Engineering Commons^™

Influence Of A Backward-Facing Step On Swept-Wing Boundary-Layer Transition, Jenna L. Eppink, Richard W. Wlezien, Rudolph A. King, Meelan Choudhari

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Experimental measurements were performed on a swept flat-plate model with an airfoil leading edge and imposed chordwise pressure gradient to determine the effects of a backward-facing step on transition in a low-speed stationary crossflow-dominated boundary layer. Detailed hot-wire measurements were performed for three step heights ranging from 36 to 49% of the boundary-layer thickness at the step and corresponding to subcritical, nearly critical, and critical cases. In general, the step had a small, localized effect on the growth of the stationary crossflow vortex, whereas the unsteady disturbance amplitudes increased with increasing step height. Intermittent spikes in instantaneous velocity began to …

Corrigendum To ‘Zinc Oxide As An Active N-Layer And Antireflection Coating For Silicon Based Heterojunction Solar Cell’ [Sol. Energy Mater. Sol. Cells 139 (2015) 95–100](S0927024815001324)(10.1016/J.Solmat.2015.03.017), Babar Hussain, Abasifreke Ebong, Ian Ferguson

Electrical and Computer Engineering Faculty Research & Creative Works

The authors regret that permanent email address of the corresponding author is "[email protected]". The authors would like to apologize for any inconvenience caused.

Improving The Delivered Specific Impulse Of Composite Rocket Propellant Through Alteration Of Chemical Composition: Methodology And Parameters For Characterization Of Propellant And Validation Of Simulation Software Common To The Amateur Rocketry Community, Isaac O'Brien, Austin Ryan

Williams Honors College, Honors Research Projects

In this study, two solid composite rocket propellants were designed utilizing ProPEP, a rocket propellant formulation software common in the amateur and hobby rocketry communities. The two propellants were designed to optimize specific impulse relative to a literature propellant designed by 1020 Research Labs. The literature propellant was also tested in order to validate the design of experiment as well as the mixing and testing procedures. All three propellants, which includes the literature propellant RCS-P, and the two novel propellants AKR-P1 and AKR-P2 were characterized with static tests. The results of the static tests provide data on propellant performance and …

Battery Powered Handheld Drain Cleaner, Sarah Michaud, Kaylin Cozzens, Emily Jo Spinelli

Williams Honors College, Honors Research Projects

By pairing up with Ridge Tool Company in Elyria, Ohio, we developed a competitive redesign based on their K-45 Sink Machine. Some goals set forth at the beginning were to take the machine from a corded system with a brushed motor to a battery powered one with a brushless motor, and to address some consumer concerns in regards to weight support and ease-of-use. Our final objective was to assemble a functional prototype that could be submitted to Ridge Tool Company for review. This redesign should help this machine remain competitive in the field, and give us the chance to present …

Stabilization Of Dredged Materials In Ohio: An Investigation Of Mechanical, Chemical And Biological Dewatering Techniques, Erika Howard

Williams Honors College, Honors Research Projects

Each year, materials are excavated from oceans and lakes in order to keep the waterways open so that ships can safely pass through. These excavated, or dredged, materials are then discarded, usually being returned to the body of water from which they were removed. Beginning in 2020, the Ohio Environmental Protection Agency (OEPA) will no longer allow this to occur. Therefore, the purpose of this project is to investigate beneficial uses for dredged materials in Lake Erie, and to address the best management practices for dewatering these materials, as set forth in the Lake Erie Protection and Restoration Plan created …

Space Dynamics Laboratory Payload Challenge: Autonomous Water Sampling Uav, Thomas Wheeler, Zachary Williams, Joseph Stack

Williams Honors College, Honors Research Projects

The following report has been completed over the course of the Fall 2018 and Spring 2019 semesters at The University of Akron by Joseph P. Stack (Aerospace Systems Engineering), Thomas J. Wheeler (Mechanical Engineering) and Zachary M. Williams (Mechanical Engineering). The purpose of this project was to create a payload system for the Akronauts Rocket Design Team to use at the Intercollegiate Rocket Engineering Competition (IREC) Spaceport America Cup. The Competition as a challenge that is sponsored by Space Dynamics Laboratory specifically regarding payload systems. The challenge in very open-ended and allows student to identify their own scientific experiment and …

Effects Of Micro-Features On Cell Detachment From Poly(N-Isopropylacrylamide) Coated Polydimethylsiloxane Membranes, Luke Webel

Williams Honors College, Honors Research Projects

The tested hypothesis was that features on polydimethylsiloxane (PDMS) surfaces coated with a poly(N-isopropylacrylamide)/aminopropyltriethoxysilane or pNIPAAM/APTES thin film would accelerate cell detachment than the film coated on a unfeatured surface. This project tested samples with features generated by molds, wrinkling, and sandpaper roughened substrates. Surface feature generation methods were limited to mechanical means, and characterized by microscopy and strain rates. 50/50 mixtures of 1.5 wt.% pNIPAAM/ APTES were used to coat thin films (30-40 nm) on PDMS membranes by spin-coating, and the coated membranes were thermally annealed to chemically graft pNIPAAm/APTES on the membrane and their thermo-responsive property was assessed …

Prototype Landing Gear Conceptual And Embodiment Design, Derek Carr

Williams Honors College, Honors Research Projects

Collin’s Aerospace Mechanical systems engineering was tasked with designing a set of landing gear for an undisclosed project. The landing gear is required to comply with customer specifications, coordinate systems, and overall landing gear performance. The purpose of this project is to document the conceptual and embodiment design process for an articulated main landing gear system. Unfortunately, due to high expenses and high lead times required for 300M stainless steel components, no full size prototype can be produced within the timeframe of this report. Instead, this document should be viewed as a process mapping guide for initial landing gear design …

Exoskeleton Leg Brace, Aaron Indermuhle, Magomed Kasumov, Cevat Bagcioglu, Lucas Battaglia

Williams Honors College, Honors Research Projects

This report details the design process of a lower limb exoskeleton leg brace for elderly people with walking disabilities or others with disabilities that limit mobility. While there are other similar products on the market, the general design can be improved and these improvements have been implemented into the design presented within. Among these improvements are progress in efficiency, weight, user comfort, and cost. The results of the study are the design of a novel leg brace that improves on existing designs in each of these areas.

Our design solution incorporates the use of a single leg brace with no …

Project "Auxilia" - Jaiden's Prosthetic Arm, Christopher Halley, Lindsay Jaros, Autumn Young

Williams Honors College, Honors Research Projects

The main objective of this project was to create a prosthetic arm for a 15 year old boy named Jaiden Foden. Jaiden was born with only one fully developed limb as a result of a genetic disorder, Hanhart Syndrome II. His right arm becomes a residual limb below the elbow, but has two fingers which act in a “claw-like” movement. Jaiden’s left arm becomes a residual limb above the elbow, and his left leg becomes a residual limb above the knee. The goal of the arm was to increase Jaiden’s overall independence and to help in completing daily tasks, such …

Reactive Archey Target Design Team "Mimic", Brandon Croyle, Jacob Boss, David Rodgers, Austin Wivell

Williams Honors College, Honors Research Projects

This design project will aim to provide archery hunters with a platform to simulate shooting at string jumping deer. String jumping refers to a spooked deer hearing the snap of a bow string and instintivly ducking up to ten inches. This often results in wounded or missed deer. We will design and build a control system that uses the sound of a bow string as a trigger to operate a mechanical target system. A sound sensor will mimic a deer’s hearing in close range hunting and then send a signal to the mechanical system to replicate the dropping motion of …

Increasing Mechanical Properties Of A Double Network Hydrogel From Polyacrylamide And Agar With Methylenebisacrylamide As A Photocrosslinker, Madelyn Jeske

Williams Honors College, Honors Research Projects

Double Network hydrogels are three dimensional networks of a soft, mechanically tough material that have been used for drug delivery, agriculture, adhesives, and other widely applicable uses. Using the one-pot method, a single hydrogel can be produced in 3 hours as opposed to the once demonstrated three days. It has been found that with a first, physically cross linked network and a second, chemically cross linked, hybrid double network hydrogels exhibit high mechanical properties and are freeshapeable. Agar is a thermoreversible organic molecule with a triple helix structure that provides an excellent first network that organizes into aggregate bundles once …

Anti-Roll Bar For Sae Baja Vehicle, Jennifer Bulgrin, Zachary A. Gnabah, Scott P. Toth

Williams Honors College, Honors Research Projects

This report explores the need to improve the Zips Baja vehicle handling performance. This will be achieved by designing an anti-roll bar system for the rear suspension of the Zips Baja vehicle to decrease the turning radius of the vehicle. The project develops specific goals to achieve increased performance, goes through the engineering design cycle to create a prototype, evaluate its effectiveness, optimize the design through several iterations, and design a final solution. After sub-functions have been determined, conceptual ideas for completing all sub-functions were evaluated and a conceptual design was selected to proceed into the embodiment design phase. Once …

Benefits Of Aluminum: Comparing The Common Materials In The Bar Grating Industry, Joanthan Geiser

Williams Honors College, Honors Research Projects

The main aim of this project is to study the wholistic behavior of the 6xxx series of aluminum for use in the bar grating industry for a waste water treatment environment. This project will study the comparison of certain aluminum 6xxx series alloys to steel, stainless steel, and glass fiber-reinforced plastic. While comparing these materials, it will look at the mechanical properties such as modulus of elasticity, yield strength, and ultimate tensile strength. In addition, the available corrosion test of the 6xxx series aluminum alloys will be examined to find a generalization of the corrosion behavior for this series. A …

Center Lift Trailer Support Structure, Carson Corle, Anthony M. Hayes, Bryan A. Truax

Williams Honors College, Honors Research Projects

Center lift pontoon trailers have a high center of gravity, therefore have the potential for the pontoon and trailer to tip while cornering. There is need for a component to stabilize the pontoon on the trailer while towing. Different concepts of a support system were sketched to determine the best option. The characteristics that were deemed important for the support system were narrowed down to determine the best concept and the connections of the best design were sketched in greater detail. The forces that the support system would have to withstand to stabilize the pontoon on the trailer were calculated. …

Fluidized Bed Classroom Demonstration Unit, Theresa Chapa

Williams Honors College, Honors Research Projects

Fluid and Thermal Operations is a 4th year chemical engineering course at the University of Akron designed to introduce undergraduate students to the engineering and mathematical concepts behind the operation of a fluidized bed. The purpose of this honors project is to design and manufacture an inexpensive and portable unit that can be used in the classroom to visually demonstrate three functions of a fluidized bed to students. The fluidized bed is manufactured from items that can be purchased from a department or hardware store, is capable of being transported by a single person to and from a classroom and …

Automatic Range Finding Bow Sight, Garrett Gill, Dillon Denny, Cory Verba

Williams Honors College, Honors Research Projects

With the growing popularity of archery, a system designed to help an archer achieve the best shot possible becomes necessary. The Automatic Range Finding Bow Sight is a system that consists of a single pin sight controlled by a servo motor. The servo motor controls the sight pin by rotating a drive wheel that will move the pin up or down. The sight pin movement is based on a reading obtained by a built-in rangefinder and speed data input by the user. This data will then be compared to programmed lookup tables in order to find the appropriate pin position. …

Investigating Alternative Measures Of Functional Recovery In Rat Sciatic Nerve Injury, Mariah L. Costa, Rebecca K. Willits

Williams Honors College, Honors Research Projects

There is a pressing need for advancements in peripheral nerve repair techniques and functional recovery evaluation methods. The rat sciatic nerve injury model is a well examined model for peripheral nerve repair. One measure of functional recovery after nerve damage, the sciatic functional index (SFI), fails in the presence of self-mutilation, toe contracture, and other abnormalities in gait. In this IACUC approved study, the sciatic nerve was severed in four experimental groups (n=5). The nerves were repaired with Arginylglycylaspartic acid-poly(ε-caprolactone) (RGD-PCL) peptide functionalized nanofibers, non-functionalized PCL control nanofibers, an isograft, and a negative control empty conduit. Video walking track analysis …

Optimization Of Conditions For Production Of Mechanically Strong Suckerin Protein Hydrogels, Autumn Furniss

Williams Honors College, Honors Research Projects

Hydrogels are polymer networks with a large water content. Uses include biomedical applications like drug delivery, wound dressing, and more. Current natural hydrogels lack mechanical robustness. Squid ringed teeth (completely protein) have a modulus comparable to thermoplastics; adding this to hydrogels could improve modulus while maintaining biocompatibility.

Three experiments were performed: Hofmeister solubility study, SRT powder additive, and SRT aqueous solution. The first showed that LiCl solution without acetic acid dissolved the most SRT; overall LiCl dissolved more than all others. SRT as a powder additive increased the modulus of the hydrogels, however the error in the measurements make it …

The Wrist Brace Project, Nathan Nicholas

Williams Honors College, Honors Research Projects

This paper outlines the engineering design process of creating a specialized wrist brace for a local child. This project was completed by a team of senior Biomedical Engineering students.

Fabrication And Characterization Of Nanofiber Nylon-6-Mwcnt As An Electrochemical Sensor For Sodium Ions Concentration Detection In Sweat, Kelsey Mills

Williams Honors College, Honors Research Projects

Fabrication and characterization nylon-6-MWCNT nanofiber as an electrochemical sensor to detect sodium ion concentrations specifically in sweat. Using contact angle to determine surface morphology and chronoamperometry testing to identify ideal sensor conditions, tests optimized parameters like weight percent of nylon or other polymers, carbon nanotube (CNT) isomer, and solution concentration to determine reproducibility of functional sensors. Utilizing the electric qualities of carbon nanotubes partnered with the sodium ion selectivity of calixarene treatment and polymers unique properties like flexibility and scalability create open an arena for optimizing sodium ion sensors for further development for functional prototypes. Morphology tests showed that the …

Synthesis Of Drug Encapsulated Chitosan-Heparin Based Nanoparticles And Release Study, Trent Richwine

Williams Honors College, Honors Research Projects

The main objective of this honor’s project is to encapsulate drugs with different molecular weights inside of chitosan-heparin based nanoparticles (Cs-Hep NPs). Three different drugs with low (NNC), medium (IFN-γ), and large (BSA) molecular weights were chosen in order to compare all types of drugs and how they react with the nanoparticles. Analysis of particle size, zeta potential, and a release study was performed. The release took place over a 168-hour time period and liquid samples were taken throughout. The hypothesis was that the molecular weight of the drug will correlate to the physical properties of the nanoparticles. The results …

Simulation Of Lubricant For Design Of Magnetic Recording Systems Under Laser Heating, Ryan Hetzel, Shao Wang Dr., Jonathon Lawry, Ahmed Alsafwani

Williams Honors College, Honors Research Projects

Heat assisted magnetic recording is an advanced technology which can enable storage density increase in next generation hard disk drive. These drives are implemental in server (cloud) storage and the storage of large projects such as the Event Horizon Telescope which recently captured images of a black hole. The data is written on the magnetic surface by means of laser heating. The coercivity of magnetic medium is reduced by heating surface and within heating period data is written on disk. During the heating process, lubricant present on the disk might evaporate because of high temperature of laser and can accumulate …

Artificial Intelligence In Wet Weather Infrastructure, Matt Hammerstein

Williams Honors College, Honors Research Projects

Effective management of runoff from rain and snowmelt is critical as increased water flows can negatively affect efficiency and reliability at treatment facilities, as well as potentially damage property or the natural environment. Implementation of artificial intelligence for real-time decision making and support in wet weather infrastructure is a recent technological development; as such, a problem has emerged: experience and knowledge of best practices for successful implementation is limited. Artificial intelligence is being employed to inform operational decisions that are intended to improve the efficiency and reliability of physical wet weather infrastructure. The goal of municipalities and utilities in utilizing …

Incorporation Of Contaminated Sediment Into Environmentally Safe Concrete, Andrew Needs

Williams Honors College, Honors Research Projects

The research performed through this project provided some interesting results on how the different properties of the contaminated sediment can impact the strength of the new concrete.

Average three, seven, and fourteen-day strengths increased when comparing to the baseline mix developed for the experiment. Increases in strengths were notices in the ten and twenty-five percent soil replacement mixes. The largest increase was approximately thirty-three percent greater than the baseline average.

The results from the forty percent replacement test showed a significant decrease in strengths when comparing against the baseline mix. A loss of about thirty percent was observed between the …

Development Of Cardanol-Based Epoxy Coating, Nicholas Pottschmidt

Williams Honors College, Honors Research Projects

The purpose of this project was to determine the suitability of cardanol glycidyl ether (CGE) as a substitute for trimethylolpropane triglycidyl ether (TMPGE) as the reactive diluent in epoxy coatings. CGE may be a naturally-derived alternative to TMPGE, which is a commonly-used petroleum-derived reactive diluent. Epoxy coatings were formulated with CGE replacing increasing amounts of TMPGE in the formulation. Corrosion protection provided by the coatings was evaluated with electrochemical impedance spectroscopy (EIS). Mechanical properties of the coatings (hardness, flexibility, adhesion, and impact resistance) were evaluated with applicable ASTM standards.

EIS results revealed the coating formulated with only CGE had superior …

Design And Mechanical Characterization Of 3d Printed Gradient Porosity Poly(Propylene Fumarate) Scaffolds, Andrea Felicelli

Williams Honors College, Honors Research Projects

Worldwide incidence of bone disorders and conditions, an already prevalent problem, is expected to double by 2020 from the rate in 2013 due to factors such as higher life expectancies and lower levels of physical activity. Every year in the United States, over half a million patients receive bone defect repairs, with costs greater than $2.5 billion. Current repairs are typically done with bone grafts, which are often costly and can result in added complications in the donor surgical site. Tissue engineering, a growing field that seeks to assist and enhance tissue defect repairs through the use of synthetic materials, …

Fluid Power Vehicle Competition, Madison Graham, Wayne Ritchie, Emily Dicks, Ariana Cupello

Williams Honors College, Honors Research Projects

Our senior design project for the Honors College and the Department of Mechanical Engineering was to design a fluid powered vehicle. Our design was tested in an official capacity against other universities’ vehicles at the Fluid Powered Vehicle Challenge hosted and funded by the National Fluid Power Association (NFPA) and its industry partners. This competition had six different evaluations for our vehicle design; three race events, midway presentation, final presentation, and safety inspection. The three different race events were the sprint race, the efficiency race, and the endurance race. The sprint race was a 475 feet speed test, the efficiency …

Carbon Fiber Racing Wheel, Megan Sanok, Melissa Furdak, Sydney Schipani

Williams Honors College, Honors Research Projects

Industry today thrives off of competition; everybody wants their product to be the best. Across almost every field of manufacturing and design, there is a pattern of factors that companies strive for when producing their specialized products. The most effective companies can create a commodity that is relatively inexpensive, easy to manufacture, and has the ability to meet high standards. As engineers, it is ingrained in us that there is always room for improvement, and that we have been given the tools to make it happen.

When evaluating what needed to be improved in our daily lives, the SAE Zips …

Smart Parking Deck, Ryne Turner, Matthew Mcdade, Julie Aichinger, Laveréna Wienclaw

Williams Honors College, Honors Research Projects

The Smart Parking Deck employs elementary circuit design elements and mobile application development. Each device module uses laser proximity sensors to check the availability of an individual parking space and a Zigbee unit to communicate with the adjacent device module. The modules are connected to a network hub that manages all of the incoming and outgoing parking data. This data is displayed on the mobile application. The system is easily manageable and energy efficient, significantly decreasing the costs associated with other smart parking systems on the market. This system is aimed at decreasing commute time for students by allowing them …