Performance Of Asphalt Mixtures, Ahmad G. M. Alfalah

Theses and Dissertations

The purpose of this study is to evaluate the impact of fiber types, binder content, and dosage rates on the volumetric properties and laboratory performance of asphalt mixtures. One asphalt mixture (control) and four fiber types (Fiberglass, Basalt, Carbon, and Polyolefin/Aramid) were used to evaluate the impact of fiber types and dosage rates. Two mixing procedures for introducing fibers into asphalt mixtures were also evaluated: dry and proportional dispersion methods. To evaluate the impact of fiber types, 0.16% by total mix weight was used. Rutting, cracking, and durability performance tests were evaluated. Furthermore, using 0.15% and 0.3% fiber dosage rates, …

3d-Printed Leg Design And Modification For Improved Support On A Quadruped Robot, Jasmin S. Collins

Maseeh Summer Undergraduate Research Experience

The Agile and Adaptive Robotics Lab aims to uncover the biological and physiological complexities in animal agility and adaptive control, which can be replicated through robotics and provide further applications in biology and medicine. One project within the lab focuses on understanding structure, actuation, and control through the modeling of a canine quadruped robot.

The AARL has developed a full-body quadruped robot with artificial muscles that control limb movement and a body that is built from 3D-printed parts. This specific project involved modification of these existing parts to (a) minimize deflections in the front legs, causing unwanted lateral and abduction/adduction …

Elementary Teachers’ Mental Images Of Engineers At Work, Rebekah Hammack, Juliana Utley, Toni Ivey, Karen High

Journal of Pre-College Engineering Education Research (J-PEER)

The purpose of the current study was to determine the impacts of a multiple-day engineering-focused professional development program on elementary teachers’ perceptions of the work of engineers and their use of mathematics and science. Data were collected in the form of drawings of engineers prior to and immediately after the professional development program as well as an open-ended exit survey at the end of the program. Participants’ drawings were scored in the following areas: use of mathematics, use of science, and work of an engineer. Wilcoxon signed-rank tests revealed that the only significant change between measures was in ‘‘work of …

Global Convergence Of Covid-19 Basic Reproduction Number And Estimation From Early-Time Sir Dynamics, Gabriel G. Katul, Asaad Mrad, Sara Bonetti, Gabriele Manolia, Anthony J. Parolari

Civil and Environmental Engineering Faculty Research and Publications

The SIR (‘susceptible-infectious-recovered’) formulation is used to uncover the generic spread mechanisms observed by COVID-19 dynamics globally, especially in the early phases of infectious spread. During this early period, potential controls were not effectively put in place or enforced in many countries. Hence, the early phases of COVID-19 spread in countries where controls were weak offer a unique perspective on the ensemble-behavior of COVID-19 basic reproduction number inferred from SIR formulation. The work here shows that there is global convergence (i.e., across many nations) to an uncontrolled R_o=4.5 that describes the early time spread of COVID-19. This value …

Additively Manufactured Parametric Universal Clip-System: An Open Source Approach For Aiding Personal Exposure Easurement In The Breathing Zone, Kirsi Kukko, Jan Sher Akmal, Anneli Kangas, Mika Salmi, Roy Björkstrand, Anna-Kaisa Viitanen, Jouni Partanen, Joshua M. Pearce

Michigan Tech Publications, Part 1

Design for additive manufacturing is adopted to help solve problems inherent to attaching active personal sampler systems to workers for monitoring their breathing zone. A novel and parametric 3D printable clip system was designed with an open source Computer-aided design (CAD) system and was additively manufactured. The concept was first tested with a simple clip design, and when it was found to be functional, the ability of the innovative and open source design to be extended to other applications was demonstrated by designing another tooling system. The clip system was tested for mechanical stress test to establish a minimum lifetime …

The Importance Of Collaborative Design For Narrowing The Gender Gap In Engineering: An Analysis Of Engineering Identity Development In Elementary Students, Mandy Mclean, Jasmine M. Nation, Alexis Spina, Tyler Susko, Danielle Harlow, Julie Bianchini

Journal of Pre-College Engineering Education Research (J-PEER)

Research suggests that, to narrow the gender gap in engineering, we should focus on helping young girls identify with engineering both because gendered attitudes emerge around kindergarten and because identity is more predictive than performance on persistence in the field. This qualitative study sought to understand the impact of collaborative engineering design on the development of engineering identities in elementary-school students and compared the findings across gender. We focused on three tiers of collaboration embedded into the engineering design process: peer groups, role models, and shared goals. More specifically, the elementary students worked in small teams and partnered with undergraduate …

Jump Linear Quadratic Control For Microgrids With Commercial Loads, Maryam Khanbaghi, Aleksandar Zečević

Electrical and Computer Engineering

Due to the aging power-grid infrastructure and increased usage of renewable energies, microgrids (μGrids) have emerged as a promising paradigm. It is reasonable to expect that they will become one of the fundamental building blocks of a smart grid, since effective energy transfer and coordination of μGrids could help maintain the stability and reliability of the regional large-scale power-grid. From the control perspective, one of the key objectives of μGrids is load management using local generation and storage for optimized performance. Accomplishing this task can be challenging, however, particularly in situations where local generation is unpredictable both in quality and …

A Century Of Observations Reveals Increasing Likelihood Of Continental-Scale Compound Dry-Hot Extremes, Mohammad Reza Alizadeh, Jan Adamowski, Mohammad Reza Nikoo, Amir Aghakouchak, Philip Dennison, Mojtaba Sadegh

Civil Engineering Faculty Publications and Presentations

Using over a century of ground-based observations over the contiguous United States, we show that the frequency of compound dry and hot extremes has increased substantially in the past decades, with an alarming increase in very rare dry-hot extremes. Our results indicate that the area affected by concurrent extremes has also increased significantly. Further, we explore homogeneity (i.e., connectedness) of dry-hot extremes across space. We show that dry-hot extremes have homogeneously enlarged over the past 122 years, pointing to spatial propagation of extreme dryness and heat and increased probability of continental-scale compound extremes. Last, we show an interesting shift between …

Autonomous Pev Charging Scheduling Using Dyna-Q Reinforcement Learning, Fan Wang, Jie Gao, Mushu Li, Lian Zhao

Electrical and Computer Engineering Faculty Research and Publications

This paper proposes a demand response method to reduce the long-term charging cost of single plug-in electric vehicles (PEV) while overcoming obstacles such as the stochastic nature of the user's driving behaviour, traffic condition, energy usage, and energy price. The problem is formulated as a Markov Decision Process (MDP) with an unknown transition probability matrix and solved using deep reinforcement learning (RL) techniques. The proposed method does not require any initial data on the PEV driver's behaviour and shows improvement on learning speed when compared to a pure model-free reinforcement learning method. A combination of model-based and model-free learning methods …

Hybrid Electro-Plasmonic Neural Stimulation With Visible-Light-Sensitive Gold Nanoparticles, Ratka Damnjanovic, Parveen Bazard, Robert D. Frisina, Venkat R. Bhethanabotla

Chemical and Biochemical Engineering Faculty Research & Creative Works

Biomedical prosthetics utilizing electrical stimulation have limited, effective spatial resolution due to spread of electrical currents to surrounding tissue, causing nonselective stimulation. So, precise spatial resolution is not possible for traditional neural prosthetic devices, such as cochlear implants. More recently, alternative methods utilize optical stimulation, mainly infrared, sometimes paired with nanotechnology for stimulating action potentials. Infrared stimulation has its own drawbacks, as it may cause collateral heating of surrounding tissue. In previous work, we employed a plasmonic method for stimulation of an electrically excitable neuroblastoma cell line, which had limited success. Here, we report the development of a hybrid electro-plasmonic …

Multihazard Hurricane Fragility Model For Wood Structure Homes Considering Hazard Parameters And Building Attributes Interaction, Carol C. Massarra, Carol J. Friedland, Brian D. Marx, J. Casey Dietrich

Faculty Publications

Predicting building damage as a function of hurricane hazards, building attributes, and the interaction between hazard and building attributes is a key to understanding how significant interaction reflects variation hazard intensity effect on damage based on building attribute levels. This paper develops multihazard hurricane fragility models for wood structure homes considering interaction between hazard and building attributes. Fragility models are developed for ordered categorical damage states (DS) and binary collapse/no collapse. Exterior physical damage and building attributes from rapid assessment in coastal Mississippi following Hurricane Katrina (2005), high-resolution numerical hindcast hazard intensities from the Simulating WAves Nearshore and ADvanced CIRCulation …

Bio-Oils From Vacuum Ablative Pyrolysis Of Torrefied Tobacco Residues, Nattawut Khuenkaeo, Blake Macqueen, Thossaporn Onsree, Sangu Daiya, Nakorn Tippayawong, Jochen A. Lauterbach

Faculty Publications

Fast pyrolysis, in combination with torrefaction pretreatment, was used to convert tobacco residues to value-added bio-fuels and chemicals. Tobacco plant residues were torrefied at 220, 260, and 300 °C, before being pyrolyzed at 450, 500, 550, and 600 °C in a rotating blade ablative reactor under vacuum conditions to test the effects on product yields. With torrefaction, tobacco residues thermally decomposed 20-25% w/w at low temperatures. Torrefaction and pyrolysis temperatures were found to markedly affect pyrolytic product yields of bio-chars and bio-oils, while having no effect on gas-phase products. Bio-oil yields exhibited a direct relation with pyrolysis temperature and an …

Information Technology News, Georgia Southern University

Information Technology: News & Publications (2012-2023)

• Georgia Southern Center for Applied Cyber Education to take part in cyber exercise

Epoxy-Functional Thermoplastic Copolymers And Their Incorporation Into Thermosetting Resins, Kayla Rose Sweet

Theses and Dissertations

While polymers have secured a place in the consumer, industrial, and military markets over the last seventy years, the next generation of polymers must become more renewable, more adaptive, and higher performing to bridge industrial needs and environmental gaps. To this end, unique network configurations of copolymers and interpenetrating polymer networks (IPNs) have been employed to combine features of two or more polymers into a single material that surpasses the sum of its parts. The customization of polymer networks can be made possible via dual-functional monomers, molecules characterized by two different reactive substituents that allow for versatile methods of polymerization. …

Bio-Oils From Vacuum Ablative Pyrolysis Of Torrefied Tobacco Residues, Nattawut Khuenkaeo, Blake Macqueen, Thossaporn Onsree, Sangu Daiya, Nakorn Tippayawong, Jochen A. Lauterbach

Faculty Publications

Fast pyrolysis, in combination with torrefaction pretreatment, was used to convert tobacco residues to value-added bio-fuels and chemicals. Tobacco plant residues were torrefied at 220, 260, and 300 °C, before being pyrolyzed at 450, 500, 550, and 600 °C in a rotating blade ablative reactor under vacuum conditions to test the effects on product yields. With torrefaction, tobacco residues thermally decomposed 20-25% w/w at low temperatures. Torrefaction and pyrolysis temperatures were found to markedly affect pyrolytic product yields of bio-chars and bio-oils, while having no effect on gas-phase products. Bio-oil yields exhibited a direct relation with pyrolysis temperature and an …

Data Is Personal: We Should Treat It As Such, Kaleb Dunn

Student Papers in Public Policy

The rise of the internet as a fact of daily life is the defining element of the modern age. Widespread use of the internet has fundamentally altered entire industries, and much of American life has migrated online. Dating is augmented by online dating; shopping by online shopping; television by internet streaming.

The digitization of American life has brought with it considerable benefits, including great convenience and innumerable efficiencies, but it has not come without a cost. Although there are many business models used by internet companies, many of the now-largest companies in the world have converged on one entity upon …

The Glycocalyx And Its Role In Vascular Physiology And Vascular Related Diseases, Sheldon Weinbaum, Limary M. Cancel, Bingmei M. Fu, John M. Tarbell

Publications and Research

Purpose—In 2007 the two senior authors wrote a review on the structure and function of the endothelial glycocalyx layer (Weinbaum in Annu Rev Biomed Eng 9:121–167, 2007). Since then there has been an explosion of interest in this hydrated gel-like structure that coats the luminal surface of endothelial cells that line our vasculature due to its important functions in (A) basic vascular physiology and (B) vascular related diseases. This review will highlight the major advances that have occurred since our 2007 paper.

Methods—A literature search mainly focusing on the role of the glycocalyx in the two major areas described above …

Application Of Modified River Health Index For Sungai Penchala, Sathis Venkitasamy

Student Works (2020-2029)

The aim of this study is to have a tool of management of an urban river. A simple tool in terms of index aimed to be developed to manage urban river to meet its intended usage. River Health Index (RHI) developed by combining both physico-chemical parameters and biological measures through scores and weightages. Sungai Penchala is the small urban river chosen for this study. Water quality study, which include physico-chemical parameters, benthic macroinvertebrates and surrounding land use activities have been carried out since May 2016 to September 2016. Ten sampling points have been selected to represent the condition of the …