Engineering Commons^™

A Computational Study Of Patch Implantation And Mitral Valve Mechanics, Dara Singh

Theses and Dissertations--Mechanical and Aerospace Engineering

Myocardial infarction (i.e., a heart attack) is the most common heart disease in the United States. Mitral valve regurgitation, or the backflow of blood into the atrium from the left ventricle, is one of the complications associated with myocardial infarction. In this dissertation, a validated model of a sheep heart that has suffered myocardial infarction has been employed to study mitral valve regurgitation. The model was rebuilt with the knowledge of geometrical changes captured with MRI technique and is assigned with anisotropic, inhomogeneous, nearly incompressible and highly non-linear material properties. Patch augmentation was performed on its anterior leaflet, using a …

Hot-Wire Anemometer Measurements Of Atmospheric Surface Layer Turbulence Via Unmanned Aerial Vehicle, Caleb A. Canter

Theses and Dissertations--Mechanical and Aerospace Engineering

An instrumented unmanned aerial vehicle (UAV) was developed and employed to observe the full range of turbulent motions that exist within the inertial subrange of atmospheric surface layer turbulence. The UAV was host to a suite of pressure, temperature, humidity, and wind sensors which provide the necessary data to calculate the variety of turbulent statistics that characterize the flow. Flight experiments were performed with this aircraft, consisting of a large square pattern at an altitude of 100 m above ground level. In order to capture the largest turbulent scales it was necessary to maximize the size of the square pattern. …

Indoor-Wireless Location Techniques And Algorithms Utilizing Uhf Rfid And Ble Technologies, Ann M. Whitney

Theses and Dissertations--Mechanical and Aerospace Engineering

The work presented herein explores the ability of Ultra High Frequency Radio Frequency (UHF RF) devices, specifically (Radio Frequency Identification) RFID passive tags and Bluetooth Low Energy (BLE) to be used as tools to locate items of interest inside a building. Localization Systems based on these technologies are commercially available, but have failed to be widely adopted due to significant drawbacks in the accuracy and reliability of state of the art systems. It is the goal of this work to address that issue by identifying and potentially improving upon localization algorithms.

The work presented here breaks the process of localization …

Trade-Off Balancing For Stable And Sustainable Operating Room Scheduling, Amin Abedini

Theses and Dissertations--Mechanical and Aerospace Engineering

The implementation of the mandatory alternative payment model (APM) guarantees savings for Medicare regardless of participant hospitals ability for reducing spending that shifts the cost minimization burden from insurers onto the hospital administrators. Surgical interventions account for more than 30% and 40% of hospitals total cost and total revenue, respectively, with a cost structure consisting of nearly 56% direct cost, thus, large cost reduction is possible through efficient operation management. However, optimizing operating rooms (ORs) schedules is extraordinarily challenging due to the complexities involved in the process. We present new algorithms and managerial guidelines to address the problem of OR …

Analysis Of Surface Integrity In Machining Of Cfrp Under Different Cooling Conditions, Arjun Nagaraj

Theses and Dissertations--Mechanical and Aerospace Engineering

Carbon Fiber Reinforced Polymers (CFRP) are a class of advanced materials widely used in versatile applications including aerospace and automotive industries due to their exceptional physical and mechanical properties. Owing to the heterogenous nature of the composites, it is often a challenging task to machine them unlike metals. Drilling in particular, the most commonly used process for component assembly is critical especially in the aerospace sector which demands parts of highest quality and surface integrity.

Conventionally, all composites are machined under dry conditions. While there are drawbacks related to dry drilling, for example, poor surface roughness, there is a need …

Design And Process Of 3d-Printed Parts Using Composite Theory, Jordan Garcia

Theses and Dissertations--Mechanical and Aerospace Engineering

3D printing is a revolutionary manufacturing method that allows the productions of engineering parts almost directly from modeling software on a computer. With 3D printing technology, future manufacturing could become vastly efficient. However, it is observed that the procedures used in 3D printing differ substantially among the printers and from those used in conventional manufacturing. In this thesis, the mechanical properties of engineering products fabricated by 3D printing were comprehensively evaluated and then compared with those made by conventional manufacturing. Three open-source 3D printers, i.e., the Flash Forge Dreamer, the Tevo Tornado, and the Prusa, were used to fabricate the …

The Effects Of System Characteristics, Reference Command, And Command-Following Objectives On Human-In-The-Loop Control Behavior, Seyyedalireza Seyyedmousavi

Theses and Dissertations--Mechanical and Aerospace Engineering

Humans learn to interact with many complex physical systems. For example, humans learn to fly aircraft, operate drones, and drive automobiles. We present results from human-in-the-loop (HITL) experiments, where human subjects interact with dynamic systems while performing command-following tasks multiple times over a one-week period. We use a new subsystem identification (SSID) algorithm to estimate the control strategies (feedforward, feedforward delay, feedback, and feedback delay) that human subjects use during their trials. We use experimental and SSID results to examine the effects of system characteristics (e.g., system zeros, relative degree, system order, phase lag, time delay), reference command, and command-following …

Circulation Dependence Of The Interaction Between A Wing-Tip Vortex And Turbulence, Farshid Najarzadegan

Theses and Dissertations--Mechanical and Aerospace Engineering

Vortices are present in many fluid flows and depending on the context they may be either beneficial or harmful for different systems or processes. Planar particle image velocimetry was used to examine the vortex evolution and its decay under different turbulence intensities and vortex circulation. The vortex decayed faster in the presence of high turbulence intensity. Vortex trajectories were impacted by turbulence intensity and vortex strength. Trajectories with no turbulence intensity had less variation. The vortex wandering amplitude decreased with growth of vortex strength. The vortex decay was confined to the core of the vortex, with the tangential velocity at …

Single-Degree-Of-Freedom Experiments Demonstrating Electromagnetic Formation Flying For Small Satellite Swarms Using Piecewise-Sinusoidal Controls, Ajin Sunny

Theses and Dissertations--Mechanical and Aerospace Engineering

This thesis presents a decentralized electromagnetic formation flying (EMFF) control method using frequency-multiplexed sinusoidal control signals. We demonstrate the EMFF control approach in open-loop and closed-loop control experiments using a single-degree-of-freedom testbed with an electromagnetic actuation system (EAS). The EAS sense the relative position and velocity between satellites and implement a frequency-multiplexed sinusoidal control signal. We use a laser-rangefinder device to capture the relative position and an ARM-based microcontroller to implement the closed-loop control algorithm. We custom-design and build the EAS that implements the formation control in one dimension. The experimental results in this thesis demonstrate the feasibility of the …

Design Process For The Containment And Manipulation Of Liquids In Microgravity, Chris Meek

Theses and Dissertations--Mechanical and Aerospace Engineering

In order to enhance accessibility to microgravity research, the design process for experiments on the ISS must be streamlined and accessible to all scientific disciplines, not just aerospace engineers. Thus, a general design and analysis toolbox with accompanying best practices manual for microgravity liquid containment is proposed. The work presented in this thesis improves the design process by introducing a modular liquid tank design which can be filled, drained, or act as a passive liquid-gas separation device. It can also be pressurized, and used for aerosol spray. This tank can be modified to meet the design requirements of various experimental …

News - Screven-Jenkins Regional Library, Sharon Blank

Georgia Library Quarterly

No abstract provided.

Asphalt And Adhesive Flow And Level Control, Kajan V. Moorthy

Electrical Engineering

This project entails the design of a flow control system to manage flow rates of asphalt to maintain constant thickness on the fiberglass sheet. By using the proposed system, the amount of scrap created by extremely thick or thin deposits on the mat would be reduced. The design of the proposed system aims to produce a flowrate of 10 gpm while it is also capable of self-correcting and shutting down when unsafe conditions occur. Selection of various components of the control system took place which included the Allen Bradley PLC and Flex I/O, power supply, radars for level sensor, and …

Investigation Of The Effect Of Vehicle Color On Safety, Deogratias Eustace, Fayez Khalaf Alanazi, Peter W. Hovey

Civil and Environmental Engineering and Engineering Mechanics Faculty Publications

No abstract provided.

A Learning-Centered Paradigm For Engineering Graphics And Design: Engineering Technology Students' Skill Gains And Capstone Preparation, Rustin Webster

School of Engineering Technology Faculty Publications

This descriptive non-experimental follow-on study investigates the extent to which a learning-centered paradigm in an engineering graphics and design course prepared undergraduate engineering technology (ET) students for senior capstone and how the course impacted vital professional and technical skills. A small 2016 case study (n = 10) showed that the course, which was approximately 5% passive and 95% active learning produced positive skill gains for ET students (Webster 2017). However, this follow-on study was needed largely from the inability of the 2016 case study to 1) identify and/or confirm data trends and 2) fully gauge the students’ preparation for senior …

Optimizing The Production And Injection Wells Flow Rates In Geothermal Field Using Artificial Intelligence, Muhammet Salih Ariturk

Graduate Theses, Dissertations, and Problem Reports (ETD)

In a geothermal field, power plants are designed for long-term electricity generation. Therefore, it is crucial to predict the future production and injection flow rates of the wells to determine the capacity of a power plant. In the designing of such power plants, calculations and estimations are based on the current future production, and injection flow rates and pressures in the geothermal field. Prediction of future production and injection flow rates also assist in building surface facilities with cost-efficient power plants. The most common problem in a power plant in geothermal fields is the inability to accurately estimate future expected …

Aptamer Functionalized Zinc Oxide Field Effect Transistors For Odor Detection, Michael D. Aldridge

Graduate Theses, Dissertations, and Problem Reports (ETD)

Odor detection and identification are complex processes, and tasks that currently only animals do well. There is a pressing need for an electronic nose, or eNose, with good sensitivity, selectivity, and speed that mimics that ability. Food quality control operations, environmental sensing, occupational safety, and the defense sectors all require systems that can rapidly and reliably detect trace levels of volatile organic compounds. The goal of this work is to create a biologically inspired device which can accurately detect and identify odors at concentrations consistent with the most sensitive biological systems.

In order to mimic a natural olfactory system, we …

Reconfigurable Reflectarray Antennas With Bandwidth Enhancement For High Gain, Beam-Steering Applications, Michael Trampler

Electronic Theses and Dissertations

Reconfigurable reflectarrays are a class of antennas that combine the advantages of traditional parabolic antennas and phased array antennas. Chapter 1 discusses the basic operational theory of reflectarrays and their design. A review of previous research and the current status is also presented. Furthermore the inherent advantages and disadvantages of the reflectarray topography are presented. In chapter 2, a BST-integrated reflectarray operating at Ka band is presented. Due to the monolithic integration of the tuning element, this design is then extended to V band where a novel interdigital gap configuration is utilized. Finally to overcome loss and phase limitations of …

Hybrid Multi-Objective Optimization Of Left Ventricular Assist Device Outflow Graft Anastomosis Orientation To Minimize Stroke Rate, Blake Lozinski

Electronic Theses and Dissertations

A Left Ventricular Assist Device (LVAD) is a mechanical pump that is utilized as a bridge to transplantation for patients with a Heart Failure (HF) condition. More recently, LVADs have been also used as destination therapy and have provided an increase in the quality of life for patients with HF. However, despite improvements in VAD design and anticoagulation treatment, there remains a significant problem with VAD therapy, namely drive line infection and thromboembolic events leading to stroke. This thesis focuses on a surgical maneuver to address the second of these issues, guided by previous steady flow hemodynamic studies that have …

Theoretical And Experimental Study For Tailoring The Electromagnetic Properties Of Conductive Materials, Jeffrey Jennings

Electronic Theses and Dissertations

Induction in leaded, implanted medical devices exposed to radio frequency (RF) magnetic fields during magnetic resonance imaging (MRI) produce Joule heating in adjacent tissues causing various issues, including death. Given the importance of MRI as a diagnostic tool and the growth in leaded device-related treatments, identification of a solution ensuring their compatibility is of great interest. Electromagnetic (EM) surface property tailoring in lead materials to change their inductive response by adding functionally-graded, heterogeneous surface layers is a possible solution. However, non-uniform EM properties introduce two challenges: the added complexity of analyses and characterization of the graded region. This dissertation addresses …

Investigation Of Flow Field Structures In A Rectangular Channel With A Pin Fin Array, Patrick Tran

Electronic Theses and Dissertations

Pin fin arrays are commonly found in heat exchangers, turbine blades, and electronic heat sinks. Fin arrays are extended surfaces that are used as turbulence promoters by inducing horseshoe vortex (HSV) and von Karman vortex (KV) structures. The horseshoe vortex are primarily studied in the leading edge of the blunt body, whereas the KV are formed in the trailing side. This study presents an experimental investigation of flow field structures and pressure loss on staggered pin fin array in the wake region, where KV are dominate. These flow structures increase the local levels turbulence and generate eddies that promote flow …

Safety, Operational, And Design Analyses Of Managed Toll And Connected Vehicles' Lanes, Moatz Saad

Electronic Theses and Dissertations

Managed lanes (MLs) have been implemented as a vital strategy for traffic management and traffic safety improvement. The majority of previous studies involving MLs have explored a limited scope of the impact of the MLs segments as a whole, without considering the safety and operational effects of the access design. Also, there are limited studies that investigated the effect of connected vehicles (CVs) on managed lanes. Hence, this study has two main objectives: (1) the first objective is achieved by determining the optimal managed lanes access design, including accessibility level and weaving distance for an at-grade access design. (2) the …

Design And Structural Analysis Of Morphing Wings, Nicholas Fernandez

Electronic Theses and Dissertations

Many natural flyers and marine swimmers can morph their wings during a number of unsteady maneuverings. With such wing morphing they are able to control the unsteady aerodynamic forces. A number of man-made flyers, such as unmanned aerial vehicles and micro air vehicles, fly in comparable Reynolds number range, but they are yet to acquire similar morphing capabilities as natural flyers or swimmers. Moreover, the knowledge of fluid structural interaction (FSI) of such morphing wings is not well developed. Hence there is a need to investigate the FSI of morphing wings. In this thesis, a morphing wing was designed and …

Gan Power Devices: Discerning Application-Specific Challenges And Limitations In Hemts, Andrew Binder

Electronic Theses and Dissertations

GaN power devices are typically used in the 600 V market, for high efficiency, high power-density systems. For these devices, the lateral optimization of gate-to-drain, gate, and gate-to-source lengths, as well as gate field-plate length are critical for optimizing breakdown voltage and performance. This work presents a systematic study of lateral scaling optimization for high voltage devices to minimize figure of merit and maximize breakdown voltage. In addition, this optimization is extended for low voltage devices ( < 100 V), presenting results to optimize both lateral features and vertical features. For low voltage design, simulation work suggests that breakdown is more reliant on punch-through as the primary breakdown mechanism rather than on vertical leakage current as is the case with high-voltage devices. A fabrication process flow has been developed for fabricating Schottky-gate, and MIS-HEMT structures at UCF in the CREOL cleanroom. The fabricated devices were designed to validate the simulation work for low voltage GaN devices. The UCF fabrication process is done with a four layer mask, and consists of mesa isolation, ohmic recess etch, an optional gate insulator layer, ohmic metallization, and gate metallization. Following this work, the fabrication process was transferred to the National Nano Device Laboratories (NDL) in Hsinchu, Taiwan, to take advantage of the more advanced facilities there. Following fabrication, a study has been performed on defect induced performance degradation, leading to the observation of a new phenomenon: trap induced negative differential conductance (NDC). Typically NDC is caused by self-heating, however by implementing a substrate bias test in conjunction with pulsed I-V testing, the NDC seen in our fabricated devices has been confirmed to be from buffer traps that are a result of poor channel carrier confinement during the dc operating condition.

Assessment Of A Surface Water Supply For Source And Treated Distribution System Quality, Angela Rodriguez

Electronic Theses and Dissertations

This study focused on providing a source to tap assessment of surface water systems with respect to (i) the use of alternative biomonitoring tools, (ii) disinfection byproduct (DBP) formation and control, and (iii) corrosion control. In the first study component, two water systems were microbiologically evaluated using adenosine triphosphate (ATP) bioluminescence technology. It was determined that microbial ATP was useful as a surrogate for biomonitoring within a surface water system when paired with traditional methods. Although microbial activity differed between distribution systems that used either chloramine or chlorine disinfectant, in both cases flowrate and season affected microbial ATP values. In …

Analysis Of Residual Stress And Damage Mechanisms Of Thermal Barrier Coatings Deposited Via Ps-Pvd And Eb-Pvd, Linda Rossmann

Electronic Theses and Dissertations

Thermal barrier coatings (TBCs) are critical to gas turbine engines, as they protect the components in the hot section from the extreme temperatures of operation. The current industry standard method of applying TBCs for turbine blades in jet engines is electron-beam physical vapor deposition (EB-PVD), which results in a columnar structure that is valued for its high degree of strain tolerance. An emerging deposition method is plasma-spray physical vapor deposition (PS-PVD), capable of producing a variety of customizable microstructures as well as non-line-of-sight deposition, which allows more complex geometries to be coated, or even multiple parts at once. The pseudo-columnar …

Improvement Of Data-Intensive Applications Running On Cloud Computing Clusters, Ibrahim Adel Ibrahim

Electronic Theses and Dissertations

MapReduce, designed by Google, is widely used as the most popular distributed programming model in cloud environments. Hadoop, an open-source implementation of MapReduce, is a data management framework on large cluster of commodity machines to handle data-intensive applications. Many famous enterprises including Facebook, Twitter, and Adobe have been using Hadoop for their data-intensive processing needs. Task stragglers in MapReduce jobs dramatically impede job execution on massive datasets in cloud computing systems. This impedance is due to the uneven distribution of input data and computation load among cluster nodes, heterogeneous data nodes, data skew in reduce phase, resource contention situations, and …

Interactive Perception In Robotics, Masoud Baghbahari Baghdadabad

Electronic Theses and Dissertations

Interactive perception is a significant and unique characteristic of embodied agents. An agent can discover plenty of knowledge through active interaction with its surrounding environment. Recently, deep learning structures introduced new possibilities to interactive perception in robotics. The advantage of deep learning is in acquiring self-organizing features from gathered data; however, it is computationally impractical to implement in real-time interaction applications. Moreover, it can be difficult to attach a physical interpretation. An alternative suggested framework in such cases is integrated perception-action. In this dissertation, we propose two integrated interactive perception-action algorithms for real-time automated grasping of novel objects using pure …

Simulation, Analysis, And Optimization Of Heterogeneous Cpu-Gpu Systems, Christopher Giles

Electronic Theses and Dissertations

With the computing industry's recent adoption of the Heterogeneous System Architecture (HSA) standard, we have seen a rapid change in heterogeneous CPU-GPU processor designs. State-of-the-art heterogeneous CPU-GPU processors tightly integrate multicore CPUs and multi-compute unit GPUs together on a single die. This brings the MIMD processing capabilities of the CPU and the SIMD processing capabilities of the GPU together into a single cohesive package with new HSA features comprising better programmability, coherency between the CPU and GPU, shared Last Level Cache (LLC), and shared virtual memory address spaces. These advancements can potentially bring marked gains in heterogeneous processor performance and …

Design, Development, And Testing Of A Miniature Fixture For Uniaxial Compression Of Ceramics Coupled With In-Situ Raman Spectrometer, Ryan Jordan

Electronic Theses and Dissertations

This thesis is about the design, development and integration of an in-situ compression stage which interfaces through the Leica optical microscope coupled with a Renishaw InVia micro-Raman spectrometer. This combined compression stage and Raman system will enable structural characterization of ceramics and ceramic composites. The in-situ compression stage incorporates a 440C stainless steel structural components, 6061 aluminum frame, a NEMA 23 stepper motor. Two load screws that allow to apply compressive loads up to 14,137 N, with negligible off axis loading, achieving target stresses of 500 MPa for samples of up to 6.00 mm in diameter. The system will be …

Design, Synthesis And Characterization Of Biomimetic, Bioinspired And Bio-Related Functional Polymers For Atmospheric Water Recovery, Abdullah Alqassar

Electronic Theses and Dissertations

Atmospheric water recovery in changing environments has received wide attention in environmental science and engineering communities due to rapid population growth and frequent droughts. This study is focused on the design, synthesis, and characterization of biomimetic, bioinspired, and bio-related functional polymers (b3p) to help resolve the water supply issue especially in arid or semi-arid regions. It is aimed to develop unique synthetic methods to access well-defined polymers with the aid of nanomaterials and metal to produce next generation polymer materials for better atmospheric water recovery. The design of such new b3p is bioinspired by some skin materials of biological species …