Engineering Commons^™

Characterization Of Zirconium Oxides Part I: Raman Mapping And Spectral Feature Analysis, Corey M. Efaw, Jordan L. Vandegrift, Michael Reynolds, Samuel Mcmurdie, Brian J. Jaques, Hui Xiong, Michael F. Hurley

Materials Science and Engineering Faculty Publications and Presentations

Raman mapping of sectioned zirconium cladding oxides was performed to analyze different spectral features before and after breakaway, as well as between zirconium and its alloys Zr-2.65Nb, Zry-3, and Zry-4. Oxide phase composition, or percent tetragonality, was defined to compare tetragonal to monoclinic zirconia. Percent tetragonality was spatially mapped to support distinction of zirconia phase distribution. A tetragonal-rich layer was seen at the metal/oxide interface, while post-breakaway samples exhibited increased amount of tetragonal phase in the bulk of their oxides. Spatial mapping of spectral peak location and half-width at half-maximum was accomplished to distinguish differences in stability mechanisms of tetragonal-rich …

Building Along The Railroad: Towns And Tourism In Michigan’S Eastern Upper Peninsula, Bridget Stoetzer

Honors Projects

The state of Michigan is not solely the lower portion or in other words the “mitten.” It is a combination of the lower and upper peninsula. The Upper Peninsula of Michigan (abbreviated the “UP”) is the upper portion of Michigan that is surrounded on three sides by three different Great Lakes: Lake Superior, Lake Michigan, and Lake Huron. It connects to the Lower Peninsula of Michigan by the Mackinac Bridge which crosses five miles across the Straits of Mackinac.

The counties of the Eastern Upper Peninsula are Alger, Chippewa, Luce, Mackinac, and Schoolcraft. They are marked by large stretches of …

Modeling And Improvement Of Electronic Waste Collection System: Case Study At Grand Valley State University, Quang Tran Nhat Nguyen

Masters Theses

Accelerated and advanced development of the electronics industry in the 21st century is creating the rapid obsolescence of electrical and electronic equipment. This causes one of the largest and unstoppable waste streams called electronic waste (e-waste). There have been obstacles in e-waste recycling, including the existence of the informal sector such as peddlers (a larger issue in developing countries) and insufficient consumer awareness. The ideal e-waste recycling system would be able to overcome these obstacles. To establish an effective e-waste recycling system, the first important step is to implement an e-waste collection system. To implement an e-waste collection system, many …

In Vivo Metabolic And Vascular Response To Hypoxia In Twist Knockdown Murine Breast Cancer, Brandon Sturgill

Graduate Theses and Dissertations

Twist transcription factor is often overexpressed in aggressive tumors. Although needed in early embryonic development for organogenesis, Twist is known to induce an epithelial to mesenchymal transition in cells. In cancer, epithelial to mesenchymal transitions can lead to increased motility and invasiveness. It has also been linked to metabolic reprogramming and increased metastatic risk. Furthermore, metabolic preferences can increase proliferation, enhance metastatic potential, and influence the site of metastasis. We hypothesize that Twist directly affects the metabolism of cancer cells. We expect to see in vivo what we have seen in vitro; Twist overexpression should promote a shift away from …

Optimized Production And Evaluation Of Cellulose Nanocrystals Derived From Pre-Extracted Kraft Pulp Of Different Wood Species, Gurshagan Kandhola

Graduate Theses and Dissertations

Production of nanocellulose from a variety of naturally abundant, locally available and industrially significant wood species provides an opportunity for diversifying the portfolio of traditional pulp and paper industries. The U.S. has a prolific forest products industry with a well-established infrastructure that could be utilized for optimized and customized production of cellulose nanomaterials. However, to achieve that, it is important to a) understand how biorefining strategies for complete fractionation of biomass affect the downstream processing of pulp into nanocellulose, b) maximize the yields of cellulose nanocrystals and nanofibers (CNCs and CNFs) from pretreated raw materials, and c) evaluate if the …

Interfacial Contact With Noble Metal - Noble Metal And Noble Metal - 2d Semiconductor Nanostructures Enhance Optical Activity, Ricardo Raphael Lopez Romo

Graduate Theses and Dissertations

Noble metal nanoparticles and two-dimensional (2D) transition metal dichalcogenide (TMD) crystals offer unique optical and electronic properties that include strong exciton binding, spin-orbital coupling, and localized surface plasmon resonance. Controlling these properties at high spatiotemporal resolution can support emerging optoelectronic coupling and enhanced optical features. Excitation dynamics of these optical properties on physicochemically bonded mono- and few-layer TMD crystals with metal nanocrystals and two overlapping spherical metal nanocrystals were examined by concurrently (i) DDA simulations and (ii) far-field optical transmission UV-vis spectroscopic measurements. Initially, a novel and scalable method to unsettle van der Waals bonds in bulk TMDs to prepare …

Dynamics Considerations Dedicated To Study Bodies In High-Altitude Free Fall, Michelle Carolina Rodriguez

Theses and Dissertations

The objective of this thesis is to develop a simulation model to study the dynamics of a rigid body in free fall. A set of 6 degrees of freedom (DOF) equations is developed to reflect the dynamic and trajectory characteristics over time. The simulation models a body dropped at different altitudes ranging from 30,480 – 39,624 m (100,000 – 130,000 ft). The trajectory of the body is analyzed using a mathematical nonlinear dynamics model. The mathematical model was developed in MATLAB and Simulink which can be modified for different geometries and conditions. The model was validated by testing that the …

Integration Of Inboard Propulsion In Shock Mitigating Membrane Hull Technology, Korrey Rotkiske

Theses and Dissertations

Membrane Hull Technology is a strength based marine vessel design concept that seeks to utilize the in-plane properties of fiber reinforced composites to generate a lighter weight vessel with inherent shock mitigation benefits. MHT has been applied on several Naval crafts yet the design features of inboard propulsion systems have not been addressed. Inboard propulsion systems are a very common form of propulsion used in many types of marine vessels especially larger vessels. This thesis seeks to overcome the inboard engine mounting challenges of MHT which limits use of this technology in the marine industry. The fundamental design elements of …

Deep Learning Models For Visibility Forecasting, Luz Carolina Ortega Gomez

Theses and Dissertations

This dissertation addresses the task of visibility forecasting via deep learning models using data from weather stations. Visibility is one of the most critical weather impacts on transportation systems. Low visibility conditions can seriously impact safety and traffic operations, leading to adverse scenarios, causing accidents, and jeopardizing transportation systems. Accurate visibility forecasting plays a key role in decision-making and management of transportation systems. However, due to the complexity and variability of weather variables, visibility forecasting remains a highly challenging task and a matter of significant interest for transportation agencies nationwide. This dissertation explores the use of deep learning models for …

Accelerated Relaxation In Disordered Solids Under Cyclic Loading With Alternating Shear Orientation, Nikolai V. Priezjev

Mechanical and Materials Engineering Faculty Publications

The effect of alternating shear orientation during cyclic loading on the relaxation dynamics in disordered solids is examined using molecular dynamics simulations. The model glass was initially prepared by rapid cooling from the liquid state and then subjected to cyclic shear along a single plane or periodically alternated in two or three dimensions. We showed that with increasing strain amplitude in the elastic range, the system is relocated to deeper energy minima. Remarkably, it was found that each additional alternation of the shear orientation in the deformation protocol brings the glass to lower energy states. The results of mechanical tests …

Blood Glucose Predictor, Jessica Patterson

Electrical Engineering

For my senior project, I perform data analysis using statistical methods to determine body metrics that correlate with blood glucose levels. Working with Dr. Tina Smilkstein, I take repeat measurements from 6 different volunteers to establish trends in bodily metric data. The data taken includes weight, body fat, pulse rate, VO2, blood glucose, blood pressure, hours slept, and quality of sleep. Using these values, I use the program MiniTab to view results.

A few examples of correlations with blood glucose found in this project are:

• Systolic blood pressure for females had a regression line of 124.0 -0.3366*Blood Pressure. This indicates …

Bitcoin Price Prediction Using Neural Networks, Vladislav Killiakov

Electrical Engineering

In this project, I will investigate the performance of several major neural network architectures for the task of Bitcoin price prediction. Bitcoin is a cryptocurrency that is recently becoming increasingly more popular, and more widely adopted as a financial instrument. As a result, more efforts have been made in the past several years to model and predict its price. However, to this moment a large portion of work on Bitcoin price modeling was done using statistical or classical machine learning techniques. At the same time, other artificial intelligence based prediction techniques, and specifically neural networks, have not been explored to …

Characterization Of Thermo-Mechanical Properties Of Copper Nano-Particles Infused Acrylonitrile Butadiene Styrene (Abs)- 3d Printed Specimens, Viswajit Talluru

Mechanical and Aerospace Engineering Theses - Archive

Now a days the use of metal nanoparticle infused polymer is becoming widespread, since the development of polymer with enhanced thermal properties are being used for the growth of electronic packaging industry. In this study, copper nanoparticles are mixed with the Acrylonitrile Butadiene Styrene (ABS) thermoplastic in varying mass proportions, to observe the changes in thermal and structural properties of ABS. As expected, the extruded wire with high nano-particle concentration exhibited much higher thermal conductivity than its raw ABS form. For the case of 2% copper nanoparticle infused ABS using one dimensional steady state heat flux method though extrude wire …

Introducing Digital Content To Kclc, Chad Briesacher

Theses

No abstract provided.

Publisher Correction: Pore Elimination Mechanisms During 3d Printing Of Metals (Nature Communications, (2019), 10, 1, (3088), 10.1038/S41467-019-10973-9), S. Mohammad H. Hojjatzadeh, Niranjan D. Parab, Wentao Yan, Qilin Guo, Lianghua Xiong, Cang Zhao, Mimglei Qu, Luis I. Escano, Xianghui Xiao, Kamel Fezzaa, Wes Everhart, Tao Sun, Lianyi Chen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The original version of this Article contained an error in Fig. 4. The x-axis labels in Fig. 4a, b were incorrectly labelled 'Diameter (mm)', rather than the correct 'Diameter (µm)'. This has been corrected in both the PDF and HTML versions of the Article.

Design And Sensitivity Analysis Of Ebg Stripline Common-Mode Filters, Marina Y. Koledintseva, Sergiu Radu, Joseph Nuebel

Electrical and Computer Engineering Faculty Research & Creative Works

Workflow of electromagnetic bandgap (EBG) common-mode (CM) filter design of edge-coupled differential pairs on a printed circuit board (PCB) and sensitivity of its characteristics to variations of geometrical and material parameters are discussed. A number of simple 20-GHz EBG CM notch filters for differential strip line pairs are designed using full-wave numerical electromagnetic modeling, fabricating, and testing. The cases of one and two strip line differential pairs crossing the EBG patches are considered. The modeled and measured mixed-mode S-parameters are analyzed as functions of geometrical parameters, including size and number of EBG patches, gaps between them, geometry and position of …

Design Of A Clc Testbed To Study High Voltage Capacitors, Christopher Francisco Martinez

Electrical Engineering Theses - Archive

Pulsed power systems rely on the interconnection of several unique stages for successful implementation. These stages can include, but are not limited to a prime power source, power conditioning circuit, intermediate energy storage, pulsed forming network, and the load. There are many possible intermediate energy storage devices that can be considered, two of which are inductive and capacitive. There are many advantages and disadvantages that each offer. Inductive energy storage is several times more energy dense than capacitive energy storage but most of the time, an opening switch is required to transfer the energy to the load and those are …

Spark Plasma Sintering Of Low Modulus Titanium-Niobium-Tantalum-Zirconium (Tntz) Alloy For Biomedical Applications, Nicholas Mavros, Taban Larimian, Javier Esqivel, Rajeev Kumar Gupta, Rodrigo Contieri, Tushar Borkar

Mechanical Engineering Faculty Publications

In metallurgy, titanium has been a staple for biomedical purposes. Its slow toxicity and alloying versatility make it an attractive choice for medical applications. However, studies have shown the difference in elastic modulus between titanium alloys (116 GPa) and human bone (10–40 GPa), which contributes to long term issues with loose hardware fixation. Additionally, long term studies have shown elements such as vanadium and aluminum, which are commonly used in Ti-6Al-4V biomedical alloys, have been linked to neurodegenerative diseases like Alzheimer and Parkinson. Alternative metals known to be less toxic are being explored as replacements for alloying elements in titanium …

Optical Spectrsocopy Of Murine Breast Tumor To Distinguish Indolent From Aggressive Disease, Joel Rodriguez Troncoso

Biomedical Engineering Undergraduate Honors Theses

Breast cancer accounts for 30% of all cancer. Metastasis is the primary cause of death among breast cancer patients. Additionally, current molecular profiling methods such as Oncotype DX, which are expensive and not widely available at all clinical facilities, only determine the risk of recurrence after treatment. Therefore, there are no current method capable of identifying metastatic patients in advance.As a result, there is an unmet clinical need to develop a cost-effective prognostic to differentiate between indolent and aggressive breast tumors. In this study, we implemented diffuse reflectance spectroscopy (DRS) system to evaluate functional changes in tumor xenografts originated from …

Introduction To Production: Philosophies, Flow, And Analysis, Charles R. Standridge

Open Textbooks

Production is a fundamental societal and economic activity. Production has to do with the transformation of raw materials into useful objects and includes the knowledge to complete the transformation effectively. Thus, production is a board topic ranging from philosophies about how to approach production such as lean and quick response manufacturing, how to organize production facilities, how to analyze production operations, how to control the flow of materials during production, the devices used to move materials within a facility, and strategies for coordinating multiple production facilities.

An integrated introduction to production is presented in a set of learning modules. In …

Gearbox Baffle Optimization, Megan Arduin

Masters Theses

Current literature reveals there is limited consensus on the placement of baffles within a gearbox to reduce churning losses. Thus, there is a need for a process to identify baffle clearances that result in maximum and minimum churning losses. There are two types of baffles: axial and radial. While both axial and radial baffles cause reductions in churning losses to various degrees, the focus is on the effect of radial baffles. The effect of a board (rectangular plate) baffle location on the churning losses of a single gear gearbox are evaluated using computational fluid dynamics (CFD) implemented in Ansys. Several …

Reasoning From Point Clouds, Joey Wilson

Computer Engineering

Over the past two years, 3D object detection has been a major area of focus across industry and academia. This is primarily due to the difficulty of learning data from point clouds. While camera images are fixed size and can therefore be easily trained on using convolution, point clouds are unstructured series of points in three dimensions. Therefore, there is no fixed number of features, or a structure to run convolution on. Instead, researchers have developed many ways of attempting to learn from this data, however there is no clear consensus on what is the best method, as each has …

Mobile Robot Platform, Sukhman S. Marok

Electrical Engineering

The Mobile Robot Platform is a research and development tool designed for researchers working in the field of robotics. The cost of existing mobile robot platforms can easily be in the thousands of dollars, leading many researchers to choose between spending the time to create their own platform or buying an expensive pre-existing solution. The Mobile Robot Platform proposed combines pre-existing open source software and hardware solutions, along with a strong mechanical base that is capable of navigating on flat surfaces. The robot is designed to have many of the necessary components needed for teleoperation as well as autonomous navigation. …

Free Space Optical Communication, Anuj Gohil

Electrical Engineering

Communication is key to day to day activities for all companies and people. Wireless communication has made us expect more from our tools. Radio Frequency has been the preferred medium for a couple decades, but there is a need for faster secure communication. Free Space Optical Communication is an alternate wireless communication system which uses optics to create a link. It utilizes low-power and converts an analog signal into digital pulses which are transmitted across space to a receiver. Its only caveat is its vulnerability under atmospheric obstacles. The goal of this project is to create a free space optical …

Pv Mppt Water Pump Controller, Jacob R. Lamkin

Electrical Engineering

The intention of this project is to create a low cost way to extract the maximum useful power from a PV module to power a water pump. This approach will yield maximum financial and technical accessibility for end users. The project was successful in powering a water pump from a PV module as desired, and the microcontroller driven control circuitry was capable of finding and maintaining operation at the maximum power point of the PV module. Due to the low performance of the buck converter used in this project, this approach was not as efficient as desired and would require …

Study Of Amorphous Boron Carbide And Hydrogenated Boron Carbide Materials Using Molecular Dynamics And Hybrid Reverse Monte Carlo, Rajan Khadka

Graduate Theses/Dissertations

We present a computational study of amorphous boron carbide (a-B_xC) models using Molecular Dynamics (MD) studied with Stillinger-Weber (SW) and ReaxFF potential. The atomic structure factor (S(Q)), radial distribution function (RDF) and bond lengths comparison with other experimental and ab initio models shows that a random arrangement of icosahedra (B₁₂, B₁₁C) interconnected by chains (CCC, CBC) are present in a-B_xC. Afterward, Hybrid Reverse Monte Carlo (HRMC) technique is used to recreate a-B_xC structures. The existing SW potential parameters of Boron are optimized for the α-rhombohedral (Icosahedral B_{12 …}

Demand-Side Load Management Using Single-Phase Residential Static Var Compensators, Muhammad Kamran Latif

Boise State University Theses and Dissertations

Distribution systems are going through a structural transformation from being radially-operated simple systems to becoming more complex networks to operate in the presence of the distributed energy resources (DERs) with significant levels of penetration. It is predicted that the share of electricity generation from DERs will keep increasing as the world is moving away from the power generation involving carbon-emission and towards cleaner energy sources such as solar, wind, and biofuels. However, the unstable behavior of the renewables resources presents challenges to the already existing distribution systems. One such problem is when the distribution feeder experience variable power supply due …

Fatigue Issues And Mitigation Strategies In Collegiate Aviation, Flavio A. C. Mendonca Ph.D., Julius Keller, Erik Levin, Aaron Teo

Publications

The reduction of fatigue-related accidents has been in the NTSB most wanted list since 2016 (NSTB, 2019).

Most research studies have focused on fatigue identification and management within the commercial and/or military aviation environments (Caldwell et al., 2009; Gawron, 2016; Sieberichs & Kluge, 2016).

However, collegiate aviation may be the most challenging in terms of fatigue mitigation. Flight instructors and students often have schedules which may increase the risks for fatigue.

Neural Network Classification Of Brainwave Alpha Signalsin Cognitive Activities, Ahmad Azhari, Adhi Susanto, Andri Pranolo, Yingchi Mao

Knowledge Engineering and Data Science

The signal produced by human brain waves is one unique feature. Signals carry information and are represented in electrical signals generated from the brain in a typical waveform. Human brain wave activity will always be active even when sleeping. Brain waves will produce different characteristics in different individuals. Physical and behavioral characteristics can be identified from patterns of brain wave activity. This study aims to distinguish signals from each individual based on the characteristics of alpha signals from brain waves produced. Brain wave signals are generated by giving several mental perception tasks measured using an Electroencephalogram (EEG). To get different …

Optimisation Of Rice Fertiliser Composition Using Genetic Algorithms, Retno Dewi Anissa, Wayan Firdaus Mahmudy, Agus Wahyu Widodo

Knowledge Engineering and Data Science

There are so many problems with food scarcity. One of them is not too good rice quality. So, an enhancement in rice production through an optimal fertiliser composition. Genetic algorithm is used to optimise the composition for a more affordable price. The process of genetic algorithm is done by using a representation of a real code chromosome. The reproduction process using a one-cut point crossover and random mutation, while for the selection using binary tournament selection process for each chromosome. The test results showed the optimum results are obtained on the size of the population of 10, the crossover rate …