Engineering Commons^™

Evaluation Of Naturally Occurring And Anthropogenic Contamination In Missouri Streams, Christina Jane Sehrt

Masters Theses

"The goal of this study is to observe the values and variability of water quality parameters and benthic macroinvertebrates in watersheds with very little anthropogenic impact and to compare these values with those acquired in watersheds with more anthropogenic impact. The following five HUC 12-digit watersheds had very little anthropogenic impact and were considered "pristine": Rogers Creek, Mill Creek, Middle West Fork-Black River, Bee Fork, and Ottery Creek. Five largely urban sub-basins were also considered; these basins are: Grand Glaize Creek, Glaize Creek, Sugar Creek, Hominy Creek, and Grindstone Creek. For each watershed, both water quality parameters and benthic macroinvertebrates …

Emi Design Of Flyover Qsfp (Fqsfp) Connector For 56+ Gbps Applications, System Level Modelling Of The Z-Directed Component (Zdc), Pranay Kumar Vuppunutala

Masters Theses

"This thesis comprises of two parts. Firstly, the Flyover Quad Small Form Pluggable (FQSFP) approach for 56+ Gbps applications is introduced to overcome the limitations from a large loss on typical QSFP ports with surface mount to Printed Circuit Board (PCB) traces. By replacing the PCB traces to the twinax cables, it is possible to achieve around 7 dB lower insertion loss at 40 GHz for the 12-inch path from the switch IC to connector than that of PCB trace with a low loss substrate. Also, to investigate electromagnetic interference (EMI) aspect of FQSFP approach, a simulation model of FQSFP …

Program Management For Concurrent University Satellite Programs, Including Propellant Feed System Design Elements, Shannah Withrow-Maser

Masters Theses

"Propulsion options for CubeSats are limited but are necessary for the CubeSat industry to continue future growth. Challenges to CubeSat propulsion include volume/mass constraints, availability of sufficiently small and certified hardware, secondary payload status, and power requirements. A multi-mode (chemical and electric) thruster was developed by at the Missouri University of Science and Technology to enable CubeSat propulsion missions. Two satellite buses, a 3U and 6U, are under development to demonstrate the multi-mode thruster's capabilities. Two key challenges related to these missions are the development of the feed system to support the thruster and management of the two bus programs' …

Computational Fluid Dynamics Modeling Of Proppant Static Settling Velocity In High Viscosity Friction Reducers, Chen Yuan

Masters Theses

"In the current petroleum fracturing industry, it is necessary to understand the downhole migration and settling velocity of the proppant. If we can master this information well, it will be a great help to obtain effective propped fracture conductivity. In order to study the transport of proppants in the well, we used laboratory experiments and computer numerical simulations to compare the results to get a meaningful conclusion. We spent a lot of time building models on a powerful computer and comparing the experimental conclusions. We finally decided to use computational fluid dynamics (CFD) as the simulation platform, discrete phase method …

Modeling Overpressure Development During Shale Rock Compaction Coupling Poroelasticity And Permeability Evolution Above 3km Depth, Wenyu Zhao

Masters Theses

"The evolution of pore pressure including overpressure during sedimentation is an important process to consider when analyzing whether high pore pressure causes rock failure. High pore pressure is caused by under-compaction due to the rapid burial of low-permeability sediments, and as a result, porosity decreases less rapidly with depth than in normally compacted sediments where porosity decreases exponentially with depth. While under-compaction related pore pressure magnitudes have been determined empirically, in most numerical modeling approaches, the pore pressure is either applied as a static magnitude or coupled to a fluid flow simulator. This study simulates the pore pressure evolution during …

Gel Composition And Brine Concentration Effect On Hydrogel Dehydration Subjected To Uniaxial Compression, Xinrui Zhao

Masters Theses

"Gel treatment is a process that injects the gel into a reservoir to control the conformance and improve the sweep efficiency of injection fluids. At a certain pressure gradient, the gel dehydrates in a reservoir due to mechanical forces. This work evaluates the effects of the gel composition and brine concentration on gel dehydration under uniaxial compression. A sodium acrylate-co-acrylamide based gel cross-linked with N, N'-Methylenebisacrylamide (MBAA) was used for the study. The compression test is performed with a rheometer with a plate-plate geometry. The gel dehydration under pressure was measured to see how gel dehydration would be impacted by …

Coupling Path Visualization Based On Reciprocity Theorem, Yang Zhong

Masters Theses

"A new method to visualize coupling path is proposed to help solve EMI problems. Based on the reciprocity theorem and the concept of reaction, coupling coefficient (CC) is defined to characterize coupling power density. For two-port networks, surface integral of CC can represent coupled voltage on the open-circuited port or coupled power on the loaded port. For dipole-moment based systems, surface integral of CC can represent coupled field components. The calculated CC should be a complex scalar at each point. By properly adjusting the excitation phases, the imaginary part of surface integral of CC will be zero and thus can …

Breaker Evaluation And Formation Damage Remediation Of Re-Crosslinkable Preformed Particle Gel (Rppg), Enze Zhou

Masters Theses

"Re-crosslinkable preformed particle gel (RPPG) is a newly developed preformed particle gel for improving sweep efficiency and oil recovery by blocking or reducing the conductivity of fractures and fracture-like channels or conduits. However, RPPG has the potential to plug the facilities or damage the formation if a treatment is not properly conducted.

This work presents the performance of selected oxidizing breakers on the degradation of RPPG. The influence of a few factors on the degradation process was investigated, including breaker type, breaker concentration, temperature, gel concentration, gel aging time, and gel size. Results indicate that breaker type, concentration, and temperature …

Using The Ert Method To Differentiate Resistivity Anomalies Attributed To Natural And Man-Made Activities, Ibrahim Faisal Alshareef

Masters Theses

"Karst terrain is considered to be a very complex topography compared with most other geological environments. Many features can be observed such as sinkholes, air-filled cavities, losing streams, and solution widened joints. These karst features can cause subsidence and damage infrastructure such as buildings and roads thus causing economic hardship and disruption of life. The typical geological and hydrological studies are not enough to understand the karst processes.

For this reason, two geophysical methods were involved in investigating the subsurface in the study area. In this research, the electrical resistivity tomography (ERT) and multichannel analysis of surface wave (MASW) data …

Development Of Test Methods For Characterizing Extrudability Of Cement-Based Materials For Use In 3d Printing, Jonathan Thomas Kuchem

Masters Theses

"3D printing is the process of creating three-dimensional objects using an automated additive manufacturing process. The 3D printing process has been used with materials such as metals and polymers, but application with cement based materials for the construction industry has yet to be developed. In this research, two main problems were investigated for printing cement based composite materials: extrudability and tensile reinforcement. Fiber-reinforced concrete (FRC) was studied as an internal reinforcing system to increase tensile/flexural strength. First, FRC was studied to investigate mechanical properties and use of fibers from waste tires as an environmentally friendly option. A reference mixture with …

Less Is More: Beating The Market With Recurrent Reinforcement Learning, Louis Kurt Bernhard Steinmeister

Masters Theses

"Multiple recurrent reinforcement learners were implemented to make trading decisions based on real and freely available macro-economic data. The learning algorithm and different reinforcement functions (the Differential Sharpe Ratio, Differential Downside Deviation Ratio and Returns) were revised and the performances were compared while transaction costs were taken into account. (This is important for practical implementations even though many publications ignore this consideration.) It was assumed that the traders make long-short decisions in the S&P500 with complementary 3-month treasury bill investments. Leveraged positions in the S&P500 were disallowed. Notably, the Differential Sharpe Ratio and the Differential Downside Deviation Ratio are risk …

Propagation Of Uncertainty Through Coning, Sculling, And Scrolling Corrections For Inertial Navigation, James Daniel Alan Brouk

Masters Theses

"This thesis investigates the propagation of estimation errors through generalized coning, sculling, and scrolling algorithms used in modern day inertial navigation systems, in order to accurately quantify the uncertainty in the estimation of position, velocity, and attitude. The corrections for coning, sculling, and scrolling algorithms have an often unaccounted for effect on documented and empirically derived error statistics for measurements used to predict the uncertainty in a vehicle's position, velocity, and attitude estimates. Through the development of an error analysis for these generalized algorithms, mappings of the measurement and estimation errors through the correction termare generated. Using the developed mappings, …

Performance Investigation Of Surface Modified Ceramic Microfiltration Membranes And The Effects Of Ionic Strength, Choji Bitrus Daches

Masters Theses

"The performance of ceramic membranes surface coated with cysteic acid to improve efficiency and reduce fouling rate was studied under two transmembrane pressure (TMP) and constant crossflow velocity (CFV). The filtration process was done in crossflow mode to allow for extended operation of the membranes. the performance of the membranes were determined in terms of the measured fluxes and on content rejection. Cleaning-in-place (CIP) was done on the membranes to ensure flux recovery after each run. The results showed significant improvement on the performance of the membranes with respect to high permeate fluxes and high oil content rejection (> 99.5%). …

Temporal Changes Of Nutrients Within The Lower Grand River Watershed And Selected Sites, Weston Scott Duley

Masters Theses

"This report presents the results of a study carried out in collaboration with the U.S. Geological Survey (USGS) and the Missouri Department of Natural Resources (MDNR) to estimate total nitrogen (TN) and total phosphorus (TP) at five USGS monitoring sites within Lower Grand River Watershed (LGRW) and two monitoring sites on the Missouri River. The objective of this study was to quantify temporal changes in TN and TP concentrations and compare those to best management practices (BMPs).

In this study, the approach to the analysis of long-term surface water-quality data by using Weighted Regressions on Time, Discharge and Seasons models …

Geophysical Imaging Beneath Lake Chesterfield, Missouri, James Daniell Hayes

Masters Theses

"Lake Chesterfield in Wildwood, Missouri, has been leaking since construction of the earth-fill dam was completed in 1986, despite numerous mitigation efforts. The mitigation efforts, including the injection of grouting and the emplacement of clay liners, has not solve the leakage problem.

In the current study, geophysical (subsurface imaging) data was acquired across the drained and dry lake bed and along the base of the earth-fill dam to 1) map variable depth to top of bedrock, 2) determine the variable quality of the bedrock to depths on the order of 80 ft., 3) identify any significant karst features beneath the …

Characterization Of The Surface Condition In Aa6061 Resulting From Deep Rolling As A Function Of Common Industrial Parameters, Andrew Kenneth Layer

Masters Theses

"Roller burnishing is widely used in industry to improve the surface finish and fatigue life of components. As weight reduction continues to grow in the automotive and transportation industries, deep rolling can help maintain product performance by mitigating the increase in component stresses resulting from lower weight systems. Deep rolling parameters such as tool, applied angle, feed rate, spindle speeds, and relative tool direction all affect cycle time, product performance, and appearance. The effects of common industrial parameters on the resultant surface roughness and residual stress profiles were studied in this investigation. The samples were manufactured on a CNC lathe …

Practical Methods For Source Separation In Emc Measurements, Yuanzhuo Liu

Masters Theses

"Electromagnetic emission is critical in the electronic industry with the rapid growth of the development of the electronic device. To identify the emission from the multipule sources, two methods are proposed in the near field scan and total radiated power measurement respectively.

The first method can be applied in the measurement of the field generated by multiple non-correlated sources. The contribution of each source is determined using a blind source separation (BSS) technique. The measurements are performed using one scanning probe and stationary reference probes, avoiding the need to measure the spatial correlations of the random field. The resolving result …

The Effect Of Cell Size And Surface Roughness On The Compressive Properties Of Abs Lattice Structures Fabricated By Fused Deposition Modeling, Leah Hope Mason

Masters Theses

"Postprocessing is an important step in many manufacturing methods, but it is especially important for additive manufacturing. Researchers looking to improve the surface roughness of acrylonitrile butadiene styrene (ABS) parts fabricated by fused deposition modeling (FDM) have determined that acetone smoothing not only achieves improved surface roughness but increases compressive strength as well. This could be very beneficial to lattice structures, which are known for already having an excellent strength to weight ratio. If the compressive strength of ABS lattice structures could be improved even further using acetone smoothing, it could expand the applications for plastic lattice structures and improve …

Small Satellite Earth-To-Moon Direct Transfer Trajectories Using The Cr3bp, Garrett Levi Mcmillan

Masters Theses

"The CubeSat/small satellite field is one of the fastest growing means of space exploration, with applications continuing to expand for component development, communication, and scientific research. This thesis study focuses on establishing suitable small satellite Earth-to-Moon direct-transfer trajectories, providing a baseline understanding of their propulsive demands, determining currently available off-the-shelf propulsive technology capable of meeting these demands, as well as demonstrating the effectiveness of the Circular Restricted Three Body Problem (CR3BP) for preliminary mission design. Using the CR3BP and derived requirements from NASA's Cube Quest Challenge, five different trajectory scenarios were analyzed for their propulsive requirements. Results indicate that the …

Near-Field Scanning Based Shielding Effectiveness Extraction For Board Level Shielding Cans, Harsh Shrivastav

Masters Theses

"The conventional definition of shielding effectiveness is well suited for calculating electromagnetic shielding in the far-field. However, in the near field, shielding effectiveness calculation is not so straight forward. In radio frequency interference problems, most of the field coupling occurs in near field. Having a well-defined method to calculate near-field shielding effectiveness is important for estimating the suppression of radio frequency interference using the shield cans. In this research, a method to extract the shielding effectiveness of board level shielding cans using near field scanning is developed. Shielding effectiveness is defined by modelling the shielded noise source as equivalent dipole …

Changes In Fresh Properties Of Flowable Concrete Induced By Pumping And Composition Of The Lubrication Layer, Alexis Salinas

Masters Theses

"Pumping is an easy method to move concrete while keeping stability. It is worldwide accepted as one of the principal methods for concrete placement, as it accelerates construction. Typically, concrete acceptance in terms of fresh quantitative empirical properties (i.e. slump/slump flow and air content) are performed prior to the pumping process. However, empirical measurements have the drawback that they only measure 1 point. Rheology is better tool to evaluate the behavior of concrete. Pumping is a process that induces considerable shearing in the concrete that can impact its rheological properties. Therefore, the magnitude of these changes in fresh properties depends …

Developing A Model System Of Liquid Lubricants For Space Applications: Multiple Alkylated Cyclopentane In Alumina Enclosed Surface, Vidit Singh

Masters Theses

"Lubricants are substances used for reducing friction wear tear and energy losses between two moving bodies. For space applications, normal lubricants cannot be used as they cannot survive the harsh and demanding conditions of space. Multiple Alkylated Cyclopentanes (MACs) have been utilized as space lubricants in recent times with tremendous results. NASA uses the MACs for their missions in space, in particular 1,3,4- tri-(2-octyldodecyl) cyclopentane sold by Nye Lubricants under the name of Pennzane^TM.

In this research, an effort has been made to identify appropriate potential models for simulating Pennzane molecules and to develop MD simulation codes to …

Experimental Characterization Of Common-Mode Sources For Prediction Of System Level Common-Mode Current On Cable Harnesses, Sameer Sudha Arun Walunj

Masters Theses

"Common-mode current on cable harnesses is often the primary source of radiated emissions below several hundred megahertz. It is difficult, however, to estimate common-mode currents that will occur in a system from component level tests because the common-mode impedances are different in the system. Research presents two methods for using simple component level tests to estimate equivalent common-mode source voltages and source impedances responsible for generating common-mode current. Key to these methods is assuming the harness can be represented with two transmission lines, one terminated with a short and one with an open. Equivalent sources are predicted for those circuits …

Review And Data Analysis Of Low Salinity Water Effect Through Induced Fine Migration, Dawei Xu

Masters Theses

"Low salinity water flooding (LSWF) is well proved to be an effective EOR technology both in laboratory and field tests, however, the conditions for LSWF to work and EOR mechanism is still debatable. Up till now, many mechanisms have been proposed to explain the incremental oil recovery in sandstone by LSWF, for instance, fine migration, ionic exchange, wettability alteration and pH increase.

In this study, we only focus on low salinity water flooding effect through induced fine migration mechanism. The objective of this study is to conduct a comprehensive analysis using statistical analysis methods and explaining the mechanism of fine …

Projectile Impact Effects On A 50 Psi Plug Type Coal Mine Seal, Bruce Albert Von Niederhäusern

Masters Theses

"The current lack of projectile damage criteria for mine seals is assessed to determine if criteria should be developed. Impact experiments were performed on a full-scale 50 psi mine seal to determine failure modes, dynamic stress state, and assess risk to existing operational mine seals. Test projectiles were selected from common underground coal mine items propelled by means of a black powder projectile generator. Projectile velocities attained in testing ranged from approximately 100 to 650 ft/s (30 to 200 m/s). Dynamic strain was measured on the non-impact face to derive the state of stress and estimate failure criteria. Penetration models …

Multiphysics Prediction Model Of Microwave Curing For Thick Polymer Composites, Siva Dasari

Masters Theses

"Microwave curing technologies have many advantages over the traditional thermal curing methods for the manufacturing of fiber reinforced polymers, especially the processing speed and energy efficiency. Energy can be instantaneously transferred through applied electromagnetic fields and heat is generated based on dipolar rotational interactions. Microwave curing processes have been used for glass fiber composites but there are significant challenges associated with microwave curing of carbon fiber composites. Efficient heating may be difficult due to high dielectric loss associated with carbon fibers. Laminate quality will be highly dependent on the uniformity of the electromagnetic field in the material. In this work, …

Performance Evaluation Of Bmi Resin System For Thin-Ply Composites, Manoj Kumar Reddy Rangapuram

Masters Theses

"Composites materials are increasingly being used in aerospace applications over the past few years. The unique properties like high strength to weight ratio, thermal stability, fatigue and corrosion resistance set them apart from the conventional materials. Composite materials are well suited for the applications where weight is the primary concern in the design. Composites structures are vulnerable to mechanical as well as thermal loadings. Transverse micro-cracking and delamination are the most common type of failures in composite materials. The thickness of the ply being used play a key role dictating the properties of the resultant composite structure. As the ply …

Abrasion Resistant Concrete Mix Design For Cold Climates, Diane Mariah Murph

Masters Theses

“Studded tire usage in Alaska contributes to rutting damage on pavements resulting in high maintenance costs and safety issues. In this study, binary, ternary, and quaternary highly-abrasion resistant concrete mix designs using supplementary cementitious materials (SCMs) were developed. The properties of fresh concrete and mechanical, and durability properties of hardened concrete for these mix designs were then tested to determine an optimum highly-abrasion resistant concrete mixture which could be placed in cold climates to reduce rutting damage. SCMs used included silica fume, ground granulated blast furnace slag, and type F fly ash. Tests including workability, air content, drying shrinkage, compressive …

Methane Dry Reforming Reaction On Cr, V, In, And Ga Supported Sapo-34 Zeolite, Ehigiator Festus Ojo

Masters Theses

”The CO₂ reforming of methane is a significant research area in mitigating and transforming two greenhouse gases for the production of syngas. The reaction has been investigated for four different promoted catalysts to determine their reactant's conversion, product’s selectivity, and their respective syngas ratios.

The catalytic test was investigated under atmospheric conditions at 600⁰C for 6.5h with a WHSV of 4800 ml g^-1 h^-1. The conversion and selectivity of catalysts 9Al 1V-inc SAPO-34, 9Al 1Cr-inc SAPO-34, 9Al 1Ga-inc SAPO-34, and 9Al 1In-inc SAPO-34 were analyzed. The CH₄ conversion for the different catalysts are, 9Al 1Cr-inc …

Unmanned Aerial And Traversing Vehicle -- A Mobile Platform For Bridge Inspections, Clayton A. Fritsche

Masters Theses

“Unmanned aerial vehicles (UAVs), also known as drones, have been rapidly growing in popularity since their creation. This study aimed to create a robotic platform used to assist in the inspection process of the nation’s aging and deteriorating bridges. To this end, a multimodal inspection robot that utilized both flying and driving technologies, was designed, analyzed, and tested for aerial, traversing, and their transitional operability. The design, herein referred to as the “BridgeBot”, was evaluated both computationally and experimentally. A finite element model of the BridgeBot was established and analyzed under static loading scenarios to help determine stress distributions and …